Search Documents

By Ernest W. Hilton

The purpose of this investigation was to assess the environmental impact of the surface mining methods currently used in the steep-sloped areas of Central Appalachia: southern West Virginia, eastern Kentucky, southwestern Virginia and northeastern Tennessee. Comparisons are made between mountaintop/cross ridge mining, contour strip, augering and an innovative method surface shortwall mining which was attempted at Julian, West Virginia. Included in this final report are a discussion and analysis of current Appalachian production, reserves, and the extent of land affected on a county- by-county basis. Additionally, the seams within the steep sloped region have been assessed according to minimal standards of thickness, surrounding lithology, and areal extent to determine their amenability to surface shortwall mining. These seams have been tabulated with their ash, sulfur, and BTU content on a county-by county basis. Only minimal statements are made concerning quantity because of the narrow set of conditions required by the shortwall method. Other sections deal with the possible technical failings of an operational surface shortwall system based on field studies at shortwall operations, discussions with people experienced with shortwalls and research into ground control problems at sites where short- and longwall operations have been monitored. A final section details proposed additional research directions which the Bureau might take in the future.

Jan 1, 1979

By Mark Colwell, Russell Frith

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a chain pillar design methodology readily usable by colliery staff. The project was primarily funded by the Australian Coal Association Research Program and further supported by several Australian longwall operations. The starting point or basis of the project was the Analysis of Longwall Pillar Stability (ALPS) methodology. ALPS was chosen because of its operational focus; it uses tailgate performance as the determining chain pillar design criterion rather than simply pillar stability. Furthermore, ALPS recognizes that several geotechnical and design factors, including (but not limited to) chain pillar stability, affect that performance. There are some geotechnical and mine layout differences between United States and Australian coal fields that required investigation and, therefore, calibration before the full benefits offered by the ALPS methodology could be realized in Australia. Ultimately, case history data were collected from 19 longwall mines representing approximately 60% of all Australian longwall operations. In addition, six monitoring sites incorporated an array of hydraulic stress cells to measure the change in vertical stress throughout the various phases of the longwall extraction cycle. The sites also incorporated extensometers to monitor roof and rib performance in response to the retreating longwallface. The study found strong relationships between the tailgate stability factor, the Coal Mine Roof Rating, and the installed level of primary support. The final outcome of the project is a chain pillar design methodology called Analysis of Longwall Tailgate Serviceability (ALTS). Guidelines for using ALTS are provided.

Jan 5, 1999

By Launa Mallett, Charles Vaught, Michael J. Bmick

Since 1991 the Pittsburgh Research Center (PRC formerly part of the U. S. Bureau of Mines) has been tapping u valuable resource-researchers have recorded extensive interviews will, 30 individuals who are recognized as experts in the area of mine emergency response. These veterans related stories and observations from events experienced during as many as 47 years of response activities. Overall, the response veterans averaged 29 years of mine emergency response experience and 35 years mining experience. Individuals [ ] interviewed included representatives from mining companies, the UMWA and state and federal government agencies. This information was gathered so dial it could he provided to today's miners and to tomorrow's emergency response personnel. It is hoped the collective wisdom that has been obtained can be used to help train new responders and guide those decisions which mill have to be made on the scenes of future events. During interviews file emergency response experts were asked to discuss lessons they had learned through experience. The interviewers asked them to tell what they had learned that would cause them to handle similar situations differently and to tell about things they saw at past events shat the would warn others not to do in the future. In response the experts discussed a variety of things. Most of their responses, however, touched on some of the same topics including: preparedness, experience people on-site mine rescue teams, and decision making. A summary of their responses provides alt overview of [lie lessons learned on-site at tile largest mine disasters in the country.

By Robert S. Hedin

Passive methods of treating mine water use chemical and biological processes that decrease metal concentrations and neutralize acidity. Compared with conventional chemical treatment, passive methods generally require more land area, but use less costly reagents and require less operational attention and maintenance. Currently, three types of passive technologies exist: aerobic wetlands, organic substrate wetlands, and anoxic limestone drains. Aerobic wetlands promote mixed oxidation and hydrolysis reactions, and are most effective when the raw mine water is net alkaline. Organic substrate wetlands promote anaerobic bacterial activity that results in the precipitation of metal sulfides and the generation of bicarbonate alkalinity. Anoxic limestone drains generate bicarbonate alkalinity and can be useful for the pretreatment of mine water before it flows into a wetland. Rates of metal and acidity removal for passive systems have been developed empirically by the U.S. Bureau of Mines. Aerobic wetlands remove Fe and Mn from alkaline water at rates of 10-20 and 0.5- 1.0 g. m-2? d-1, respectively. Wetlands with a composted organic substrate remove acidity from mine water at rates of 3-9 g. m-2? d-1?. A model for the design and sizing of passive treatment systems is presented in this report.

Jan 1, 1994

By R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 2010

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By James P. Ludwig

This report provides the results of a two year study of the projected time and cost requirements for new mine development in Wisconsin and is based on a unique blend of information from mining company officials, state regulatory agency officials and contractor experience. Through formal cooperative and review agreements with Kennecott Copy per Corporation, Exxon Minerals Co., U.S.A. and Noranda Mines Ltd., and the Wisconsin Department of Natural Resources plus informal arrangements with knowledgeable Wisconsin persons, lists of the tasks and subtasks required to plan a new mine in Wisconsin were developed. Times and costs were assigned to all tasks and subtasks and these data reviewed by all cooperators. Critical Path Method Diagrams were then developed for a generalized mining project. Total time and cost for the premine planning process was estimated to be 25..1 years and 223 person-years of professional time excluding public affairs effort respectively. By eliminating redundancies in the process and by increasing project efficiency through early public review and participation, recom¬mendations were made to lessen the time and lower the cost of premine planning. The streamlining recommendations could shorten the overall critical path length to 18.16 years and lower the cost to 208 person-years of professional time excluding public affairs effort. The estimated distribution of professional effort (cost) for mine planning in Wisconsin approximates 50.5% for traditional mine engineering tasks, 36.6% for environmental-regulatory tasks and 12.9% for traditional geological-exploration tasks.

Jan 1, 1979

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state regulatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

Five watersheds, ranging in size from 29 to 49 acres, were selected in East-Central Ohio to investigate the hydrologic and water quality conditions occurring before, during, and after surface mining. Four of the watersheds will undergo surface mining, involving either the Number 6, 9, 11, or 8 coal seams, and one watershed having an outcrop of the Number 6 coal will be operated as a control watershed. To determine the premining hydrologic and water quality conditions (Phase 1), physical information was obtained for each watershed and instrumentation was installed for obtaining hydrologic data and water quality samples. In addition to topographic maps, soils and vegetation maps were prepared. Stratigraphic columns were developed from geologic cores; networks of observation wells and of soil moisture access tubes were installed; and weather stations were established to measure temperature, humidity, wind and solar radiation, and to collect precipi¬tation samples. Field data were collected over a 10-month period for one watershed and for about 8 months on another watershed before surface mining began. The other watersheds continued in the premining data phase. These data were for precipitation, temperature, relative humidity, wind speed, solar radiation, snow and frozen soil, soil moisture, infiltration (rainfall simulator), spring discharge, runoff from watersheds, and ground-water levels. Also, samples of runoff and ground water were obtained for chemical analyses and additional samples of runoff were acquired for suspended sediment load determinations. Over the study period, precipitation was not very representative of the long term averages, but data are available from the control watershed for a representative 7 year period which should prove invaluable in modeling the hydrology of the project watersheds for the premined conditions. Spring discharges (before mining) from the upper aquifer of two of the watersheds averaged only 508 and 652 gallons daily. The proportion of precipitation occurring as surface runoff from the large watersheds ranged from 8 to 36 percent and the peak discharges from 5.86 to 81.95 cfs. Base-flow and runoff water samples from four of the watersheds (unmined conditions) were collected and analyzed quantitatively for 39 water quality parameters. Monthly precipitation samples sediment fractions of the base flow and runoff were analyzed for 22 and 17 parameters, respectively. The average concentrations of the water quality parameters for the watersheds (unmined), except for suspended solids, were as low or lower than the EPA recommended maximum allowable concentrations in drinking water. Several parameters in precipitation equaled or exceeded the levels of corresponding parameters in runoff water. The average concentration of suspended solids in storm runoff ranged from 118 to 1110 mg/l, and for base flow the range was from 44 to 247 mg/l; the higher concentrations were associated with the watersheds exhibiting the greatest disturbance. Iron ranged from an average of less than 3 µg/1 to 228 µg/1. Manganese ranged from less than 41 µg/1 to 334 µg/I. Ground-water systems (unmined condition) are described for the five project watersheds. Each watershed was found to have two major perched aquifers within the top 250 feet. Generally, these perched aquifers involve local flow systems, though flow across watershed boundaries in some areas. Recharge is mostly from local precipitation and discharge is mostly as spring flow, base flow, evapotranspiration, and leakage through the underlying confining bed. Shallow ground water was commonly of the calcium bicarbonate type. Although dissolved-solids concentration was generally 200 to 600 mg/1, brackish or salty ground water was present in several areas. A composite hydrologic model for the project watersheds will consist of separate ground-water, unsaturated flow, overland flow, and evapotranspiration component models. The ground-water model (a modified quasi-three--dimensional U. S. Geological Survey model) operates on a grid network and the newly formulated unsaturated flow model was divided into overlying prismatic elements for numerical solutions. The unsaturated flow model includes provision for incorporating the evapotranspiration model. An available distributed kinemetic overland flow model was utilized. An analyses was made of one of the costs of reclaiming coal mines; the legal and administrative costs of complying with legislation. Such costs borne by coal companies under the Ohio law are thought to be a surrogate of these costs under the new Federal law. Regression analyses were used to relate the legal and administrative costs to acres in the permit and the tonnage of coal produced.

Jan 1, 1978

By Gregory J. Chekan

The Bureau of Mines, in an effort to improve planning and development in coal mining, is investigating strata interactions associated with mining of multiple coalbeds. Two common interactions that occur between adjacent coalbeds are subsidence and pillar load transfer. The study described involves underground observations and measurements conducted at two Pennsylvania mines, each affected by one of these interactions. At the mine affected by subsidence, measurements show that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. At the mine affected by pillar load transfer, Initial in situ measurements have shown the existence of a pressure arch in the lower workings. Prior research has shown that arch interaction between two adjacent openings can create stress concentrations in the in-nerburden. Underground measurements and results obtained from both mine sites correlate with theoretical and photoelastic multiple-seam models, and eventually these field data will serve to refine model accuracy. Further study of multiple-seam interaction mechanisms will lead to improved mine planning, increased resource conservation, and a safer working environment.

Jan 1, 1986

By Jerry T. McLendon

The proper disposition of phosphatic clays has been the subject of research and debated for years by phosphate producers, State and Federal research agencies, regulatory authorities, and environmentalists. To date, no "universal" solution exists for the ultimate disposl of phosphatic clays. This Bureau of Mines report examines the state of conventional clay disposal technology and reviews the technical progress of innovative alternatives. Twenty impoundment sites were investigated by the Bureau of Mines using geotechnical methods and laboratory analysis of cored samples. In addition, quasi-static cone penetrometer soundings were conducted to define clay and/or sand-clay interfaces en masse. Samples of the top, middle, and bottom hole segments were obtained at each station for laboratory studies of clay densities, pore fluids, plasticity, and mineralogical properties. The results of this study support the continued use of initial clay settling impoundments but emphasize the need for "in-line" systems to reduce the initial volumes of plant-generated phosphatic clays. The effective use of sand tailings is also encouraged to promote further consolidation of clays via self-weight stressing, sand-clay admixtures, and/or surcharging sand caps.

Jan 1, 1984

By Grant Buma

Groundwater restoration is an uranium leaching. Information on the technology, costs, and the current permitting regulations is of vital operators and to firms considering in important aspect of in situ effectiveness of the current state and federal government importance to in situ leach situ leaching. This study, funded by the U. S. Bureau of Mines, describes: (1) all recent restoration attempts at commercial in situ leach operations, (2) restoration costs reported by the industry, (3) empirical equations that predict the amount of groundwater flushing required to meet the current restoration criteria, and (4) in situ uranium permit requirements for the states of Texas, Wyoming, New Mexico, Utah, Montana, Colorado and South Dakota, and Federal requirements.

Jan 1, 1981

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system or systems, thus disclosed. Of the several systems initially investigated and evaluated, four Showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By Jr. Denton

This U.S. Bureau of Mines report presents the documentation for HEAPREC, a methodology for calculating reclamation performance bonds for cyanide heap leach operations. HEAPREC is a template developed for use with Lotus 1-2-33 release 2.01 or newer software. The report is presented in step-by-step "user's manual" format. Appendices contain detailed background and reference material on performance bonding, cyanide detoxification regulation, cyanide detoxification methods, general mine reclamation procedures, and an example bond calculation.

Jan 1, 1992

By J. K. Whyatt

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [s 1 ?135 MPa (19,600 psi) oriented S 80° W). An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 2010

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide alumina production capacity by plant and country. The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1993. Capacity data represent announced installed and planned capacities and do not necessarily reflect a Bureau of Mines judgment of actual plant operating levels or timing of planned expansions, The year-end capacity is the ?nameplate" capacity or estimated production capacity, whichever is larger.

Jan 1, 1993

By Verne E. Hooker

The Bureau of Mines conducted a preliminary investigation to determine the state of stress in crystalline rock outcrops near Atlanta, Ga. The secondary principal stresses in a horizontal plane near the surface are compressive and are 500 to 3,000 psi. The maximum compressive stress is northeast-southwest in the Stone Mountain-Lithonia district but changes to northwest-southeast near Douglasville. The elastic constants were determined from data obtained by static and dynamic laboratory methods and in situ velocity measurements. Results show Young's modulus to be dependent upon both stress level and anisotropy in the rock. Average secant moduli obtained from triaxial tests were used to compute the applied stress from borehole deformation measurements.

Jan 1, 1966

By T. E. Ackman

Scale inhibitors and slow-release polymers were tested by the Bureau of Mines at mine drainage treatment facilities. The scale inhibitors were investigated to determine their effectiveness in controlling gypsum (CaSO4) scale; the polymers were investigated to determine their effectiveness for increasing settling rates of suspended iron hydroxide. Two types of scale inhibitors were tested at a site having a severe CaSO4 scaling problem. Both proved to be effective in controlling scale formation; in addition, one caused the dissolution of CaSO4 deposits. Slow-release polymers were tested at three mine drainage treatment facilities. These gelatinous polymeric flocculants were found to be convenient and easy to use, but only effective when pH could be controlled.

Jan 1, 1984

By Robert M. Cox

The U. S. Bureau of Mines (USBM) MULSIM/NL modeling technique has been used to analyze anticipated stress distributions for a proposed alternative longwall gate road design for a western Colorado coal mine. The model analyses indicated that the alternative gate road design would reduce stresses in the tailgate entry without increasing stresses in the headgate entry. To test the validity of the alternative gate road design under actual mining conditions, a test section of the alternative system was incorporated into a subsequent set of gate roads developed at the mine. The alternative gate road test section was instrumented with borehole pressure cells, as part of an ongoing USBM research project, to monitor ground pressure changes as longwall mining progressed. During the excavation of the adjacent longwall panels, the behavior of the alternative gate road system was monitored continuously using the USBM computer-assisted Ground Control Management System. During these field tests, the alternative gate road system was first monitored and evaluated as a headgate, and later monitored and evaluated as a tailgate. The results of the field tests confirmed the validity of using the MULSIM/NL modeling technique to evaluate mine designs.

Jan 1, 2010