Search Documents

By Ke Yang

"Engineering practices have shown that the skip-fault longwall mining is frequently used when faults with offsets larger than 1 Om are present. Since the skip-fault longwall mining not only reduces the recovery rate of coal reserves, but also increases the cost due to developing another setup room on the opposite side of the fault and moves the longwall into it. The coal pillar so created induced residual stress in and thus affects the safe mining of adjacent coal seams. In order to investigate the influence on panel layout and retreat by a l 6.5m offset normal fault, the similar material simulation model was constructed based on the geological and engineering conditions of No.13 coal seam in the western district of Liuzhuang coal mine employing the down-dip longwall mining. The characteristics of deformation, movement and failure of the overlying strata and abutment pressure when the face cut through the hangingwall and footwall of a normal fault were obtained. There were significant differences between the hangingwall and footwall as conformed by the equilibrium structure model. The results showed that superposition of the tectonic stress from a normal fault of large offset and that induced by mining is one of key factors that lead the severe pressure difficult to control during panel retreating from the hangingwall to footwall. Accordingly, the technical solutions for a fully mechanized mining face directly cutting through the fault are presented and optimized, and the applications of the technical solution in Panels 171301and171303 of Liuzhuang mine enabled them to complete the mining safely and efficiently. INTRODUCTIONFaults have been one of the important technical factors in underground coal mining l1-2i. Engineering practice has shown that the methods of mining through the faults depend on the seam thickness, seam dip angle, offset of fault throw, equipment height, rock strength, and advancing direction l3-5l. In the fully-mechanized longwall mining, the face normally proceeds to cut through the fault directly if the offset of the fault less than 5m, and to skip Uump) the fault if the offset is larger than 5m. In the former case, the most important problem is to efficiently control or avoid roof fall accidents (i.e., crushing, falling, pushover, and rock burst). In the latter case, the most important problem is very expensive to drive a new setup room and move the face equipment to it. The skipped coal pillar may poses problems for mining in adjacent seams."

Jan 1, 2016

By L. M. Cenegy

The formation of scale is common in gold ore processing plants. A working definition of scale, applicable to the various scaling conditions found in gold ore processing plants, would be: "a hard, tightly adhering deposit formed in place by the precipitation of calcium-bearing mineral compounds from water". The most common scale found in gold processing plants is calcium carbonate (CaCO3) although calcium sulfate (CaSO4) is occasionally a problem.

Jan 1, 1990

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack.

Jan 1, 1949

By L. Muñoz, L. Steffen, J. Alarcón, W. Vilas

Today, mining operations close to communities face increasing challenges, especially in their drilling and blasting operations. Proper management of environmental impacts is important to guarantee their license to operate and to provide sustainability to the mining business in the long term. Blasting is an event that generates impacts such as vibrations, noise (airblast), projections (flyrocks), ejection of dust and fumes (when there is a deficient detonation of the explosive). If any of these variables exceed the established regulations, sanctions can be generated and even lead to stop mining operations. The goal of this work is to present a review of different techniques, concepts, technologies, simulation software and monitoring / control tools to minimize the environmental impact generated by blasting. For which, a case study of a big scale open pit mine in Brazil with operations close to a community will be presented. An adequate management model, combined with good operational practices, the use of new technologies, enable a safe operation without incidents with the communities. In this way, building trust with neighbours, maintaining the license to operate, and helping mining industry to mobilize resources essential for progress in a sustainable way

Jan 1, 2024

By Fabio Loyola

La planta de adsorción de carbón de Pampa Larga (CIC_PL) es la principal planta que contribuye a la producción de Yanacocha. Las pérdidas de oro ocurren a partir de la solución gastada que va a la planta de tratamiento de agua y luego se descarga al medio ambiente. Se identificaron dos oportunidades de mejora para lograr un mejor desempeño de la planta. Una oportunidad está relacionada con mejorar la adsorción de oro sobre el carbón en una solución con alto contenido de cobre. La otra oportunidad está relacionada con mejorar el control operativo de la planta de carbón, al usar el manual corporativo de carbón activado, como también aumentar la actividad del carbón y optimizar la cantidad de carbón en los tanques del circuito de adsorción.

Sep 29, 2023

By Daniel Augusto Godinho de Carvalho

At thyssenkruppCSA, a positive heat balance at BOF process is faced, mainly because of low utilization of scrap and plant design. A singular logistic concept for hot metal transport between blast furnace and steel plant was established to optimize transportation and energy balance. Up to 80 kg of iron ore pellets/t steel is necessary for 340t BOF heat balance. In order to accomplish this challenge a stable blowing process, intensive operational development have been successfully executed: slopping rate reduction of 80% achieved without changing the blowing time. This paper describes steps and results of this development.

Oct 30, 2017

By V. Rajaram

The Parachute Creek Member of the Green River Formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch Joint Venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1977

By O Dominguez

Significant value can be added to ore supplied from the mine to the mill by measuring its quality in real time and performing grade control additional to that within the mine. Responsibility for ore quality between the mine and mill stockpiles is not always clear due to operational siloes so geologists and mining engineers need to be involved collaboratively with metallurgists to optimise ore value prior to processing. Sensors, such as the GEOSCAN-M which utilises high specification Prompt Gamma Neutron Activation Analysis (PGNAA), that measure conveyed ore flow representatively (continuous and fully penetrative) and in real time have been used in the minerals sector since 2003 and have been successfully applied in multiple commodities. Quality can be measured within the mine where material is conveyed underground or in-pit. Bulk ore sorting is used to divert increments of waste from the ore stream to upgrade material sent to the crushed ore stockpile (COS) as well as to create run-of-mine (ROM) stockpiles of different qualities to maximise blending opportunities and accommodate processing priorities, eg blending out deleterious content. The real time composition measurement can be combined with moisture and fragmentation analysis data for improved ore type characterisation, to control ore blending, for feedback to the mining schedule and block model reconciliation, and feed forward control for grinding and processing operations. The paper discusses various parameters measured and derived in existing operations that are used to maximise coarse waste rejection and metal recovery, optimise plant feed quality consistency, and reduce consumables; power, grinding media, water, reagents, and minimise fine tailings generation. Innovative geometallurgy applications are also discussed.

Mar 22, 2022

By M Player, R Klug, N Schwarz

There are several technologies available for thickening and dewatering of mining process slurries. The most commonly used are thickeners and filters, but technological developments have made solid bowl decanter centrifuges a viable option and their use, as a modern and alternative technology, is being considered more and more. In terms of tailings, the main goal for all mine operations is to minimize operating costs and the environmental impact of the disposed material. The high potential risk of wet tailings storage in tailings dams is causing this technology to become unpopular, and there is a strong drive in many parts of the world, by governments, communities and environmental agencies to limit any further construction and use of such facilities. For the alternative disposal method of dry disposal of tailings, two aspects of the process have to be evaluated, namely the maximum dryness of the separated solids and the maximum liquid recovery. For most mining operations dry disposal is a new concept. Presenting these companies with examples of operations where this processing option has been successfully applied and proven, will help them to adapt to the changing requirements in the future. Focus has been placed on adapting decanter centrifuges to the mining environment. Modern decanters stand out in terms of their small footprint, low water demand, high availability and their high degree of automation, combined with the excellent cost / performance ratio. Decanter centrifuges have started to play a key role in applications such as tailing dewatering, drilling and tunnelling muds processing, hydrometallurgical processes of gold, nickel or zinc and separating crud in solvent extraction plants. This paper will present advantages of decanter centrifuges compared to the traditional technology and corroborate these advantages by case studies.

Jul 1, 2021

By Arthur W. Ruff

Estimated reserves of high-grade iron ore at Serra dos Carajás total 16 billion metric tons and have an average grade of 66.7 percent iron, 2.2 percent combined silica and alumina, and 0.05 percent phosphorous on a dry basis. Hematite is predominant and no significant sulfur or other deleterious elements are present. Figure 1 illustrates the comparative magnitude of the Carajás reserves. Serra dos Carajás is located in northern Brazil, about 550 kilometers southwest of Belém, Pará. It is six degrees south of the equator between the Xingu and Tocantins Rivers. Both rivers flow northward toward the Amazon River. The greater part of the area is covered by thick jungle, and the most practical means of access is by air. Figures 2 and 3 show the location of Serra dos Carajás. Figure 4 shows the distribution of the major iron-ore deposits.

Jan 1, 1973

By G G. Paine, C V. B Cunningham, G Harries

The companies of the ICI Explosives Group have successfully used a wide variety of internal computer codes including BOBCAT, KUZ-RAM, ICRAX, XPLODE, BLEND, 3CRACK, MICBLAST, DETON, etc. In recent years the extensive experiences across ICI have been combined into a single compatible model engineered to worldwide technical service and customer needs for the prediction and assessment of blast results.

Jan 1, 1987

By A. T. Yu

As the first loads of Noamundi iron ore rumbled into the new 54-in. Gyratory Crusher on March 30, 1968, one of India's largest and most modern iron ore processing complexes began operations. The completion of the $13 million mining and processing complex brought to a successful conclusion the second chapter of a phased expansion program initiated in 1958 by India's gigantic Tata Iron and Steel Co. The completed complex will yield annually 2.5 million tons of washed, sized ore and sinter fines destined for Tata's furnaces at Jamshedpur. Hewitt-Robins Div. of Litton Industries was awarded the turnkey project on the basis of world- wide competitive bids. Eighty miles southwest of the city of Jamshedpur, Noamundi lies on an approximate geographic grid of 22º-5' latitude north and 85º-30' longitude east. The mine is approximately 600 ft above sea level.

Jan 11, 1968

By Carl L. Kaiser

This abstract discusses selected recent technology developments at the Deep Submergence Lab at the Woods Hole Oceanographic Institution aimed at fundamentally changing the nature and scope of AUV operations in the deep ocean. The Autonomous Underwater Vehicle (AUV) Sentry is described in its current configuration with discussion of emerging capabilities. Telepresence enhanced AUV operations are discussed including moving both operations and data processing personnel off the vessel. Autonomous Surface Vessel (ASV) aided AUV operations are discussed including recent experiments where an ASV provided both navigational aiding and a satellite based relay for acoustic communication of telemetery and mission redirection. New flexible communications strategies to perform intervention and manipulation tasks from an untethered vehicle are discussed. The abstract concludes with a brief discussion of industrial collaborations, including the newly launched Center for Marine Robotics.

Sep 14, 2011

By K Lee, L Mann, J Bygrave, G Sheldon

Ausmelt is supplying commercial quantities of an alkyl hydroxamate flotation collector AM28 for flotation of oxide and supergene base metal ores and tailings. AM28 is a non-hazardous product used as a ten per cent to 50 per cent solution in dilute potassium hydroxide. It is a selective flotation collector for oxide or oxidised base metal minerals and replaces conventional sulfidisation for oxide mineral flotation. At Radio Hill, the AM28 is used in conjunction with traditional sulfide collectors, which allows simultaneous flotation of oxide and sulfide copper minerals. The Fox Resources Radio Hill copper concentrator near Karratha, Western Australia, is currently configured to treat supergene copper ore sourced from the West Whundo open pit. This Archean VMS type copper deposit has been deformed and remobilised with uplift, erosion and weathering to form a significant supergene zone. The sulfide copper minerals present in the upper zone are digenite and chalcocite with lesser chalcopyrite and covellite. Oxide copper minerals present include cuprite, with lesser malachite and azurite. Gangue minerals include quartz, talc and chlorite. Plant trials at Radio Hill are reported for supergene West Whundo ore, where the AM28 was stage added into the circuit at nominally 80 g/t. Plant data over three months shows the copper recovery increased consistently from around 50 - 60 per cent to above 70 per cent when AM28 was added. This has been proven statistically. The grade of the concentrate was consistent with and without AM28, at nominally 22 - 24 per cent copper.

Jan 1, 2007

By John R. Marks

Introduction An engineer is a builder and a problem solver. He uses knowledge of the properties of matter and energy to furnish the needs of society. Engineers form the bridge between scientific researchers and the general public, most of whom are technologically illiterate. Mining, metallurgical, and petroleum engineers extract minerals from the ground and process them into usable forms. Then, other engineers further process them into society's needs. Minerals engineers deal with more uncertainty than other engineers. Each ore deposit has its own personality and each ore is metallurgically unique. Minerals engineers, therefore, must be flexible, often applying larger safety factors and contingencies than other engineers, and frequently functioning as a jack of all trades. A minerals engineer can work in coal, oil, oil shale, base metals, ferrous metals, precious metals, industrial minerals, strategic minerals, or in exploration. Other mining jobs include banking and financing, education and research, marketing and sales, and government. As a minerals engineer, you may be among the first to work on the ocean floor or the moon. College Preparation A difference between college and industry is the type of problems to be solved. A typical college problem has an exact answer derived from given information. An industry problem is more apt to have a solution chosen from a number of alternatives. Information required for the solution is not given. It must be measured, calculated, looked-up, estimated, or otherwise derived. Solutions involve trade-offs, economics, and human factors, as well as application of physical laws and theory. When a college problem is answered, you move on to the next one. In industry, however, the headaches may just be starting with the implementation of the solution. Students often complain that they see little use for the theory they are learning. This is valid. A good professor will link theory and practice. Another difference between college and industry is the price of failure. In college, you can make a half-hearted effort in an assignment and take your C or D. On the job, however, poor engineering results in potentially effective projects being rejected and unsound projects being undertaken. Poor performance results in cost overruns, schedule holdups, oversights, disgruntled employees, irate bosses, unsafe structures, and unreliable systems. The costs are time, money, and possibly lives. The student pays the university for his work - not the other way around. So the rewards for good schoolwork often seem nebulous. But education must be viewed as an investment. Working for good grades will help you think better, learn more, receive better job offers, and perform more effectively on the job. There is no substitute for hard work. Avoid taking the easiest electives. If you desire a more liberal education or dislike rigorous physical sciences, mathematics, or engineering courses, change majors. Remember, you are training to be an engineer, not a computer programmer or market analyst. At least one summer of industry employment is necessary for minerals engineering students. The sooner you gain actual experience, the sooner you will know whether to change majors. Most large companies hire students during summer. It is best to send out applications around Christmas break. First and second year students usually work as laborers. Upper-classmen may work as engineering technicians. Students must sometimes choose between returning to a company at a higher position or trying a different company at a lower position, for more varied experience. Both alternatives have advantages. Do your best on these summer jobs. The company is watching. If you do well, the chances are good you will get a job offer when you graduate. Good references are important when you begin job hunting. Interviewing occurs near the end of your school career. The standard procedure is to send your resume with a cover letter to each company you are interested in. The resume for a graduating engineer with little experience need not exceed one page. The cover letter must be written for the individual company.

Jan 2, 1985

By Brian R. Castle, James J. Scott

INTRODUCTION Referring to a ground support system as a 'band-aid' borders on getting cute, but the application of cable slings in U.S. mining is somewhat analogous. Where problems in the roof or rib require additional support, the versatile cable sling is the answer in a variety of conditions. To fully understand how and why cable slings are used today we must briefly review their development history. Much of the thrust over the last five to seven years in ground support fixtures has been the development of hybrid systems. Taking the best of two or more existing roof bolt fixtures and marrying them into a new fixture which exhibits the good characteristics without the bad of the parent systems. Resin point anchored mechanical bolts, continuous threaded rebar bolts, and others have all be- come important fixtures in rock mass stabilization. HYBRID GROUND SUPPORT SYSTEM The cable sling system is also a hybrid, both in its parentage and in its ground support characteristics. See figure 1. Cable slings combine the techniques of cement. grouting high-strength cables, Friction Rock Stabilizers, and truss-like suspension into a versatile and high- strength ground support system. 1/2" high-strength cable is cement grouted in place in a manner similar to pre-

Jan 1, 1983

By J. Janeson

Wall control at the Pipe Open Pit is of primary importance in ensuring the long-term stability of the operation, while keeping costs to a minimum. Blasting techniques have been adapted to the variations in competence and structure of the wall rocks. A portion of the perimeter wall is being developed in incompetent peridotite . A recent change in pit slope design provides a wide safety berm on alternate benches. A support program which consists of pinning the crests of wide berms with vertical reinforced concrete dowels and horizontal bolting of walls shows evidence of increasing the stability of the pit walls. This paper describes the blasting and support techniques which are contributing to successful wall control in the Pipe operation.

Jan 1, 1979

By M. H. Allan

"This paper presents the geographic and geological setting of Saskatchewan Power Corporation's Poplar River Mine in south-central Saskatchewan, about 8 miles from the U.S. border. Generally the mine, which is being expanded to four million tons per year, is in an extremely disturbed geological area with severe dewatering problems. The lignite coal, which is strip mined, is supplied directly to an electric power generating station by means of a 7-mile unit-train private railroad.A number of unique reclamation and socio-economic problems were encountered because of the proximity to the U.S. border and because of the lack of experience of the regulatory authorities in projects of this kind. These are described in some detail, as well as the performance of one of the largest draglines in Canada. IntroductionThe Saskatchewan Power Corporation is a publicly owned utility which has the franchise to supply electricity and natural gas to all customers within the boundaries of Saskatchewan.Saskatchewan is a province which can almost be divided in two: the populated southern portion, principally devoted to farming, and the northern portion which is mostly on the Precambrian Shield and consists of lakes, rocks and muskeg. This portion is largely uninhabited except for a number of small villages. However, in the last few years there has been considerable mineral exploration and development, notably for uranium. This has helped considerably in the diversification of the basic agricultural economy of the province.Saskatchewan consists of 251,700 square miles, 761 miles north to south and an average of 335 miles east to west. It has a population of approximately 960,000, giving a population density of four persons per square mile. The Saskatchewan Power Corporation supplies 357,249 electrical arid 221,378 natural gas customers."

Jan 1, 1982

By Joe M. Short

More than eighty years ago, in what we generally consider a more leisurely age, workers and engineers began the construction of the longest railroad tunnel in the world. When completed, the Simplon Tunnel ran more than twelve miles through the alps to connect Switzerland and Italy. Work began in 1898 and the tunnel was completed in 1905. In all it took about seven years to build one of the world's great tunnels. More than seven years ago, in what was hoped to be a rapid and constructive to the deaths of 38 workers in two spectacular tunnel disasters in 1971, the secretary of Labor's Construction Advisory Committee on Safety and Health began in January 1972 a search for an effective standard on tunnel safety. Much hard and useful work has been done, especially by the construction advisory committee' but more than seven years later, we still don't have a tunnel standard. We may speculate that, when the Simplon Tunnel was completed, workers and their bosses assembled to celebrate their achievement and to count their casualities. We have no need to speculate on the lack of achievement up to this time. An so far as I know, the bureaucrats have suffered no casualities except perhaps some unreported cases of ring-around-the-color. The only moral I can draw from all this is thai it is easier to penetrate solid rock than it is to get through bureaucratic fog. We can only hope that OSHA will finally take advantage of the work which was finished years ago and complete the actions necessary to give us a tunnel standard. Having made my point, I could stop my remarks right now; but

Jan 1, 1979

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022