Search Documents

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By J. M. Pugliese

The U.S. Bureau of Mines is developing designs and estimating costs for vertical in situ copper mining wells as part of its in situ mining research program. Conceptual designs and estimated costs for "deep" 1100 m (3600 ft) recovery and injection wells in an undisturbed copper ore zone are presented. Within a single in situ copper mining well, multiple perforated well completions and associated costs are discussed for two ore zones between depths of 370 m (1200 ft) and 550 m (1800 ft). The order of well specifications for designing these wells is explained.

Jan 1, 1995

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By K. E. Harrison

Acid rain legislation as proposed by President Bush [1], if enacted, will immediately refocus current thinking on the economic decision-making as related to coal preparation facilities. Unit operations currently ignored because of their costs, will become mandatory to coal plant designers and operators to ensure maximum energy recovery and sulfur reduction in the entire coal stream. In anticipation of this need, the U.S. Department of Energy, The Ohio Coal Development Office, EPRI and others are sponsoring research in several areas of coal preparation, and coal plant designers are beginning to consider more innovative techniques as they configure their flowsheets for plants of the future. Preparation plants then will have recleaning

Jan 1, 1990

By Sadegh Elyasi

TBMand roadheader are two dominating excavation machines in underground tunnelling projects. The performance of these two tunnelling machines has been reviewed and analysed individually by many researchers from multiple points of view. However, there are almost no studies that have made an extensive comparison between these two machines, mostly from financial points of view. The current study is intended to characterize both financial and technical status of these two mechanical tunnelling machines in one of the biggest coal mines in Iran. The main objective of this study is to define the best method and equipment that meets a predefined economic goal, which is mainly to maximize the net present value. To this end, a technical and financial model based on the geomechanical and financial parameters involved in the project has been prepared and the financial part of the project has been carried out by applying COMFAR III financial analysis software. Subsequently, a sensitivity analysis of the model was conducted in order to evaluate the effect of involved parameters on the project. According to the results, a roadheader has better economic justification than a TBM, while the TBM has a better advance rate than the roadheader.

Feb 12, 2021

By SHANTAE LEE, ELAHEH TALEBI, Frank A. Drews, W. Pratt Rogers

Fatigue in mining operations is a serious issue and a significant contributor to incidents and accidents. While mine operators are using or introducing new technology to monitor operator fatigue, there is little work that focuses on the subjective experience of fatigue and the use of fatigue monitoring technology. To investigate this issue, eight focus groups with a total of 44 operators of heavy haulage equipment working for two mining companies in the Mountain West of the USA participated in 1-h focus groups. The topic of the focus groups was the experience of operator fatigue and issues surrounding fatigue at the workplace. The results of the content analyses suggest that operators are well aware of the signs of fatigue, and that they understand the severity of these signs as well. In addition, they are aware of the effect of fatigue on driving performance and are using a wide range of methods to manage fatigue. Finally, based on participants’ assessment, current fatigue monitoring systems lack face validity and reliability and are perceived as not being effective. The results of this study emphasize the importance of a socio-technical systems perspective in the context of miner health and safety management. Only such a comprehensive perspective can result in improvements that are sustainable.

Jun 17, 2020

By John Newby, Ulf Gwildis, Ken Massé, Guillaume Roux

How to connect an effluent conveyance tunnel to riser shaft and diffuser arms of an outfall system is dictated by the ground conditions, which ideally include rock or soil strata of low permeability. Where such favorable conditions are beyond reach, both the complexity of designing and the risk of constructing this crucial system connection increase disproportionally. This paper describes the considerations that went into the approach of connecting a 5-m-diameter TBM drive with the in-river riser shaft of the Annacis Island WWTP New Outfall System in the highly permeable Fraser River sands at hydrostatic pressures exceeding 3 bar.

Jun 23, 2024

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

In underground continuous mining operations, ventilation, water sprays and machine-mounted flooded-bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements — such as face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation and equipment operator positioning — can have impacts on the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Pittsburgh Mining Research Division for remotecontrolled continuous mining machine operators as well as haulage operators at 10 U.S. underground mines. The results of these respirable dust surveys show that continuous miner exposures varied little with depth of cut but are significantly higher with exhaust ventilation. Haulage operators experienced elevated concentrations with blowing face ventilation. Elevated dust concentrations were observed for both continuous miner operators and haulage operators when working in crosscuts driven into or counter to the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposures attributable to particular mining configurations. These findings form the basis for recommendations for lowering face worker respirable dust exposures.

Jan 1, 2016

By Andrew Stafford, Kate Willa Brown Requist, Eric Lutz, Simon Lotero Lopez, Moe Momayez, Jeffrey Gordon

This formal literature review identifies strengths and shortcomings of current literature related to mine rescue, self-rescue, and self-escape technology. Key concepts and factors that influence the decision making behind mine rescue and self-escape were identified. Historically, underground mining has been one of the most dangerous occupations due to the harsh nature of working environments. During the latter half of the twentieth century, and into the twenty-first century, mining fatalities have declined, yet large-scale mine emergencies persist. The emergence of new technologies, in combination with evidencebased mine emergency research, is resulting in new training methods, monitoring systems, and self-escape approaches being tried in operating mines. This review identifies areas in which substantial research is being conducted, such as the use of virtual reality and game-based training and areas that warrant further development such as the measurement and information gathering capabilities of unmanned ground and aerial vehicles, as well as emergency management and incident command systems. This paper summarizes the current underground mine rescue and self-escape landscape in the USA, including the breadth and depth of mine rescue and self-escape training and practices as evident in the literature.

Nov 2, 2023

By Samuel S. M. Chan

Rock surrounding mine openings frequently is an impermeable type such as shale or granite. Most rock, however, has joints, bedding planes, cleavage planes, or other potential discontinuities. Permeability to fluids (gas or liquid) may exist via natural joints or fractures in an otherwise impermeable rock. In the mining situation, tectonic and induced tensile and shear stresses may be great enough to cause joints to open or fractures to develop in previously solid rock. The rock, as a result, becomes less self-supporting and may - require artificial support such as rock bolts or timber. Simultaneously, as fractures develop, permeable paths may be created. If fluid can be injected into a previously solid and impermeable rock mass, a logical conclusion is that a fracture (crack) flow path must be transmitting that fluid. The U.S. Bureau of Mines Laramie (Wyo) Energy Research Center has been evaluating results of in-situ oil shale fracturing (hydraulic or explosive) and retorting experiments by. a fluid (air) injection , and borehole air flow profile logging technique since 1956 (1, 14, 15). In the oil shale case, it is imperative to know the location and flow capacity (permeability) of natural fractures, if they exist, and induced fractures that inter-connect vertical wellbores at depths of fifty to several hundred feet. By injecting air into one wellbore in a system of several wells and measuring input volume and pressure while simultaneously measuring the output of other wellbores, the minimum areal extent of interconnecting permeable fractures can be determined. Exact locations (depths) of fractures and individual fracture flow capacities between wellbores can be determined by air flow profile logging (14, 15). Knowledge of fracture locations and permeability is essential to rational experimental in-situ retorting design.

Jan 1, 1973

By Andrew Hall

Many Latin American countries are facing a scarcity of water. As such, infrastructure decisions are quite different from those made in parts of the world that experience a positive water balance. In the latter case, the water treatment approach tends to be ?treat and discharge.? For Latin American regions facing the challenges that go with a negative water balance, the focus is on resource optimization and reuse. Historically, the water challenge has had a significant impact on economic development in Latin America, especially in sectors such as mining, where water usage is high. At the same time, countries such as Chile and Brazil are major development targets for mining and oil and gas operations. Given the water supply challenge, industry is increasingly turning to technologies and processes that maximize water recovery and reuse. With sulfide precipitation and ion exchange water treatment processes for example, it is possible to treat and recover more than 99 percent of water for reuse onsite. These technologies have been applied successfully in other regions of the world where water conservation practices are essential to economic survival.

Jan 1, 2012

By Roger Storry, Arnaud Hochart, David Harris, Olivier Martin

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands under the main shipping channel in Biscayne Bay. Five cross passages (CPs), spaced at 200m centre to centre, provide emergency access between the two tunnels, as shown in Figure 1.The CPs were constructed by open-face excavation methods but the particular geological conditions at the project site (loose and variable carbonate sedimentary strata with very high permeability) required specific ground treatment solutions to provide safe excavation conditions and to ensure the long term serviceability of the permanent works construction. Where access allowed, ground treatment was performed from the ground surface using deep-mixing techniques; however, at two locations (CP2 and CP3) surface access was restricted and ground treatment by freezing, performed from the tunnels, was required. The CPs are 12.3m long with an excavation diameter of 5.8m and are located up to 30m below the water table partly or wholly within the Key Largo limestone (termed Layer S7 in the ground model). Layer S7 is a coralline limestone having a metastable honeycomb structure and high variable porosity. At CP2 the upper portion of the excavation was within the overlying Anastasia Formation limestone (Layer S6), comprising a highly permeable coquina. The geological profile along the project is shown in Figure 2.This paper presents aspects of the freeze design and the risk mitigation necessary to successfully achieve the construction of the CPs in the unique geological conditions."

Jan 1, 2016

By K. M. Reim

Planning the development of the Quartz Hill molybdenum open pit mine in Southeast Alaska required a number of special considerations. Located in mountainous glaciated terrain, about 3.8 m (150 in.) of annual precipitation (with annual snowfall over 10.2 m (400 :in.) was a primary consideration. Mine planning included muskeg and snow removal, avalanche control, clearing timber, water quality control, dust control, seismicity, mine schedule, work force and reclamation. Quartz Hill is in an environmentally sensitive area which has required extensive environmental baseline data collection, four Environmental Impact statements (EIS) and a large number of permits.

Jan 1, 1988

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The rare earth element (REE) industry has sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive concentrations. These deposits are extremely uncommon, particularly in the United States. Given the criticality of these materials and the need for a sustainable domestic supply, the current research seeks to leverage the generation and treatment of acid mine drainage (AMD) as an autogenous process that can lead to concentrated REE resources. 

By Takuya Tani, Tomoyuki Aoki, Kazuo Saskai

"The authors have proposed a unique methodology in the evaluation of rock mass stiffness for the range of five to twenty meters ahead of the tunnel face, with the use of small diameter inclinometers. The inclinometers are installed at the tunnel crown at a pre-determined constant interval, about one meter behind the face in order to obtain the slight change in inclination angles during tunnel excavation. This method was developed as a daily control measurement such that the geological condition and its possible change ahead of the face could be detected early by monitoring the trend of inclination angles. This paper describes the results of the ground stiffness ahead of the tunnel face evaluated at a mountain tunnel construction site. This stiffness is evaluated automatically and displayed visually by the current system equipped with a result display screen, together with a warning message against a weak zone when detected. 1. INTRODUCTION In a conventional planning of a mountain tunnel, according to the Japanese Standard (JSCE, 2006) seismic refraction surveys from the ground surface are performed and tunnel support patterns are then designed based on the seismic wave velocity. The resolution of the velocity profile estimated by this technique, however, is poor as the tunnel overburden becomes large. The tunnel face is therefore often encountered by unforeseeable fault zones or weak rocks. Such an unpredictable weak zone occasionally causes the collapse of the tunnel face. Clarifying the forward geological information during excavation is hence significant for safe and well-controlled construction. According to the geological conditions ahead of a face, auxiliary methods typified by forepiling and face bolting could be preliminarily prepared for prompt execution. For the purpose of acquiring forward geological information, pilot borehole drilling and seismic reflection methods represented by the TSP (Tunnel Seismic Prediction) or HSP (Horizontal Seismic Profiling) are often applied. Those exploration are carried out near the tunnel face for a couple of days. This often leads to the interruption of excavation procedure and has no small effect on the construction schedule. On the other hand, some forward ground prediction methods in the daily control measurement have been developed e.g. by Schubert et al. (1995). In this method, tunnel displacements in the direction of the tunnel axis are used together with the crown settlements. We have tested their method at a few of our tunnel projects and found difficulty in the evaluation of the forward ground condition due to insufficient resolution of the axial displacement measured by a total station theodolite that we usually use for the tunnel measurement. We have therefore developed a novel methodology of monitoring slight inclination at the tunnel crown near the face, so that the forward ground conditions can be predicted and evaluated as part of a routine measurement procedure."

Jan 1, 2016

By Kazmierczak J. B., Klein E., Kinscher J., Lizeur A., De Santis F.

In this work, we propose to implement machine learning methods for the automatic classification of mining-related seismic data. The approach retained for the classification is based on a Convolutional Neural Network (CNN) which has been tested and applied to two different mining datasets: the active ore mine of Garpenberg (Sweden), currently under exploitation, and the abandoned coal mine of Gardanne (France), where mining stopped in 2003. The first step of the approach consists in creating a well classified (manually) database of seismic signals separated in different classes as a function of the seismic sources. The selected database is then divided into two groups: train, containing the 70% of the signals, and test, which contains the remaining 30% of the signals within the selected database. The learning phase of the algorithm consists in creating a classification model based on the train group, which is further validated on the test group. The application of CNN for the automatic classification of Garpenberg and Gardanne seismic data shows, respectively, that about 88% and 98% of the seismic events of the two sites can be properly classified. These results demonstrate that machine learning could be a powerful tool for microseismic monitoring in mining and post-mining environments, which could be further extended to the whole automatic processing of seismic data, including signal’s classification as well as microseismic event’s localization.

Apr 26, 2022

By A. Fleming

The exploration process, like any other commercial activity, can only succeed if the objective of the exercise is clearly defined and persistently pursued. Successful exploration requires properties, funding, personnel and persistence. Many of us have years of experience in conducting exploration in our countries of residence. Conducting exploration in a foreign country, however, requires a number of significant other criteria.

Jan 1, 1997

By Mollie Hunt, William Riley, Russ Downer, Kate Willa Brown Requist, Víctor O. Tenorio, Geoffrey Gill

One of the first activities after returning to the Moon will be finding sources of water and materials for the construction of human settlements and other infrastructure. There is evidence of the existence of deposits in the bottom of craters at the South Polar region and in flat areas around. Based on geological data from the Moon, a block model representing a deposit or icy regolith has been defined in the vicinities of Shackleton Crater, with unique characteristics of shape, thickness, and water contents. A mine plan utilizing surface mine modeling software for ore extraction from an open pit- type of excavation to a delivery point near a water processing facility is proposed, with monthly, quarterly, and yearly schedules. Production results, dashboard charts and progress of the topographic changes are also presented.

Feb 1, 2024

"INTRODUCTION The characterization of groundwater hydrogeology is a common component in feasibility studies, geotechnical investigations and regulatory permitting for mining operations. The lithology at a location of interest may include several discrete water-bearing units; and the means of isolating each for testing can be accomplished through the use of inflatable packers. Consideration for testing during drilling program planning and communication between all stakeholders is essential to ensure that the Mine, Drilling Contractor and Hydrogeological Testing Specialist (Specialist) are ready to perform packer testing when the call is made to mobilize. Often, the notice to mobilize can be delayed and then occur with little warning due to the issues that can occur during drilling of very deep boreholes, as well as other factors. Hydrogeological investigation reports and journal articles generally discuss testing methods and results, with limited information available describing the planning and coordination of the field testing program, as evidenced by the lack of references cited below. The source of inspiration for the subject matter of this paper is grounded in the author’s past shortsightedness; with the hope that others not share similar misfortunes but experience success through thorough preparation for their future hydrogeological testing programs. The sections below focus on the planning stages of a field investigation using inflatable packers, including considerations for site specific conditions, designation of stakeholder responsibilities, and communication of testing expectations. Following these sections is a presentation of two examples of successful field programs and lessons learned in addressing problems encountered along the way. PRELIMINARY PROGRAM PLANNING & CONSIDERATIONS From the onset of planning for drilling programs, the Specialist should be in communication with the Mine to review plans and identify fatal flaws which could impede collection of hydrogeological data. Preliminary scope decisions can significantly affect the budget and duration of hydrogeological field programs and may dictate the means by which the field data is collected. The issues that need to be considered include the following factors. Testing Objectives The setup of the packer tool is dependent on the testing objectives. Is the goal to estimate bulk aquifer hydraulic conductivity or to identify discrete discontinuity hydraulic characteristics? Are groundwater samples needed? The answers to these questions affect selection of test interval length and what instrumentation might need to piggyback on the packer tool. Identifying the testing goals initially will provide adequate time to prepare packer equipment for mobilization. Borehole Size While inflatable packers come in many shapes and sizes, some sizes are more readily available and easier to procure on short notice. Packers for NQ and HQ size boreholes have been historically easy to procure and are commonly used in exploration drilling. Packer equipment is available for smaller holes, but it becomes more difficult to fit instrumentation down-hole as the borehole size decreases. This is particularly a consideration if collection of groundwater samples is required. In addition, risks of losing the hole or equipment downhole are greater for smaller boreholes. Larger boreholes require larger packers and clearly require more effort and heavier capacity machinery to manually manipulate due to the increased size."

Jan 1, 2017

By Todd Wanless, Daryl Poduska, Prakash Donde, Mahmood Khwaja

"The proposed Minne Lusa Stormwater Conveyance Sewer is part of the Phase 3 Major Combined Sewer Overflow projects to be scheduled as part of the City of Omaha’s Long Term Control Plan (LTCP). The system features a 6,100 foot long, 14-foot inside diameter tunnel to provide for conveyance of separated stormwater from previously completed and future LTCP sewer separation projects to the expanded Storz West and Pershing Detention Basins and subsequently, the Missouri River. The tunnel will operate as a pressurized system and convey flows of up to 2,500 ft3/s resulting from a 10-year, 24 hour storm event. This paper provides a synopsis of the project with a focus on the overall design aspects related to siting the tunnel alignment in an urban environment, the hydraulic analyses performed to choose a pressurized system rather than an open channel system, and expected geologic conditions. Tunnel alignment and profile and geological profile are presented, as well as an overview of the construction related impacts considered during design. PROJECT BACKGROUND The proposed Minne Lusa Stormwater (MLSW) Conveyance System will provide for conveyance of separated stormwater from previously completed, and future, LTCP sewer separation projects to the expanded Storz West and Pershing Detention Basins and subsequently, the Missouri River. The project location is representatively shown on Figure 1; the overall conveyance system is represented in Figure 2. The MLSW Conveyance System consists of three separate construction contracts under Contract Numbers: OPW-52004 – The Storz West Detention Basin to 31st & Paxton Tunnel; OPW-52454 – The Storz West/Pershing Detention Basin Grading and Improvements; and, OPW-52752 – The Pershing Detention Basin to ML Outfall Channel. This paper focuses on the project covered under Contract OPW-52004: design and construction of an approximately 6,110 feet 14-foot inside diameter (ID) tunnel, constructed using a Tunnel Boring Machine (TBM). The tunnel will receive flows from the Paxton Boulevard (PB) and the John Creighton Boulevard (JCB) Stormwater Conveyance Sewers and convey the flows to the Storz West Detention Basin, resulting in CSO volume and flow rate reductions to the Minne Lusa Outfall Channel and the North Interceptor."

Jan 1, 2016