Search Documents

By Kunihiko Takahashi, Gjergj Dodbiba, Hisayoshi Umeda, Toyohisa Fujita

"An increasing number of mobile phones is increasing the number of the discarded mobile phones. Many efforts are thus being made to collect and recycle these devices. This paper is a short introduction of the recycling system of precious metals from the discarded mobile phone, currently available in Japan. Moreover, an attempt has been made to compare the energy recovery and the mechanical recycling of plastic wastes from the discarded mobile phone. The assessment has been carried out in the context of the life cycle assessment methodology (LCA). The environmental impact of each option was assessed by calculating the following impact indicators: depletion of abiotic resources (ADP), and global warming potential (GWP). 1. Introduction In 2003, the demand for mobile phones was increased since the camera was included in a mobile phone and the 3rd generation of mobile phones was introduced. In turn, the number of discarded mobile phone is rising sharply. Generally speaking, all the metallic parts of mobile phones can be recovered and recycled by using smelting and purification techniques. The recycled materials are then used to fabricate other new products."

Jan 1, 2008

By Tomoya Nihei, Hiroshi Hayashi

"A novel selenium removal process called Recycled Green rust/Ferrite Process is developed by MMC. In this process, a mixed Fe2+-Fe3+ hydroxide compound, green rust (GR), reduces selenate to elemental selenium, while GR is consequently oxidized to magnetite Fe3O4. Sequencing batch-mode experiment showed that the residual selenium concentration gradually decreased with the number of batch test increased. Stable selenium removal was achieved when the number of batch test exceed 15 times. Optimum selenium removal ratio reached 99.95% where initial Se concentration 2.1mg/L decreased to 0.001mg/L. Furthermore, the continuous feeding test carried out through a pilot-scale plant with a feeding capacity 600 L/hr. Approximately 860-hour-feeding test was carried out for the selenium-contaminated groundwater which had an averaged selenium concentration of 0.88 mg/L. Selenium concentration in the effluent from thickener maintained less than 0.01 mg/L (selenium removal rate of 99%) until a net operating time reached 800 hours.IntroductionJapan is one of the largest producers of selenium, and thus there are potential environmental impacts of selenium on soil and aquatic environments. The Mitsubishi Material Corporation (MMC) owns some real estate properties whose soil and groundwater was polluted by selenium and other heavy metals. These sites include former industrial plants: a smelter for nonferrous metal and a fabricating semiconductors and pigments. Selenium in aquatic environment commonly exists in four oxidation states, namely, VI, IV, 0 and -II. Selenate ion (SeO4 2-), the most oxidized form of selenium, and selenite ion (SeO3 2-) are highly soluble and mobile. Elemental selenium (Se0) is insoluble in water and therefore has much lower toxicity. Because selenium is carcinogenic and teratogenic at high concentration, the national effluent standard in Japan is fixed at 0.1 mg/L and the environmental standard at 0.01 mg/L. Although there are several selenium removal techniques, the most conventional process is coprecipitation with a ferric hydroxide because of its simplicity and low cost. It is known that selenite is adsorbed strongly on the surface of ferric hydroxide, but selenate is not. The low affinity of selenate on oxide mineral surfaces was demonstrated by the fact that selenate could be easily displaced by adding competing anions, particularly sulfate ion. Selenate removal from polluted water is one of the most difficult techniques, and more effective methods are desired. MMC developed a novel selenium removal process [1]. In this process, the concentrated slurry that contains Fe(II)-Fe(III) hydroxyl-salts known as Green Rusts (GRs) contributes to selenate removal. The main components of the iron precipitate in the reactor are GRs and their oxidation product, magnetite (Fe3O4)."

Jan 1, 2008

By Qingzhu Li

The adsorption process of Pb2+ from aqueous solutions by spent grains modified with Imol/L NaCI solution was investigated. The effects of solution pH, contact time, adsorbent concentration, initial Pb2+ concentration, particle size on Pb2+removal were also studied. The initial adsorption process was rapid and 90.35% of Pb2+ adsorption occurred within 30 min. The absorption equilibrium was obtained at 4h. When pH was 5.5, Pb2+ concentration in aqueous solutions decreased from the initial content of 20 mg/L to 0.0 I mg/L after 5 hours by application of IOg/L adsorbent at 25?C, Pb2+ removal efficiency reached up to 99.95% and the Pb2+ remaining in aqueous solutions was under China Sanitary Standard for Drinking Water (GB5749-85). Adsorption data fitted well with Lanf+muir and Freundlich models. However,Langmuir isotherm model was better to descnbe Pb- adsorplion than Freundhch model, mdlcatmg that the applicability of monolayer coverage of Pb2+ on the surface of adsorbent.

Jan 1, 2008

The emerging discipline of ægeometallurgyÆ is not new but is becoming increasingly recognised as a discrete and high-value activity that reflects an ongoing commercial and cultural trend towards more effective mine site integration and optimisation. The AMIRA International P843 æGeMIIIÆ project (Geometallurgical Mapping and Mine Modelling) is a major new cross discipline research collaboration designed to provide support for this emerging industry trend. The project is currently supported by 18 global mineral companies and involves collaboration between the CODES Centre of Excellence (University of Tasmania), JKMRC and BRC (University of Queensland) and CSIRO Exploration and Mining. These groups represent recognised research excellence in the fields of economic geology, automated core logging, advanced microscopy and process mineralogy, mineral processing, mine planning and resource optimisation. The needs and challenges of geometallurgy as an integrated activity will be outlined together with the ongoing contribution and aims of the AMIRA P843 æGeMIIIÆ project. The main emphasis is on development of predictive geometallurgical indices for key processing performance parameters that reflect inherent geological variability. The ultimate aim is to provide predictive indices of geometallurgical performance that can be confidently embedded into resource models and used for risk-defined mine planning and optimisation.

Jan 1, 2008

By Takashi Sasaoka

The PT. Adaro Coal Mine targeted in this research is located in South Kalimantan, Indonesia. The coal production of this mine is increasing year, with about 35 M tons of coal produced in 2006. This mine faces many ground control problems, especially instability of the footwall. Large-scale landslides occur often in the footwall; this may be because of weak rock and the effect of footwall rock weathering. Hence, prompt measures must be developed and followed in order to preserve the stability of the footwall and make this mine safe. Additionally, the final pit design is now being reconsidered because of the increasing demand for and high price of coal. With these issues in mind, this paper describes a solution for improving the stability of the footwall and discusses the final pit design based on the results of an on-site investigation and numerical analysis.

Jan 1, 2008

By Rudiger Baltz

The sudden failure of bodies of rock is a serious problem commonly experienced in the international mining industry. These explosive releases of energy are referred-to as ?bumps?, ?outbursts? and ?rockbursts?. Rockbursts can occur at such a rapid speed that they present a direct threat to safety in large parts of the mine workings. The build-up of excess stress within the body of rock can be attributed to different causes. In shallow workings, for example, sudden and violent failure of the roof strata can be caused by leaving insufficient pillar width when practising room-and-pillar mining. At much greater working depths, as it is the case in the German coal industry, rockbursts are generally attributable to high levels of rock pressure. This can even result in coal outbursts when driving individual roadways. More than thirty years ago the German coal industry suffered from numerous rockburst incidents which caused many deaths and serious injuries. This led directly to the establishment of the Rockburst Prevention Centre, which was created at the instigation of the mining companies and the chief mines inspectorate. The consistent logging and analysis of all rockburst incidents has led to the development of a system that is still used as a basis for preventing underground rockbursts and minimising the risk of such phenomena occurring. Working closely with the mining authorities and mining companies the accredited experts of the Rockburst Prevention Centre have played a key role in helping to develop and implement a range of methods for the early detection and prevention of rockbursts.

Jan 1, 2008

By F. Nava-Alonso, O. Alonso-González, A. Uribe-Salas, R. Pérez-Garibay

"Cyanidation is the most used method to recover gold and silver from their ores. In this process, other metals besides gold and silver may sometimes dissolve and interfere with the efficiency of extraction. Copper is one of those metals, reaching concentrations as high as 1000 mg/L in some cyanidation plants, making difficult the extraction and purification processes, and increasing the operating costs.This preliminary work was intended to study the feasibility of using amines to form a precipitate and to eliminate copper from a synthetic solution containing high copper and cyanide concentrations, as is the case of some cyanidation effluents. The solid formed is removed from the solution using conventional filtration techniques. Seven amines were evaluated at different pH values and amine additions. Up to 90% of copper present may be removed at the natural pH of the effluent (alkaline). The remaining copper would permit to recycle the solution back to the cyanidation process. IntroductionCopper is generally considered the most problematic metal in gold leaching due to the rapid formation of copper cyanide complexes when some readily-soluble minerals are processed (e.g., azurite, malaquite, cuprite, chalcocite and bornite). The copper solubilization as cuprous cyanide complexes leads to a significant economic penalty in terms of excessive cyanide consumption and high cost for cyanide elimination. When activated carbon is used to recover gold and silver, the copper-cyanide complexes decrease the efficiency of the process because of the competition of the cuprocyanides with the aurocyanide for the adsorptive sites on the activated carbon (Rees and Deventer, 1999).Several techniques have been developed to attempt to overcome the problems caused by the copper presence in cyanidation solutions, notably: acidification-volatilization-regeneration (AVR), ion exchange-electrolysis or solvent extraction-electrowinning (Lu et al., 2002). In this work the use of some amines is proposed to remove the copper-cyanide complexes by precipitation of a copper-cyanide-amine solid. The process was evaluated for different amine additions and pH values, using copper-cyanide synthetic solutions of composition similar to that presented by some cyanidation plants with high copper."

Jan 1, 2008

By B. Grinbaum, A. Mazuelos, F. Carranza, N. Iglesias, M. Avila, J. L. Lozano, G. Perez, R. Romero, M. \/aliente

Following a failure of a tailings pond darn at a mine in Andalusia, Spain, a huge effluent stream, that contained about 1 g/1 Zn and significant amounts of ferrous, ferric, calcium, copper, aluminium and manganese cations has to be treated, to prevent pollution of a nature reserve. EGMASA, as the regional government environmental agency, suggested to improve the current depuration process by recovery of the Zn from the effluent. A solvent extraction (SX) followed by electrowinning (EW) was proposed and developed to remove zinc.. A pre-treatment stage consisting in bio-oxidation of ferrous iron by using a bacterial process followed by an alkaline precipitation was employed because iron in the effluent is incompatible with both the SX and the EW processes. The SX process was developed successfully at the laboratory scale and verified in a pilot plant on-site, using two Bateman Pulsed Columns for extraction and stripping of zinc. The results were satisfactory obtaining a recovery of 90% of Zn. The process was suitable for industrial application.

Jan 1, 2008

By Enrique Posada

"The Valle de Aburrá area, corresponds to the city of Medellín and neighboring municipalities, with more than 3 million people. The area generates a sizable amount of solid waste, which has been taken to landfills for the last 20 years. This paper proposes a model for public policy making which considers the cost and benefit of different alternatives to handle the wastes in the coming 20 years. Combinations of several alternatives: Recycling, waste reduction, waste separation, incineration, land filling with lixiviate treating and gas energy recovery, and organic waste composting are considered and modeled and the results presented as a contribution for a more rational approach to policy making than the one currently being employed.IntroductionThe author, working for INDISA S.A., acted as a consultant for the direction of planning of the Empresas Varias de Medellín in 2004. This entity has the responsibility for the handling of the solid wastes of the city of Medellín and some of the neighboring municipalities. At the present time more the 700.000 annual tons of waste are taken to the site of La Pradera, located in very rainy location (3.000 mm of precipitation per year), with complex in topography and very far away from the sources of the waste. During the work the author detected important problems that should be addressed, as follows:Lack of adequate technical administration and resources. The entity did not count with sufficient human resources to focus on the appropriate technical handling of the solid waste. The organization worked mostly with independent contractors, lacking enough coherence and integration. The internal workload was too large for the few people who had technical responsibility and this gave rise to attention problems. It is important to have clear technical procedures, technical know how and human resources, continuity in the activities. It is important to have a clear capacity to plan, to study, to make tests and monitoring, to pursuit and develop ideas, to optimize the processes and to introduce changes, to respond to environmental authorities, to the communities and to mass media and to handle the contractors. All this was basically lacking. In the case of the handling of the sanitary filling of La Pradera, for example, although the people in charge were very able and dedicated, the magnitude of the task was too large and the resources they had were insufficient. As a result, the site had at the time of the study, problems with thousands of vultures, lack of immediate cover up for the waste, uncontrolled leaching, the area being dirty and little attractive, despite being called a park."

Jan 1, 2008

By A Roshal

It is anticipated that many future uranium mines in Australia will be using the in situ leaching mining process. It is fair to say that close to one third of uranium production will be generated by this method, whilst the other two thirds will fall on the uranium generated from hard rock mining and other mining methods, such as traditional open cut mining. For other types of deposits the in situ leaching mining method will remain the best technological, commercial and environmental alternative. It is important to identify and prevent all risks involved in uranium mining. The expertise in this subject is limited. Over the years there was only one mine using the in situ leaching process for uranium extraction in Australia. Computer simulation of propagation of leachate during and after the uranium in situ leaching is a crucial factor, not only for addressing the environmental concerns, but also for the most efficient recovery of the deposit. The decontamination can be modelled for a period of up to 100 years, with the acid neutralisation forecast for a period of up to 400 years. The results of the modelling are paramount for definition of the reserves, efficiency of the mining method and the environmental impact statement. The accuracy of the hydrogeological modelling and carefully selected environmental management program enables a mining company to quantify and minimise the impact of the mining activities on the regional aquifer and to prevent environmental disasters. In the study, the completed hydrogeological model allowed the client, the authorities and the community to make an informed decision about the environmental impact of the in situ leaching of uranium. In particular, the model proved that neither during the mining, nor during the neutralisation the toxic elements would interact with the local catchment area.

Jan 1, 2008

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Paul Downing

A typical day for a blasting company includes what seems to be an infinite list of tasks dealing with numbers. Whether determining the exact amount of explosives material in inventory, the number of holes in the shot, the exact distance from the blast site to the nearest exposure, or the capacity of bulk hoppers, the accuracy of numbers is key to ensuring the safety of the public, property and personnel.

Jan 1, 2008

By G Booth

Whilst communications systems in the mining industry have evolved over the years, the premise remains consistent that reliable communication is vital for safety and operational efficiency. TodayÆs open pit mines are benefiting from advanced developmental efforts based on mesh networking hardware and software technology. This paper highlights Rajant CorporationÆs adaptation of technology, originally developed for the defence and first responder industries, to provide wireless network connectivity in open pit mining applications. Featured is the large-scale deployment of over 300 mobile, meshing access points in the Bingham Canyon Copper mine near Salt Lake City, Utah, the worldÆs largest open pit copper mine. Many companies have positioned themselves, their technology and their product line in the arena of rugged outdoor wireless broadband mesh networking infrastructure. However, Rajant Corporation has combined specialised command and control software and portable networks which offer network extensibility and redundancy that are not available in any other networking solution. Rajant CorporationÆs BreadCrumb« offers unique traits in portability and non-line-of-site networking nodes which intelligently route and broadcast in standard 802.11 protocol. The advantage of RajantÆs solution is especially valuable for users needing equipment moved easily and rapidly into and out of the theatre of operations with uninterrupted network availability. The main differentiators that set the BreadCrumb« network apart from the competitors are mobility (continuous availability), simplicity, ability to properly load balance and power options. In 2007, RajantÆs BreadCrumb« wireless mesh system was selected by the Kennecott Utah Copper Corporation (KUCC), a wholly owned subsidiary of Rio Tinto, as its primary communications platform for operations within the Bingham Canyon Copper mine, the worldÆs largest open pit copper mine. The Rajant BreadCrumb« technology enables KUCC to gain additional operational efficiencies by tracking, monitoring and managing its copper mining operations. The primary goal of using the BreadCrumb« wireless mesh system Kennecott was to streamline its complex mining operations. KUCC required a high number of moving wireless nodes for improving mine monitoring and control. The Rajant InstaMesh« software running on the wireless BreadCrumb« units connects hundreds of devices to each other while rapidly transporting critical operational data. Kennecott has successfully implemented a large number of BreadCrumb« radios in an interconnected network that allows loader trucks, shovels, pumps, laptops and other production equipment to communicate with each other in real-time. These systems are a mix of secure access nodes that enable data and voice communications across a meshed, self-healing network for fleet dispatch, health monitoring and other critical mining applications. Many of the devices that require wireless communications are moving at all times throughout the wireless mining infrastructure. The BreadCrumb« nodes rapidly adapt to any changes in the network topology, assuring that IP traffic uptime and bandwidth are maximised. The installation layout and data network specifics, as well as maps and data network efficiencies will be detailed in the paper.

Jan 1, 2008

By Magdelinka Padenkova-Yaneva, Emilia Christova Kostakeva

"Environmental protection is becoming over the years an increasingly significant problem of mankind. Up to the last decade the only way to make the domestic waste harmless in Bulgaria was deposition on uncontrolled landfills without undertaking actions for protection of the soils. This also caused pollution to spread into the surface and underground waters and that is why actions are now undertaken for remediation of contaminated soils. This is achieved by developing projects for the closing down of polluted sites. In the present paper some projects for closing down of polluted areas are discussed. The actual conditions are examined and project decisions for preventing the surface waters from penetrating into the waste are presented. In this way the pollution of the soil is stopped and the soils are gradually remediate.IntroductionSoil is the topmost layer of the earth crust. It consists of mineral particles, organic substances, water, air and living organisms and is an extremely complex and changing living environment. Soil is a non-renewable natural resource which is of considerable importance in a number of crucial processes (production of foods, storing, filtrating and turnover of many substances, including water, carbon and nitrogen). It also serves as a basis for human activities, shaping the landscape, ground on which cultural heritage is built, and source of raw materials. These functions of soil must be protected both because of their social and economic significance and from the point of view of environmental protection.The processes of erosion, loss of organic substances, compaction, salination and contamination contribute to the degrading of soils accompanied by a negative impact on human health, natural ecosystems and changes in climate, as well as on the economy. All these make it necessary to protect soils from contamination. Over the last years intensive work started in Bulgaria for the construction of controlled sanitary landfills for rendering municipal solid waste harmless. Pursuant to Bulgarian legislation, in these controlled sanitary landfills measures are undertaken for protecting the soils from contamination through appropriate project decisions – the filtration of the products from the biological decomposition of waste into the adjacent sites (soils) and, therefore, the contamination of the surface and underground waters is prevented. At the same time the purity of air is maintained, human health is protected and conditions are created for including the controlled sanitary landfills into the surrounding landscape."

Jan 1, 2008

By George Burnhart

"Sonic drilling is a relatively new technology even though it has been in development since the late 1940s. It was initially funded by the U.S. petroleum industry and then, in the late 40s, Russian scientists worked on developing sonic drilling, their interest based on drilling rates 3 to 20 times that of conventional methods. In the early 1960s, the Shell Oil Company backed research that resulted in a down-hole device with a series of eccentric weights driven by drilling fluid to generate vibration. Hawker Sidley, in the early 1980s, developed the first modern prototype sonic drills in Vancouver B.C. and the North Star Drilling Company in Minnesota became the first contractor in the U.S. to operate sonic equipment in 1985. In 1994, North Star became a division of Boart Longyear, headquartered in Salt Lake City, Utah.What’s Unique about a Sonic DrillA sonic drill rig appears and operates very much like any conventional top-drive rotary rig. The key difference is that a sonic drill has a specially designed hydraulically powered drill head, containing oscillators, that generates adjustable high-frequency vibratory forces. The sonic head is attached directly to the drill pipe or outer casing, sending the high frequency vibrations down through the drill steel to the face of the drill bit. This creates displacement, fracturing or shearing action depending on the material being drilled. The oscillator uses two eccentric, counter-rotating balance weights or rollers that are timed to direct 100% of the vibration at 0 degrees and 180 degrees. An air spring houses the oscillators and separates the vibration from the drill rig itself. The vibratory frequency is controlled to suit operating conditions and to achieve optimum drilling rates.When the vibrations coincide with the natural resonant frequency of the steel drill rod or casing, a natural phenomenon called “resonance” occurs. It allows the rig to transfer timed vibratory energy into the top of the drill string, utilizing the natural stored energy of the steel. This causes the drill string to use inertia and act like a flywheel delivering tremendous amounts of energy directly to the bit face. In friendly overburden formations, a sonic drill rig can achieve penetration rates of one ft per second."

Jan 1, 2008

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By Lee Fergusson

"The primary features of ViroMine™ Technology are introduced and applications of ViroMine™ Technology to mine site remediation and the treatment of a variety of intractable waste-streams, including a technical discussion of acid neutralizing capacity, metals binding capacity and longterm stability of results. Outcomes from four applications at high-profile international mine sites are presented: 1) the superfund site at the Gilt Edge Mine, South Dakota, USA (four years of data on the treatment of acidity, TDS and metals such as Al, Co, Fe, Mn and Zn); 2) one of Australia’s most polluted sites at King River Delta in Tasmania (treatment of TAA and TPA, and metal and metalloid contaminants such as As, Cr and Hg); 3) The Aljustrel “Aqua Forte” mine site in Portugal (high acidity, metal and metalloid contaminants such as Al, As, Cu and Zn) and 4) the Ulsan Iron Ore Mine at Ulsan, South Korea (treatment of metal and metalloid contaminants such as As, Cd and Ni).IntroductionThe commercialisation of ViroMine™ Technology has resolved some of the most intractable pollution issues associated with historic mining ventures on a global scale and has facilitated the neutralisation of Acid Rock Drainage (ARD), remediation of acidic and metal contaminated impoundments (including tailings dams) and promoted revegetation on tailings deposits and waste rock dumps. ViroMine™ Technology also enables current mining ventures to manage effluent simply and efficiently to meet increasingly stringent environmental standards and is enabling the mining sector to reconceptualise the management of mine spoil. The abilities of ViroMine™ reagents to neutralise the actual and potential acidity of sulphidic mine spoil coupled with the ability to bind metal and metalloid contaminants into non-bio-available forms are the key features delivering environmental and economic benefits to the mining sector and the broader community. Results from four projects utilising ViroMine™ Technology are presented to highlight the suitability of ViroMine™ Technology to treat all forms sulphidic mining wastes. 37"

Jan 1, 2008

By E. Koufetzis

Rock mass classification systems are core elements of tunneling and empirical mine design worldwide. The Bauxite division of S&B Industrial Minerals S.A. decided to implement a rock mass classification system in order to provide mining engineers and supervisors of the underground mines, with guidelines of stability performance and with a complementary tool for the selection of the appropriate tunnel support. The back analysis system employed is based on visual observation of especially selected underground mine sites, representative of all rock types. This fact combined with the failure or success of the already existing support system, constitute the fundamental part of the work undertaken. The paper is divided into three main parts. In the first part the classification methods of Q, RMR89 and GSI are presented and the advantages and disadvantages of each method in connection with underground mining are indicated. RMR89 and GSI are conclusively selected for use, the main criteria for the selection being, the simplicity in use and the competency of the support system suggested for each rock mass category. The second part points out the methodology for measurements, the practical difficulties encountered during this process and the guiding principles followed, in order to avoid these problems. In the third part, the final conclusion of this project is demonstrated and the different rock mass categories are presented with their relative support recommendations, as they were applied and tested in all phases of the bauxite mines? exploitation. The generated methodology is being implemented by the site mining engineers, for validation and potential improvement.

Jan 1, 2008

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008

By L. Becze, B. Pierre, S. Di Carlo, G. P. Demopoulos

From January to June 2007, the autoclave production at the Kidd Metallurgical Site was severely affected as a result of plugged discharge lines and extensive precipitation/crystallization of sulphates that caused massive scaling in different autoclave compartments. Work was performed at McGill University to understand the root causes. The crystallization of zinc and ferrous sulphate salts was investigated in terms of solubility measurements. Scale samples were characterized using chemical and mineralogical-spectroscopic analysis. In this paper, following a description of the Kidd zinc pressure leach operation, highlights from this investigation are presented and solutions used to overcome the problem are outlined.

Jan 1, 2008