Search Documents

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By R. J. Sawyer

The Greens Creek underground polymetallic mine restarted production in 1996 from a newly discovered high grade ore zone. Efforts to improve payable gold recovery have focused on gravity separation. The paper compares testwork and plant results for a newly installed gravity circuit.

Jan 1, 1997

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

By Gilman Y. Murray

The problems connected with the development of economically acceptable water supplies in arid regions are discussed. The techniques for capture and retention of runoff from infrequent desert storms are described and the major factors involved are emphasized. The exploration and planning for a typical water development in southwest United States is described, including an analysis of capital and operating costs for the proposed system.

Jan 1, 1963

By D. G. Chedgy

Environmental improvement efforts are focusing with increasing intensity on pollutants resulting from combustion. The high cost of removing these pollutants at the power station is well documented. Physical coal cleaning has always been and should remain the most economic method of reducing sulfur oxide emission from coal combustion. It is critical in the selection of preparation plant circuitry to consider capital and operating costs, as well as the level of sulfur reduction. This paper describes the technical criteria which must be used for efficient process selection and summarizes the cleaning systems available or in development.

Jan 1, 1990

By Richard W. Amerman

The final cost and quality of a project employing equipment, labor, and materials is dependent upon the expediency and extent to which each of these parameters are used. An ideal solution then, would be one in which three solvable equations were given for each particular situation. The equipment, labor, and materials could then be solved for, and the perfect job would result. In reality, however, the ideal and most economical solution is seldom attainable by solving three given equations. Therefore, knowledge, experience, and sometimes guesswork must be relied upon when correlating equipment, labor, and materials. Drilling and blasting, in particular, is one operation which normally involves more uncertainty than other operations. It is also an operation in which the outcome is extremely critical for two reasons. First, the cost of the operation that follows drilling and blasting is dependent upon how well the material is fragmented. Second, once the drilling and blasting has taken place, it is impossible to return to the area, without considerable expense, and correct any mistakes that might have been made. Therefore, what is desired is a method by which drilling and blasting operations can be performed yielding optimum results at the lowest cost; this can best be accomplished by having the relationships between equipment, labor, and materials prior to their use. For obtaining best results, the selection of these three relationships must be based on knowledge, experience, and as little guesswork and uncertainty as possible.

Jan 1, 1969

Growing concerns of climate change and its potential association with the release of greenhouse gasses to the atmosphere have prompted possible legislation which would require minimization of greenhouse gas emissions. Carbon dioxide and methane, both of which largely contribute to the greenhouse effect, have direct links to the fossil energy industry sector. Specifically, the combustion of one ton of coal produces between one and three tons of carbon dioxide, dependent upon the carbon content and heating value of the combusted coal. Additionally, coal mine methane (CMM) released through a mine?s ventilation system has a radiative trapping impact approximately 20 times greater than that of an equivalent mass of carbon dioxide. The capture of coalbed methane (CBM) prior to the mining process and its utilization as an alternative energy source provides the possibility of a decreased carbon footprint. Domestically, the past 25 years have seen a significant expansion of the CBM industry. Internationally, in developing countries such as China, the need for western coal degasification technology is growing. A collaborative, international effort will be required to initiate a recognizable decrease in global greenhouse gas emissions. This paper identifies the potential decrease in equivalent carbon dioxide emissions through effective degasification at a hypothetical longwall mine located in China. Advanced, three-dimensional gas reservoir simulation software will be utilized to determine the maximum feasible CBM recovery in a low permeability, high gas content reservoir prior to the mining process.

Jan 1, 2010

By Donald G. Dahle

Project Payette is a conceptual nuclear experiment under the Vela Uniform program intended to further evaluate the mechanism of seismic decoupling. Vela Uniform is a Department of Defense program to improve this country's capability to detect, locate and identify underground nuclear detonations. This program evolved from recommendations of the Panel on Seismic Improve¬ment, (Berkner Panel), an officially appointed group of noted U. S. scientists. This Panel, taking note of difficulties in detecting the differences between some underground nuclear detonations and some earthquakes recommended a program of increased basic research in seismology. The theory of decoupling, Which involves possible reducing of seismic motion resulting from underground explosions by reducing the coupling or physical linkage between the explosion and the geologic environment, was investigated by Dr. Albert latter and his associates at RAND during the late 1950's. The concept has been further investigated theoretically by scientists of the Lawrence Radiation Laboratory and the Sandia Laboratory. The theory has been tested experimentally under Vela Uniform Projects Cowboy, Dribble and Sterling. The Salmon Event of Project Dribble was a tamped (with the explosive in firm contact with the geologic formation) nuclear detonation 2700 feet below ground in the Tatum Salt Dome. Project Payette, if found to be feasible and if authorized for actual execution, would become a decoupled experiment in the same environment.

Jan 1, 1968

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

By Mike Lewis

"Descending several stories down a metal staircase into a shaft spanning a quarter city block -- soon to become Roosevelt Light Rail Station in Seattle, WA -- visitors are greeted with four perfectly round, precast concrete-lined horizontal holes leading deep into the earth. The sound of water trickling out from a small drainage trough can be heard over the faint echoes of construction within. Upon entering, the light is dim, but the air is clear with barely a dust particle flowing through the sunbeams. This type of air quality is only accomplished with diligent controls, and JCM Northlink, the company in charge of building the Northgate Link Extension Project, is taking those measures seriously.Commissioned by Sound Transit, JCM is a joint venture of three companies: Jay Dee Contractors, Frank Coluccio Construction Co. and Michels Corp. The tunnels JCM constructed are intended to provide fast, reliable underground rail service, as well as relieve one of the region’s most congested traffic areas. The $440 million project will connect the Northgate, Roosevelt and University District neighborhoods north of Seattle to the downtown corridor and SeaTac airport further south.The scope of this project includes excavation for two light rail stations, boring of two parallel 5 km- (3.3-mile) long light rail tunnels in six runs and the construction of 23 cross passages. Begun in 2014, Sound Transit estimates that crews excavated more than 382,000 m3 (500,000 cu yds) of soil and installed 7,352 precast concrete tunnel liner rings during the shaft construction and boring phase. Now that tunnel boring is complete, JCM is in the process of constructing the cross passages, which act as maintenance areas and escape routes for passengers. Throughout the entire process, the company has utilized atomized mist to control particle emissions.“Our dust control needs change at every phase of the project and don’t go away until the project is fully complete,” said a JCM safety representative. “We found that different dust suppression technologies were needed at different intervals, but atomized mist seemed to fulfill our needs at every step.”"

Jan 9, 2017

By Jr. Chesson

"Phosphate" is a misnomer as often used. The word is increasingly used to refer to any material containing phosphorus - an element essential to any form of life. Phosphate rock, a mineral - fluorapitate - is recovered from Florida's sedimentary deposits in particle sires ranging from 0.1 to 13.0 millimeter. This product of mining, washing, screening, and flotation is commonly called "phosphate". Its phosphorus content, measured and reported as P2O5, varies from 29% to 35%, and is essentially insoluble. "Phosphate" is also used to describe products containing soluble phosphorus obtained from acidulation of phosphate rock with mineral acids; primarily, sulfuric acid. Many miners have nearby chemical plants wherein phosphate rock is converted into upgraded products such as phosphoric acid, superphosohates, and ammonium phosphates with 45% to 70% P205, soluble and suitable for use as fertilizer. The rock and upgraded products are all commonly called "phosphate"; the plants, "phosphate plants' and the producers collectively are known as the "phosphate industry". The public in Central Florida generally loses identification of the individual operators that include major corporations such as IMC. Williams Companies, W.R. Grace, Mobil, Embark, U.S. Steel, Borden, American Cyanamid and others. They all become just a "phosphate company".

Jan 1, 1978

By Olivier Martin

In busy and historic cities, traditional open box metro stations are becoming outrageously difficult, unacceptable for the citizen and uneconomical. Hybrid stations provide an interesting alternative. In-house experience of Gautrain (South Africa), West bay (Qatar), Cairo line 3A (Egypt), and Melbourne (Australia) all aim to reduce disturbance to the city and its inhabitants during construction. Constructed in rock or in deep soil under water table, they take advantages of the latest construction techniques from cement grouting to freezing, and from traditional excavation of cavern to large tunnels constructed by sophisticated tunnel boring machines (TBM). Today, they form the ultimate construction challenge.

Jun 13, 2021

By Doug Harding

The Metropolitan St. Louis Water District’s Project Clear is a 28-year program targeting wastewater capacity throughout St. Louis, MO. The extensive program includes the Jefferson Barracks Tunnel, running parallel to the Mississippi River at 2 m ID and 5,400 m long. A rebuilt Robbins Main Beam TBM began boring but hit challenging conditions about 2,400 m in, including water inflows. A larger 4.1 m Robbins Main Beam machine will complete the remaining 3,050 m in limestone, dolomite, and shale. The TBM will utilize a high-powered, high breakout torque cutterhead along with enhanced 360-degree probing & grouting capabilities to detect any karst formations.

Dec 1, 2022

By M. G. Schulz

Mining of molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock-types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the ore body. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1985

By H. Mischo, F. Daniela, L. Schaarschmidt, I. Paschke

In order to safely store radioactive waste long-term, HAW repositories in saliferous formations have to be backfilled. The main purpose of those backfill operations is the restoration of the geological barrier function of the containment area. For best possible results the used material should be of a comparable composition or characteristic for the host rock formation. Additionally, the material should show a high density after completion of the backfilling process as well as a low permeability. A major aspect to consider in these processes is the minimization of the gap of the backfill body to the roof of the drift. To fulfil those requirements, a micro-structure stabilized crushed salt backfill material has been developed as part of the GESAV-I-project. Due to the material composition of this so-called GESAV-material, salt mineralcrystallization processes start after emplacing it, a process that leads to the polyhalite formation. With the crystallization of polyhalit, the halite grains are bridged, which in return stabilizes the matrix of the backfill. The GESAV-II-project continued successfully what GESAV-I started and determined an ideal backfill method in order to build the backfill bodies composed of GESAV-material. Due to the compaction of the material during emplacement by vibration, high in-situ densities, low permeabilities and a backfill factor close to 1 was able to be reached. In the following SAVER project this journey of practical test underground will be continued.

Mar 2, 2022

By Jorge Ferrero, Andreas Raedle, Uhland Konrad, Michael Dutton, Keivan Pak Iman, Walter Trisi

Strabag, in partnership with Arup, is constructing the Advance Tunnel for the Scarborough Subway Extension (ATSSE); a project by Metrolinx and Infrastructure Ontario (Sponsors). The 10.7 m internal diameter single bore tunnel represents a significant departure from the traditional arrangement of twin subway tunnels in North America. ATSSE is the first-time steel fibers are used to solely reinforce a tunnel of this size in Eastern Canada. This paper discusses the challenges with design and acceptance of SFRC segments and the state-of-the-art numerical models employed to check the joint performance. The advance procurement approach for TBM and PCTL’s procurement to accelerate the project schedule is also presented.

Jun 13, 2023

By Matthew Holden, Jason Emery, Matthew Benjamin, Peter Craig

Over the last 25 years, through adversity and a growing level of risk mitigation, Australian Longwall mines have been using higher and higher capacity cable bolts for secondary support. A recent survey revealed 85% of Australian longwall cable bolts are a 70 tonne capacity pre-tensioned hollow post groutable system. Mines avoiding pumping cementitious grouts are sometimes using pre-tensioned resin encapsulated solid cable bolts of over 90 tonne capacity. Results from various industry and University research has led to manufacturer's fine tuning the construction of their cable bolts. A review of this research explains how smooth wire construction is now dominant. Aggressive shear has also led to some mines using 8 tonnes pre-tension instead of the previous common 20 tonnes pre-tension. Lower pre-tension acceptance is now leading to a greater use of threaded cable bolt end fittings, these are tensioned to 8 tonne using the drill motor torque. A recent development is the TEX cable bolt, a slim line threaded end fitting that fits with the drill hole like a standard rock bolt. This cable is being installed at the coal face as primary support off bolter-miners. The laboratory and in-situ testing of the TEX cable is presented. In a bid to improve gateroad development rates and ground support in the last several years, a 100 tonne tensile capacity Goliath cable system was developed. The latest development in resin anchored solid cables is a 110 tonne capacity cable bolt, with laboratory and in-situ testing results presented.

Jun 25, 2024

By Paul C. Schmall, Thomas Tuozzolo, Arthur B. Corwin

The Lenox Avenue Reconstruction Project involved the excavation and replacement of 750 m (2,500 ft) of deteriorated subway invert concrete, 5 to 7 m (15 to20 ft) below water table in very permeable ground. The Replacement work was done over an 8 month period, while maintaining track service through this subway section. The project was dewatered with a single 125 l/s (2,000 gpm) wellpoint system,750 m (2,500 ft) in length, which was installed from inside the active tunnel structure and configured to coexist in the subway tunnel with operating trains as well as the construction activities. A thin diaphragm jet grout wall was utilized on one end of the site to cut off the flow of water across a difficult geological interface that was situated immediately below the tunnel invert. The thin diaphragm jet grout wall permitted the large 116th Street Station area to be dewatered completely with well points from outside of the excavation.

Jan 1, 2001

By E. M. Williams

The U.S. Bureau of Mines recently conducted a limited-scope study on the use of lineament analysis and electromagnetic geophysics to better identify the surface expressions of faults at the Cimmaron Mine near Raton, NM, an operating longwall mine in the York Canyon mine complex. Two normal faults were encountered by the mine, one during gate road development and drilling and another only through drilling. The potential ground control problems and offsets associated with these faults will severely impact long-range development plans, so it is essential to know the lateral extent of these faults within the coal reserves. The surface topography at the site is fairly rugged, yet outcrop exposure is poor. There is no obvious visible geologic evidence to indicate that the faults identified at depth extend to the surface. Both the geophysical and remote sensing techniques provided information on the presence and extent of important geologic structures which could not be gained just from drilling and surface outcrops. The geophysical surveys also were invaluable in confirming the presence of subsurface geologic structures in the vicinity of the lineaments assumed to be associated with the faulting.

Jan 1, 1995

By I. Y. Bausov, L. G. Stolarczyk, R. E. Pillmore, A. J. Hillard, J. T. Duncan

"Prevalence of lung disease in younger miners surprised industry regulators, congressional members, researchers and black lung clinic staff members. Mitigation researcher focused on low-coal mining in the Appalachian regions until Miners Colfax Medical Center (MCMC) Black Lung Clinic examinations discovered 25 of 72 Wyoming coal miners with lung disease. To reverse recent upward trend in lung disease, research programatic have been directed at reducing exposure to respirable “float” dust. This paper suggests broadening the scope of research to include boundary detection in efforts to improve outcomes. Beginning with a better understanding of biochemistry of anaerobic bacteria methylation processes precipitating sulfur and heavy metals into thin seam boundary layers. Expanding research and development objective to focused on minimization of bit-pick crushing cone volume and preventing mining thin boundary coal layers and out-of-seam dilution. Black lung clinical evaluations of miner will confirm outcomes directed towards reduced occupational disease and smoke stack emissions. INTRODUCTION Miner exposer to bit-tip crushing cone volume, fragmentation and auger movement generated respirable “float” dust and boiler emissions are related science-technology –engineering-mathematics (STEM) problems. Formidable but not intractable problems are driven by oxidation of upper flood plain elements in the periodic table and biochemical metabolic presses occurring in coal basin. Because of burial compaction, quartz and trace heavy metals (Fe2+, Mg2+) are concentrated in thin seam boundary layers. By not cutting through thin boundary coal layer and out-of-seam into hard quartz containing rock layers, miner lung disease and smoke stack emissions are minimized. Cutting bit-pick elastic wave hydrodynamic principle force vectors in the coal layer must be aligned to minimize respirable dust generation, constrained by fragmentation size. Dust abatement by water spray and machine design are effective; but for, failure to address cutting cone dust volume generation and its distribution along run-of-mine (ROM) transportation systems the boiler. Real-time precision thickness measurements by integrated cutting drum (icDrum) sensor, machine man-interdiction from a dust free control room, is a cost effective way to prevents respirable dust exposure. The recommended STEM research and demonstration initiative addresses issues raised by discoveries of increased rate of lung disease discovered in young miners and concerns over emissions from coal-fired electric generation stations (Global Warming). In-mine demonstrations must be validated by on-site MCMC mobile Black Lung Clinic data acquisition and analysis."

Jan 1, 2016