Search Documents

By William C. Hood

A leaching column technique that produces effluent similar in quality to coal mine drainage in the Eastern Interior Basin has been developed. The columns are charged with 1000 grams of crushed overburden and cycled through the leaching process once a week for twelve weeks. Inter-relationships among the important chemical constituents are very similar to those present in actual mine drainage waters, but the overall concentrations of ion are more dilute in the leachates. Multiplying the leachate concentrations by a factor of 4.5 gives values similar to mine waters. Available data suggests that each of the leaching cycles represents about three years of natural weathering, so that the leaching technique can predict the evolution of the mire drainage water over a time span of nearly 40 years. Use of the leaching technique with drill core samples should provide a method of approximating mine drainage quality in advance of mining and should be quite useful in identifying potentially toxic units in the overburden. However, the results should he considered to be a 'worst case' situation because the technique' does not consider the effects of reclamation.

Jan 1, 1984

By Thomas O. Llewellyn

This U.S. Bureau of Mines (US8M) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material balance for the year 1989.

Jan 1, 1992

By Robert Lundquist

REAM is a unique method of rock breaking using high energy projectile impact. This report-describes the most recent in a series of tests demonstrating mining applications for the REAM method. In an underground limestone mine at Greer, West Virginia, REAM was used to drive a short tunnel and drill a large diameter borehole. Along with breakage data from these tests the goal of the program was to examine environmental problems which might result from the use of cannons under-ground. A total of 103 shots was used to advance a 14-l/2-feet high by 10-feet-wide face a distance of 5-1/2 feet. It is estimated that the 9.3-pound-concrete projectiles launched at 5000 feet per second will break an average of 0.78 tons of limestone or 67 percent of the 1.125 tons of granodiorite broken in previous tests. The 9-inch-diameter borehole was drilled horizontally by repeated axial impact for 7 feet, 2-1/2 inches by 21 shots giving an average of 4.12 inches per shot. Scaling this result to compressible impact energy yields an estimated 5.8 inches per shot for a 12.8-inch-diameter hole compared to 8 inches per ~hot for a 16-inch-diameter hole in granodiorite. Noise measurements indicate that a silenced cannon can be used within a few hundred feet of mine personnel in a room and pillar mine within the legal limit of 140 dB impulse without additional protection. Some fume measurements were made with satisfactory results, even though the military propellants used produce much greater quantities of toxic fumes than the liquid propellant proposed for the future.

Jan 1, 1976

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977

By Jean J. Tancous

Chromium recovery from wet-blue offal trimmings and shavings can be done with substantial chemical cost gains by incineration at 600° C for 5 hr. Pretreating the offal with 0.5 M Na2C03 and air-drying prior to incineration produce Cr04 .By simply incinerating the offal, without pretreatment, an ash containing water insoluble Cr203 was produced. The Cr203 in the ash was purified by leaching with water. Chromium and crude protein were efficiently extracted from offal using 5 pct Na103, 5 pct H2S04, and 3 pct NaCl at 40° C. This procedure was effective but expensive. Satisfactory leather as to odor, appearance and shrinkage temperature was made from chromium recovered from wet-blue offal by incineration and by extraction. Chromium conservation is possible by recycling chromium liquors and by precipitating chromium from spent tanning liquors prior to combining these liquors with other tannery wastes. Combining chromium liquors with other wastes introduces contaminants that make chromium recovery and reuse difficult. Leaching sludges with H2SO4 produced marginal chemical cost gains. Leather tanned with these solutions had satisfactory shrinkage temperature but the sludge odors and iron contamination were objectionable.

Jan 1, 1979

By W. L. Cooley

Electrical accidents occurring in coal mines from 1975 through 1979 were categorized and analyzed. The data was searched for common electrical hazards, common activities on the part of those injured, and common negligent or careless behavior. The most common electrical hazard was abnormal arcs or sparks, the most common injured activity was handling energized trailing cables, and the most common careless behavior was failure to de-energize circuits before working on them. The accident data was combined with mine production statistics to form a normalized electrical accident rate. It was found that some mines have consistently more lost workdays per man-hour worked than do other mines. Bureau of Mines electrical safety research contract expenditures were reviewed to judge whether the research effort was directed to those areas which are related to the most accidents. In some cases it was not. A method was devised and utilized to estimate the relative cost to the mining industry to implement certain safety measures developed through Bureau research, and also to estimate the potential safety benefits. Some safety changes are recommended, others are not. MSHA regulations were reviewed for effectiveness in preventing electrical accidents, and suggestions were made for discontinuing, clarifying, or otherwise modifying the regulations.

Jan 1, 1981

By Harry E. Brownlow

The United States Bureau of Mines contracted Norecol to prepare a report identifying the regulatory processes associated with metal mine development in British Columbia using the Snip Mine as a case study. The intent of this study is to assist industry and regulatory agencies in developing understanding as to differences in objectives, perspectives and operating methods. The case study will be incorporated into a larger report summarizing the comparative advantages and disadvantages of metal mine permitting in British Columbia and Alaska. The purpose of the report is to identify the development schedule and permitting process at Snip which will assist the U.S. Bureau of Mines in suggesting improvements in environmental review and permitting processes for mine developments. The report provides an abstract of the environmental assessment review processes in Canada and the Mine Development Review Process in British Columbia and provides an understanding of the linkages between policy, legislation, and environmental review.

Jan 1, 1992

By Robert L. Lagace

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal minus. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to determine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m2 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to he attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977

By Felix du Breuil

Contract H0177044 included three objectives; (1) consolidate, maintain, and distribute information on STE approved lighting systems; (2) develop and present one-day seminars on underground mine lighting; (3) determine direct labor and hardware costs associated with the installation of mine illumination systems. All objectives were completed with results as follows: Task I - A file containing 1350 Statements of Test and Evaluation (STE) for all types of underground equipment was developed and publicized throughout the coal fields, A total of 40 requests for STE information was received and processed. Task II and III - A series of 50 seminars was scheduled and presented to 942 attendees throughout the coal fields. The seminars were well received and attendees indicated the information presented would be helpful in bringing their equipment into compliance. Holding a series of seminars in the coal fields, instead of a few in population centers, was favored by attendees. Task IV - Installation cost data obtained on 415 lighting systems indicate that the factors which most affect installation costs are higher hardware cost for DC powered systems and slightly higher manpower requirements for systems installed underground. Based on these data, the total cost to industry of retrofitting existing underground equipment could range up to $50 million.

Jan 1, 1979

By D. V. Gaffney

This report presents the results of a three-phase investigation of the feasibility of using cemented coal waste in active underground coal mines to prevent mine subsidence. Coal caste was broadly defines to include waste from both coal preparation plants and coal-fired power plants. Underground systems with potential for cemented backfill are determined through identification of current mining methods and available technologies for cemented backfilling and consideration of materials and systems constraints upon mining and backfilling integration technical concerns including operation, health and safety, materials utilization, environmental impact, applicability and techni¬cal status are assessed for six (6) systems which were identified as potentially feasible. Two (2) of these systems are conceptualized in a hypothetical case history and developed to further assess their operational and economic feasibility. Comparisons of costs among both systems and with costs of surface disposal are presented. Also presented are the conclusions reached concerning the present feasibility of using cemented backfill in active coal mines and potential avenues for further research. Appendices contain further consideration for design of cemented mixtures to be used in backfilling, the results of laboratory testing of mixtures rich varying concentrations c: waste products and cementing agents, and an annealed bibliography

Jan 1, 1981

By Richard I. Barnhisel

At the Sinclair Study Site it was found that the deeper the soil the greater the yield of corn, soybeans, wheat, alfalfa, and timothy. Yields at this location were generally lower than those at the Alston Surface Mine. At Alston the non-prime land treatments generally produced greater yields for all crops than did the prime farmland treatments, however, the intermediate soil thickness, 20 cm topsoil over 40 cm of subsoil, gave the best yields, provided it's subsoil had been limed. From a chemical point of view, acidic spoils do not need to be buried by 120 cm or 4 feet of soil, provided adequate lime is applied to these spoils as a barrier prior to placement of good quality topsoil and only forage crops are to be grown. The burial depth must be increased to as much as 75 cm when grain crops such as corn or soybeans are to be grown. This response to burial depth appears to be related to water storage needed by the crop and not due to toxic effects of the spoils. A conventional farm tractor-mounted subsoiler increased yields of soybeans and corn the first one or two years, but the effect was diminished with time. Subsoiling did not produce significant increases for alfalfa or wheat. However, ripping with a bulldozer produced significant yield responses, especially for corn and soybeans, that have lasted for at least three years. The ripping effectively reduced the bulk density at least within the zones through which the ripper had passed. Liming the upper 20 cm of subsoil significantly increased yields of alfalfa, corn, and soybeans. There also appeared to be an interaction between this lime treatment and soil depth. Yields of some grain and forage crops may be high enough to meet target levels for bond release for prime farmland. Based on the present study, one should not expect corn yields to be high enough to meet bond release. This statement should not be considered final since the experiment is not complete.

Jan 1, 1983

By Burton Scott

A device for detecting carbon monoxide at ppm levels is described which is based on the measurement of infrared absorption at 4.65 microns. The unique feature of the nondispersive infrared instrument is contained in the optical design which includes a confocal cavity, increasing the effective optical path length by a large factor, thus greatly reducing the required package size. The cavity has the effect of reducing the total amount of radiation passing to the detector, but at the same time increasing the percent attenuation observed when adding CO, by a factor called gain. The radiation is chopped by a filter wheel which contains narrow band filters at 4.0 and 4.65 microns. The resultant signal produced by the pyroelectric detector is demodulated by the electronics to product an automatic gain control signal, proportional to the total radiation, and a difference signal, proportional to the CO present. Tests of a breadboard model are described which show cavity gains of 10 with noise levels equivalent to 2 to 10 ppm CO.

Jan 1, 1975

1. Proposals were submitted to the Western Administrative Center of the US Bureau of Mines, Denver, Colorado on 30th December, 1974 and Contract No J 0255003 was awarded, the effective date being 8th May, 1975. Dames and Moore, Denver, are associated with PD-NCB Consultants in regard to environ-mental problems, surface mining practice and legislation in US. BACKGROUND TO THE STUDY 2. Under the threefold pressures of -increased domestic fossil fuel demand -increased value of domestic energy resources -increased demand for environmental protection and safety

Jan 1, 1976

By Carl R. Peterson

[In lTI n,v und I'gr'oun nllnin~ Opt'I'ali n' the high . t cost is the loading and I 3ulage of t tln-of -D"'line ot'. 01' hauling costs can be r duced signifi-cant\v with the us ~ (r \) >It corn'e)'OI' " a COnlTllOn pl'acti c i.n coal and other s 0 t'L rn I n r' a l III i, n e , '. Jf 0 vel s i z ' () f' e can bee 1 i 11.11 tl ate I rH'i 0 I' lO C n v e . in g, ]

Jan 1, 1976

By Virgil A. Marple

The primary purpose of this contract was to evaluate methods and techniques by which the size distribution acid concentration of mining-related dusts can be measured. One result has been the development of a portable, battery-operated optical particle counter/ multi-channel analyzer system which can he used to determine the size distribution and concentration of mining aerosols. One important aspect of this program has been the development of a calibration technique which relates the output of the optical particle counter to the penetration of the particles through an impactor: This results in a calibration curve in terms of the aerodynamic or Stokes' diameter or the aerosol particles. Using this technique, calibrations were performed on coal, silica, Arizona road dust, potash, and rock dust (corer ore) aerosols. Another task of this program was the calibration and evaluation of the GCA respirible dust monitors (RMD) 101-1 and 301. The results of evaluation showed that the instruments were within the manufacturer's specification of ±25% of the true mass concentration up to about 15 mg/m , if the dust particles were in a size range from about 0.7 to 10 µm aerodynamic diameter. Particles smaller tan about 0.7 µm were not collected by the instrument and particles larger than about 10 µm were lose in the inlet. Other tasks included performing field studies in cooperative research programs with the Bureau of Mines personnel, development of a portable polystyrene latex generator for use in optical particle counter calibrations in the field. The incorporation of impactor classification devices on the inlets of aerosol mass measuring instruments to give mass size distributions, and a study of the density of coal particles as a function of the particle size.

Jan 1, 1977

By S. K. R. Iyengar

This report presents the results of a study to develop optimal designs for light-weight mine roof supports for use in underground coal mines. A load capacity of 196 kN (22 tons) and a height adjustable between 1.829 m (72 inches) and 2.438 m (96 inches) were taken as the design parameters and the design goal was a unit weighing less than 22.3 kg (50 lbs). Three alternative design concepts were explored, viz. mechanical, hydraulic, and hydro-mechanical and a total of 13 designs analyzed in detail. Steel, aluminum alloy and composites were the main potential construction materials investigated for suitability from structural, life, and safety and other considerations. The designs considered most promising for development were: (i) the mechanical screw-pin type using telescopic tubes and a fine adjustment screw thread section (ii) the all-hydraulic type, of steel, aluminum alloy or aramid graphite construction (iii) the hydro-mechanical design using telescopic tubes and a short stroke hydraulic cylinder for fine adjustment It is shown that by using realistic mathematical models for stress and deflection calculations, it is possible to reduce prop weight to the design goal. The analysis presented for all-hydraulic props is applicable to hydraulic cylinders on all mining equipment and similar machinery. This report includes the computer program and user's guide for analyzing hydraulic cylinders as well as a cross-indexed bibliography on structural composites.

Jan 1, 1978

By R. D. Eash

The purpose of this research contract was to develop and test a Saran latex modified portland cement concrete lagging to be used as a replacement for wood lagging. The scope of work performed was divided into four phases: Phase I - Engineering Criteria; Phase-! I1 - Design Study; Phase III - Fabrication of Lagging; and Phase IV - Prototype Demonstration Project. Each phase of work was completed and is described in detail in this report. The prototype latex modified concrete lagging developed in this program weighed 52 pounds. When tested in flexure, it supported center point loading of 4500 pounds and under 1/4 point loading it supported loadings of 7000 pounds. Deflections at maximum loading ranged from 1/2 to 1 inch. Maximum deflections exceed 2 inches. The lagging does not exhibit catastrophic failure. Two hundred and twenty of the LMC lagging were produced and shipped to the Bunker Hill Company in Kellogg, Idaho for installation in their mine at the 17 level. The lagging are performing satisfactory after 22 months exposure in the mine.

Jan 1, 1980

By C. A. Cole

This work consists of research in cable fault location and the construction of four field-test units based on the research. Swept-frequency sounding of mine cables with RF signals has been the technique most thoroughly investigated. The swept-frequency technique is supplemented with a form of moving target indication (MTI) to provide a method for locating the position of a technician along a cable and relative to a suspected fault. Separate, more limited investigations involved high-voltage time domain reflectometry and acoustical probing of mine cables. Particular areas of research included microprocessor-based control of the swept-frequency system, a microprocessor-based fast Fourier trans-form for spectral analysis, RF synthesizers, transmit-receive switches, RF receivers, cable dispersion-compensation techniques, low-voltage multielement display systems, and techniques for injecting or recovering RF energy through cable walls in support of clamp-on fault locators.

Jan 1, 1982

By R. W. Courtney

The objective of this study is to make a critical evaluation of the magnitude and extent of electrostatic hazards in typical U.S. mining operations and to assess the adequacy of techniques, materials, and equipment for detecting and minimizing these hazards. This was accomplished with an incident/accident survey, mine visits, literature search, and engineering analysis. It was concluded that it would be desirable to (1) utilize ground fault interrupters to minimize stray current from electrical utilities, (2) decrease the current and electrostatic sensitivity of electric detonators used in areas with a high incidence of lightning strikes or troublesome stray currents, (3) institute quality control and test standards for blasting material and protective devices, (4) establish an electrostatic monitoring program for loading ANFO in plastic lined holes, and (5) establish a risk criteria for operator exposure in mines.

Jan 1, 1982

By M. J. Waller

Surface resistivity techniques were used at four field sites to monitor changes in apparent resistivities with variations in soil moisture content in the vadose zone. Apparent resistivity values were correlated with gravimetric moisture contents from soil samples taken at each site. Tensiometer readings were taken at two sites and correlated with the results of gravimetric moisture contents and apparent resistivities. Moisture at two of the sites was added by extensive watering; rainfall events were monitored at the other two sites. A recharge event at a dewatering program was monitored at a fifth site. A Ghosh-Koefed multi-layer computing algorithm was used to derive true resistivities from bulk or apparent resistivities. An automated data acquisition system was developed to measure resistivity changes and to process the data in the field. These studies are the first to evaluate measurement of moisture migration in clay rich soils using surface resistivity techniques. Results indicate that surface resistivity techniques readily measure changes in moisture contents in the vadose zone in clay rich soils. Correlation of apparent and true resistivity values with gravimetric moisture contents is more complex and requires additional research.

Jan 1, 1986