Search Documents

By Norihiko Fukatsu, Takashi Iwamoto, Noriaki Kurita, Koji Katahira, Kunihiro Koide, Teruo Ohashi

"The galvanic cell-type hydrogen sensor employing CaZro.9Ino.t03-a. as the solid electrolyte was designed for the measurement of hydrogen activities in molten copper under industrial .conditions. The sensor probe consists of the cap-shaped solid electrolyte with porous platinum electrode on the inside and alumina refractory tube. The gas mixture of the composition 4%H2-0.5%02-Ar was made to flow on the inside electrode. The hydrogen sensor probe was inserted directly into molten copper and the melt was used as the outer electrode. The effect of oxygen activity gradient to EMF was eliminated theoretically by measuring the oxygen activity in the melt simultaneously with an oxygen sensor. The high stability of output and excellent response to the change of hydrogen activity were obtained over the wide range of industrial copper melting conditions.IntroductionIn the metal casting process, hydrogen easily dissolves in molten metals from water vapor in the surrounding atmosphere. Owing to the large difference in hydrogen solubility between liquid and solid metal, dissolved hydrogen becomes a cause of the defects of blowholes in castings or ingots. It is necessary to control the hydrogen content in the molten metals [l]. Using proton-conducting ceramics as a solid electrolyte, high temperature-type hydrogen sensor can be constructed [2]. SrCe03- and BaCe03-based perovskite-type oxides exhibit appreciable proton conduction under hydrogen containing atmosphere at high temperature [3-5]. A hydrogen sensor for molten aluminum using CaZro.91no.103-a. has been developed and widely used in the ·process control in the aluminum melting industry [6,7]. The same type of hydrogen sensor has also been expected in the copper melting industry. .. However, CaZro.91no.103-a shows ·not only proton but also oxide ion conduction in the high temperature and at low oxygen activies like the copper melting· conditions. Then we studied the oxide ion conduction in CaZro.91no.103-a. iit · detail [8]. From the consideration on the EMF of the galvanic cell employing this material as electrolyte, it was shown that the unknown hydrogen activity may be precisely determined from cell potential which is corrected for the effect of oxygen potential gradient And the hydrogen sensor based in this principle was constructed and tested in laboratory-scale [9,10]. We repeated the similar tests in factory-scale and developed the sensor system for practical uses [11, 12]. In this report, the structure and system of the hydrogen sensor for molten copper will be introduced first. The reliability of the sensor will then be demonstrated from the results of experiments for sensor probes carried out in TYK's laboratory."

Jan 1, 2000

By N. B. Gray, I. F. Taylor

"Gas injection to promote chemical reactions or mixing is a feature of many metallurgical processes. Often the aim of gas injection is to bring about a chemical reaction between the gas and liquid but most of the past physical and mathematical modelling work has ignored the influence of such reactions. In the work reported here, cold model studies have been conducted in which gas reacts with the liquid into which it was injected. The rate of liquid mixing has been measured as an indication of the mechanical energy transfer. It has been found that gas generated chemically within the liquid is significantly less effective at promoting mixing than the equivalent volume of inert gas. The relative ineffectiveness of chemically produced gas is thought to be due to smaller bubble sizes in comparison to the inert gas case. Small bubbles characteristic of chemically generated gas move with low slip velocities relative to the liquid and lead to different turbulence generation mechanisms.IntroductionIn processes such as steelmaking, copper conversion, bath smelting and ladle steel finishing gas is injected into liquid metal where it reacts chemically or simply serves as a source of agitation. An understanding of fluid flow phenomena in such situations is an essential pre-requisite to the calculation of process intensity and the optimisation of vessel productivity. Traditional physical cold modelling approaches to prediction of liquid flow in such situations are now often augmented by the techniques of computational fluid dynamics. Even with the availability of numerical modelling techniques cold physical models continue to have an important role for validation because it is generally difficult to obtain quantitative data from high temperature processes.Almost all previous cold modelling work has been based on the injection of an inert gas into water or some other non-reactive liquid. Such models do not include the significant increase in gas volume inherent in some processes. For example the oxidation of carbon in steelmaking leads to a twofold increase in molar gas flux through the reaction:"

Jan 1, 1996

By Hadi Fanisalek

"Most industries attempted to conduct their energy consumptions in an optimized way for a few decades. This is because policymakers and top managements in industries have felt the critical situation of a possible energy shortage that could happen for them in the near future, even in countries with significant fossil fuel resources. Decisions related to energy consumption in any industry will have a long-term effect on different parts of the industry structure. In this way, energy decisions should be categorized as part of any industry's main strategic and long-term decisions, which should be made by top strategists. On the other hand, strategic management has many powerful tools to help the policymakers in industries to establish a long-term strategy for energy consumption and reducing or preferably eliminating the energy loss. This will be more important for industries in the Middle East, where they have just started to make an applicable strategy for their energy consumption and to design a long-term procedure for their energy management. Based on strategic management and by comparison we designed and offered a new model for establishing the main structure of energy management strategy in primary aluminum industry, which is a high consuming energy industry. This strategy, which we will call ESM (Energy Strategic Model) and has been applied for a typical primary aluminum industry in this paper, is similar to the practical models in the field of strategic management, which were developed for designing the overall company strategy.IntroductionThe elementary goal for introducing strategic management in any organization was to establish a successful plan helping the company to survive and to gain competitive advantage over its competitors in a rough business environment. Strategic management is an ongoing process that evaluates and controls the business and industries in which the company is involved; assesses its competitors and sets goals and strategies to meet all existing and potential competitors; and then reassesses each strategy annually to determine how it has been implemented and whether it has succeeded or needs replacement by a new strategy to meet changed circumstances, new technology, new competitors, and a new economic environment[!]."

Jan 1, 2013

By Jan Smit

Sulphidic copper concentrates are generally processed by pyrometallurgical means; while oxidative pressure leach processing of such materials has been shown to be technically feasible, there has traditionally been little incentive to choose this route in favour of a smelting option. However, for concentrates with elevated arsenic levels, oxidative pressure leaching offers distinct advantages, as smelter air emission standards and restrictions on concentrate importation have tightened. The current state of pressure leach technology allows for high copper extractions from arsenical copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. In its studies on pressure leaching of copper concentrates, Sherritt has shown that arsenical feed materials can be converted into environmentally stable residues, with excellent copper extractions. The results of recent batch and pilot plant test work are discussed, including the deportments of copper, arsenic and precious metals.

By Gjergj Dodbiba, Toyohisa Fujita, Takahiro Kikuchi, I-Chen Wu

"In order to separate molybdenum (Mo) from the high-level radioactive liquid waste (HLLW), Pb-Fe based adsorbents were synthesized. The adsorbents were precipitated by adding sodium hydroxide in mixture of 1 mol/L lead nitrate and 1 mol/L ferric nitrate aqueous solutions. Each precipitate was then filtered, dried and ground to obtain a fine powder, which has been used as an adsorbent. Two main parameters were considered when synthesizing the adsorbents, i.e. the pH value at precipitation of adsorbent precursor and the calcination temperature of Pb-Fe based adsorbent. Moreover, the structures of the synthesized adsorbents were investigated by means of an X-ray diffractometer.The experimental results indicated that the calcination temperature of the Pb-Fe based adsorbent has a great influence on adsorption capacity of the adsorbent for Mo. It was found that when the Pb-Fe based adsorbent was calcinated at 500 oC, the sorbed concentration of Mo was the highest.1. IntroductionThe high-level radioactive liquid waste (HLLW), arising from the reprocessing of nuclear fuel are generally immobilized in an alkali borosilicate glass matrix. Broadly speaking, alkali borosilicate glasses are the matrix of choice for the immobilization of the HLLW, since they permit vitrification of waste stream of variable composition, [1]. Within this frame, the incorporation of molybdenum (Mo) is of particular interest in the vitrification of HLLW. Molybdenum is know to have a low solubility in borosilicate glass compositions and its presence in excess results in the phase separation of a complex yellow molten salt during vitrification, [1]. The formation of so-called “yellow phase” material during the vitrification process is undesirable since it leads to the accelerated corrosion of the inconel crucible liners. Furthermore, the “yellow phase”, which is reported to contain also other fission products, is soluble in aqueous solution providing a potential route for the leaching of radionuclides from the vitrified waste, should it come into contact with water, [1]."

Jan 1, 2008

By Lanre Oshinowo

Computational Fluid Dynamics (CFD) is used in conjunction with process modelling at HATCH to achieve a superior level of confidence in the process design of hydrometallurgical process plants. The use of these tools to evaluate designs through virtual prototyping reduces the risks associated with making design decisions. This paper highlights the development of a co-simulation strategy at Hatch for the seamless integration of process modeling software addressing different scales (process time and space): flowsheet level models and .equipment level models. With co-simulation, the process design engineers can improve design accuracy, troubleshoot and optimize performance and influence decisions impacting equipment operation by representing specific unit operations in the flowsheet model software with detailed CFD models. Specifically, this paper will focus on the co-simulation of a Ni/Co high-pressure acid leach (HPAL) process including heaters/heat exchangers and flash system, autoclave and quench/scrubber system. The knowledge developed can be transferable to other processes.

Jan 1, 2004

By J. M. Brupbacher, D. C. Nagle

"The XD TM * approach to producing metal matrix composites employs an in-situ precipitation technique for the formation of the reinforcement directly in the matrix of interest. Key features include: thermodynamically stable reinforcement; clean particle/matrix interfaces, single-crystal reinforcement; size, chemistry, and shape control; uniform distribution; compatibility with conventional ingot techniques; and grain refinement.Using XD~ technology it is possible to simultaneously introduce a number of different reinforcements in a given matrix, thus allowing for designing the microstructure to meet a specific material need. Thus, XD1l'1 technology is a very useful technique for achieving ""designer"" or ""engineered"" microstructures. XD TM technology has been applied to a number of systems including AI, NiAI, TiAI and Cu. Materials property and processing benefits will be discussed."

Jan 1, 1988

By Johannes Boonstra

High rate bacterial catalyzed processes can serve to improve hydrometallurgical operations. These solutions are not only economical but also environmental sustainable. With references around the globe, the value of this new approach is recognized by industry worldwide. For instance, metals can safely and economically be separated from process and waste streams using biotechnologically produced sulfide, recovering a valuable metal sulfide product instead of a waste gypsum stream for disposal. Both the natural biological sulfur and nitrogen cycles offer bioconversions that are applied on industrial scale. The shared advantage of these processes is that waste compounds are converted in either a reusable raw material or in a harmless product. This way, natural product cycles can be closed. Applications based upon bioconversions are for example: Sulfur based: Bioleaching, reduction of oxidized sulfur compounds to elemental sulfur, metal recovery with biogenic produced H2S, SO2removal from gas streams, etc. Nitrogen based: Ammonia removal using the anammox-process, biological removal of NOxfrom gas streams, nitrate removal from water streams, etc. Metals: Bacterial processes for the reduction of metals such as uranium, selenium and manganese have proven to offer great potential for clean-up of groundwater streams. This paper contains a description of the above applications. Further, a short introduction on engineered high rate bioreactor systems and a description of industrial biotechnological applications will be provided.

Jan 1, 2003

By Yong .. Jun Wu

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4Ti3O12 (BIT) which has a positive temperature coefficient of dielectric constant (,E) can be used to modify the negative tE of typical microwave dielectric ceramic BaNd2Ti4O12(BNT), However, BaNd2Ti4O12/Bi4TiO12/Bi4Ti3O12/BaNd2Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C) was much higher than that of Bi4Ti3O12 ceramic (around 1100°C). In this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second step, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti4O12 ceramic pellets and spark plasma sintered at 900°C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe microanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/BIT/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.85, a low dielectric loss of 01068 and a small temperature coefficient of dielectric constant of 35 ppm/°C at MHz.

Jan 1, 2003

By Linda C. White

The use of red mud, a waste product of the ?Bayer? process for bauxite refining, was investigated for its arsenic removal effectiveness from aqueous solutions under various conditions. Red mud efficiently removed As(III) between a pH range of 7.6 and 9; and As(V) in the pH range between 5.5 and 6. Pre-washing of the red mud with salt water considerably improved its arsenic adsorption capabilities. With appropriate red mud dosage, the residual arsenic in solution was decreased below the regulated acceptable arsenic limit (0.1 mg/L) from aqueous industrial wastes. The arsenic adsorption followed first-order rate kinetics and fitted the Langmuir isotherm model. Results suggest that red mud is potentially a useful adsorbent for removal of arsenic from contaminated water or industrial waste solutions.

Jan 1, 2003

By F. Sanchez, A. Mejias, C. Frias, G. Diaz

"Crude zinc oxides are the major source of secondary zinc and are produced from fuming processes like Waelz kilns. The impurities of crude zinc oxides make difficult their processing in primary zinc refineries due to mainly high chloride tenor. Washing with sodium carbonate is a costly operation and chloride removal efficiency is not good enough, so further purification steps are required. The crude zinc oxides are easily treated using ZINCEX™ technology based on leaching, solvent extraction, and electrowinning. The ZINCEX™ process is commercially available and is designed to be a perfect barrier for metallic impurities and halogens, allowing selective zinc extraction in mixed chloride and sulfate leaching solutions. Other valuable components as lead and silver can be efficiently recovered from the leaching residue using PLINT technology in chloride media. Silver is recovered as silver cement and lead is precipitated as pure lead oxide or carbonate, which can be smelted at low temperature.IntroductionZinc is a fully recyclable metal and at present approximately 70% of the zinc produced worldwide comes from primary zinc while 30% originates from secondary materials. Nowadays, the zinc recycling rate is continuously increasing mainly through galvanized steel scrap processing, and crude zinc oxides are the major source of secondary zinc [1]. Secondary zinc oxides are obtained from fuming processes like W aelz Kiln, Rotary Hearth Furnace or Primus Furnace. Waelz is the dominant technology accounting for 80% of total crude zinc oxides production worldwide. In the Waelz process, steel dust is mixed with solid fuel reductant (coke breeze) and pelletized. It is then fed to the kiln and heated to a reaction temperature of l ,200°C. In such conditions, zinc, lead, and other non-ferrous metals are vaporized into the flue gas together with chlorides and alkaline metals. Mixed oxides are drawn from the kiln with the process gases and separated to produce typical crude zinc oxides [2]."

Jan 1, 2011

By Adam J. Gesing

Eddy current separators are increasingly used by the auto shredder operators to produce higher grade of nonferrous metal concentrate for recycling. While this increases the unit price of the concentrate, metal losses through inefficient metal recovery quickly offset the price differential. We show how to optimize the eddy current separation system at the shredder to maximize mate- rial throughput, nonferrous metal recovery and grade of the nonferrous metal concentrate.

Jan 1, 1998

By Mitchell L. Spencer, Viswanathan Panchanathan

"Bonded magnets are important category in permanent magnets. They are made by one of the following processes: compression bonding, injection molding, extrusion, calendering. An overview of the various bonded magnet processes and properties of products made with different magnet materials along with their applications are discussed. The main emphasis will be on the use of bonded NdFeB and ferrite magnets.IntroductionBonded magnets are a major growth area in permanent magnets. Bonded magnets are made by any one of the following processes: Compression bonding; Injection Molding; Extrusion and Calendering [1,2]. Compression and injection molded magnets are rigid magnets. Materials used in calendering process produce flexible magnets. Only the extrusion process makes both rigid and flexible magnets. The binders used for the bonded magnets vary depending on the processes. Thermoset, thermo-plastic and elastomeric binders are respectively used in compression, injection and the calendering process. Extrusion molding uses elastomers or thermo-plastic materials. The most co=on magnetic materials, Ferrite, SmCo, Alnico and NdFeB can be used in any of the above processes either alone or in combination as hybrid magnets. Another material that has been developed for co=ercial application is SmFeN. Making the material has been challenging and it is being used in niche market applications in limited quantitiesIn the extrusion process, a highly loaded compound is used to produce strip or sheet and is continuously extruded through a die. In calendering the granulated compound is rolled to produce a continuous wide sheet. In the compression bonding process a uniaxial pressing force is used. These magnets have higher loading compared to injection molded magnets. In injection molding the material is forced into a mold cavity and has lower loading compared to compression molded magnets [2,3]. Most of the flexible magnets are made using extrusion and calendering processes and the most co=on magnet material is inexpensive ferrite. Flexible magnets have been made using rare earth materials, but on a very limited basis.The major advantages of magnets processed by extrusion and calendering are as follows: inexpensive tooling, automation; practically any 2D geometry; fast production rates; no chipping or breaking; a wide range of properties; on-line magnetization; easy to convert (e.g. cut, punch or shape).Compression bonded magnets are inexpensive to manufacture. They have higher magnetic properties compared to injection molded magnets; however lower than their sintered counterparts. The magnet shape is restricted to simple geometries and they require careful handling. Their isotropic nature allows complex magnetizing patterns."

Jan 1, 2013

By L. J. Friedman

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric ?acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design _to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators, The current? design offers improved' impurity scrubbing along with increased reliability. in addition, a number of alternate gas cleaning systems have been offered Chemetica LAB System; Monsanto DuPont D:Jna-Wave Syatem1 Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems. _

Jan 1, 1992

By James R. Craig

The slags generated during gasification of petroleum coke are heterogeneous and con-sist of many different phases. These phases are important because their physical properties affect the operability of gasifiers and because they concentrate many elements that are present in the petroleum coke feed in only minor to trace quantities. An understanding of the chemistry and physical nature of these slag phases is necessary to predict behavior in the gasifier and in considering the ultimate use or disposal of the materials. Slags typically consist of silicate glasses, calcium-silicates, free iron-nickel metallic phases, iron sulfides, and aluminum oxide spinels enriched in iron, chromium, and vanadium. The partitioning of elements among these phases has been analyzed and will be discussed.

Jan 1, 1989

By Deepu Philip, Pratik Agarwal, Ajay Kumar Shukla, Ishani Shukla, G Rajesh

Steel plants generally employ static BOF end point control models to arrive at a given temperature and chemistry at the end of blow. These end point models have now been supplemented with chaos control models to steer the blowing process in the right direction while the blow is in progress. Merely arriving at the correct end point temperature is however not adequate because in the subsequent stages as well the temperature variations can be large and unpredictable. The present paper deals with an integrated model to take into account the effect of all parameters affecting temperature and composition from tapping to the start of casting to minimize the use of LF or aluminum heating, and also minimize grade mixing. The application of lean operations strategy is explained in which the previous “Push System’ is changed to a “Pull System”, minimizing the use of ladle furnace or aluminum heating during steelmaking.

Jan 1, 2014

By John J. Mahoney, George P. Demopoulos, Matthew T. Bohan

In recent times processing of arsenic-laden complex ores and heightened awareness of the detrimental health effects of arsenic has put an increasing burden on metallurgical operations to remove arsenic from processes for disposal in an environmentally stable form. At present, arsenic is removed and prepared for storage by precipitation of insoluble secondary arsenic-bearing minerals. It has been suggested that Ca(II)-Fe(III)-As(V) phases resembling the natural mineral yukonite, under certain conditions, may have a role in controlling arsenic pore water concentrations in arsenical waste storage facilities. In this study, a previous synthesis method of yukonite (Ca3Fe5(AsO4)4(OH)9⋅4H2O) is revisited and new solubility/stability data is presented based on a modified method.

Jan 1, 2014

By Cindy L. Williams

"The Blue Star subdistrict in the Carlin Trend, Nevada, includes multiple mines with 33.9 t Au in reserve and past production totaling 89 .1 t Au. The deposits are characterized by zoned alteration mineralogy and gold grades. From orebody centers outward the zones include: 1) a silicified core with erratic gold grade; 2) adjacent mill-grade (> 1.37 Au git) intense quartz-sericite-pyrite alteration; 3) enveloping leach-grade (0.21 Au g/t to 1.37 Au git) weaker sericite-kaolinite-quartzpyrite alteration; 4) surrounding decarbonatized and intensely argillized waste and leach grade ore; 5) pervasively decarbonatized waste rock; and 6) peripheral waste with weak decarbonatization and local propylitic alteration. Zoned alteration extends as much as 1500 m beyond orebodies.Understanding Blue Star subdistrict zoned alteration assemblages and gold grades has increased geologists' ability to provide practical and economically significant information to geotechnical engineers, mine planners and drill and blast personnel. Alteration influences geotechnical pitslope design because each assemblage has distinct rock strength. Geotechnical engineers use three-dimensional models of incompetent alteration types as a foundation for pit-slope design. In the drill and blast cycle, hard and soft alteration types require modified practices (powder column, blast hole spacing, delay design etc.) for optimum blast energy distribution. Further, geotechnically instable alteration types require careful blast procedures to prevent backbreak whic~ damages ultimate walls. In addition to mine planning and mining applications, zoned alteration assemblages extending beyond orebodies provide a useful exploration guide. Metallurgical character also varies with alteration type. Intensely quartz-sericite-pyrite altered or silicified ore has relatively high partical-size dependency and poor leach recoveries. Moderately sericite-kaolinite-quartz-pyrite altered rock, in contrast, shows little size dependency and good leach recoveries.The author sincerely thanks L. Schutz, P. Williams, C. Clode, W. Trudell, P. Herrera, M.DKunkel, M. Goings and numerous other Newmont geologists, metallurgist, engineers and support staff who made this paper possible."

Jan 1, 1997

By Min Chen, Cui-huan Huang, Zhen Tian, Jian-hong Dong

"The present work studied the production of Fe-Si-Mn alloy from adjusted converter slag by thermodynamic analysis. The results showed that solubility of SiO2 in the molten slag increased with increment of temperature, and it is about 80% at 1800 ?. With increment of SiO2 content, a(MnO) and a(CaO) decreased, and a(FeO) increased to the maximum when w(SiO2) is about 30%. As a result, the reduction of the slag was in the order of Fe?Mn?P before SiO2 reduction, the reduction order was Fe?P?Mn?Si when SiO2 content in the slag was from 46.4% to 54.2%, and changed to Fe?Si?P?Mn when SiO2 content exceeded 54.2%. The mass fraction of Si in the alloy phase increases with increasing of w(SiO2) in the slag, and the mass fraction of Si in the alloy reached to 62.2% at 1800 ?.IntroductionFerroalloy production is a high energy consumption and high pollution industry[1-2]. If ferroalloy production could be produced from molten slag by addition of carbon-reducing agent, the valuable metal and oxide in the slag can be recycled, most importantly, if the high-temperature resource carried by molten slag can be made full use in the field of ferroalloy production, the power consumption of ferroalloy production could be cut down greatly.Converter steel slag is a kind of byproduct in steelmaking processing increasing rapidly with the increment of crude steel, but the utilization ratio is low. Most heat recovery research is still in the experimental stage except the heat recovery of blast furnace slag by water quenching method, at present[3-4]. It is of great significance for enterprises to energy saving and emission reduction if the molten steel slag could be utilized directly. Not only the reuse methods of liquid steel slag material can be promoted, but also the use of heat carried in the slag could be achieved. The basicity of converter slag is high and the activity of SiO2 is low so the reduction of SiO2 in the slag is little. The compositions of slag and metal phases were calculated by Factsage program on different conditions to explore the reduction of converter slag for recovery of valuable metals and an efficient new way to use the high-temperature heat combining with the current reuse and research status of converter slag. Further, the improvement of components activity in slag and the increase of Si concentration in the metal were also dicussed."

Jan 1, 2012

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

The carbon composite brick is a new refractory used in blast furnace hearth and bottom. It caused wide attention due to its high thermal conductivity and low erosion by molten iron. In this paper, chemical constituents, SEM-EDS and X-ray diffraction were carried out in order to understand reaction mechanisms. A series of experiments of oxidation resistance characteristics were made. The oxidation mechanisms of carbon composite bricks in the presence of air were analyzed. According to the analysis on many experimental results, the oxidation process of carbon composite bricks under different temperatures were controlled by different mechanisms. In the condition of high temperature, SiO2 as oxidation product hindered the diffusion of O2, and reduced the oxidation loss of graphite in the internal.

Jan 1, 2015