Search Documents

Editor's note: Biographical information about Ihor Kunasz, president, Newmont Uzbekistan, can be found in the February 1998 issue of ME, page 94 and in the May 1996 issue, page 92. Your personal assessment of the minerals business. Gosh! When I think about what has happened to the minerals industry over the past 27 years that I have been a member of SME! There have been fundamental structural changes in the industry. And I think that SME has been quite successful in coping with these changes as well. There has been a reorientation in how the minerals industry does business. It used to be called rationalization. Today we call it reengineering. In addition, the minerals industry has become more complex and more global. Shareholders have become more vocal and demanding in the management of the business, asking for protection of their shareholders' value. In the 1980s, a fundamental change was precipitated by a merger and acquisition fever in all industries, including the minerals industry. Raiders such as T. Boone Pickens put enormous demands on companies that, in turn, had to spend substantial management time to fend off the raiders. This resulted in a major restructuring of the mining houses. Today, for example, Anaconda, Kennecott and Amax are only historical names.

Jan 1, 1998

By G. D. Marshall, D. K. Sarin, V. E. Hampton

Ground support at the Thompson Mine emphasizes scaling, rock bolting and wire mesh screening on the backs and walls of all underground stoping and development areas and also full column grouted cable bolting in the bulk mining areas. This paper describes the equipment for the point anchored rock bolts as well as the full column cable bolts. Modifications in design and testing of all components and procedures has ensured a safe and efficient method of ground support for the mining conditions existing at the Thompson Mine.

Jan 1, 1983

By J. C. HEILMAN

THE Tri-State district, named from its situation in three States, lies in the northeast corner of Oklahoma, the southeast corner of Kansas and the adjacent part of Missouri east of the common corner of the above States. Production in the past eighty years has come from scattered mines within an area of some 35 miles east and west, by 25 miles north and south, although the actual area of the mined ground is but a small fraction of this territory. The land is leased from the individual land-owners, and the size of the tracts varies from 4.0 to 200 acres, the smaller sized tracts predominating. The leases usually call for a royalty of 7% to 15 per cent of the gross receipts of the concentrates, continuous operation during the life of the lease and specifically set out that no ores can be brought in from a foreign lease for custom milling nor can any ore be removed from the lease for milling. The ownership of the tailings remains with the land-owner.

Jan 1, 1931

By C. M. Davidson

Contamination of by-product: sulfuric acid, by dissolved oxides of nitrogen ('nitrates') occurs under some operating conditions encountered in sulfide roasting and smelting,, notably when oxygen-enriched air is used. This 'nitrate' lowers the value of the acid and increases the effective cost of smelter gas desulfurization. The present paper describes measures taken at one smelter acid plant to remove this 'nitrate'; it discusses the mechanism by which 'nitrates' in some cases concentrate in one part of the plant and can be purged for more efficient treatment; and it describes a process developed by C-I-L Inc. for removal of 'nitrates' from such a purge stream. Advantages of the process include very low reagent cost, recovery of all sulfuric acid values and safe handling of nitrous fumes.

Jan 1, 1983

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff' backflll to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By Syamujulu. M

Subsequent to the unbundling of the Zambia Consolidated Copper Mines (ZCCM) and the privatization of its constituent parts, the Konkola Copper Mines (KCM) represents a third of the original conglomerate. Now run by private hands as a sub group of Vedanta Resources Plc of India, KCM is strategizing on how best to deal with the operational issues of the organisation to resolve some of the difficult, logistical, environmental, mineralogical and metallurgical problems being encountered to tum them into opportunities as the company turns around. This paper reviews the options being put in place to provide appropriate solutions and strategies including the treatment of the highly siliceous low energy copper belt concentrates in its mining operations in Zambia.

Jan 1, 2007

By A. H. Tousley

Current problems in the cement industry are discussed and suggestions for solving them by modernization are made. Cement facility modernization is discussed in considerable detail with examples illustrating before and after conditions. Itemized are the improvements realized in better working conditions, better efficiency, higher production, lower costs, and better community relations. These improvements are related to the overall profitability of the particular plant or facility.

Jan 1, 1972

By Leandro Brunholi Ramos

As superligas de níquel apresentam boa combinação de resistência à corrosão e à oxidação, resistência mecânica, resistência à fadiga e à fluência, além de conseguirem operar em temperaturas elevadas, mantendo tais propriedades. A liga Inconel 625 vem sendo estudada como revestimentos, obtidos por cladeamento ou aspersão térmica, para tubos de aços ao carbono utilizados nas indústrias de petróleo e gás. Esses tubos poderão ser unidos pela técnica de soldagem, quando então se obtém uma junta Inconel-Inconel, e isso pode acarretar modificações nas propriedades dessas superligas. O presente trabalho objetiva obter uma junta soldada da liga Inconel 625 empregandose o processo de soldagem a arco utilizando eletrodo revestido Ni-Cr-Mo 3 e caracterizar o cordão de solda quanto à microestrutura, à dureza e à corrosão. A microestrutura foi avaliada por microscopia óptica; para dureza foi realizado perfil de microdureza Vickers ao longo da junta soldada; quanto à corrosão foram realizadas curvas potenciodinâmicas em três diferentes soluções: 3,5% NaCl, 3,5% NaCl + 0,01M Na2S2O3 e 3,5% NaCl + 1N H2SO4. Os resultados obtidos mostraram que a zona fundida tem microestrutura dendrítica, sendo a zona afetada pelo calor de aproximadamente 1,2 mm de extensão. A solda não alterou significativamente as propriedades de corrosão e dureza.

Aug 17, 2017

By Rafael Arthur Reghine Giorjão

Microestrutura e propriedades mecânicas de tubos de aço inoxidável superduplex SAF 2507 processados por soldagem por atrito com pino não consumível foram analisadas. Juntas de alta qualidade foram produzidas com sucesso utilizando ferramentas de nitreto de boro cúbico policristalino (PCBN), controle de força de 38 kN, velocidade de avanço de 50 mm/min, velocidade de rotação de 200 RPM. Ensaios de dureza e tração foram realizados, evidenciando aumento de dureza na zona de mistura e falha no metal de base. Simulações térmicas calcularam temperaturas globais máximas em torno de 1176 °C e diferentes ciclos térmicos ao longo da espessura da junta, conferindo diferenças microestruturais e mecânicas nestas regiões

Oct 30, 2017

By S Sullivan

A recent review of resource reports lodged to statutory bodies found geological models with oversmoothed or unrealistic lithological boundaries, many of which do not represent geological appearance in the field, pit or underground drive. The underlying data is often too complex or messy to be incorporated into the resource model and is thus a simplification of reality, to the detriment of the mining operation and its shareholders. Volumes can be over- or underestimated and subsequent grade predictions can be misplaced, combining to cause over- or understatement in resource reporting to stakeholders and statutory authorities. Domain models can be improved with new modelling techniques such as machine learning. However, with poor data or improper use of machine learning techniques, the conclusions can be just as misleading as with current techniques. Machine learning rarely offers a single ‘right’ outcome, rather a range of possible outcomes from the data provided. But importantly it can take advantage of the full richness of data for more informed models. Machine learning also provides confidence in its predictions so that uncertainty in the resultant models can be quantified and passed through for risk assessment during mine planning and operation. This paper will discuss the factors accentuating complexity in deposit modelling: data diversity, structural controls, chemistry, data volumes, process workflows and external non-geological constraints. A case study illustrates the risk of reducing or ignoring complexity, which can result in an overly simplified geological model.

Mar 22, 2022

By Christopher R. Winter

Mining companies have sharpened their refocus on their tailings management strategies in recent years. Mining companies with tailings storage facilities that use the upstream construction method have been challenged to track the evolution of industry standards, assess risks, revise design, and communicate design revisions with regulators. While many aspects of best practices and industry standards have evolved in recent years as an attribute of continual improvement, the controlling standard in the design of many upstream dams is understanding the foundational strengths of hydraulically deposited tailings. Following best practices and industry standards, Hibbing Taconite Company managed by Cleveland-Cliffs, began the re-evaluation of foundation strengths underlying a system of upstream dams at the company’s iron ore mine tailings storage facility in northern Minnesota. Initial steps in the re-evaluation require reanalysis of design parameters and recommendations by the Engineer of Record to the Owner, which was followed by a series of meetings with the Technical Review Board to determine an initial path forward. Once a path forward and preliminary design parameters were determined, the Owner engaged with the State Dam Safety Engineer to discuss and seek approval of the plan. With continuous regulatory engagement throughout the process, further refinement of the design parameters for the hydraulically-placed tailings foundations underlying upstream dams began with field and lab geotechnical investigations. Following a review of risk assessments and trigger actions response plans, Hibbing Taconite revised its tailings storage facility operating plans and budget for the coming years. Based on the findings of the re-evaluation, reanalysis, and refinement of parameters, a paradigm shift was realized with the hydraulically placed tailings foundation strengths underlying the upstream system of dams. This paper explores the path that the Hibbing Taconite Company followed to understand the paradigm shift and construct downstream improvements. The plan involved tailings re-characterization, dam design revisions, operating plan reconciliation, budget revisions, wetland permitting, dam safety permit amendments, storm water prevention plans, borrow materials studies, new concrete decant structures and the pursuit to recognize and be consistent with industry standards.

Feb 1, 2024

By Richard Giffen, Martha Gross, Luca Pellegrini, Pa Ousman Njie

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in Virginia includes parallel 1.5- mile (2.4 km) tunnels constructed using a tunnel boring machine (TBM). The TBM launching and receiving shafts were excavated within the footprint of two reclaimed islands abutting the navigation channel for the Port of Virginia. The shaft excavations—a circular tri-cell shaft at South Island, and a circular-rectangular twin-cell shaft at North Island—were supported by slurry walls up to 190 feet (58 meters) below the island surfaces. This paper describes specic design considerations for these shafts, as well as construction and uality-oversight aspects of their excavation and construction.

Jun 23, 2024

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015

By Aaron Samuel Young, Hiago Antunes Amador de Oliveira, William Pratt Rogers

Low commodity prices and lack of new high-grade deposits are pushing the mining industry for innovation. Lean mining has been vastly discussed in the past decades as a way to continuously improve mining efficiency. Although very theoretical, lean mining presents a set of new solutions enabled by the digital transformation that the mining industry is going through. This paper proposes a framework for a short interval control system with the purpose to allow timely responses by front line supervisors upon operational deviations. In the first part, the author briefly reviews concepts of short-range planning and lean mining. Then, the materials and methods used for the development of the short interval control system are discussed. Finally, alpha trial results are presented, and next steps discussed.

Oct 3, 2019

By M Edhammer

In 2007, Atlas Copco introduced an integrated tunnel scanner/profiler. The tunnel scanner, which is integrated into the control system, is mounted on the drill rigs, and replaces the previous variants of non-integrated scanner equipment. The Atlas Copco Tunnel Profiler, which is the name of this system, is currently being used by several contractors and mines on various projects in Scandinavia, Finland and Australia. Atlas Copco Tunnel Profiler can scan a tunnel of 65 m2 in just five minutes and is integrated with the computerised control system for the drill rig. This integration means that the results of scanning are immediately available for analysis on the computer screen both in the drill rig and in Tunnel Manager; a software for tunnel and drift planning.In 2008, a method was introduced for locating the drill rig with a total station navigation (TSN) system, integrated into the control system. TSN systems are used by a number of contractors in Scandinavia and Finland, as well as elsewhere in the world. Using a TSN for navigation is in itself not new, but when this is integrated with the control system it provides the opportunity for individual drill rig operators to use this method, without the direct assistance of a surveyor. TSN gives a very precise indication of the drill rig’s position in relation to the tunnel design. An accuracy of ±1 cm compared with the ±10 cm which is normally obtained with the traditional method using tunnel laser and sight plates on the drill rig’s feeder. The closer a tunnel is blasted to its planned profile, potentially the more is saved in terms of less shotcreting, extra rock bolting and other corrective work. A better quality tunnel is the key to better overall economy and today’s technology makes it possible to achieve that goal in every type of tunnelling and mining project.In addition to total station’s ­navigation and Tunnel Profiler, the concept of ‘high precision tunnelling’ also includes:•Software tunnel planning: Tunnel Manager, Tunnel Manager Pro and Tunnel Manager Measure while drilling.•Measurement While Drilling (MWD)collects the various drilling data and the interpretation of these for the early identification of variations in the rock.•Rig Remote Access (RRA) is a support for wireless or wired communication between drill rig and planning office. The result is being able to send planning data to the drill rig and to simultaneously have the facility for logged files to be sent from the rig to the office. There is an option of an external computer logging in to the drill rig’s control system to view menu screens and settings, and remotely troubleshoot and plan appropriate action.

Mar 21, 2011

By Casley G. E, Pritchard J

A single slurry fed fluosolids roaster was chosen to replace six multiple hearth roasters in the Copper Smelter at Mount Isa as part of the overall program to increase production from 100 000 to 155 000 tonnes blister copper per annum. The paper describes factors influencing the choice of the unit, problems encountered during the commissioning and details of the present roaster operation.

Jan 1, 1974

By C D. Pocock

Maintaining catch berm capacity in open pit mines through controlled blasting prevents production delays associated with managing risks associated with wall instability. A method has been developed to quantify the drill hole deviation of presplit holes at Century Mine. Different controlled blasting techniques are used to control wall quality and decrease the risk. The performance of presplit drilling, in terms of deviation from design has been investigated. A methodology has been developed to quantify the drill hole deviation in three dimensions. This methodology was converted into a series of algorithms capable of handling an extensive range of data. The methodology was applied to a case study at Century Mine to evaluate the performance of drilling on two presplit blasts. Overall, 67 drill holes were investigated in the case study. The drill hole deviation was quantified in terms of three parameters: skewness, linearity and drill hole deviation parameter. Methods for quantifying each parameter were developed. Skewness, a measure of the amount of curvature and linearity, was defined as the measure of the consistency of the gradient of the drill hole. Drill hole deviation parameter is defined as the average measured deviation of the surveyed drill hole position from the design position. Acceptable drill hole deviation tolerances for each of the defined parameters were developed by analysing drill hole deviation parameters with respect to implications to catch berm capacity. Verification of the methodology was confirmed through the comparing of the completed drill hole deviation results using both visual inspection and cross analysis for each of the three methods. Holes with an R squared value of less than 0.97 for skewed deviation were classified as having skewed deviation, while holes with a difference in gradient of 3.5 were classified as having linear deviation. The results show that 76 per cent of the drill holes had deviation. Of this, 19 per cent were skewed, 57 per cent had linearity and 12 per cent contained both skewed and linearity deviation.

Nov 8, 2011

By Francisco A. Flores, Rigoberto Torres

The Complementary Technical Standards of Mexico’s City Building Code do not mention the criteria to compute the bearing capacity of Steel H-piles. It is necessary to increase knowledge in using steel H-piles as foundation elements in very soft soils of Mexico City. Considering their applicability to reinforce structures as well as new foundations in confined spaces, this research is proposed to obtain the axial load capacity of piles at scale in laboratory. This paper describes the construction and testing of scale models in laboratory of steel H-piles to measure their axial compression and tension load capacity in the soft soils of Mexico City. Three types of piles were fabricated at scale. Tests were performed on individual piles and pile groups. Based on the axial load tests, the load-displacement curves are presented both in compression and tension. The analysis of the results is shown, and comments are given regarding the ultimate bearing capacity of piles. Recommendations are presented regarding the determination of the bearing capacity of these piles in the very soft soils of Mexico City.

Sep 8, 2021

By Robert C. Simpson, Ghada S. Ellithy

"There are several methods for estimating the axial capacity of drilled shafts installed in coarse-grained soils. Most methods estimate the ultimate capacity for side friction and tip resistance. Design capacity is then calculated by applying a resistance factor to the ultimate capacity. In reality, however, ultimate resistance may not be mobilized except after a significant displacement that is not structurally tolerated in either compression or tension modes.A full- scale load test is the best way to obtain the load settlement curve for a drilled shaft, especially in soil formations where accurate estimation of soil frictional properties from a field investigation may be difficult. This paper presents the results of a static, axial, compressive bi-directional load test, using the Osterberg method (O-cell test). The test was designed so that the shaft above the O-cell would move up and the shaft below it would move down when loaded. At the start of the test the concrete around the O-cell is fractured generally on a plane near the bottom of the cell.The test was designed to validate the design capacity of drilled shafts embedded into the Vashon recessional outwash (Qvro), which is a glacially derived sediment consisting of thick deposits of cobbly sand and gravel relatively free of silt and clay found in the Seattle, WA area. The test shaft consisted of a 2.5- feet (0.75 m) diameter drilled shaft. The test shaft was installed to a depth of about 47 feet (14.3 m) into this formation. A maximum load of 437 kips (1.95 MN) was applied during the test, in each direction. The maximum load was attained at upward and downward displacements of less than 0.1 inch (2.5 mm), respectively.Although the load test did not yield ultimate values, the results are compared to the design assumptions using methods adopted in the FHWA and AASHTO guidelines, which verified the adequacy of the design assumptions. We conclude that more emphasis is needed in the prediction of the service loads and corresponding mobilized displacement that may lead to a more cost effective design. It is also clear that more testing to higher loads could lead to more efficient designs on specific projects and generally as data is added to the local knowledge base."

Jan 1, 2015

By Benjamin B. Buensuceso III

Crosshole sonic logging (CSL) is a popular quality assurance and quality control method used to examine the concrete quality of cast-in place deep foundations, though the evaluation of the results is subject to certain limitations. One such limitation explored in this paper is the occurrence of false positives, where signal anomalies indicated by CSL test results are not necessarily indicative of imperfections in the foundation that could affect its performance. A case study of false positives evaluated in CSL records in a major infrastructure project in Metro Manila is presented in this paper. A detailed desktop evaluation and results from complementary high-strain dynamic load testing and low-strain pile integrity testing were used to evaluate the significance of the suspected false positive signal anomalies from the CSL test results. Recommendations for the proper interpretation and evaluation of CSL test results in Philippine practice, given the method’s limitations and examples presented, are also shared.

Sep 8, 2021