Search Documents

By George E. Valadão, Iván A. Reyes, Mizraim U. Flores, Armando C. Araujo, Rubén H. Olcay

Dewatering tailings to higher grades than paste produces a stable deposit that typically does not require retention dams and is called a “dry stack.” A proposal of different dewatering techniques applied in the fine tailings produced after final desliming phase, obtained from the treating of phosphatic ores, is the main objective of this work. The dewatering techniques evaluated were column thickener, deep cone classifier, and hyperbaric filtration. Calcite and dolomite were the main mineral contained in the phosphate tailings and these have a very fine granulometry; the tailings presented different behaviours related to the dewatering technique applied. The test column thickener and deep cone classifier with the best operational parameters found to obtain a maximum percentage of solids in mass were ~ 71% and ~ 67%, with values of yield stress ~ 200 Pa and ~ 100 Pa, respectively. In the hyperbaric filtration, a cake with ~ 10% moisture was obtained. This indicates that the transportation conditions are not the same. The overflow turbidity levels obtained from column thickener and deep cone classifier test did not exceed the value 100 NTU, whilst for the filtrate of the hyperbaric filter obtained values ~ 800 NTU. It was possible to preliminary estimate the recovery direct of water, considering each dewatering technique for final disposal of the tailings. The best dewatering techniques obtained were in the following order for the disposal in phosphate fine tailings dams; the hyperbaric filter showed an excellent dewatering capacity with productions rates around 160 kg h− 1 m− 2 for moisture cake of 10%, followed by the column thickener and deep cone classifier with paste ~ 71% of solids (W/W) and high-density slurry ~ 67% of solids (W/W), respectively.

Dec 23, 2023

By J. Pascoe, J. H. van Laar, J. H. Marais, F. J. L. Matthee

Advanced measurement and verification (M&V) is a process where the impact of an energy initiative is determined in real time. Data prediction models can be used to predict and compare energy consumption with a predetermined baseline. Deeplevel mines can benefit from advanced M&V as the impact of operational changes can be identified in real time. Ultimately, this can ensure that informed decisions are made regarding energy management based on the impact and severity of the occurrence. Previous studies on advanced M&V do not account for operational changes to the model’s baseline. These changes can significantly impact the performance of both the mine and related activities. The aim of this study is to propose a method that can accurately predict the energy consumption of a deep-level mine regardless of operational changes. To achieve this objective, nine different data predictive modelling techniques were considered. The proposed method is based on the Moving Average (MA) modelling technique due to its simplicity, flexibility, and rapid development time. The coefficient of variation for the root mean square error (CV(RMSE)) was used to statistically analyse the modelling error. If the predictions exhibit an unsatisfactory CV(RMSE), the model dynamically adjusts to reduce the prediction error. The model was developed to adapt to operational changes in scenarios where the standard model becomes irrelevant. The method developed in this study was able to predict the future energy consumption of deep-level mines with an accuracy of 99%, improving the mine’s energy and finance management.

Dec 13, 2023

By Manoj Khandelwal, Bright Akuinor Tsidi, Newton Amegbey, Daniel Mireku‑Gyimah

One of the ambient effects of production blasting is flyrock. To effectively manage flyrock throw distance in mining, there is the necessity to successfully envisage blasting output without sacrificing the hazardous impact of flyrock which may result in fatality and operational shutdown. For flyrock throw distance prediction, velocity of detonation (VOD) and charge per bank cubic meter (CPBCM) are not usually included. This paper focuses on the use of support vector machine (SVM) regression to ascertain the impact of VOD and CPBCM on flyrock throw predictions. The machine learning models were linear support vector machine (LSVM), quadratic Gaussian support vector machine (QGSVM), fine Gaussian support vector machine (FGSVM), medium Gaussian support vector machine (MGSVM), and cubic Gaussian support vector machine (CGSVM). The outcome indicates that FGSVM was the most sensitive with a 4% improvement when VOD and CPBCM were included. As a result, the LSVM model provides a suitable AI competitive alternative tool for flyrock throw prediction in mining operations by incorporating VOD and CPBCM.

Feb 10, 2024

By Su Yang, Pang Shun, Xiaoding Xu, Guodong Yang, Hengfeng Liu, Meng Wu, Yuejin Zhou

By introducing the hydrochemical damage variable of coal gangue granular material, this paper analyzed the evolution law of gangue mechanical parameters with hydrochemical damage. By constructing a gangue damage model considering multifield coupling, the damage mechanism of gangue under multi-field coupling was revealed from the microscopical aspect, and the influence law of gangue damage mechanism on the dissolution of toxic substances under multi-field coupling was obtained: the conditions of Test 1 have the greatest influence on the porosity of coal gangue, and the damage of coal gangue is the greatest. Cu, Zn, Cd, and Pb are more easily leached under acidic conditions. The coupling effect of seepage, temperature, and chemical field can promote the formation of secondary voids, change the voids, and form migration paths in coal gangue. The kinetic model of toxic leaching of coal gangue under multi-field coupling can be well characterized by Elovich equation. The release mechanism of heavy metals is mainly manifested as delayed diffusion or dissolution in the early stage, diffusion and dissolution in the middle stage, and depletion in the late stage.

Nov 23, 2023

By · J. B. Boisvert, O. Leuangthong, T. Acorn

Optimizing final pit limits for stochastic models provides access to geologic and economic uncertainty in the pit optimization stages of a mining project. This paper presents an approach for optimizing final pit limits for a highly variable and geologically complex gold deposit. A heuristic pit optimizer is used to manage the effect of geological uncertainty in the resources within a pit shell with multiple uncertainty rated solutions. The uncertainty rated pit shells follow the meanvariance criterion to approximate the efficient frontier for final pit limits. Stochastic dominance rules are then used in a risk management framework to further eliminate sub-optimal solutions along the efficient frontier. This results in a smaller set of final pit shells that could be further analyzed for production scheduling. Additionally, the original solutions are analyzed for changes in the mining limits and two regions are targeted as potential regions for further exploration.

By Yousef Ghorbani, Jafar Abdolahi Sharif, Fatemeh Kazemi, Ataallah Bahrami

Kinetic models are the most important tool for predicting and evaluating the performance of flotation circuits. Gilsonite is a natural fossil resource similar to an oil asphalt, high in asphaltenes. Here, in order to determine the kinetic order and flotation rate of a gilsonite sample, flotation experiments were carried out in both rougher and cleaner stages. Experiments were conducted using the combinations of oil–MIBC and gas oil–pine oil, with one test without collector and frother. Five kinetic models were applied to the data obtained from the flotation tests using MATLAB software. Statistical analysis showed that the results of the experiment with oil–MIBC were highly in compliance with all models. Kinetic constants (k) were calculated as 0.1548 (s−1 ) and 0.0450 (s−1 ) for rougher and cleaner stages, respectively. Rougher and cleaner tests without collector and frother also matched all models well (R2 > 0.98), with k values of 0.2163 (s−1 ) and 0.284 (s−1 ), respectively. The relationship between flotation rate constant, maximum combustible recovery, and particle size showed that the maximum flotation combustible recovery and flotation rate were obtained in the size range of −250 + 106 μm in the rougher and cleaner stages. The combustible recovery and flotation rate were higher in the rougher flotation process than in the cleaner stage.

By David T. Kao

The energy situation the world faced during the decade of the Seventies resulted in actions throughout the free world to reduce its dependence on OPEC oil. Many nations heeded the indicators early in that decade and commenced efforts to reduce their oil requirements. Those nations which did not heed these warnings had the message brought to them more emphatically in the last portion of the decade with the further rapid and continuing rise in prices of OPEC oil. Furthermore, the demonstrated unstable nature of large oil-producing countries has made it clear to all free world nations that their energy demands of the future must be provided for by some more stable and assured supply. Now, early in the decade of the Eighties, we see the need for expanded use of coal as an energy supply to be essential. The result in 1980 and 1981 has been a great increase in demand for steam coal worldwide. In essence, a new business for the United States has developed in steam coal export. In the United States, the large growth in foreign demand for our steam coal is now well recognized and documented. A major impediment in meeting this growing demand became abundantly clear in 1980. This impediment is the congestion existing at U.S. coal export ports. With the recognition of this constraint, a plethora of activity has been observed in announcements for alleviating the problem by improving and expanding current export port facilities. In addition to improvement and expansion, an abundance of totally new facilities has been announced in an effort to find ways to meet this large demand in the new business of steam coal export. This is needed; and hopefully, many of these plans will be translated into action. While total implementation of all stated plans is not expected, much of the implementation depends upon large- scale dredging, large waterside ground storage sites, and improved handling equipments in the conventional type of export ports. The time and capital required for implementation is great, and environmental problems associated with dredging are substantial. Host significantly, and unfortunately, implementation that does include dredging our ports will still not permit use of the truly large colliers of 140,000 DWT and greater, which are evolving as the "state of the art" in long-distance sea transport.

Jan 1, 1981

By P. Valicek, M. Farren, R. G. B. Pickering, G. Harrison, P. van Dorssen, W. Joubert, H. J. van Rensburg

Introduction In South African metalliferous mines, stoping operations are largely confined to narrow, tabular orebodies making mechanization extremely difficult. Limited flexibility in terms of stope width has necessitated drilling by means of hand held, pneumatic rock drills at most of our operations. As the largest producer of platinum in the world, we drill in excess of forty million stope blast holes per annum. Cleaning of the broken ore is also done by conventional means—utilizing scrapers and scraper winches. Conventional methods such as these carry high costs in terms of risk exposure as well as labour intensity. The purpose of this paper is to describe the development of a long hole stoping system suitable for the narrow platinum reefs. The new system had to be substantially safer and more cost effective than conventional mining. We selected a site that was conducive to mechanized mining and set out the parameters that we considered would meet our requirements. We then conducted a feasibility study to evaluate the conceptualized long hole stoping system in terms of specific goals. An analysis of the proposed system identified the Key Performance Indicators (KPIs). One of the most critical goals was to be able to create a man-freestope. This would mitigate the safety risk associated with normal stoping operations, as well as the inefficiency cost previously referred to. Other challenges included setting targets for long hole accuracy, stoping width reduction and specific blasting system performance for long hole stoping. We also modelled a critical span that we considered to be inherently safe and to ensure hangingwall stability, throw-blastcleaning and overall system productivity. Anglo Platinum Research and Development and Sandvik Tamrock entered into an agreement for the supply of a specialized long hole-drilling machine. The system was implemented and tested by the mine with the support of the other participants. The results achieved met our expectations. It was demonstrated that with this method of mining it is possible to have a man-free/support-free stope face and to achieve a reduction in shaft head cost per ton whilst reducing dilution. Key performance indicators assessed during the trial •Safety targets •Mining layout •Drill rig •Production targets •Support requirement •Explosives requirement •Services requirement •Ore removal and cleaning requirement •Training requirement Safety targets All persons involved with the project had to adhere to the mine’s safety programme including the zero-tolerance campaign, and were required to report all hazards observed immediately. Mine personnel and Tamrock carried out a full risk assessment on the drill rig before transporting underground. A further risk assessment was carried out when the machine was in position underground. Mining layout See Figure 1 and Figure 2 for a detailed description. Drill rig The drill rig was a combination of a Secoma P-Low LC 10long hole feed and an Axera low profile carrier. The choice of this equipment was made through consultation with Tamrock Sandvik. All relevant design perimeters of the area to be mined were taken into consideration. Production targets

Sep 1, 2001

By J. J. Forbes

Problems connected with the incidence, effects, determination, and control of dusts are still much before the public, although more information is available to the layman than when Bulletin 400, of which this publication is a revision,5 was issued in 1937. Bulletin 400 attempted to assemble information in convenient form on various phases of the dust problem, largely in the mining and allied industries. This revision includes data that have accumulated since 1937 and some that appeared previous thereto but were not available to the authors at that time. The literature on this subject is so voluminous that no attempt has been made to include all published material or all types of dust diseases, but only to assemble some of the more outstanding data on several aspects of the subject.

Jan 1, 1950

By L. G. Billington

"The Agnew nickel deposit occurs in a major linear greenstone belt in the Archaean Eastern Goldfields Province of Western Australia, and has been subjected to mid-amphibolite facies nietamorphism of dynamic style. The largest dunitic ultramafic body in the Perseverance Block is host to the bulk of the nickel mineralization. The Perseverance Ultramafic is mineralogically zoned and has an embayed western margin against a mixed metasedimentarv-metavolcanic wallrock sequence.Three categories of nickel sulphide mineralization are concentrated on this western margin at the thickest part of the ultramafic exposure. Massive sulphides characteristically occur as contact mineralization, internal mineralization and as remobilized concentrations in vein form structures. Disseminated ore constitutes the largest volume of mineralized materials in the deposit and occurs in three separate shoots in en-echelon relation. Weakly mineralized 'cloud sulphide' zones surround and envelop the shoots and persist much further along strike. In the upper mine levels the shoots are truncated by a shear or crush zone, which inhibits geological knowledge to the south but marks a major fundamental structural break.Most of the ore types have suffered supergene alteration and there is a complex variable distribution of the mineralogical facies. The ore types have been metamorphically retextured, but the oreshoots can be characterized by their Ni tenor and some chemical ratios. S/Se values, PGF. and precious metal values are distinctly different from those of other nickel sulphide ores extracted.Despite intense structural and metamorphic modification of the mineralizations, some features support an original magmatic derivation for the sulphides. These include the localization of massive sulphide ore types on one marginal contact within an emhayment structure, the general distribution of disseminated mineralizations located immediately above the massive sulphides and the Ni/Cu, Ni/Co, Fe/Ni ratios of the oreshoots being similar to those of deposits that typify the intrusive dunite- associated class of nickel sulphide deposit. Varying S/Ni ratios between different shoots suggest a revision of the single magmatic intrusion model in favour of a changing composition between successive magmatic episodes."

Jan 1, 1984

By M. J. Pazuchanics

This U.S. Bureau of Mines report presents results from an ongoing investigation of the use of adaptive signal discriminating methods to distinguish between cutting coal and cutting mine rock. Bit-cutting forces and tool vibration were measured in the laboratory as a linear-cutting apparatus (LCA) made constant-depth cuts in coal, sandstone, and shale test specimens. A portion of the collected data has been analyzed and some preliminary results are given here. The influence of data bandwidth, data window size, number of signal features, and voting among classifiers on classification performance are noted. Results to date, based on ideal-cutting conditions and simple geologic materials, indicate that of the four classifiers tested there appears to be no single best classifier. Usually, classification accuracy showed slight improvement as the number of features considered for classification increased. The highest classification accuracies were achieved when voting was conducted among classifiers followed by voting among force components.

Jan 1, 1991

By Walter E. Dean

Twenty six samples of carbonaceous gold ores and associated rocks from outcrop and mine localities in northcentral Nevada were analyzed for concentrations of major. minor, and trace elements, total sulfur, and organic carbon. Q-mode factor analysis was used to define six distinctive carbonate, organic, and detrital associations of elements, and to group samples based on these associations. The trace metals that have clearly enriched the organic-carbon-rich samples are V, Zn, Ni, Cu, Cr, and Mo, although few of the samples could be considered "metal-rich" when compared to other organic-carbon-rich black shales. Rock-Eval pyrolysis was used to evaluate thermal maturity and hydrocarbon yield of the samples. Unfortunately, most samples were too thermally altered to be suitable for routine organic geochemical characterization of organic matter. The 813C values of organic carbon in rocks from different deposits have a trimodal distribution, but there is no clear distinction between the three groups of deposits that can be related to age, thermal history, or depositional environment.

Jan 1, 1987

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Bureau of Mines, United States Department of the Interior, with the cooperation of the University of Alabama and coal producers of Alabama, is making a series of washability studies to obtain technically and commercially important data from the productive coal beds of the State. Based on the system followed in these studies, this report consists of screen-sizing and sink-and-float data on the America and Pratt beds at Gorgas, Ala.SAMPLING AT THE MINESAlthough operations were discontinued in 1929, the accessible openings of the old Gorgas mines of the Southeastern Fuel Co. made possible the taking of samples from the America bed at three openings and from the Pratt bed at two openings. A sample was taken from the America bed at the Klondyke opening; a second was taken about 1 rile south of the Klondyke at the Musgrove America opening, and a third sample was taken about 1-1/2 miles south of the Musgrove-America at the Cricket Lodge opening. A sample was taken from the Pratt bed at Musgrove-Pratt No. 1, which is about 3/4 mile east of Musgrove-America, and a second sample was taken at Musgrove-Pratt No. 2, which is about 3/4 mile west of Musgrove-America. The samples ranged in weight from 1/2 ton to 1 ton and were equivalent to approximately a 2-ton sample from each bed. Figure 1 shows sections of the beds at the places sampled.In addition to the samples for washability study, a seam sample for analysis was taken at each of the places sampled. So as to give a representative seam sample for each of the two beds, these samples were combined in the laboratory in proportion to the thickness of the bed at the places sampled."

Jul 1, 1939

By M. Cai

"It is well known that Peak Particle Velocity (PPV) plays a critical role in triggering rockburst damage in burst-prone underground mines. To estimate the PPV distribution around excavations, advanced numerical modeling can be used. In wave propagation numerical modeling, velocity field is often assumed to be uniform around an excavation. However, it is observed that wave velocities near mine openings are not constant, but rather non-uniform. Wave velocity in a rock mass depends on many factors such as rock quality and confinement. In particular, confinement has a large influence on wave velocity. The confinement around an excavation is low at the wall boundary and increases gradually and reaches a constant value far away from the excavation boundary. Hence, stress redistribution due to excavation will have a profound influence on wave propagation in underground mines. A better understanding of the influence of excavation effect on wave propagation helps to interpret the field observation of rockburst damage and improve mine safety. For this purpose, a non-uniform velocity model need to be constructed and the influence excavation effect should be taken into account in numerical wave propagation modeling.In the present study, a non-linear velocity model is developed firstly by considering the influence of confinement on wave velocity. This model links wave velocity to confinement explicitly. A coupled numerical method is then developed and used to study the seismic wave pattern around excavations in underground mines. Two codes, FLAC and SPECFEM2D, are coupled in the analysis. The motivation of developing the FLAC/SPECFEM2D coupled approach is to take merit of each code, such as the stress analysis capability in FLAC and the powerful wave propagation analysis capability in SPECFEM2D. The coupling process is realized through three steps: (1) static stress redistribution around an excavation is analyzed in FLAC; (2) data for coupling analysis, such as non-uniform velocity field (based on the new developed velocity model), mesh, absorbing boundaries, etc., are generated by FISH functions in FLAC and passed to SPECFEM2D; and (3) wave propagation modeling is performed in the SPECFEM2D considering a fault-slip seismic source. Because stress redistribution around the excavation is considered, non-uniform velocity field for the SPECFEM2D model can be obtained and this is a notable feature of this study. Very large difference in the S-wave response in these two modeling approaches with uniform and non-uniform velocity fields can be seen from the modeling results.Using the FLAC/SPECFEM2D coupled modeling approach, accurate velocity models can be constructed and this in turn will help to produce accurate PPV distribution around the excavations. Accurate PPV contours can be used to identify high rockburst risk zones for improved dynamic ground support strategy."

Jan 1, 2015

By Batric Pesic

Silver dissolution with thiourea was studied by using the rotating disk technique. The major parameters studied were: thiourea concentration (0-0.5M), ferric sulfate concentration (0-0.5M), sulfuric acid concentration (0-0.5M), and the effect of many foreign ions (Mn, o.i, Co, Ca, Na, etc.). Temperature effect was studied in the range 5-35 .C. The activation energy was 5.4 Kcal/mole. The dissolution of silver was first order with respect to ferric sulfate, and the secord order with respect to thiourea. Among the additives, copper had a dramatically negative effect. The strong oxidants such as hydrogen peroxide and manganese dioxide were also detrimental for silver dissolution. Silver does not dissolve with thiourea in the absence of ferric ions. Sulfuric acid does not participate in the dissolution reaction either. Chemically, the most important parameter for silver dissolution is the ferric sulfate/thiourea ratio. Thus, in the solutions with excess of ferric sulfate, a solid silver-thiourea complex is formed, which precludes transfer of silver into solution. In the solutions with the excess of thiourea, the free thiourea reacts with formed solid silver-thiourea complex and silver goes into the solution. The solid silver-thiourea complex was characterized according to its chemical composition. The complex contains 6.54%C, 2.49\H, 14.77%N, 16.09%0, 21.62%8, and 37.13% Ag. This composition corresponds to a Ag2so4.3'1U.2ff:i0 compound The soluble silver species are present in the solution as the dimers of AgTU+3 complexes.

Jan 1, 1989

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By Launa G. Mallett, Charles Vaught, Dana C. Reinke, Lisa J. Steiner, Lynn L. Rethi, Kathleen M. Kowalski-Trakofler, Jr. Brnich, William J. Wiehagen

Safety and health professionals recognize that training is a critical element of any effective safety and health program. An extensive literature survey has led the authors to conclude that we are at the beginning of a revolution in training due to changes in the demographics of the workforce, the rapid growth of technology, and the universal ascendance of the information age. Of present major concern in the mining industry is how to provide appropriate training for an aging workforce and concurrently develop training for the expected influx of new and less experienced miners as older workers retire. This report explores the key issues in the changing safety and health training area as identified by the multidisciplinary team of NIOSH researchers who conducted the literature survey. Issues include generational differences between newer mine workers and the present workforce with respect to their physical, psychological, social, and cultural characteristics; their learning styles and work expectations; and the impact of technology. Some preliminary conclusions are offered for future training needs.

Jul 1, 2004

By W. D. Hausel

The Wyoming craton in the western United States is a favorable terrane for diamond deposits. The craton hosts a variety of ultramafic, ultrabasic, and ultrapotassic rocks. Additionally, a few hundred 'kimberlitic' heavy mineral anomalies and some geophysical and remote sensing anomalies indicate the presence of undiscovered, mantle-derived, pipes in the craton. The Wyoming craton is separated into a Wyoming 'archon' known as the Wyoming Province, and the Colorado 'proton' known as the Colorado Province. The 'archon' underlies much of Montana and Wyoming and continues north into Alberta and Saskatchewan; the Colorado 'proton' underlies much of Colorado and a small portion of Wyoming. Although most exploration geologists would consider the 'archon' the most favorable terrane for commercial diamond deposits, the 'proton' has produced more than 120,000 diamonds, while the 'archon' has not been very productive.

Jan 1, 1996