Search Documents

By C. M. Badeen, J. Paige, W. Evans, L. McCauley, A. Caddies, I. Alilovic, R. Turcotte, C. O. Lyogun, C. Bonner

Gear pumps are very commonly used for the pumping of AN-water based emulsion products for both handling and blast loading applications. The potential major hazardous problems likely to be encountered with these pumps are: (i) high probability of friction; (ii) possibility of product confinement in the area of the bushings; (iii); high bearing failure rate; (iv) pump running dry; (v) presence of foreign material; (vi) deadheading of pump; (vii) delamination of elastomer from steel gears. Of all these possible scenarios, the no-flow situations where the pump is running dry or deadheaded have always been recognized as the most serious ones.

Jan 1, 2015

By E. L. McHugh, J. M. Girard

This paper discusses the results of two recent case studies in which high-tech prototype instruments were used. The first case study describes the results of a ground-based hyperspectral imaging tool used to map the geology of an open-pit mine highwall. The second case study outlines the use of interferometric synthetic aperture radar and how this type of radar can be used in a variety of geotechnical situations. These case studies are part of an on-going research project at the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory. The project objective is to implement engineering controls and design methods in order to reduce the number of injuries and fatalities associated with slope failures at mining operations. Project personnel are hopeful that these new developments in technology will lead to better geotechnical monitoring and design in slope stability and other important areas of rock mechanics.

By F. Baerhold, S. Mitterecker

"Acid recovery is an important process step in pickling and leaching processes. Pyrohydrolysis in spray roasters and fluidized beds is a well-established technology to recover hydrochloric acid, but the hydrolysis in the liquid phase is more and more considered as an alternative new process route. The characteristic features of these three processes will be discussed along with select industry trends. For example, hydrochloric acid based leaching processes for ilmenite and nickel laterite ores produce far larger volumes of waste acid streams than the steel industry. Scaling-up of the spray roasting technology to the highest possible capacity is necessary in order to become more cost effective. In addition, process routes based on ferric chloride pyrohydrolysis allow the production of super-azeotropic HCl (up to 30 wt.%). Finally, the new ECOmode concept optimizes the operation of both pickling lines and the spray roast acid recovery plant. Long term results from industrial applications show that fuel savings in the spray roaster of 25% are easily achieved without additional process steps. An attractive feature is also to upgrade existing installations to higher plant capacities.INTRODUCTION Pyrohydrolysis is the conversion of metal halides into metal oxides at elevated temperatures in the presence of water vapor. Reaction products are a hydrogen halide gas and a metal oxide. The process was originally developed and introduced into the market by ANDRITZ Ruthner in the 1960’s. It has found wide technical application in the field of acid recovery and oxide production. The introduction of this process has revolutionized pickling technology. The use of hydrochloric acid has strongly increased over the last decades, since pyrohydrolysis is available for the total recovery of waste pickle liquors from mild steel pickling, as illustrated in Figure 1.Chloride media are also used increasingly in the metallurgical industry. Oxide production processes for Mg, Co, Ni, and Al have been installed. Processes using hydrochloric acid are known for the leaching of ores as well as for the re-extraction of metals from organic solvents. In both cases the recycling of HCl is of substantial importance to achieve highly economic processes and to reduce waste."

Jan 1, 2016

By Kristen E. Coose

Concrete is a mixture of a fine aggregate (sand), a coarse aggregate (gravel), cement, and water. Cement itself is the most expensive of the ingredients but generally amounts to only about 10% of the concrete mixture. Cement raw materials include calcium, alumina, iron oxide, silica, and gypsum. They are heated and chemically changed into clinker "minerals," which are then ground and shipped as cement. Each of the four main clinker minerals-tricalcium silicate, dicalcium silicate, tricalcium aluminate, and tetracalcium aluminoferrite-impart specific strength and compositional properties to the final concrete product. During hydration of the cement, chemical changes produce new minerals that include calcium silicate hydrate gel (C-S-H, the main constituent of hydrated cement paste), calcium hydroxide, and calcium, sodium, potassium, and sulfate ions, among others. Two main reactions can occur that may be deleterious to concrete. Normal cement pore solutions, in a hydrated cement, contain sodium hydroxide and potassium hydroxide. If these alkali concentrations are too high, they can react with the siliceous aggregate (alkali-silica reaction, or ASR) to form an alkali-rich calcium silicate hydrate gel (C-N+K-S-H), which, upon prolonged contact with water, can expand to crack the concrete. The other deleterious reaction occurs when the mineral ettringite (Ca6A12(S04)3OH12. 26H20) forms after the concrete is hardened (delayed ettringite formation) and cracks the concrete. Many of the concrete bridges and structures built in New Mexico in the past 20 years are in need of replacement due to deterioration. Many others constructed very early on in the century are still sound. By collecting and analyzing samples of both old and new concrete and good and bad concrete, we compared their differences on both a microscopic and macroscopic scale. Samples taken from concrete sidewalks, parking lots, drainage canals, spillways, and a railroad-trestle foundation have construction dates that range from 1923 to 1997. They were analyzed by electron microprobe and by petrographic microscopy. Cracks, air voids, and aggregate alteration were primary locations for investigation and analysis. Using the electron microprobe, ettringite was found in voids of most of the samples, both in good and bad concrete. This leads us to believe that ettringite formation is not causing distress in the concrete. There was one exception in which ettringite was found lining a crack. In this instance, ettringite may have the ability to further the cracking and cause distress. No alkali-silica gel was identified with the microprobe. Using the petrographic microscope in cross-polarized light, a light-brown material was observed that lined some of the air voids and cracks; however, exact mineralogic identifications were not made. Although many instances of chalcedony and other deleterious quartz phases were found, no clear evidence of ASR-gel deterioration was present in our samples using these methods. However, positive identification of the ASR gel was made on an in-place concrete near one of our sample sites and in several sample cores using a newly developed chemical test for the soluble potassium ions associated with the gel. The chemical used in this test is sodium cobaltinitrite, Na3Co(NO2)6.

Jan 1, 1999

This paper deals chiefly with the preliminary examination, when a decision has to be made as to whether a prospect has a chance of developing into a mine or not. At this stage it is important to have a fairly clear conception of what is expected of the prospect, andjust what type of mine is sought. Much money can be wasted testing a prospect suitable for a prospector or small syndicate, but which never looked like becoming a mine of sufficient size to interest a company. When undertaking an inspection, therefore, it is necessary to have a broad outline, at least, of the policy of the principals for whom the report is intended.At this early stage it is frequently necessary to form an opinion of the prospects of a property on very meagre data. When new to this type of work one's first reaction is often th~t it is impossible to pass an opinion on the data available. It. is absolutely necessary,however, that an opinion of the possibilities and chances of favourable development be given; The report should strive to convey this information, making quite ::lear the risk involved, how complete are the data on which this opinion is based, and the possible magnitude of the prize. A Preliminary report has to state whether a property has sufficient prospects to warrant testing.The following procedure is suggested in order to make best use of the data and minimise hasty conclusions influenced by preconceived ideas-an ever-present danger.Examination.The first stage is the examination. This should aim at collecting all available significant data, but avoid clouding the issue with detail which, at this stage, will not affect the decision. The following points are considered to be the main ones for which to look:-Geological Environment.As good a working knowledge as possible'of the geology of the area should be obtained. Government Geological Survey reports and maps, if available, will be a big help. A detailed knowledge of the regional geology is not necessary a,t this stage, but a broad outline of the geological setting of the prospect under review, and also of any other important mines in the district, is often helpful in the final decision.The Nature of the Ore-Body.Any facts concerning the nature or occurrence of the lode should be noted as, coupled with experience of similar bodies, they affect the ultimate decision.Structural Control.This is probably the most important factor, in the light of present geological knowledge. Its chief importance is due to two facts:-(a) Structure plays one of the prime parts in ore deposition.(b) Geological knowledge, of structure is somewhat in advance of knowledge of other factors influencing ore deposition.

Jan 1, 1950

Same-batch and non-blind as well as blind pulp duplicates are often submitted as quality assurance/quality control (QA/QC) control samples to a routine laboratory along with routine assays (and other control samples such as reference material samples). The current ways of interpreting the results of duplicate assays to derive QA/QC conclusions and decisions, however, has not yet been formalised in a scientific manner. The current, prevailing approach and its limitations are reviewed and a new method is proposed as a substitute tool. This new tool should allow for operational error detection on a batch per batch basis (ie batch rejection) as well as laboratory performance assessment with time on reproducibility.

Jan 1, 2008

By Dean Lindsay, Inna Dymov, Mariam Melashvili, Jim Smolik, Chris Fleming

"This paper presents results from the proposed cyanide detoxification circuit for Seabridge Gold’s KSM project. The proposed flowsheet uses a two-stage CCD (counter-current washing/decantation) circuit to transfer the flotation products CIL(carbon-in-leach) barren solution to a SART process (Sulphidization, Acidification, Recycling of precipitate, and Thickening of precipitate) to recover copper and free cyanide from the copper cyanide complex. The SART barren solution is then treated by an AVR process (Acidification, Volatilization of HCN gas, and Reneutralization) to concentrate the cyanide that was liberated in SART for recycling to leach. The washed CIL barren pulp (the CCD underflow) is treated with the SO2 /Air process to oxidize residual cyanide.The goal of this complex flowsheet is to recover and recycle as much cyanide as possible and produce a final effluent containing less than 0.5 mg/L copper and CNWAD at the lowest cost. The SO2/air process is capable of achieving low residual CNWAD (<1 mg/L) in the final product, but the persistence of aqueous copper above the target level has been detected in the treated solution in some instances. The expected high concentrations of copper and cyanide in the KSM CIL barren ( >200 mg/L each species) and the difficulties this might create for the SO2 /air process was a key factor in the decision to consider including the washing, SART and AVR steps in the project flowsheet.The target concentrations of CNWAD and Cu were readily achieved after aging the SO2 /air treated pulp, as would occur in a tailing or polishing pond. This suggests no additional treatment will be required to sustain low levels of these species in the final plant effluent."

Jan 1, 2015

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal supports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012

By James J. Kabat, James A. McDonald

Impregilo/SA Healy JV recently completed this Project using the first slurry shield TBM’s in the United States. The Project used two TBM’s to mine 18,000 feet in sands, gravels, and silty alluvial materials under the Willamette River and downtown Portland, Oregon. This paper discusses alignment and geological conditions, equipment selection and plant setup, and tunnel excavation means and methods, parameters, and results. Extensive hyperbaric operations were required and will also be discussed.

Jan 1, 2007

By Ron Millions, J. A. Folinsbee, Ishwinder Grewal, Michael Fullam, Don Strickland, Tony Y. Chong

"Since milling began in 1912, the Dome mill, now part of the Porcupine Joint Venture (PJV), has been expanded several times, the most recent increasing the milling rate from 3,500 to 11,500 tonnes per day. Dome uses conventional crushing and grinding followed by gravity concentration to recover free milling gold. A cyanidation/CIP process recovers the remaining gold in the gravity tails.Over the past few years, continuous gravity improvements have increased the gravity recovery from 20% to nearly 50% of the plant feed gold. This paper describes some of the factors that have contributed to this dramatic increase, and suggests how gravity recovery can be further improved. Gravity circuit availability has been improved to >98% with the implementation of a preventative maintenance program. More Knelson concentrators have been added to the circuit, and in 2002, an Acacia Intensive Leach Reactor was installed to replace the shaking table. In 2003, the entire gravity circuit was audited to evaluate and quantify the circuit performance. The metallurgical and mechanical operating conditions of the gravity circuit are now well understood, and areas for further improvement are well defined.INTRODUCTIONThe Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. One of the goals of the JV was to use the milling capacity of the Dome mill to process ore from Placer Dome and Kinross mines in the Timmins Camp. The PJV Dome Mill utilizes gravity concentration, cyanide leaching and carbon in pulp gold circuits to recover gold. Gravity recovery has been used in some form at the Dome Mill for most of its existence, first using conventional jigs, these being replaced in 1993 by two Knelson Concentrators, one for each of the two grinding circuits in the Dome mill. Over the years more concentrators have been added to improve the gravity recovery, most recently in 2002 for a current total of five. Also in 2002, an Acacia Intensive Leach Reactor was added to process the Knelson concentrate, replacing the shaking table."

Jan 1, 2004

By K. L. Cashdollar, C. K. Man, J. R. Gibbins

Oxyfuel combustion is currently one of the principal technological options being considered for capturing carbon dioxide from pulverised coal power plants. In oxyfuel combustion, coal is burnt in a mixture of recycled flue gases and added oxygen instead of in air. In principle this yields a flue gas containing only carbon dioxide, water vapour and small amounts other impurities. Oxyfuel combustion is superficially similar to combustion in air, but there are inevitable differences. This paper describes ignition tests on pulverised coal suspensions using a suite of coals of different rank and from different countries of origin and over a range of oxygen and coal concentrations of interest for oxyfuel combustion. The ignition tests were carried out using the National Institute for Occupational Safety and Health (NIOSH) 20-litre explosion chamber. The purpose was to determine how easily the various coals ignite and burn in mixtures of O2 and CO2 compared to their combustion in air. The residual char volatile and ash contents for the ignition residues were measured using a thermogravimetric analyser (TGA), allowing Q factors (i.e., enhancement in apparent volatile yield due to higher heating rates and/or heterogeneous reactions) to be determined and compared. An ignition index has been derived from the explosion and char data. This index has been used to rank low volatile coals for ignition propensity in air. The results show that to obtain ignition and combustion comparable to that in air, the oxyfuel O2-CO2 gas mixture must contain over 30% O2. Keywords: CO2 capture, combustion, pyrolysis, oxyfuel.

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize productivity, the influence of reclamation parameters must be well understood ? which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass appraisals, and also the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, we use biomass production experimental plots on reclaimed mine sites established by the Powell River Project (PRP) for a comparative study between satellite measurements of Normalized Difference Vegetation Index and inventory estimates of biomass under a variety of conditions. The PRP is a unique public-private partnership in the coalfields of southwestern Virginia dedicated to enhancing beneficial use and environmental protection of mined lands.

Feb 27, 2013

By H. Hejny

"The mine of the future will exploit mineral raw materials at greater depths than today, requiring completely different approaches compared to today’s deep mines, in order to get mineral rights. Only these eco-efficient mines will contribute to improved access to domestic mineral resources, secure the sustainable supply of mineral raw materials for Europe and reduce the import dependency. IntelliMine will contribute to realise these concepts of invisible, zero-impact and safe mines. The mine of tomorrow will run an integrated concept in order to guarantee the desired level of sustainability. All operations necessary for the eco-efficient provision of the minerals including waste management will be carried out underground. This will drastically reduce the volumes being transported, minimising above ground installations and thus the environmental impact. IntelliMine will develop necessary innovative methods, technologies, machines and equipment for the safe, eco-innovative, intelligent and economic exploitation of mineral raw materials in the EU, especially at greater depths."

Jan 1, 2011

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By Donald J. Murphy

Longevity of structural units, as compared to the planned useful life of a facility, always is a design consideration. Typical concerns include slow decay due to environmental factors, and changes in constitutive relationships governing the performance of the material involved. With respect to foundations, the usual items of interest are corrosion of steel and concrete, and time dependent behavior of the soil/structure system. For piles, as with other foundations, deterioration is precluded, mitigated or otherwise accounted for by assessing properly the ambient situation (sulphates, pH, stray currents, resistivity) and providing safeguards, such as resistant construction products, oversizing, coatings, and/or cathodic protection. On the other hand, long term performance of the pile foundations, as affected by time dependent characteristics of the supporting soil or rock, can be predicted and controlled only with a synergetic coupling of analyses and field tests. The history of a project for which this approach was followed forms the basis for this paper.

Jan 1, 1986

By K. Awuah-Offei

Energy efficiency has become significant due to cost and environmental considerations. Comminution and material handling have been identified as the two most energy intensive processes in mining. The objective of this work was to evaluate truck-shovel energy efficiency strategies using discrete event modeling. Energy audits and time and motion studies were conducted at a surface coal mine to acquire data. A discrete event simulation model of truck-shovel operations was built in Arena® and validated with the field data. The model was used to evaluate the effect of using a larger shovel, and optimizing truck-shovel matching on fuel efficiency. The results indicate that using a larger excavator increases the fuel efficiency of the operation while optimizing truck-shovel matching does not. However, using a larger shovel will lead to under-utilization of the shovel. This work shows the potential benefits of using discrete event simulation to model energy efficiency of mining operations.

Jan 1, 2012