Search Documents

By Keith G. Wallace, Justus B. Deen, Daniel J. Brunner

This paper describes the impact of natural ventilation pressure (NVP) on the Nuclear Waste Isolation Pilot Plant in New Mexico (WIPP). The WIPP site is a U.S. Department of Energy underground facility for the disposal of low level radioactive transuranic defense generated waste. Because the facility is designed for the storage of nuclear waste, special design considerations are necessary to ensure containment of potential radioactive releases. The main design considerations which influence the ventilation system are the requirements of separate air splits for mining and storage operations and of air filtering before atmospheric discharge in the event of a radioactive release. The leakage between the two air splits must always be from the mining area to the storage area. The transient effects of natural ventilation pressures, caused by seasonal and diurnal surface temperature changes, impact the ventilation characteristics throughout the facility. This paper discusses the measurements taken to quantify the changes in NVP and the engineered systems designed to mitigate against the effects of NVP.

Jan 1, 1991

By P. S. Newall

As part of a much larger research project, factor analysis was employed to help interpret and compare the geochemical signatures produced by two different sample media; a traditional -80# soil fraction, and a coarse float. Both sample types were collected by hand auger from the extension zone of the Redmoor sheeted-vein complex and analyzed -for 19 major and trace elements. The rationale behind the study infers that the geochemical anomalies produced by wallrock alteration around such targets can be better detected in the lithogeochemical rather than the soil environment, sometimes at considerable distance from their source.

Jan 1, 1991

By F. E. Heuze

This article deals with the effects of high-explosive and nuclear explosions in rock masses. We first highlight the strong influence of geological discontinuities, such as joints and faults, on ground motion characteristics. Then, we briefly introduce the Discrete Element Method, as a new technique for numerical simulations. II is shown to be far superior to continuum-based approaches, when dealing with the dynamics of discontinuous media such as jointed rocks. Finally, we simulate the ground effects from a generic contained nuclear explosion, which bears some similarity to the SHOAL event in granite. This calculation is intended to emphasize the influence of the near-source geology on the distribution of energy, and on the motion at various azimuths in the medium.

Jan 1, 1991

By W. R. McDonald

The U.S. Bureau of Mines investigated treatment of gold and silver refractory ores and concentrates that respond poorly to conventional cyanidation techniques due to the complex mineralogy of the ore. Three types of ores were investigated: gold locked placer sands, gold locked in sulfides, and gold that is robbed from the pregnant cyanide solutions by minerals in the ore. Ore treatment included grinding, flotation, cyanidation, air oxidation, pressure oxidation, hypochlorite oxidation, roasting, and carbon in leach.

Jan 1, 1991

By M. D. Strachan

Technical & Procurement Services Limited (TECHPRO) in Ashford, Kent, UK, have been appointed as Project Managers for the major rehabilitation of the Copper Smelting complex of Nkana Division, Zambia Consolidated Copper Mines Limited, (ZCCM) Zambia. In outline, the overall scope covers three main areas: a) Transfer and implementation of new technology into Zambia for the production of primary copper. b) Replacement of gas collection and gas treatment circuits to guarantee high quality feed to the acid plants. c) Completion of a number of minor projects in the copper smelter and associated utility plants to complement changes in the primary smelting technique. This paper describes the Project Management methodology and style used by TECHPRO to tackle typical problems that arise in retrofit projects of this type. Reference is made specific aspects of the smelter projects to illustrate solutions to the problems. The subjects. addressed highlight the complexities not only of having a -Client 5,000 miles from the Project Office, but also the difficulty of co-ordinating and controlling the performance of min sub-contractors who are also geographically distant.

Jan 1, 1991

The need for an integrated approach to optimization of unit operations in both the pit and the mill has long been recognized, but the complexity and nature of the overall problem has up to now resisted solution. This paper reports on a modeling methodology which couples symbolic and numeric computing to unify operations in both the pit and mill. The ultimate goal of this work is to optimize all operations that are influenced by blasting. Blasting plays a key role in all facets of operations. Obviously, drilling and blasting costs are determined by blast design, but the down-stream costs that are closely related to blasting results are often treated as separate functions: loading, hauling, cleanup, and crushing and grinding are all heavily influenced. Diggablilty and bucket fill factor are a function of fragmentation, the condition of the floor and uniformity in the shape of the muck pile. Likewise, cycle times and loading delays partially determine haul cycles, while fragmentation distribution and size determines the efficiency of truck loading. Removal and breakage of oversize causes loading delays and increases cleanup costs. The influence of blasting doesn't stop at the crusher. Mill productivity, power consumption, and maintenance are a function of the feed. Even at the SAG mill a reduction of a critical particle size during blasting can increase throughput. Thus, a bottle-neck for production far removed from unit operations in the pit can be alleviated by a modification in blast design. The question is: how do we optimize blasting with respect not only to itself but to al\ related mining and milling operations? For that matter, how do we even model blasting so that we can control the results of a blast?

Jan 1, 1991

By Q. Xu

Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied with sodium dodecylsulfate as the anionic surfactant and octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactant was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in wettability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant molecules at the interface.

Jan 1, 1991

By Annan Cook

J.R. Atkinson, office engineer to Kennecott Copper Corp., summarized data on the Mineral Park area [Wallapai (Chloride) Mining District, Mohave County, Arizona, Fig. 1] and submitted it to the New York office in 1950. He recommended an examination. Weston Bourret, a Kennecott geologist, accompanied by B.S. Butler, the well known former US Geological Survey geologist, examined the larger of two hydrothermally altered areas in Mineral Park that same year. Bourret recommended that the property be optioned and mapped. Georges Ordonez, Kennecott's chief geologist, after a field examination, agreed with Bourret's conclusions At the end of the summer of 1951, Annan Cook (another Kennecott geologist) accompanied Ordonez to the property prior to starting a mapping program. At Ithaca Peak, the structure, alteration, and reddish-brown coloring in leached cavities-hematite, jarosite, and goethite with minor copper staining - made an interesting target. The Peak, which has since been mined, was a Laramide quartz monzonite porphyry grading into quartz porphyry, penetrating Precambrian rocks. Turquoise had been mined from several workings on the Peak. Surrounding the central area of alteration, but mainly to the northwest, there were many long-abandoned underground workings mined for zinc, lead, gold, silver, and copper. To the west of Ithaca Peak within the main area of alteration, surface evidence of a chum drill hole suggested interest in the disseminated mineralization probably prior to World War II. A topographic and geologic survey of the altered Ithaca Peak area was initiated by Cook in September 1951. He was assisted by Richard Vosburgh, field engineer, and by four geologists: Charles Goddard, III, Donlon LoBionda, Keith Martin, and A.T. Stone. When Cook returned to New York, Vosburgh was left in charge. Mapping continued and diamond drilling took place during the winter of 1951-1952. Drill sites were selected entirely on the basis of surface geology. Five drill holes, including a flat hole, located around the flanks of Ithaca Peak, averaged about 183 m (600 ft) in length. A sixth hole caved at less than 60 m (200 ft). The best values obtained were in the first hole (-45°): 90 m (300 ft) averaged 0.62% copper and 103 m (337 ft) averaged 0.041% molybdenum. In another hole, 43 m (142 ft) averaged 1.09% copper and 0:023% molybdenum. The values of copper and molybdenum in these two holes were generally higher than in the remaining holes, although molybdenum values were always around 0.024% or better. The New York office decided, however, to abandon the project even though the remaining field crew of three had recommended more drilling.

Jan 1, 1991

Increase the productivity of domestic mining operations by improving the performance of rock drilling systems. Approach Investigate the use of chemical solutions at zero surface charge concentrations as drilling fluid additives to enhance penetration rates and extend bit life. Background Bureau researchers have investigated the use of chemical additives to enhance drilling performance and have found that the most efficient drilling occurred when the drilling fluid was able to maintain a zero surface charge (ZSC) on the rock surface. Laboratory drilling studies using 5/8-inch diameter diamond-impregnated coring bits on rock types such as quartzite, granite, taconite, and marble. Cationic compounds were used as the surface charge neutralizing additives during these tests. The drilling studies demonstrated enhanced drilling performance, however, only at the singular additive concentration that produced the ZSC condition. Bureau researchers made a breakthrough when they found that polyethylene oxide, although a nonionic polymer, was able to maintain the ZSC condition over a wide range of concentrations. Success using polyethylene oxide as the drilling fluid additive during subsequent laboratory tests prompted testing under field conditions.

Jan 1, 1991

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991

By H. Simpson

Middelburg mine is an opencast export mine operating in the Eastern Transvaal Coalfields of the Republic of South Africa (Figure 1). The mine was commissioned in 1983, to its original design capacity of 4.25 million sales tonnes which was subsequently raised to 5.5 million sales tonnes in 1989. This increase in export tonnage was brought about through an increase in the mines export allocation and the revision of management strategies. The maintenance of this increased tonnage with minimal additional capital has been achieved through improved operational efficiencies and the upgrading of planning operations through the purchase of an Enhanced Mine Scheduling Software Package (EMSSP/MINESTAR). Simultaneously with this requirement were additional factors that contributed to the implementation of the EMSSP. The mine was owned by a joint venture of two partners and is operated by Middelburg Mine services (Rand Mines Pty. Ltd) (Figure 2). This structure of ownership required the evaluation of numerous planning options to be under-taken concurrently and hence the need for an efficient streamlined scheduling pack-age that could fulfill this requirement. Compounding the EMSSP needs further, were the problems experienced in the export market, these being the external pressure from current and new suppliers in the market place which obliged management to provide solutions to rapidly changing market conditions. These fluctuating market conditions have had a direct effect upon the mine's planning strategies because of the large percentage of the mine?s sales sold on the international spot market. The sanction factor for all South African exporters has had a negative effect upon price and this was compounded further through internal competition in 1987 via suppliers attempting to maintain the market position.

Jan 1, 1991

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By G. H. Khoe

Neutralisation of acid uranium mill tailings with lime or other alkaline materials is usually practised to reduce the dissolved concentration of heavy metals and radio nuclides. Computer modelling of this process was carried out using the geochemical equilibrium code MINTEQA2. Computed dissolved metal and sulfate concentrations were compared with laboratory-based experimental data. It was found necessary to include the modelling of adsorption of trace metals (such as uranium and lead) by the precipitated ferric hydroxide in order to obtain acceptable concentrations in the neutralised liquors. There were limitations of the modelling exercise due to important aspects which were not addressed or properly accounted for such as chemical reaction kinetics and the effect of high ionic strength. These are discussed in the paper.

Jan 1, 1991

By T. H. Jeffers

The U.S. Bureau of Mines' Salt Lake City Research Center. has developed porous polymeric beads containing immobilized non-living biological materials for extracting metal contaminants? from wastewater&. Immobilized biological materials include peat moss, algae, biological polymers, and other materials that demonstrate high .affinities for heavy metals. The beads, designated as BIO-FIX beads, have distinct advantages over traditional methods of utilizing biological materials in that they have excellent handling characteristics . and can be used in conventional processing equipment or low-maintenance systems.. Toxic metals such as copper, cadmium, zinc, lead, and mercury are several of the many heavy metals effectively removed from mine wastewater& using B'IO"FIX beads. Continuous cyclic testing indicated that the beads continued to produce treated effluents which met National Drinking Water Standards (NDIJS) after 175 loading-elution cycles, Adsorbed metals were removed from the beads using dilute ?mineral .acids. In many cases" the extracted metals were further concentrated to enable processors to reclaim the metals, thus minimizing the generation of a hazardous sludge. Tests indicated that use of the beads in a low-maintenance system was particularly effective for treating remote acid mine drainage waters? and small toxic seeps from hardrock mining districts ..

Jan 1, 1991

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

The Misima open pit gold mine is a 20Mt per annum operation. Blasthole drilling is used to sample all material at a uniform 5m square pattern, and representative sub- sampling of the blast holes enables assay samples to be collected over the full 10m bench height. Samples are assayed for gold, silver and copper at the Company's laboratory at the mine site and the assays are provided to geologists as a written assay report and on floppy disc. Surveyed blasthole locations and assay results are transferred via personal computers (PCs) to a SUN mini-computer where results are stored by bench, blasthole assays are kriged, and plot files are created. A geologist selects grade boundaries from the kriged data, adjusting the boundaries towards the raw blasthole data where hard boundaries are recognised. Surveyors peg the resultant boundaries in the pit using a system of colour-coded pegs to display the different material types. A daily plan also shows boundaries and face positions.

Jan 1, 1991

By S. G. Britton

Microcomputer analysis has long been a technique for engineering professionals to improve the theoretical and practical design of continuous mining systems. Such work has been typically composed of modeling observed events and then introducing a variety of known elements with predicted results to compare against the results of the model. Programs written in BASIC, Cobol, Fortran, or other language dominated such efforts. These programs have taken years to develop and prove out. This paper explores a new management tool used at TMC on a daily basis to track and improve continuous mining systems through the use of microcomputers and Lotus 1-2-3 software. By analyzing data provided by section foreman, shift foreman, and maintenance personnel against predetermined goals, new production targets are developed, weaknesses in the current mining systems are identified, and the results of changes are measured. The results of this system on the productive output of TMC systems are on the order of ten percent improvement.

Jan 1, 1991

Dynamic permeability is a significant hydrologic condition associated with in-situ leaching at the Cyprus Casa Grande operations. Several factors contribute to changes in the permeability conditions. They are: 1) hydraulically induced fracture development, 2) geochemical changes during leaching in the rock matrix, and 3) changes in the relative degree of saturation of the deposit. Dynamic permeability conditions were evaluated using available pressure and flow rates from the 58 injection and recovery wells obtained over one year period. A finite element, 2-D hydrologic model called INVERT which is designed to estimate aquifer parameters under transient and steady state flow conditions was used for the investigation. The permeability conditions during 7 different steady state intervals throughout the one year time frame were determined. The results confirm that big changes in permeability occur as a function of time as well as a function of injection pressure condition.

Jan 1, 1991

By J. F. T. Agapito

Significant economic benefits can result when rock mechanics is applied within a practical framework and integrated within the other engineering functions of the mine organization. Such application and integration requires management support and understanding of rock mechanics as a practical tool to help attain high standards of safety, productivity and resource recovery. For such an approach, a long-term geotechnical program is needed in most operations to build an adequate data base and to ensure that design and ground control issues are handled in a cost-effective manner. Best usage of rock mechanics in mining occurs when management recognizes the application as a long-term investment, where time is needed to realize good returns. The need for this approach is due to the difficulty in accurately predicting ground conditions ahead of mining. The practical application of rock mechanics must follow an iterative process of design and verification based on site-specific experience to account for geologic and mining impacts. Ground conditions experienced during mining must be used to check the initial mine design and, if necessary, to provide a basis for design modification. Such a practical rock mechanics program includes comparative experience, in situ instrumentation and numerical modeling. The program begins with the geologic site investigation and continues throughout the life of the mine. It is an integral part of mine planning and operation.

Jan 1, 1991

By Edward L. McHugh

Mineral resources in the Silver Creek study area of the Nez Perce National Forest. Idaho, were investigated during the summer Of 1989. The study area includes the 36,100-acre Silver Creek-Pilot Knob RARE II area (No. 1-849) on the north side of the South Fork Clearwater River, about 11 miles west of Elk City, 10. Mines in and near the study area in the Tenmile and Newsome mining districts produced about 100.000 02 of gold, mostly from placers. Gold production had an historic value estimated at 52 million, equivalent to nearly $40 million at today's prices. Lode mines produced about 19,000 oz of gold, along with smaller amounts of silver, copper, lead, and zinc. Of 34 mines and prospects examined, ten lode properties are considered to be significant by virtue of their past development or production and the presence of possibly ore-grade mineralization. There are no identified mineral resources in the study area; however, samples that contained gold and anomalous arsenic delineate a three-mile-long area from the Sentinel mine, north to the Blue Quartz prospect where exploration might disclose resources. One mining company is conducting geophysical studies and drilling within the delineated area. In addition, six placer sites may contain enough gold to be of possible interest for future exploration and development.

Jan 1, 1991