Search Documents

By Marcel Bielefeld, Joost Bakker, Rob van Dorp

Pile load testing can be performed by a static, rapid or high strain dynamic (generally designated as dynamic) testing method. The static load test is often considered the “gold standard” of testing with the other methods merely ‘alternatives’. However, the rapid load test, as a quasi-static test, has all the positive elements of the static alternative: the direct measurement of loads and displacements. Moreover as stress wave phenomena have no influence, the interpretation of rapid load test results is more straightforward than that of dynamic testing, and also independent of the person performing the interpretation. This paper will explore the Rapid Load Testing method and illustrate the advantages and limitations through a case study in Rostock, Germany

May 1, 2022

By Michael Gebman, Jack Gerwick

"With the opening of the new San Francisco-Oakland Bay Bridge East Span, the former bridge and its caisson foundations are being demolished. Caisson foundations are in the path of a future shipping channel and therefore need removal down to the mudline 50 ft below water (MLLW). For the first caisson to be removed (E3) a mechanical demolition was performed above the waterline and an implosion was done for the remaining caisson down to mudline. Mechanical demolition consisted of excavators operating from either on top of the caisson, from work platforms or from barges. The demolition was implemented on a trial basis with a successful implosion on November 14, 2015. The work was conducted in an environmentally sensitive area, with measures taken to protect fish, marine mammals and birds. This demolition technique was cost effective, faster to execute, and had a better environmental impact then an alternative option. The demolition, measures implemented to protect the environment, outcome, and lessons learned are presented.INTRODUCTIONThe California Department of Transportation needed a cost effective and environmentally friendly solution for removal of the remaining San Francisco-Oakland Bay Bridge (former East Span) caisson foundations, starting with caisson E3. This was necessary to clear a future shipping channel. One option was to construct a steel cofferdam around the caisson to allow demolition in the dry down to the mudline. This option would take years to complete, be cost prohibitive, and its noise would disrupt aquatic life and birds throughout the cofferdam construction and demolition. An alternative option was implemented on a trial basis to conduct a mechanical demolition of the caisson above waterline along with an implosion of the remaining caisson down to mudline. This had the clear advantage as a cofferdam was not needed, and the demolition project duration would be approximately 6 months, instead of several years for the cofferdam option. The potential impact on aquatic life and birds from the implosion was a concern, as the location is environmentally sensitive; however, measures were implemented to minimize these impacts. As presented in this paper, this demolition option was implemented on a trial basis for Caisson E3. The technique succeeded and will now be used on the remaining caissons.BACKGROUND INFO ON CAISSON E3The reinforced concrete Caisson E3 is the largest caisson which supported the former East Span of the Bay Bridge. It was constructed in 1934, with the Bay Bridge opening in 1936. Figure 1 shows the project location. The caisson had a cell arrangement of 7 x 2 above the mudline. Below mudline, the caisson had a cell arrangement of 9 x 4. A structural transition was made between the 7 x 2 and 9 x 4 cell arrangements with buttress walls. All cells were flooded, as underwater openings were included in the original caisson walls to equalize the hydrostatic pressure. Figure 2 shows the caisson layout with limits for mechanical demolition and for the implosion."

Jan 1, 2016

By A. V. Rose

A redevelopment in the City of London has been constructed with a piled foundation system that is believed to be the first of its kind. The purpose of the research is to explore this novel foundation method, which involves the installation of closely spaced piles in a perimeter arrangement with a body of soil enclosed in the centre. Both centrifuge modelling and numerical modelling techniques are used.

Jan 1, 2011

By Waddah Akili

The demand on pile installation in the offshore of the Arabian Gulf has, over the last two decades, experienced unprecedented boom, triggered by the construction of platforms, to help facilitate the production and transport of oil and gas. Available borehole data show that ground conditions for pile installation in the offshore is highly variable, resulting in misassessment of insitu conditions, leading to a huge discrepancy between ultimate pile capacities, based on design, and actual capacities after installation. The paper makes use of pile installation records derived from several platforms in the offshore of the state of Qatar, the Gulf Region. More specifically, the paper evaluates “as–installed” ultimate capacities and safety factors, recommends remedial installation procedures, and proposes a means for determining pile acceptability for piles meeting refusal short of design penetration. The paper offers what is believed to be relevant recommendations to guide the design and installation of future offshore structures; enabling the geotechnical community in the Region to solve their current offshore pile installation problems and gain an added margin of confidence regarding the ultimate capacity of installed piles.

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By Terzis D. PhD, Katterbach M.

While awareness around the environmental impact of existing grout materials and chemical binders is increasing rapidly, biotechnologies are growing traction as sustainable alternatives in groundwork operations. Herein we present the principles and application methods of bio-grouting. The term is used to describe a system which is based on soil, groundwater or marine enzymes which are able to catalyze the production of calcite replicating a natural phenomenon. The system’s end result are mineral crystalline bridges which act as binders to improve the geotechnical properties of soils. This paper presents a comprehensive description of bio-grouts, their underlaying mechanisms contributing to mineralization as well as environmental considerations. With their water-like rheology, bio-grouts have a wide application range and are minimally invasive, requiring only very limited injection pressures. The equipment is the same as that used in conventional cement grouting, and the reactant components are worldwide available or easily suppliable, which explains why bio-grouting has nowadays become a valuable and sustainable alternative towards efficient soil treatment. Recent developments in the last years have allowed to further increase the applicability and efficiency of bio-grouts to ultimately bridge the gap between research and practice. A case study is illustrated in this paper showing the successful implementation of bio-grout for the stabilization of weakly cemented sandstone to safeguard an adjacent road segment in Switzerland

May 1, 2022

By Bengt H. Fellenius

.1.1 Prior to commencement of pile installation operation, submit to [Engineer] for [approval] [review], details of equipment for installation of piles. SPEC NOTE: The information requested in 3.1 .1.2 is necessary as input to a detailed wave equation analysis of the pile driving. .1.2 For impact hammers, give manufacturer's name, type, maximum rated energy and rated energy per blow at normal working rate during easy and at termination driving, mass of striking parts of hammer, mass of driving cap, and type and elastic properties of hammer cushion. .1.3 For non-impact methods of installation, such as drilling, jacking, jetting, use of vibratory hammers, or other means, give full details of characteristics necessary to evaluate performance. .2 Impact Hammer SPEC NOTE: Do not exclude a hammer type unless for very specific reason. .2.1 [Drop hammers will not be permitted.] [Diesel hammers will not be permitted.] For final driving of [TYPE] piles, provide a hammer capable of delivering to the pile a non-erratic impact stress not smaller than [VALUE] Pascal and transferring a non-erratic energy not smaller than [VALUE] Joules per blow to the pile head at normal working rate.

Jan 1, 1991

By Suthan Pooranampillai

This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By A. Bozorgzadeh, B. M. Jensen, B. N. Koelling, B. R. Murtaugh

"The Service Base mooring system originally consisted of two general types of structures, 19 timber piles cabled together and steel three-legged pipe piles. The St. Louis District fleet moored to the fleet barges which were tied off to shore-side concrete deadman and supported on the landward side by the timber and steel piles. The purpose of this project was to replace the existing floating wharf mooring system at the St. Louis Service Base. The Marine Design Center of the U.S. Corps of Engineers developed a three pile cluster system concept. The clusters consisted of one vertical pile and two batter piles. Piles in rock sockets were selected to resist the uplift loads due to high wind loads on the tall, spare lock gates stored at the floating wharf. This paper focuses on the design of the rock sockets for steel pipe piles with large uplift loads and the lessons learned during the design and construction of this system.INTRODUCTIONBackgroundThe U.S. Army Corps of Engineers’ St. Louis District is located at the critical transition point on the Mississippi River where it is a “locking river” north of St. Louis and an “open river” to the south. The St. Louis District is responsible for maintaining navigation channels on the Mississippi River, the Illinois River and the Kaskaskia River. It is also responsible for the operation and maintenance of five locks and dams within its geographic boundaries.The St. Louis District utilizes a fleet of vessels (dredges, crane barges, motor vessels, and barges) to support the navigation mission identified above. The St. Louis District Service Base, located in St. Louis, Missouri, serves as the base of operations for the district fleet. This riverfront facility originally consisted of a floating wharf, a railroad trestle, and a walkway down the river bank to the floating wharf. Historically, there have been two fleeting areas at the Service Base. The main fleeting area was approximately 965 feet long and consisted of six fleet barges (Figure 1). This area supported the Dredge Potter and its attendant fleet. The upper fleeting area was approximately 1,050 feet long and consisted of various stop log, crane and work barges, dredge pipe pontoons and work flats."

Jan 1, 2017

By Clifford Taylor, Alexander Zöhrer

"The execution of deep basement excavations under narrow conditions is one of the most challenging tasks in geotechnics. The vicinity of neighbouring buildings, roads, and underground structures such as sewers or power lines, quite often prohibits the application of standard solutions. In addition, legal considerations in the use of adjacent properties is becoming increasingly difficult. This paper will present some innovative approaches to overcome the above-mentioned challenges based on several case studies from central Europe. For every project the design approach as well as the techniques used for execution will be explained, detailing both the advantages and the limitations of the applications. One case study shows a deep basement excavation (approx. 17m) in the centre of Prague, Czech Republic. This project featured many challenging boundary conditions (narrow construction area, high ground water table, jet grouting column embedment into bedrock, constraints regarding use of ground anchors due to property rights, etc). The realisation of the complex design is described and illustrated in detail. Other case studies will show the combined application of bored piles with jet grouting and also explain the design of vertical prestressed anchors for retaining walls.INTRODUCTIONThe development of urban areas has always presented challenges, from access for equipment and materials to the rectification of existing foundations in unknown condition. Compounding these is the increasingly stringent requirements to retain, maintain and reduce impact on culturally and historically significant structures. As available space is becoming more limited, optimisation of real estate has resulted in buildings getting higher and their basements deeper below ground. Two or more basement levels are quite common, with typical excavation depths ranging from 5 to more than 10m. Additionally, we are faced with neighbouring buildings that are equally high, deep and massive. These buildings directly adjacent the retaining structure require underpinning to limit settlement, and in cases where they are within just a few meters, this building mass generates additional earth pressure for the retaining wall to support, resulting in complex loading cases.This paper highlights several common challenges and explores the measures implemented to overcome them. The challenges and examples of either design based solutions or practical applications will focus on the following topics – the limitations of conventional geotechnical construction methods, overcoming challenging geology and the requirement for watertight basement constructions."

Jan 1, 1900

By Chetan D. Savani, Mike K. Muchard

The necessity to evaluate undocumented foundation lengths is essential in assessing the useable life, need for scour protection, retrofitting, or full reuse of existing bridge foundations. For this purpose, Parallel Seismic Testing (PST) has the best accuracy and is applicable to the widest range of foundation configurations used in bridge construction of any test method. Although not limited to bridges, PST case studies are presented involving two bridges. To preface the case study discussions, an overview of the PST method is given along with its results and analysis thereof. In one of the cases, we were afforded the rare opportunity to see the existing piles being extracted long after the PST testing program was completed. The resulting Class A prediction reaffirms the accuracy of the method. Versatility of the PST method is also exemplified in the two cases presented, where unique situations from complex foundation systems were overcome by analysis to provide successful results.

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.IntroductionCement deep soil mixing (CDSM) was used as a replacement for stone column ground improvement in a corridor which the owner, the Washington State Department of Transportation (WSDOT) wanted to reserve for future trenchless crossings beneath reinforced soil embankments within a freeway interchange. The work was part of HOV improvements to I-5 in Tacoma, Washington. The CDSM construction occurred in late 2010 and early 2011.Approximately 14,500 cubic yards of soil cement columns were placed by CDSM. The soil cement improved ground supports permanent geosynthetic reinforced slopes up to 50 feet high. The ground improvement was designed primarily to provide global stability of the reinforced slopes during seismic loading, but it was also utilized to reduce the time and total amount of settlement following construction of the embankments.This paper presents a discussion of the design approach and challenges associated with quality assurance of a relatively small volume of CDSM within the time constraints of an ongoing project. The challenges associated with attempts at collecting cores of the cured soil-cement mix cured by triple tube coring and pushing a double tube into the wet mix and allowing it to cure insitu are discussed, along with the eventual adoption of sonic coring combined with reliance on laboratory testing of wet mix samples collected daily."

Jan 1, 2017

By Jason Buenker, Molly Winston

Torque-installed piles are gaining popularity in Southern California as the go-to deep foundation element for small- to medium-capacity loads in urban environments. The torque-installed pile is a displacement- based screwed pipe pile with a closed-end conical tip welded to the bottom of the pipe. Torque-installed piles are most efficient in loose to medium dense soils with high liquefaction potential. Where used properly, torque-installed piles can be installed faster, require less clean-up, and create less onsite vibration/disturbance than other pile alternatives. However, torque-installed piles are not applicable in all soil conditions and care must be used to apply the pile effectively in the correct subsurface environment. This paper will review current Southern California state-of-the-practice for torque-installed pile design and construction, potential roadblocks to successful installation, and available capacities from load tests. INTRODUCTION Torque-installed piles are a type of full-displacement screwed pipe pile originally developed in Southern California circa 2001 by Substructure Support, Inc. The pile is unique for its proprietary closed-end conical tip shown in Fig. 1. The tip has a welded steel-helix plate and cutter teeth that allow the pile to be advanced efficiently under applied torque and down pressure (crowd). Since original development of the pile, several contractors or manufacturers have proposed similar proprietary screw-type piles with comparable conical tips. Pile installation is relatively quiet, vibration-free, does not generate spoils, and faster than comparable pile types. The pile was originally developed as an alternative to driven pile foundations and remains a critical substitute to driven foundations in urban environments. Torque-installed piles are conventionally specified as 12 ¾-inch outside diameter (OD) steel pipes with a ⅜-inch-thick wall, although larger sizes with alternative dimensions have been used outside Southern California. Pile installation lengths generally range from 30 to 50 feet but may reach 80 feet or greater where soil conditions permit. The pile is generally backfilled with concrete following installation to increase lateral pile stiffness and may incorporate rebar cages or other reinforcing steel to facilitate connections to structural elements. The pile is frequently specified using performance-based specifications that encourage contractor innovation and use of proprietary installation means and methods.

Jan 1, 2019

By Karen Talbot, Noah Maier, Rob Jameson, Giuseppe Gaspari

A storage and drainage tunnel advancing below I-75 in Detroit, Michigan experienced sudden subsidence. The Tunnel Boring Machine (TBM) was damaged to the extent that its shield, cutting head and extensive interior components needed to be extracted and replaced along with several completed tunnel segments. The tunnel was 16 feet (4.9m) in diameter with crown over 79 feet (24m) deep at the time. The tunneling contractor immediately engaged their designers and specialty subcontractors to develop a scheme to access the machine and repair the tunnel. They required a shaft 99 feet (30m) deep, with unobstructed plan dimension of 50 feet (15m) to accommodate the large components that needed to be removed and replaced. This precluded the application of an internally braced excavation and instead earth support solutions focused on use of a compression ring. Since the completed tunnel section behind the TBM obstructed closure of the compression ring below its invert, this paper describes the innovative access shaft solution employed. A conventional compression ring was constructed using 5 feet (1.5m) diameter drilled shafts down to the tunnel crown. In front of, and to the sides of the tunnel heading, the secant shafts were extended to over 150 feet (46m) depth, creating a horseshoe of support extending 50 feet (15m) below the planned excavation invert. Larger diameter "King Pile" shafts were drilled immediately to either side of the tunnel, overlapped into each end of the secant "horseshoe". The king pile shafts, together with a heavily reinforced ring beam above the crown elevation, acted as a door frame to transfer hoop loads from the incomplete secant arc into reaction supports above and below the tunnel. These oversize king pile shafts were extended and socketed into rock over 70 feet (21m) below tunnel invert. Very tight installation tolerances were necessary to maintain secant shaft alignment to depths exceeding 150 feet (46m). The project operational, geotechnical, and quality data was managed and visualized using a custom GIS interface. This paper will present the design approach employed and review the construction and quality program selected to repair the tunnel.

Oct 1, 2022

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By William B. Conway

This paper will describe the large caisson pier foundations for four of the bridges crossing the Mississippi River in the New Orleans area; and will discuss some of the unusual problems encountered during their sinking. Certain settlement phenomena experienced during their service life will also be related: The four bridges in order of their construction: The Huey P. Long Bridge, River Mile 106.1, completed in 1935 The Greater New Orleans Bridge No.1, River Mile 96.0, completed in 1958 The Hale Boggs Bridge, River Mile 121.6, completed in 1983 The Greater New Orleans Bridge No.2, River Mile 96.1, completed in 1988 Each of these bridges employed large open-dredged concrete caissons as foundations for one or more of the river piers, with the smallest being the 65ft by 102ft caissons for Piers I and II of the Huey P. Long Bridge and the largest being the 99ft by 214ft caisson for Pier II of the Greater New Orleans Bridge No.2. The Huey P. Long caissons are founded in a dense fine sand at -170 while all of the other bridge caissons are founded in hard preconsolidated clay at elevations varying from -150 to -185. The Huey P. Long Bridge is currently being widened without increasing the caisson foundations under any of the river piers; and the design reasoning that led to this decision is presented.

May 11, 2007

By Marc Raithel, Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments and dikes on soft soils was introduced some 20 years ago and is now considered State-of-the-art in Germany, Europe and, step by step, worldwide. The GECs consist of compacted non-cohesive granular fill similar e.g. to common gravel columns with one decisive difference: they are confined in a high-strength, high-modulus, flexible geotextile “cylinder” (encasement). This engineered element with parameters being adaptable in a wide range provides a decisive tool to control and optimize the behavior of the GEC foundation system. Consequently, the GECs work properly even in extremely soft soils, and a wide range of fills inclusive of sands can be used. In the meantime vast design and technological experience is available and codified design methods exist. Initially the paper briefly describes the general idea, the basics and specifics of design, construction technology, materials, restrictions and optimal application areas. Then it focuses on three informative case studies. They are briefly presented focusing for brevity only on the most important facts and experience inclusive of the most meaningful data of short- and long-term measurement programs.INTRODUCTIONWhen considering embankments on soft soils, generally two groups of solutions exist:Unsupported embankments; there are four main options:a) build up embankment extremely slowly waiting for sufficient consolidation after every stage;b) replace the soft soil partially or totally;c) install a high-strength basal reinforcement providing overall and local stability and allowing much faster embankment construction;d) combine c) with strip drains to accelerate consolidation and thus the construction process additionally (Fig. 1, left).Today, practically only option ""d"" is of practical relevance. Despite all the pros and cons, the common attribute of all non-supported options is that local and overall stability (Ultimate Limit State-ULS) can be achieved and controlled, but not the short- and long-term settlements (Serviceability Limit State-SLS). The latter can be significant, e.g. up to 30% of the nominal planned embankment height. Supported embankments (Fig. 1, right): the main common idea is to over-bridge the soft soil layers by supporting vertical elements of different types: rigid piles, trench walls etc. or by ""softer"" solutions of different column types (compacted, cemented, mixed-in-place etc.). Herein the borderlines between “piles”, ""pile-similar elements"" and ""soil improvement” are fluent and depend on country, traditions, codes etc. The common attribute of the “supported” schemes is a minimized settlement. Twenty years ago a new specific solution was launched: the Geotextile Encased Columns (GEC), which is discussed in more detail below."

Jan 1, 2017

By Adrian Gygax, Sarah Gaib, Rod Kostaschuk

The British Columbia Ministry of Transportation and Infrastructure (Ministry) recently completed a slope stabilization project at Ten Mile Slide on Highway 99. The highway is an essential part of the road network connecting the British Columbia (BC) coast with the interior of the province. The landslide was first identified in the mid-1980s and has retrogressed more than 250 m upslope since then, leading to continual and expensive repairs to the highway. The Ministry engaged BGC Engineering Ltd. (BGC) and their structural sub-consultant Gygax Engineering Associates Ltd. (GEA) to develop a stabilization scheme that would halt the slide with an acceptable level of residual risk. The design required careful consideration of construction stages and the stresses induced in the structural components as the slide movement was progressively stopped as construction advanced. Four stabilization design options were shortlisted with the preferred option selected in Fall 2016. The selected solution comprised the construction of five rows of post-tensioned soil anchors upslope of the highway and a tied-back concrete tangent pile retaining wall for the roadway itself as well as reconstruction of the highway alignment, grade and drainage through the slide. Works were installed by top-down construction within defined time allowances stipulated in the contract. Significant engineering was undertaken beyond standard design processes for this complex project, such as comprehensive geotechnical investigations, aerial and terrestrial laser scanning and change detection analyses, pre-production test anchors, detailed geo-structural numerical modelling and due diligence activities to validate and optimize the design. The stabilization works have been very successful with the slide response being as predicted and the highway operating again as full two-lane service.

Oct 1, 2022

By Kevin Cunningham

"Litigation resulting from neighboring structures with settlement and/or lateral movement or improper pile design and faulty soils engineering analysis, are a multi-faceted opportunity for law firms. These types of claim scenarios are an attorney’s dream, and can obliterate a Deep Foundation Contractors profit and more importantly, can be avoided with a progressive approach to risk management in design and project management.The following (4) case studies will be examined and dissected to discern certain lessons learned for risk management solutions to avoid these deep foundation related challenges in the future.1) Pipe Flotation – Soil Conditions Not Anticipated in Specifications or Contract2) Easement Encroachment – Easement Dimensions Not Recognized Until Completion of Project3) Subjacent Lateral Support – Neighboring Structure Wooden Pile Unprotected Causing Structure to Settle4) Improper Pile Placement - Construction & Design Caused Retail Store to SettleSpecific Deep Foundation project challenges involving: buoyancy calculations regarding subsurface soil characteristics, design factors taking existing subsurface sewer line easements into account, structural instability as result of excavation causing exposure/heavy rainfall to existing wooden piles supporting adjoining building and improper pile location resulting from faulty pile design will be described with risk management recommendations to avoid these challenges in the future.From the very start of construction on any project deep foundation and excavating work poses numerous engineering and technical challenges for developers, contractors and engineers. Dealing with changing or hidden conditions is one of the most difficult challenges facing any contractor or engineer on a project. Relying on incomplete or inaccurate engineering reports is another common problem. Other challenges include dealing with technical errors or oversights that are deeply embedded in the project specifications or bid process.No matter what is the origin of the problem or how it manifests, deep foundation contractors, design professionals and engineers should be ever-mindful of good risk management practices that can prevent serious disputes that can result in costly litigation."

Jan 1, 2015