Search Documents

By Jin-Chun Kim

Nanosized W based powders (W, WC, WC-Co) were produced by chemical vapor condensation (CVC) process. Two different solid W(CO)6 and Co2(CO)8 metal-organic materials were used as precursors. CVC experiment was conducted in the temperature range of 400-1100. As-CVC WC1-x powder which had non-stoichiometric composition was carburized by using of the CH4-H2 mixed gas in temperature range of 750-850. The CVC W and WC1-x powders showed loosely agglomeration structure, and the Co powder had intricate long stand structure because of intrinsic magnetic properties of Co phase. Carbon content of the CVC powders controlled by gas-phase carburization was well matched with theoretical WC stoichiometry (6.13wt%).

Jan 1, 2006

By Ronald K. Riddle

The processing of lateritic ores in rotary drying and preheating/pre-reduction systems has historically been plagued by problems associated with significant dust generation. These problems include handling issues, kiln capacity limitations, negative impacts on furnace stability, a reduction in nickel recovery and higher operating costs. The dust is formed in the rotary devices during heating and tumbling due to the following three mechanisms: (I) mechanical dccrepitation of the ore as a result of tumbling and attrition, (2) thermal decrepitation during rapid vaporization of internal free and bound water, and the (3) loss of free moisture which functions as a binder. This paper investigates the causes of dust formation, provides methods to reduce dust carryover from the rotary devices, and finally offers methods to recover the dust in the existing pyrometallurgical process. Keywords: Laterite, Drying, Rotary, Dust

Jan 1, 2004

By Peng ZANG, Qihang Liu

Experimental work was conducted to determine the relationships of coal char conversion with temperature and heat absorption. The results show that at an earlier stage of the coke forming process, lump coal would absorb large amounts of heat but the increase of high temperature strength of lump coal was not significant. Contrarily, the lump coal’s high temperature strength was greatly improved at later stage of coke forming process. A number of residual coal was found in most tuyere coke samples illustrating that the lump coals added in the melter gasifier were not completely transformed into coke when they arrived at the tuyere region. The results indicate that the improvement of lump coal’s high temperature performance is limited in the melting gasifier by the low coke forming rate which could become the core factor of fines generation of lump coal in the melting gasifier.

Jan 1, 2016

By Norihiro Murayarna

Hydrothermal synthesis of K type zeolite was carried out by using coal fly ash as a raw material and KOH as an alkali source. The change in various physical properties of the obtained zeolite, such as the kind of zeolite crystal, cation exchange capacity, surface structure of zeolite and particle size distribution were investigated through the overall reaction of zeolitization. The reaction mechanism of K type zeolite from coal fly ash was investigated from these results in this study

Jan 1, 2002

By Michael Sheedy

Sulfuric acid is widely used as an electrolyte for the electrorefming and electrowinning or metals. Impurities in this electrolyte are controlled by continuously bleeding solution from the tank house. In addition to the contaminant these bleed streams contain high levels of sulfuric acid and the metal being recovered. Subsequent treatment of these bleed streams often requires neutralization which generates large volumes of solid waste. Absorption resin technology employing a novel ion exchange technique known as Recoflo® allows the separation of the mineral acid from dissolved metal salts. The recovered acid is suitable for recycle back to the electrolyte circuit. The metal salt and other contaminants leave the process free .of the sulfuric acid. In this process, known commercially as the APU®, ion exchange resin is used to sorb sulfuric acid while excluding the metal salts. The purified acid is then removed by washing the resin with water. The process has been extensively used for the recovery of waste pickling acids in the steel industry and anodizing solutions in the aluminum industry. In the mining and metallurgical industries the process has been successfully evaluated for the separation of excess sulfuric acid from copper electrolytes, the removal of magnesium and manganese contaminants from zinc electrolytes, and nickel and copper from copper electrolytes. A full scale installation on a copper refinery bleed stream at Palconbridge's Kidd Creek plant in Timmins, Ontario has now been operating successfully for more than 1 year while pilot field trials have been successfully completed on other applications.

Jan 1, 1997

By R. G. Hilton

This paper deals with application of Super Detox? stabilization technology to the treatment of electric arc furnace dust (US-EPA listed hazardous waste KO61 ). The process has been used on approximately 170,000 tons of electric arc furnace dust. In addition to the nearly four years of commercial experience at Sterling, Illinois, the process is now being permitted for application at two other locations. The process was originally developed by the Bethlehem Steel Corporation and then further improved by Conversion Systems, Inc. (Bethlehem Steel's Licensee). The treatment process offers many unique bases for its selection, including: A) Low cost compared to the treatment alternatives; B) Lowest available TCLP leachate levels for any process treating K061. Many other processes leave some residue that represents a disposal requirement, although often not addressed; C) Produces minimized final waste disposed, including the fact that the total volume of dust generated and less than the volume occupied by the residue slag from HTMR; and, D) Opportunities for the beneficial utilization of part or all of the waste stream through the development of chemical and physical characteristics. Each of these aspects will be specifically discussed in the paper, including that status of the operations now under permit.

Jan 1, 1994

By Yutaka Yasuda

The particle dispersion phenomena in a turbulent gas jet of the flash smelting process has been investigated. The particle number density in a non- reacting jet was measured experimentally by taking photographs of the particles in flight and counting them using the image analysis. Numerical computations were also performed using a mathematical model for a turbulent particle laden gas jet The experimental particle number density data were then compared with the predicted results of the model. Good agreement was obtained between the experimental and predicted data. The effects of the parameters such as the injector design, particle loading and air flow rate are discussed. Optimization of the concentrate burner design can be achieved with the help of experimental and theoretical simulation as performed in this work.

Jan 1, 1994

By W. Kasprzak

Press-fit systems are widely used to seal oil lines in the automotive engine components. In the case studied a ball plug made from the 7075 A1 alloy was inserted into a 319 Al alloy cast component. The oil lines were subjected to the required component service pressure. This paper addresses the analysis of the ball plug/casting hole press-fit performance. The tools used to investigate the plug system included: the SEMIEDS technique for the assessment of the plug and the casting hole wall surface integrity; image analysis methods for the characterization of the ball plug/casting hole interface; matrix microhardness measurements of the plug and casting components; laboratory ball plug insertion, speed and force correlation; as well as the ball shearing mechanism analysis. Laboratory tests indicated that optimization of the aluminum matrix hardness in the 319 A1 alloy cast components resulted in considerable improvement of the press-fit system sealing properties.

Jan 1, 2002

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

By Arthur S. Klein, Hugh R. Lowry

"The Levitation Casting Process is a new continuous casting method that uses an electromagnetic levitation field, instead of a mold, to support and contain a column of solidifying metal. By counteracting gravitational forces and hydrostatic pressure on the metal column, this process eliminates friction and adhesion at the interface between the solidifying metal and the cooled walls of the casting chamber. The process inherently provides high casting speeds, excellent dimensional control and smooth, continuous emergence of solidified product from the top of the casting chamber.Of major importance is that the electromagnetic field produces an intense stirring of the liquid metal both before and during solidification. As a result of this stirring, the cast product has a homogeneous, equiaxed, fine grain structure generally suitable for immediate drawing or other forming operations without the need for hot rolling or other expensive additional processing.This paper reviews the fundamentals of the Levitation Casting Process, results obtained in casting various pure metals and alloys, and the production sized system at Lowell, MA, that uses this process. IntroductionThe Levitation Casting process was specifically developed to meet several requirements including:• Economic at low casting rates• Usable with pure metals and alloys• High, uniform product quality suitable for fine wire drawing or cold rolling into flat strip and tape• Easy cast product shape and size changes• Process inherently stable and easily automatedIn meeting these criteria it was also desired to retain the advantages of General Electric's well known Dip Forming continuous casting process; namely the inherent ""fail-safe"" properties of upward casting, solidifying metal by means other than pressure contact with a cooled mold, and use of a sealed furnace, casting chamber and cooling tower, filled with a protective atmosphere, to prevent oxidation of the molten metal or cast product."

Jan 1, 1988

By Jenq-Gong Duh, Jyh-Wei Lee

"Hard chromizing process is a method for developing a surface modified coating providing wear, corrosion resistance and high temperature surface protection. Two carbon steels with 0.45 wt% and 0.95 wt% carbon contents, respectively, were chromized with pack cementation process at 950'C for 4 and 9 hours, respectively. The phase transformation and microstructure phenomena of chromized coating layer and matrix of two steels were studied with X-ray diffractometer and electron probe microanalyzer. (Cr,Fe)23C6 and (Cr,Fe)7C3 carbides and (Cr,Fe)2N1-x nitride phases were observed on the chromized surfaces. The thickness of chromized layers obeyed the parabolic rate law. The mechanism and diffusional kinetics of the chromizing process were proposed. The diffusivity of chromium in the (Cr,Fe)7C3 carbide phase was calculated using the moving boundary method.IntroductionChromizing process is one of the surface treatment technologies that can produce a chromium contained surface layer with sufficient corrosion and wear resistance on the steel matrix [1-7]. The relatively low cost and no ""line-of-sight"" restrictions are main advantages of chromizing. Adequate bonding strength of these coatings to the substrate was reported [7]. Chromizing process can be classified into soft chromizing and hard chromizing [2]. Soft chromizing is applied to steels containing less than 0.1wt% carbon through which chromium will be diffused. High temperature oxidation resistance improvement is the main purpose of soft chromizing process. On the contrary, the hard chromizing can be applied to steel containing more than 0.3wt% carbon, and very hard chromium nitride and carbide layers will be formed on the surface, which are very resistant to wear, corrosion and temperature [5-7]. In the previous studies on the Fe-Mn-Al-Cr alloy [5,7] and carbon steels [6], the thickness (X) of chromizing layers was analyzed and found the parabolic rate Jaw prevailed:"

Jan 1, 2004

By Per Anders Eidem, Merete Tangstad, Jens Davidsen

"During excavations of submerged arc furnaces producing silicomanganese, silicon carbide (SiC) has been found. Contributing to the size of the inactive area of the furnace, the active area of the furnace where reactions occur will decrease, thus reducing the potential for pre-reduction in the furnace.This work studied the formation of SiC from the liquid-solid reaction between slag, metal, and metallurgical coke. Slags and metals with different levels of silica (S1O2) and silicon (Si) have been studied. The slag and metal has been heated together with coke, and the samples investigated by microprobe. The results show that SiC was formed on the coke particle through reactions with both slag and metal. For the metal, the carbon most likely diffused through the SiC to react with Si in the alloy. SiC formation with slag is likely to go through the reduction of Si02 to Si.IntroductionToday, Silicomanganese (SiMn) is produced in submerged arc furnaces (SAF) by reduction of S1O2 and manganese oxides, mainly with metallurgical cokes. Typically, the tapped metal has a silicon content of 17 - 20 wt.%. To achieve higher levels of Si, the metal can be refined by adding off-grade silicon metal, yielding low carbon SiMn. [1]. What is believed to be SiC that has been found during dig-outs of SiMn furnaces producing high silicon alloy. It is possible that excess amounts of SiC in the furnace cause operational problems, since SiC will occupy furnace volume. As SiC accumulates, the active volume of the furnace will decrease, increasing the flow of material and gas in the active areas of the furnace. Formation of SiC is inevitable, so it is desired to keep the formation as low as possible. To be able to control the formation of SiC, one has to understand the basic mechanisms."

Jan 1, 2012

By Djalma Souza, Rubén Sánchez, Regina Maria Pinheiro, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

"This work has for objectives to characterize a waste generated in the form of sludge during the treatment of the effluent of a paper making industry and to evaluate the effect of its incorporation up to 10 wt.% on the properties of a clayey body used for brick production. For the characterization of the waste the following techniques were used: X-ray diffraction, X-ray fluorescence, differential thermal analysis and termogravimetric analysis with mass spectrometry. Specimens were prepared by uniaxial pressing at 20 MPa before firing at 750 °C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The results showed that, in agreement with the characteristics of the waste, its recycling into red ceramic can contribute to decrease the consumption of fuel during the firing stage. However, the waste changes the physical and mechanical properties, generating a deleterious effect on the water absorption and flexural rupture strength of the ceramic.IntroductionAccording to the Brazilian Association of Pulp and Paper, in the last 10 years, the global production of paper grew 35%. Brazil produced 8,2 million tons of paper in 2004 and held the position of the seventh largest world manufacturer of pulp, with about 9,4 million tons per year [1]. The pulp and paper industry generates effluents that present problems related to their disposal, even after the treatment. Among the solid wastes generated by this industry, the main waste is the primary sludge from the effluent treatment plant (ETP).After the initial treatment the decanted solids go through a dewatering stage, generating the solid form denominated primary sludge. This sludge resembles a paper paste of dark gray color when humid, and clear gray color when dry. This primary waste is composed basically of kaolin, pulp, traces of chemical substances and water. This waste generated in the pulp and paper industry depends on the characteristics of the process and of the employed techniques. It can vary significantly from one industrial unit to another, even in the case that the final products are similar. Its composition is approximately 60% of kaolin and 40% of pulp, and these percentages can vary in some moments as a function of the process [2,3]."

Jan 1, 2008

By Bora Derin, Adnan Aydin, Onuralp Yucel, Hakan Morcali

"The steelmaking industry which uses electric arc furnaces (EAF) generates approximately 250.000 tons of EAF flue dusts annually in Turkey. These flue dusts contain valuable metals such as zinc, iron and lead. For example, if these flue dusts can be treated efficiently, disposal problems certainly decreases and annually almost 40.000-75.000 tons of zinc can be recovered. In this study, powder and pellet forms of EAF flue dusts taken from a steel mill were carbothermally treated in a temperature controlled pilot scale rotary furnace via carbothermal reduction in order to investigate the reduction behavior of Zn and Pb. Temperature (900-1000 and 1100 °C) and time (0-90 minutes) were selected as reaction parameters. The chemical analysis was performed for the sample residues.IntroductionTurkey’s steel production reached to 23.3 million tons in 2006. There are three integrated steel plants of which capacities vary from 0.7 to 3 million tons per year and seventeen EAF steel plants of which capacities vary from 0.06 to 2 million tons per year [1]. When it is considered that more than 74 % of the Turkish steel production is produced by EAF method and approximately 10 - 15 kg of dust is formed per ton of steel during this process, the amount of annual generated EAF dust may be estimated at approximately 0.25 million tons. EAF dust which contains valuable metals such as zinc, lead, iron, cadmium, and chromium, is considered as hazardous waste product in steelmaking industry. If these flue dusts can be treated efficiently, not only the disposal problems certainly decrease, but also annually almost 40.000-75.000 tons of zinc can be recovered. Many studies which exist on recovering of the valuable metals from EAF dust, propose and practice many hydro-metallurgical and pyro-metallurgical treatments [2- 7]. In this study a laboratory scale work were performed to investigate reduction behavior of zinc and lead in EAF dust by carbothermal process in a rotary furnace."

Jan 1, 2008

By F. Patisson

One of the major issues with multiparticle reactors is to handle their multiscale aspect. For modeling, it usually comes to coupling a reactor model (describing the phenomena at the macroscopic scale) with a so-called grain model (simulating the behavior of a single grain or a particle). An interesting approach proposed by H.Y. Sohn (1978) is to use the law of additive reaction times in order to calculate, approximately but analytically, the reaction rate of a particle in the reactor model. Its great advantage, compared to a numerical grain model, is to drastically reduce the computation time, particularly in the case of complex reactor models. This is the approach we retained for modeling the moving bed furnace, a counter-current gas-solid reactor used in the nuclear fuel-making route for producing uranium tetrafluoride from uranium trioxide. The numerical model we developed is 2-dimensional, steady-state and based on the finite volume method. It describes solid and gas flow, convective, conductive and radiative heat transfers, and six chemical reactions involved in the process. The law of additive reaction times is used to calculate analytically the rate of the three principal gas-solid reactions at every discrete point in the reactor. We have demonstrated the validity of this approach by comparing its results with those calculated from a numerical grain model. Also detailed in the paper are the main results of the moving bed furnace model itself and the possibilities of optimizing the process revealed by the calculations.

Jan 1, 2006

By R. Dekkers

Non-metallic inclusions in liquid steel are mainly formed during killing. As far as these particles are not captured by the slag, they are found in the cast steel where they can deteriorate the mechanical properties. Inclusions may also disrupt the continuous casting process, affecting thus directly the quality of the steel and the production capacity. Steel pin samples from the Sidmar plant (Belgium) were taken in different steps of several ladle treatments and in the tundish. Also slab samples were studied. All samples concern the same type of low alloyed aluminium killed steel. The non-metallic inclusions were isolated from the steel matrix and investigated with scanning electron microscopy and energy dispersive spectrometry. The evolution of the non-metallic inclusions is described by their number, size, shape and elemental composition. The main non-metallic inclusions present are aluminium oxides and spinel type compounds.

Jan 1, 1999

By Wayne Bell, Xiaodi Huang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng

"The equations for determining microwave field attenuation length and half-power depth in magnetic materials were derived from Maxwell’s equations. The microwave field attenuation length and the half-power depth for a magnetite concentrate were calculated and the temperature dependence of them was determined. It is demonstrated the microwave field attenuation length and the half-power depth highly depend on temperature and decrease with increasing temperature up to 900 °C. The variations of field attenuation length and the half-power depth with temperature indicate the microwave power attenuates much faster than the field strength in materials. The evaluations of field attenuation length and microwave half-power depth can be used to characterize the microwave dissipation behaviors in the sample and optimize the dimensions of the material in microwave heating.IntroductionMicrowave has been applied in materials processing for its distinguished advantages including rapid heat transfer, volumetric and selective heating [1,2]. However, most research work involving microwave heating are confined to non-magnetic materials (e.g. ceramics), with limited attention paid to the heating of mixed property materials (e.g. magnetite and other ferrites) under microwave irradiation [3-5]. Since many magnetic materials exhibit good and even better microwave absorption capability than non-magnetic counterparts, it is quite necessary and deserved to take advantage of this property and then improve the heating efficiency. To achieve this aim, further understanding on the microwave heating mechanism, especially the microwave propagation/dissipation behaviors in magnetic materials is required.The dissipation behavior of microwave in materials has been identified as one of the key factors that affect the efficiency of heating under microwave irradiation and this behavior can be characterized by several parameters. Apart from traditional penetration depth (TEM power penetration depth, Dp = 1/(2*a), where a is the TEM field attenuation factor), two other parameters, field attenuation length (Df) and half-power depth (Dh), are also applied to indicate the microwave dissipation in materials [6].The accurate determination of such parameters can help in optimizing the dimensions of the load in a microwave furnace, producing more uniform heating under microwave irradiation and avoiding thermal runaway."

Jan 1, 2011

By L. L. Ludwig, S. E. James, B. L. Motycka

Significant modifications to the electrolytic zinc plant operated by Big River Zinc Corporation were made at the end of the 1990's resulting in increased capacity and improved efficiencies. A new cell room, with the innovative use of acid-resistant concrete cells and a modern ventilation system, was installed to raise the capacity from 80,000 tonne/y to 106,000 tonne/y of finished zinc. Improvements to the leaching section include the conversion from a single to a two-step process, with associated equipment changes, to improve the quality of the residues produced. Another key change is the construction of a facility to allow the use of zinc oxides from secondary sources as a feed to the plant. This paper describes these improvements and the current operations.

Jan 1, 2000

By M. H. Lin, S. Kou

"Czochralski pulling has been a very widely used process for growing single crystals for electronic and optical applications. Dopant segregation can significantly degrade the quality and yield of single crystals. We have used the floating-crucible technique for segregation control in Czochralski pulling, our floating crucibles being unique in that the melt passageway is very long. As such, dopant back diffusion is suppressed, even when the cross-section of the melt passageway has to be relatively large to help the melt go through or when the pulling rate is very low. Single crystals of model materials K-doped NaN03 and Pb-doped Sn have been grown with very uniform dopant concentrations. IntroductionSingle crystals of electronic and optical materials are often doped with a small amount of impurities to develop required physical properties, e.g., P and B in Si for n-type and p-type semiconductors, respectively, and Nd in YAG lasers. Dopant segregation can result in nonuniform physical properties, thus degrading the quality and yield of the resultant crystals.Figure 1 is an illustration of the conventional Czochralski process for crystal growth. Several techniques have been developed to control dopant segregation in Czochralski pulling, including the push-pull technique (1,2), the drop-pull technique (3-7) and the floating-crucible technique (8-13). The first two techniques require precise sensing devices and feedback control systems to keep the feeding rate equal to the pulling rate. The last technique is simple since the feeding rate is automatically equal to the pulling rate."

Jan 1, 1994

By Jiechao Liu, Lijian Luo, Yubao Ma, Bo Zhang, Yanfeng Yang, Xin Hong, Luming Liu, Jienan Liu

Reduction kinetics of stainless steel slag in iron bath smelting reduction was studied at the temperature of 1500℃ ~ 1650℃. It was concluded that the reduction process consisted of two parts. That is to say smelting reduction was controlled by stainless steel slag melting initially and by interface reaction later. In order to increase smelting reaction rate, the melting point of slag should be decreased at the first stage and adjust the liquidity of slag at later stage. Smelting reaction rate will be accelerated by means of optimize the slag content. The optimal reduction result that all most all of the chromium in slag been recovered was obtained in temperature was 1500℃, basicity of slag was 1.0~1.2, the value of Al2O3+MgO was 25%.

Jan 1, 2015