Search Documents

By KNona C. Liddell

Goethite is an important naturally occurring sorbent for divalent heavy metals and has often been used as a model compound in studies of adsorption on oxide mineral surfaces. Surface complexation modeling, surface spectroscopy, and electrochemical techniques have all been applied to goethite adsorption. Modeling studies have shown that usually several different sets of fitted parameters are equally successful in representing surface charging and adsorption data. Surface spectroscopic data are proving valuable in determining the nature of the surface sites, and refined models now incorporate structural information on interatomic distances and coordination numbers. Multisite surface complexation models can give very good fits to surface charging and adsorption data, but further improvements are needed to better represent surface reactions involving exchange of protons and divalent cations. Recent experimental and modeling studies on adsorption of divalent transition metals on goethite are described and the present status of the field is assessed.

Jan 1, 1999

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By Norberto Benitez, Christian Ludwig, Simona Regenspurg, Fabian Mendez

"Navarro is the main garbage dump in the city of Cali (Colombia). Operated since the late 1960s it collects about 1.600 tons of waste daily. The environment surrounding Navarro is highly contaminated and the pollutants released by the dump threaten human health in the adjoining neighborhoods. The goal of our project is to identify major pollutants released from the dump and their distribution in the surrounding ecosystem. In a first phase of the sampling and analysis program landfill leachate was collected and screened for heavy metals and for the most common persistent organic pollutants. This allowed us to identify the most relevant compounds on which we focused in a more detailed second phase investigation. These compounds were quantified in the vicinity of the landfill (groundwater, surface water, drinking water and soil) to get information on their mobility and possible pathways into the human body.IntroductionThe usual technique of waste disposal in most developing countries is by landfilling on not -, or not well controlled sites, where people live close by or even on the waste itself. A typical example for this practice is Navarro, the main garbage dump in the city of Cali (Colombia). Operated since the late 1960s it now consists of about 23 million tons of household and industrial waste. The dump is located on a wetland in the riverbed of the Cauca River, the main drinking water source for Cali. Two ponds of unknown permeability located next to the landfill collect a fraction of the waste leachate. During the rainy season, the ponds frequently overflow and drain into the soil (alluvial, loamy sediments) of surrounding sugar cane fields. The environment of Navarro is assumed to be highly polluted and there is evidence that it affects the health of nearby inhabitants. Specifically, the incidence of respiratory diseases was higher among vulnerable individuals (<3 and >50 years old) living in a <3 km perimeter of Navarro as compared with a control group (Solano et al., 2006). Further, a clustering of extremely rare congenital malformations (sirenomelias and cyclops) was observed in a small area during a short time period (<6 months) (Filigrana et al., 2008)."

Jan 1, 2008

By Y. A. Chang, L. M. Pike, C. R. Kao

"Knowledge of the site preference of ternary solute additions is essential to developing an understanding of how these solutes affect the properties of B2 intermetallic compounds. A quasichemical model will be presented which is able to predict the site preferences of dilute solute additions to tliple defect B2 compounds. The only parameters required are enthalpies of formation at the stoichiometric composition. General equations are developed which can be used to determine site occupations and defect concentrations for dilute as well as non-dilute solute additions. These equations use atom pair bond enthalpies as the parameters. It is found that the site preferences of dilute additions are not always in agreement with predictions based on the solubility lobes in ternary Gibbs isothelms. Predictions for dilute additions to NiAl and FeAl are compared to expel1mental results found in the literature. Satisfactory correlation is found between the model and the experimental results. In addition, the predictions from the model on vacancy concentrations in Fe doped NiAl are compared to recent experimental results by the authors.1.0 IntroductionIntennetallic compounds with the B2 crystal structure such as NiAl and FeAl have been investigated recently for possible use as structural materials in high temperature, oxidizing, and/or corrosive environments. The major limiting property of these materials has been a lack of sufficient room temperature ductility. Attempts to improve the ductility have often been made through ternary or higher order alloying. For B2 compounds, substitutional alloying additions can occupy either of the two sublattices and this site occupancy can be crucial in determining how the alloying addition affects the properties of the alloy. In this manuscript we will discuss the use of thelmodynamic modeling to predict the site occupancies of ternary alloying additions in B2 compounds with the triple defect structure."

Jan 1, 1996

By S. J. Kohut

Until recently SX-EW technology has only been used to produce conventional cathode for the cyclical commodity marketplace. Unlike electrorefining, SX-EW lends itself to the integration with the downstream manufacturing technologies for direct mine site production of value added products. The integration of SX-EW and downstream manufacturing results in the elimination of redundant process steps, the cost savings, and the access to value added product markets which can buffer the producer from swings in the cathode market. SX-EW production of copper powder and powder-based products has been demonstrated at the pilot plant level. The SX-EW process has been successfully redesigned to meet the more specific demands of engineered products. Challenges include the solution purity, the cell ventilation, the high current density operation and the product handling. Successful demonstration of mine site production of value added SX- EW products opens up new non-commodity marketplaces to the mining industry.

Jan 1, 1999

By Zemin Ma

A novel chromate [Cr(VI)] reducing bacterium was isolated from chromite ore processing residue disposal site of China and identified as a Leucobacter sp. by 16S rRNA gene sequence homology. The minimum inhibitory concentration of strain CRB1 was 820 mg l-1 of Cr(VI). The reduction of Cr(VI) occurred only under aerobic conditions. With an initial concentration of 2.5×108 cells ml-1, 1800 mg l-1 of Cr(VI) was reduced entirely within 38 h under the optimum conditions, at 30 °C and pH 9.0. Increasing Cr(VI) concentrations prolonged reduction process and higher cell densities meant quicker reduction. A blue precipitate was produced during chromate reduction of strain CRB1, which was binding to the surface of bacterial cells and determined as trivalent chromium with electron paramagnetic resonance (EPR) spectrometry. The conspicuous chromate reduction ability of Leucobacter sp. CRB1 suggested a potential for bioremediation of Cr(VI) containing wastes.

Jan 1, 2008

By Philip L. Sibrell

A new process utilizing pulsed fluidized limestone beds was tested for the remediation of acid mine drainage at the Friendship Hill National Historic Site, in southwestern Pennsylvania. A 230 liter-per-minute treatment system was constructed and operated over a fourteen-month period from June 2000 through September 2001. Over this period of time, 50,000 metric tons of limestone were used to treat 50 million liters of water. The influent water pH was 2.5 and acidity was 1000 mg/L as CaCO3. Despite the high potential for armoring at the site, effluent pH during normal plant operation ranged from 5.7 to 7.8 and averaged 6.8. As a result of the high influent acidity, sufficient CO2 was generated and recycled to provide a net alkaline discharge with about 50 mg/L as CaCO3 alkalinity. Additions of commercial CO2 increased effluent alkalinity to as high as 300 mg/L, and could be a useful process management tool for transient high flows or acidities. Metal removal rates were 95% for aluminum (60 mg/L in influent), 50 to 90% for iron (Fe), depending on the ratio of ferrous to ferric iron, which varied seasonally (200 mg/L in influent), and <10% of manganese (Mn) (10 mg/L in influent). Ferrous iron and Mn removal was incomplete because of the high pH required for precipitation of these species. Iron removal could be improved by increased aeration following neutralization, and Mn removal could be effected by a post treatment passive settling/oxidation pond. Metal hydroxide sludges were settled in settling tanks, and then hauled from the site for aesthetic purposes. Over 450 metric tons of sludge were removed from the water over the life of the project. The dried sludge was tested by the Toxicity Characteristics Leaching Protocol (TCLP) and was found to be non-hazardous. Treatment costs were $43,000 per year and $1.08 per m3, but could be decreased to $22,000 and $0.51 per m3 by decreasing labor use and by on-site sludge handling. These results confirm the utility of the new process in treatment of acid impaired waters that were previously not amenable to low cost limestone treatment.

Jan 1, 2003

By Shunhong Huang

Thirty-five soils were sampled from three sites at different distances from chromium slag heap of a Iron-alloy factory, namely, nine from site A located under the chromium slag and eighteen from Site B in the vicinity of the factory and eight from site C far from the factory. The contents of total Cr in these soils from site A, B and C were 1666.0±1310.9 mg? kg - 1,1136.2±1844.6 mg? kg - 1 ,300.4 ±165.1 mg? kg ? 1, respectively. The contents of water soluble Cr were 59.3±77.57 mg? kg ? 1,0.6 ±0.3 mg? kg - 1 ,0.5±0.3 mg? kg - 1 , respectively. In order to evaluate soil health, the activities of four soil enzymes (catalase, polyphenol oxidase, dehydrogenase, alkaline phosphatases) were analyzed. The results have shown that dehydrogenase activity was greatly depressed by conditions in the heavy chromium-contaminated sites. Negative correlation was observed between dehydrogenase activity and the distance from the chromium slag heap, however, the activities of catalase, polyphenol oxidase, alkaline phosphatases in soils from the three sampling sites mentioned above did not differ significantly. The result imply that of dehydrogenase activity could be used as an indicator for the chromium pollution level in the area of Iron-Alloy factory and for the stability level of the soil ecosystem.

Jan 1, 2008

By D. W. Collins

The uptake of gold from halide solutions by activated carbon has been investigated using various techniques. Halide systems typically exhibit combined adsorption-reduction type behavior. In an attempt to gain more information about the nature of these processes, samples of synthetic highly-oriented pyrolytic graphite (HOPG) were contacted with aqueous solutions of gold-iodide. HOPG represents a model structure for activated carbon comprising of basal- plane sites, edge sites, and various defect sites. Two basic instrumental methods were used to examine the uptake of gold by HOPG. The first was standard X-ray photoelectron spectroscopy (XPS). The other involved several scanning probe techniques. XPS clearly indicated a preferred uptake of gold at edge sites. However, iodine appeared to be distributed on both basal-plane and edge sites. At low iodine additions, tapping mode AFM showed that clusters were concentrated along steps and surface defects. At high iodine concentrations, the HOPG surface was uniformly covered by iodine.

Jan 1, 1998

By C. W. Vierrether

Mineralogical analysis contributes directly to the selection of applicable beneficiation techniques for a given site. Tentative remediation methods for use on the Sharon Steel tailings in Midvale, Salt lake County, UT, were determined in part by mineralogical characterization. A systematic characterization scheme was employed to identify mineral species, mineral associations, and grain size. This paper presents the mineral content and distribution data collected for site characterization. This data was used to determine areas that were representative of the total tailings at the Sharon Steel site. Although this was the main focus of characterization, other useful information was obtained. The approximate location of "old jig tails" was identified and insight on possible arsenic, mobility through the pile was also obtained from the mineralogical study.

Jan 1, 1991

By Stephen W. Paff

The EPA has estimated that there are over 3,000 sites across the United States contaminated with lead. Techniques to remediate these sites include standard stabilization/disposal technologies, reclamation of lead using secondary lead smelters, soil washing, and biological removal technologies. In this paper, the current technologies used for lead remediation will be reviewed. Factors affecting the use of each technology, such as range of applicable concentrations, soil types, interferences from other contaminants, economics, and current technology status will be assessed. The paper will also focus on the results of a recent study completed by the Center for Hazardous Materials Research (CHMR), in conjunction with a major lead smelter, which demonstrates that secondary lead smelters may be used economically to reclaim lead from a wide range of lead-containing materials frequently found at Superfund sites. Such materials include battery case materials, lead dross, and debris containing between 3 and 70% lead. The results of development work completed by CHMR on the Acid Extraction Treatment System (AETS), which has been demonstrated to extract Lead from soils containing up to 30,000 mg/kg lead, will also be presented. The use of these technologies will be compared with other options for the remediation of sites.

Jan 1, 1994

By Margarete Kalin

Mine abandonment is associated with the securing of access to underground workings, shafts, raises and adits. Waste rock piles and tailings are generally contoured and revegetated. When the waste materials contain pyritic material seepages can often emerge long after the physical reclamation work has been carried out. Their extent and origin has to be delineated to facilitate remedial measures. The depth to which the seepages extended can be determined with an electromagnetic (EM) survey. This paper reports on the experience gained using a winter and a summer EM survey correlated with measurements of specific conductivity at the sediment water interface. Lake sediments and ponds which represent a homogenous background material are good media, where specific conductivity and electromagnetic conductivity can be correlated. The origin of the seepage within the recontoured mine site requires detailed site knowledge, as many anomalies in heterogenous materials such as represented by a mine site are evident.

Jan 1, 1994

By J. Bostjancic

As wastewater discharge regulations become more stringent, power plants, manufacturing plants and other industrial sites are looking for ways to reduce makeup water requirements and to recycle and reuse as much wastewater as possible. In some cases, environmental regulations require zero liquid discharge, meaning all wastewater must either be retained on site or reduced to solids for disposal off site. Zero liquid discharge or "closed-loop" wastewater treatment systems using evaporators and other process equipment have been well-accepted in recent years. Often overlooked is the fact that zero discharge is not just the latest fashion--many commercial zero liquid discharge systems have been in operation since the mid-70&apos;s. This paper will give specific examples of zero liquid discharge operations from 1974 to the present, showing how evaporation equipment and processes have changed to meet the requirements of industry and environmental regulations.

Jan 1, 1996

By László I. Kiss, Verena Mackowiak, Alexandre Perron, Dominic Toulouse, Alicia Liedtke, Sándor Poncsák

"Bubbles play a very important role in different metallurgical applications like for example in electrowinning. During heterogeneous nucleation, the maximal size of the bubbles growing at the nucleation sites as well as the nucleation frequency is determined by the so-called detachment condition. Detachment occurs when the external forces acting on the bubble exceed the retaining forces along the solid-gas-liquid triple interface line. The phenomenon depends strongly on the shape and orientation of the solid surface and on the nature and strength of the external buoyancy and drag forces. In the present study the detachment conditions of bubbles from downward facing horizontal and inclined plates were studied experimentally under the effect of gravitational and hydrodynamic forces. The results show the deformation of the bubbles under the effect of the external forces and the detachment conditions as function of the bubble volume.IntroductionIn heterogeneous nucleation bubbles are generated at the so-called nucleation sites along the solid-liquid interfaces. They continue to grow there and after they reached a certain size they detach from the solid surface and leave the nucleation site. This scenario is well known both in boiling and electrolysis. During the growth period a stable equilibrium exists between the forces that retain the bubble at the nucleation site and the forces that try to remove it. This equilibrium evolves with the increasing volume of the bubble to the point when the detachment forces overcome the retaining forces.The life of a single bubble generated by heterogeneous nucleation can be divided into two periods separated by the detachment - or in other words by the departure - of the bubble: first the growth at the nucleation site and then the movement away. The knowledge of the detachment conditions makes possible the determination of the maximal volume of the bubble at the nucleation site that, in tum, makes possible the determination of the nucleation frequency. This is why so many researches have been directed toward the clarification of the details of the bubble detachment in the past decades. The equilibrium between the attaching and separating forces depend on the presence of body, surface and flow induced forces in the liquid, on the geometry and orientation of solid surface, on the properties of the solid-liquidgas system etc."

Jan 1, 2004

By Jari Aromaa, Antti Kekki, Olof Forsén

"The deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential depends on surface morphology, surface film resistance and additives on cathode surface. The effects of surface properties on copper nucleation and growth rates were studied for used stainless steel blanks from several tankhouses. The surfaces of the blanks were characterized with electrochemical and mechanical methods. Electrochemical deposition tests were done at current density of 300 A/m2 for 10, 30 and 60 seconds. The nucleation density and copper coverage were estimated using image analysis. The surface film resistance did not correlate with copper growth. Increasing surface roughness correlated with lower copper growth.IntroductionStainless steel cathode blanks in copper electrorefming are usually made of AISI 3 I6L type steel. They have a typical lifetime over 10 years. During use the surface will collect deposits and become rough due to wear and corrosion. These factors can affect the nucleation and growth of copper. The nucleation and deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential can depend on surface film resistance, surface morphology, and additives adsorbed on cathode surface.The deposition potential of metallic ions on a foreign substrate is usually higher than the deposition potential on the electrode made of the same metal due to crystallographic substrate/metal misfit [I]. If the substrate has traces of the depositing metal they will be preferential growth sites. For a smooth deposit a large number of simultaneous nuclei is necessary. However, excessive nucleation density can lead to porous deposits [2]. Surface films of good conductivity are needed for dense nucleation and small nuclei. On cathode blanks the number of active sites increases with increasing surface film conductivity [3-5] and/or surface film porosity [6]. On AISI 3 I6 L stainless steel a more resistive oxide has been found to limit favourable sites for copper nucleation and more conductive film promoted high-density copper nucleation [7]. Also Urda-Kiel et al. have concluded that thicker oxide layers on AISI 304 stainless steel resulted in lower nucleation [8]. Increase in overpotential or current density activates more and more of the potential nucleation sites and this can be seen as higher number of nuclei [9] or smaller average distance between nuclei [10]."

Jan 1, 2012

By Young-Geun Park

A new decarburization model for the RH system was constructed for calculating the decarburization reaction using a three-dimensional fluid dynamics program. The entire fluid flow in the RH process was calculated by evaluating the shape and volume of the plume zone, formed by Ar gas blown through multiple nozzles on the wall of the snorkel. On the basis of this fluid flow, the decarburizaiton reaction was calculated through establishing the decarburization reaction model, which considers the thermodynamics, reaction kinetics, and the decarburization sites (Ar bubble surface, bath surface, and the CO bubble fomtation at inner sites). The results from this model were compared with a real RH operation results with good agreement. Because it is possible to predict the carbon concentration at various conditions using this model, it may be useful in increasing the decarburizaiton rate. Key words : RH process, plume zone, decarburization, Ar bubble surface, bath surface, inner site, circulation flow rate.

Jan 1, 2001

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By Lee Fergusson

"The primary features of ViroMine™ Technology are introduced and applications of ViroMine™ Technology to mine site remediation and the treatment of a variety of intractable waste-streams, including a technical discussion of acid neutralizing capacity, metals binding capacity and longterm stability of results. Outcomes from four applications at high-profile international mine sites are presented: 1) the superfund site at the Gilt Edge Mine, South Dakota, USA (four years of data on the treatment of acidity, TDS and metals such as Al, Co, Fe, Mn and Zn); 2) one of Australia’s most polluted sites at King River Delta in Tasmania (treatment of TAA and TPA, and metal and metalloid contaminants such as As, Cr and Hg); 3) The Aljustrel “Aqua Forte” mine site in Portugal (high acidity, metal and metalloid contaminants such as Al, As, Cu and Zn) and 4) the Ulsan Iron Ore Mine at Ulsan, South Korea (treatment of metal and metalloid contaminants such as As, Cd and Ni).IntroductionThe commercialisation of ViroMine™ Technology has resolved some of the most intractable pollution issues associated with historic mining ventures on a global scale and has facilitated the neutralisation of Acid Rock Drainage (ARD), remediation of acidic and metal contaminated impoundments (including tailings dams) and promoted revegetation on tailings deposits and waste rock dumps. ViroMine™ Technology also enables current mining ventures to manage effluent simply and efficiently to meet increasingly stringent environmental standards and is enabling the mining sector to reconceptualise the management of mine spoil. The abilities of ViroMine™ reagents to neutralise the actual and potential acidity of sulphidic mine spoil coupled with the ability to bind metal and metalloid contaminants into non-bio-available forms are the key features delivering environmental and economic benefits to the mining sector and the broader community. Results from four projects utilising ViroMine™ Technology are presented to highlight the suitability of ViroMine™ Technology to treat all forms sulphidic mining wastes. 37"

Jan 1, 2008

By C. O. Bounds

The performance of AB5-type alloys for hydrogen absorption including the electrochemical absorption as an electrode for rechargeable batteries has been demonstrated&apos; to be a complex function of the composition, microstructure and surface condition. The compositional studies have focused primarily on substitutions for Ni on the B-site (e.g. Co, Al, Mn, etc.). This current study examines the effect of rare earth substitutions for La on the A-site and considers both other "light" rare earths (Ce, Nd, Pr) and "heavy" rare earths (Dy, Sm, etc.).

Jan 1, 1997