Search Documents

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By R. Wensel

A composite material consists of two or more dissimilar components. These dissimilar components retain their identities when mixed together and contribute to the properties of the composite. A composite usually consists of two parts, the matrix and the reinforcing material, or extender that is added to the matrix. Typical materials used as the matrix in composites are metals, polymers, and ceramics. The reinforcing material can be added for any number of reasons. For instance, if the matrix is expensive, an inexpensive filler may be added to the matrix to lower the cost of the product without sacrificing properties. An example of this is calcite (CaC03) which is added to systems such as polyvinyl chloride (PVC), to lower the cost. Reinforcements may also serve as a means to enhance the properties of the matrix material. For example, carbon fibers are frequently added to plastics to increase their strength, and glass spheres may be added to plastics to improve flexural strength. Mg(OH)z is added to polymers to give the property of fire retardancy. The latter is the focus of this paper.

Jan 1, 1995

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

By S. S. Peng

To prevent mine floor heave, the mechanisms of floor heave must be fully understood. Based on the field study, the mechanisms of two types of floor heaves are analyzed in this paper. The mechanical models for the two types of floor heaves are developed. The floor heave can be predicted by the developed mechanical models and the control measures are recommended.

Jan 1, 1995

By Ronald B. Stone

This paper describes a proposed solution to the problem of mining a 315 foot diameter unsupported sphere at a depth of 2700 feet in a salt dome by conventional mining methods. The proposed solution utilizes many of the varied technologies available to the mining engineer for solving mining and underground construction problems. The following are reviewed in the paper: A. The location of the sphere within the dome as required by construction criteria. B. The relation of the location of the access shafts to the sphere. C. The rock mechanics theory in relation to the salt dome and large size of the excavation. D. The proposed "honeycomb" method of mining which will be a partial answer to rock mechanics stability requirements. E. The equipment which it is recommended be utilized to accomplish the construction. F. The rock mechanics measuring instruments proposed. G. The methods of disposal of the mined salt. Conclusions and areas of further study are outlined in the final statement.

Jan 1, 1968

By James P. Connell

The American Concrete Institute defines "shotcrete" as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity unto a surface." This definition thus includes what is traditionally known as "gunite," which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this paper. In 1914, following the invention of the mortar gun in 1907, the then Chief Engineer of the U.S. Bureau of Mines, George Rice, developed the guntie process for underground test work at the bureau facility at Bruceton, Pennsylvania. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto Tunnel in California. The greatest development was In Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Intially, shotcrete was used to reduce manpower requirements for forming; and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately niter the opening had been made. The incorporation of wire mesh into the shotcrete led to the New Austrian Tunnel Method, or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the U.S. reliance on wood or steel supports in main line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to the new and seemingly unrealistic lighter shotcrete support.

Jan 1, 1977

By R. A. Wyman

What unusual features are there about finding, winning, and using the industrial minerals of Canada which may be of interest and yet not widely known. Have you, for example, ever wondered where the raw material for those distinctive greenish grey statuettes, so readily recognizable as Eskimo carvings, comes from? Although stone suitable for carving is obtained at several northern locations, in recent years the Federal government, the Quebec government, and one or two private companies have shipped supplies of various rock types from other sources to central distribution points in the Canadian north for the express purpose of providing Eskimo artists with raw materials for carving. Canada is well endowed with industrial minerals, the extent and variety of which may be observed by a perusal of Table 1. In this table, materials currently produced are shown in the left-hand column; materials which are bordering upon economic viability are listed in the middle column; and materials which have been found in Canada in possible exploitable quantity, but for which [ ]

Jan 1, 1970

By Ben L. Seegmiller

How to obtain optimum slope angles for future open pit mines using the rock mechanics approach is the subject of this paper. In the past ten years significant developments in open pit rock mechanics have come about. This has been due to the mining industry's need for the steepest, yet safe, pit slope angles attainable. Requirements for economically achieving slope stability and the actual payoff that may be achieved through stability studies have been previously discussed', by stability engineers. While the emphasis has generally been placed on the concept of "stable slopes" in the past, it is suggested that emphasis now be placed on "optimum slopes" or "optimum slope angles". A definition of an optimum slope angle is one which (1) is as steep as possible and practical from orebody and mining constraint standpoints and yet, (2) maintains the accepted standard of safety defined by a safety factor against failure and/or a probability of failure. In other words, the emphasis is placed on achieving practical stability results as defined by safety and economic considerations, as opposed to simply achieving stability. The essential purposes of this paper are to (1) outline the need for optimum slope angles, (2) discuss the procedures for using the rock mechanics approach in slope angle design for a future open pit and (3) specify the end results that may be achieved by using such an approach. While the basic concepts and recommendations outlined in this paper may be equally applicable to soil as well as rock slopes, the emphasis and procedures have been directed at rock slope angle design.

Jan 1, 1976

By Jerome F. Sheldon

The earliest recorded history in the use of belt conveyors in the United States is in O. Evans' "Miller's Guide" published in Philadelphia in 1795. Evans defines a conveyor as a "broad endless strap of thin pliant leather or canvas revolving over two pulleys in a case or trough." (Ref. 1) In this definition, pulleys are being used in a bulk material belt conveyor application. Pulleys used in belt drives can trace their origin back to 1200 A.D. In fact, Engineers had considerable experience designing them into drives transmitting greater horsepower than those used in the early belt conveyors. In belt conveyor application, a pulley's purpose is primarily three-fold, 1) support the belt in directional changes, as designed in the conveyor, 2) transmit driving power to the belt, and 3) guide or train the belt. There are various types of pulleys used in belt conveyor systems and these are thoroughly covered in "Belt Conveyors For Bulk Materials" prepared by CEMA, 1966. For our discussion, however, the most common used in belt conveyors are drive pulleys, snub pulleys, head pulleys, tail pulleys, takeup pulleys and bend pulleys. The drive pulley imparts the driving force to the belt and may be located at the head or discharge end of the conveyor, in return strand, or at the tailor loading end of the conveyor. A snub pulley is located near the drive pulley to provide more arc of contact between the belt and pulley for maximum

Jan 1, 1971

By Paul R. Weber

Open-pit mines are constructed in materials characterized by the complete range of geologic materials from the most recent alluvial sediments to hard intact crystalline rock. The determination of stable slopes in recent alluvium is in the realm of soil mechanics, an established engineering discipline, well founded on theoretical development and years of substantiating experience. The analytical tools of the soils engineer are chiefly derived from continuum mechanics wherein load-deformation response is governed by mass properties of the substance. At the other end of the spectrum, slopes in hard unweathered rock can generally be analyzed in a straightforward manner by the methods of discontinuum mechanics wherein the properties and orientations of joints control the response of the material. This approach is exemplified by the classical work of Terzaghi (1962). In between these two extremes is a gray area of material types which are composed of stiff soil and incompetent rock. This area is of importance to the mining engineer, since a large portion of open-pit mines is excavated wholly or in part into incompetent rock. This paper describes an approach to pit slope design in incompetent rock in which the material behaves essentially as a continuum. A wide range of geologic materials from stiff soil to poorly indurated sandstone and shale to crushed or weathered crystalline rock appear to fit in this category. These materials all possess certain mechanical properties which must be accounted for in a realistic assessment of slope stability. These properties include nonlinearity, s tress -dependency, and inelasticity. Further considerations involve residual stresses and time-dependent seepage pressures where groundwa.ter is present.

Jan 1, 1971

By F. L. Pirkle

A heavy mineral deposit about 1.6 km (1 mile) in length, 0.13 km (0.08 mile) in width and averaging about 3 m (10 ft) in thickness is exposed approximately 130 km (80 miles) east of Denver, along Interstate 70, in Elbert county, CO near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium ridge. The dominant heavy minerals, accounting for about 70% of the total heavy-mineral suite by weight, are ilmenite, garnet and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Ga. Thus, Titanium ridge provides evidence that heavy-mineral accumulation models for late cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2012

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021

By John Murray, Daniel Ebin, Robert Gould, Yiming Sun, Lizan Gilbert

The Atlanta Plane Train Tunnel West Extension is being constructed at Hartsfield-Jackson Atlanta International Airport using the Sequential Excavation Method (SEM). The tunnel has shallow ground cover and mixed-face conditions and passes underneath the SkyTrain and MARTA stations and airport terminal buildings. It includes a twin tube Bifurcation with a span of over 45 feet and ground cover of 12 feet. A flat roof is being constructed at the Bifurcation to maximize rock cover and minimize surface settlements. This paper focuses on design and construction challenges for the Bifurcation and tunneling beneath the world’s busiest airport, while minimizing impacts to operations.

Dec 1, 2022

By M. Trim, Y. Sun, D. Tepavac, A. Kumar

Configuration of Rozelle Interchange Project’s ventilation system required design and construction of some of the largest and tallest underground civil caverns attempted in Australia. The paper focuses on the technical challenges of designing these caverns within a heterogeneous, generally weak sandstone under highstress conditions while providing a construction sequence that would align with the contractor’s preferred techniques and schedule. Various construction techniques were investigated, but ultimately an observational approach relying on a construction sequence and specialized instrumentation met both the designer’s and contractor’s requirements. Relevant data obtained from excavations and the construction monitoring program are presented within.

Dec 1, 2022

By Francis X. McCullough

After OSHA published a Notice of Proposed Rulemaking on August 5, 1983, to revise its standards for Underground Construction, many contractors and their representative associations became concerned by the sweeping changes in the proposed rule. After reviewing all of the evidence and testimony on file with OSHA, the contractors presented extensive written and oral testimony to the Department of Labor in Washington, D. C. to help insure that the final published rule would be effective without jeopardizing the economic viability of the industry. The results of those efforts, the entire OSHA rulemaking process, and the opportunity for the construction industry to participate in that process will be discussed.

Jan 1, 1985

By Kevin A. Foo, Murray D. Bath, John H. Canterford, Arnaldo Ismay

There is no doubt that the dominant future source of gold will be the so-called refractory ores, especially those with gold in a pyrite/arsenopyrite matrix. Minproc Engineers is taking an active role in establishing detailed design criteria for a number of apparently competing processes. This involves generating a detailed understanding of the metallurgy involved, systematic pilot plant testing, and the application of advanced engineering technologies. This presentation outlines the approach adopted by Minproc as well as the design criteria for several current projects.

Jan 1, 1989

By Garry M. Hughes

Lynn lake, Manitoha, where Sherritt has operated a copper-nickel mine since 1954, is located north of the 56th parallel approximately SOO miles north of Winnipeg. Sherritt's new, 3,000 tpd, copper-zinc Fox Mine is situated 30 miles southwest of Lynn lake. This paper focuses on the Fox Mine concentrator, hut first some background information. Sherritt Gordon Mines Limited started mining operations as a copper-zinc producer in 1931 at Sherridon, Manitoba, 150 miles south of Lynn Lake. As Sherridon fizzled out development of a series of nickel-copper orebodies commenced at Lynn Lake. The Forward process was developed to treat the nickel concentrate from the Lynn concentrator. Sherritt's ammonia leaching process is now history and is expected to gain more prominence as pressure is applied to the mining industry for closer environmental control. But few are aware of the fact that the present Lynn Lake crushing plant and concentrator were dismantled in the autumn of 1951 and freighted from Sherridon by tractor train during the winters of 1952 and 1953. The copper-zinc orehody at Fox Mine was discovered early in 1961 by geophysical methods which included both airborne and ground surveys. It is part of a ,large body of massive and semi-massive sulphides consisting chiefly of pyrite; with chalcopyrite, sphalerite (containing 7-9% iron) and pyrrhotite in varying proportions which occur within a series of volcanic and sedimentary rocks. The total mineralized zone is a lenticular body with a minimum average length and width of 1,350 feet and 66 feet respectively, to the explored depth of 2,000 feet. The average sulphide content is 67%. Higher zinc zones are masses of pyrite grains cemented by sphalerite with lower than average copper content. Zones higher in copper and lower in zinc are slightly more quartzose. Gold and silver are present in small amounts roughly proportional to the copper content.

Jan 1, 1971

By Yuting Xue, Mark Van Dyke, Zoheir Khademian

Borehole scoping has been widely used in the U.S. underground coal mines as a method for geologic mapping and stability analysis because it is very useful for identifying rock types, voids, fractures, and formation boundaries through the direct observation of the borehole wall. An image stitching technique was proposed to generate panoramic borehole images from side-view borescopes in a previous study. However, the generation of panoramic borehole images can be affected by the borehole condition because the image stitching process highly depends on the key point detection and matching. The presence of dust and water could have a significant influence on the detection of key points. In this study, the influence of borehole conditions on panoramic borehole images was studied from the success of image stitching and the visibility of geologic features and lithology changes. Borehole videos recorded at different times, when the same borehole was freshly drilled, freshly washed with water and 12 days after washing, were processed with the proposed technique. The comparison of the stitched images shows that the presence of dust has minimal influence on the image stitching process but shows significant negative effects on the visualization of geologic feature and lithology change. In addition, the presence of water can significantly hinder the image stitching process, which in turn helps in identifying lithology change. Borehole scoping aids in identifying and mitigating hazardous conditions in underground mines, and this study provides preliminary inputs into identifying optimum borehole conditions for geologic mapping with panoramic borehole images.

Feb 1, 2025

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025

By Jacob Mathis, Mark Bradford, Alston Noronha, R. M. True

In June 2022, Louisville MSD completed a 6.5-km (4.0-mi), 6.1-m (20-ft.) diameter CSO conveyance and storage tunnel system located along the Ohio River in downtown Louisville, Kentucky. For large diameter shaft and tunnel construction, drill-and-blast operations among other methodologies were used in close proximity to federal, commercial, and residential properties with no impact to stakeholder infrastructure. s one of the rst maor tunneling proects in Louisvilles metropolitan area, this paper explores Black & Veatchs rigorous geotechnical instrumentation monitoring program that provided uality assurance for local stakeholders and afrmed innovative tunneling solutions can be successfully executed in an urban setting.

Jun 23, 2024