Search Documents

By XING Xiangdong, Zhang Jianliang, MA Jinfang, WANG Zhenyang

The non-equilibrium reflux reaction behavior of phosphorus was studied with synthetic slags formed by using the AR chemical reagents and changing the initial condition of basicity, FeO, MgO and Al2O3. Due to increase of viscosity, the dephosphorization slag with high basicity inhibits the full contact of slag with iron, which leads to the low reaction rate in the early stage. However, since the high basicity improves the activity coefficient of CaO, the dephosphorization rate and phosphorus capacity goes up in late reaction stage. FeO promotes the increase of reaction rate in early dephosphorization stage. But the polarization force of Fe2+ is stronger than Ca2+, which hinders the reaction between phosphate ion and CaO and reduces the stability of PO4 3-. Thus, high content of FeO will adversely impact on dephosphorization reaction. In addition, MgO has a promoting effect to the dephosphorization, whereas Al2O3 has a negative influence.

Jan 1, 2016

By Dr. -Ing. Wolfgang Pietsch

Many primary metallurgical wastes are in the sh.-ape of turnings; borings, chips, dusts, and other particuletes. While such. materials can be easily segregated and/or upgraded to yield high quality ?secondary metals with often known composition for easy recirculation into the production? process; their particulate nature results in various problems. Roller presses are used in an ever increasing number for size enlargement and densification of primary particulate metallurgical wastes for secondary metal recycling. The paper will mention the areas of application from A(luminum) to Z(ink), also including Brass; Cast Iron, lead, and Stainless Steel, as well as dusts from all types of melting and ladle furnaces or converters. Typical systems using roller presses for size enlargement. will be discussed.

Jan 1, 1995

By Amy Nelson

In the electrolytic production of zinc, cobalt is removed from the zinc electrolyte by cementation with zinc dust prior to electrowinning. Although the thermodynamics for this reaction are favourable, kinetic barriers to cobalt reduction render the method almost useless in practice unless activators such as copper and antimony or arsenic are added. There is a large body of work studying the effect of these additives, yet the mechanism by which they act is still poorly understood. Even when the target conditions are met, zinc dust consumption is excessively high: satisfactory operation requires up to 300 times the stoichiometric amount of zinc dust. The objective of this work is three-fold: (1) to examine the effects of activators and elucidate the characteristics that make a good activator; (2) to identify new additives that could lead to a more efficient purification process; and (3) to test the new additives with synthetic and real electrolyte solutions. The present paper gives a status report on this project.

Jan 1, 1998

By Shuai Wang, Gang-hua Fu, Lu Yang, Yu-feng Guo, Tao Jiang

The fluorine-bearing iron concentrate is one of the refractory raw materials for pelletization, which is mainly used in Baotou iron and steel company with lots of problems, such as narrow roasting temperature range and low compressive strength of products. According to its specific character, the effects of roasting temperature, time on the compressive strength and microstructure of pellets were researched. The results show that low melting substances formed during the roasting was the dominant reason of those problems. High melting substances were added in the roasting to investigate their effects on the roasting properties of fluorine-bearing iron concentrate pellets. Low melting substances were reduced when chromite was added. The compressive strength of products was 3100N/P when the 2% chromite was added at the roasting temperature of 1150 ºC, which was increased 700 N/P compared with the pellets without chromite, and the roasting temperature range was expanded by 170 ºC.

Jan 1, 2016

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a'=0.407 nm for two axes and c'=0.390 nm for the third axis. The a'axis is shorter by 4% than the c'axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By J. R. Hartin

Traditionally, many of the advances in casting technology have been made by expensive and time consuming trial-and-error methodology. Modeling of the complex solidification process promises production of castings which are made "right the first time." Even though several models are available for simulation of conventional casting processes, none of them address this relatively new technology of investment cast titanium aluminides. In this paper, modification and application of a transient, three-dimensional, fully coupled fluid flow and heat transfer solidification modeling computer program to the analysis of centrifugally cast titanium aluminides is discussed. The predictive results of the program are compared to qualities of actual cast parts for validation.

Jan 1, 1992

By Mansoor Barati, Leili Tafaghodi Khajavi

"This study involves employing solvent refining as a purification process in which silicon recrystallization takes place from an iron-silicon melt. It is believed that iron will act as the impurity “getter” and purified silicon crystals will grow from the alloy melt, while the impurities are segregated to the liquid alloy. Phosphorous is a problematic impurity to remove since its segregation coefficient in pure silicon is relatively large. To assess the feasibility and efficiency of phosphorous removal through solvent refining, it is critical to study its equilibrium distribution between solid Si and the Fe–Si alloy phase.The distribution of phosphorous between solid silicon and iron-silicon melt at 1210-1310 °C was measured to evaluate the impurity removal potential of each alloy. Interaction parameter between phosphorous and iron was calculated by varying the concentration of phosphorous in silicon.IntroductionAmong various semiconductor materials for manufacture of solar cells, silicon accounts for over 90 percent of today's PV materials [1, 2].The major challenge in producing solar silicon that operates efficiently is to meet purity level requirement through a cost efficient route. Silicon solar cells can play a significant role in answering the world's need for energy if cost reductions can be achieved through manufacturing process. Considerable effort has been made to replace the expensive, complex vapor-phase purification by a simpler and less costly process. One of the refining approaches that have attracted wide research interests is producing low-cost solar grade silicon by purification of metallurgical grade silicon. Since metallurgical processes are selective in removing impurities, a combination of various purification processes can be used to reduce the impurity level in silicon. Considering different thermodynamic characteristics of impurities, each refining step is responsible for lowering specific impurities."

Jan 1, 2012

By Demaerel. J. P.

Arsenic plays a major role during electroreflning of copper. Both the arsenic content in the anode and the arsenic concentration of the electrolyte have, in conjunction with other impurities such as lead, antimony, bismuth and oxygen, a direct influence on the quality of the cathode. The mechanisms are currently slime. inclusion and precipitation of insoluble compounds in the bulk of the electrolyte. Arsenic has also been reported to have a depassivating effect on the anode. An influence on the anode slime adhesion has also been found. A literature survey is given and these data are compared with and completed by our own results based on lab and pilot scale experiments as well as on Olen tank.house practice.

Jan 1, 1987

By Hoda Emami

In this study, a combined pyrometallurgical and hydrometallurgical technique has been designed and used to recover rare earth mixture elements (REE) and cobalt from a NdFeB magnetic waste. while addressing the cost of reagent and process facility. This process can be adjusted to different magnetic wastes regardless of their compositions. Prior to the leaching, the magnet scrap was pretreated by two rounds of roasting (750°C in air) and a mechanical grinding in between, to convert iron metal to ferric oxide. Subsequent leaching was performed using optimized conditions (pH, temperature and retention time) where the extraction ratio of REE to Fe III is the highest. After removing iron content from the leachate (pH ≈ 3), REE was precipitated selectively and purified further. The produced REE concentrate reaches 99% purity with 85% recovery in a single run. The cobalt oxide was isolated from the PLS as a by-product with 99.8% purity.

By V. P. Bystrov

Vanyukov process has been developed and investigated in Russia over the last 25 years. It has been established that various kind of material could be treated in Vanyukov process. The results of the pilot plant trials as well as industrial experience are presented in this paper.

Jan 1, 1993

By Renato G. Bautista

"The development of processing methods for the preparation .of three electronic materials with rare-earth components is discussed. The resulting processing innovations are the results of a search for an economically competitive pilot scale or industrial production flowsheet without compromising the required properties of the final products. The three cases highlighted in this presentation are: 1) The preparation of high energy (Pr-Nd-Ce)FeB magnets for MRI application from a mixed-rare-earth oxide with a narrow range of composition directly prepared from the solvent extraction circuit of bastnaesite ore. 2) The kg production of the giant magnetocaloric effect Gds(SixGe1-x)4 magnetic refrigerant materials from commercial grade gadolinium metal (95 to 98 at. % pure) instead of high purity gadolinium metal (99.8 at. %); and 3). An industrial chemical synthesis flowsheet for the production of the superconductor precursor of YBa2Cu3O7.INTRODUCTIONIn the laboratory discovery stage, the synthesis of a new material is carried out using very high purity components, usually the highest purity available. As the new material is studied and characterized, the effectiveness of its desirable properties becomes better defined and understood. The evaluation of the effectiveness of the .property over the range of a given parameter and other interactions are further studied. Once it's potential application becomes clear, a practical and economical processing method need to be developed. The successful material processing flow sheet does not necessarily have to be a scale up of the laboratory procedure. At this stage, substitution of starting components and with lower purity materials is considered as the economics of the processing becomes a major issue. In addition, other approach to it's synthesis"

Jan 1, 2000

By Shaohua Ju, Jin-hui Peng, Ya-jian Wang, Shuai-dan Lu, Li-bo Zhang, Lei Guo

"The granulation of a red mud is of great importance for recycling this material as an adsorbent for waste water or gas. A new granulating process was developed and its effect was evaluated. To reduce the cost of the granulation process, the wet filter cake (containing 25% water) was directly mixed with different cement contents (4%, 6%, 8% and 10% based on wet material). The mixtures were placed in a moist environment for 4 days, and then were washed with deionized water until the pH values of leachants were lower than 9.0. The efflorescence ratio, surface area and particle size of the aged mixture were determined, respectively, by bottle shaking experiments, N2 adsorption and screening. The results showed that the best addition of cement is 2%, and this yielded granulated material with a particle size of less than 2 mm, an efflorescence ratio of 4.83% and a specific surface area of 17.42 m2/g.IntroductionRed mud is a residue of the aluminium industry that is produced during the alkaline extraction of alumina from bauxite by the Bayer process. For every ton of alumina that is produced, the amount of red mud generated can vary from 0.3 to 2.5 tons, depending on the characteristics of the bauxite. In its typical form, red mud is brick red in colour, caustic, about three times as dense as water and, when un-neutralised, has a high pH, typically around pH 13 [1]. It is primarily composed of iron oxide, silica and alumina, along with traces of heavy metals. Red mud particles are quite small; typically 99% will pass through a 0.6 mm sieve and 87% through a 0.038 mm sieve [2],"

Jan 1, 2012

By Shadia J. Ikhmayies

SnO2:F/CdS:In bilayers were produced by the spray pyrolysis technique on glass substrates. The structures were characterized by recording and investigating their transmittance curves, I-V plots, X-ray difractograms (XRD) and by observing their scanning electron microscope (SEM) images. From the I-V plots it was found that the SnO2:F forms an ohmic or quasi-ohmic contact with CdS:In. XRD patterns show the polycrystalline nature of the films and show that there is a small shift in the position of the (200) line of SnO2:F without the appearance of new peaks. The morphology of the structures are compared with those of SnO2:F alone and CdS:In alone on glass substrates.

Jan 1, 2009

By N. S. Narayanan

Monazite, one of the major sources of rare earths, is normally opened by digestion with hot concentrated caustic soda solution. Caustic digestion dissolves phosphate and leaves a hydrated mixed metal oxides cake containing thorium, uranium and rare earths. By leaching this cake with hydrochloric acid at pH 3.0 to 3.2 bulk of the rare earths are preferentially removed and separated. The slurry left after removal of major portion of rare earths contains all the thorium and uranium present In the feed monazite. In addition this slurry also contains substantial quantities of rare earths. Solvent extraction tests were carried out to develop a process to separate rare earths, thorium and uranium present in the mixed chloride solution obtained by dissolving the above slurry in hydrochloric acid. Based on these tests a solvent extraction flow sheet was developed with di-2-ethyl hexyl phosphonic acid mono 2-ethyl hexyl ester as the extractant. The details of experimental work and results obtained are discussed and a flow sheet for processing monazite Incorporating the new process is suggested.

Jan 1, 1997

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Kathryn A. Mrotek

The textural growth patterns of nodules from two areas in the North Pacific and the South Pacific are characterized by mottled, columnar and compact-type zones. Amorphous material (mainly iron and manganese hydrox-ides) is a botryoidal-forming phase in the mottled and columnar zones. Crystalline material (platy crystals of birnessite and crystallites of todo-rokite) is found primarily in the mottled zones on botryoidal structures or as long-protruding structures growing onto that portion of the nodule in contact with the underlying sediments. The long-protruding mottled zones contain little or no biogenic debris, suggesting that these zones grew un-interruptedly within the underlying sediments. The coalition of spheroidal knobs comprising some of the nodules also suggests a relatively long residing time within the sediments. It appears that crystalline material (the usual host to associated valuable metals) forms in a quiet environment and as a result of direct nodule association with the underlying sediments.

Jan 1, 1982

By Barry J. Welch

The production of primary aluminium can potentially lead to metal that, with minimum treatment, meets a high purity standard. Smelters that can achieve a significant proportion of their production in this manner have a competitive edge which is of growing importance as the use grows for such items as compact discs and the like. Superimposed on the desire to produce high quality metal are stringent environmental requirements that the industry must adhere to. The environmental 'legislation focuses on fluoride emissions and the approach adopted is towards a zero waste management philosophy. The fluoride recycling process does, however, result in volatile impurities being captured and recycled to the cell. Aluminium has an extremely high reduction potential and this results in a significant proportion of the recycled impurities being reduced at the electrolyte metal interface and thus contaminating the metal. This paper reviews sources of impurities and the impact of the operating procedures adopted on metal treatment.

Jan 1, 1996

By LuisW. Pommier

The industrial wastes generated by the plating industry, the circuit board manufacturing industries and other related industries normally contain high concentrations of metals, which make them hazardous. The extraction of the contained metals and their separation may be achieved by both pyro and hydro metallurgical processes. Some of the industrial wastes, those rich in some metals like nickel for instance, are being treated like mine ore concentrates and are being fed to smelting furnaces. The slags from these smelter operations are hazardous. They have, however, special environmental dispensations issued by the regulatory authorities. Hydro-metallurflcal processes have been reported. They also generate a residue which is hazardous because not all the valuable metals are leached out and also, because "non valuable" components, like chromium, are less readily leached. Residues from the plating industry, containing nickel, copper. zinc, iron and chromium as the major constituents and also sodium and calcium, together with cadmium, cobalt, lead. manganese, magnesium, molybdenum, and potassium, have been processed for the extraction of the valuable components. The generation of electrolytic nickel, copper and zinc and also of ferric chloride and chromium oxide is reported. The operation is achieved by a caustic leach for the extraction of zinc, followed by a sulfuric acid leach for the extraction of nickel and copper. This acid leach also extracts the iron and some chromium. The nickel copper and zinc are rendered pure by electrolysis, the iron is oxidized for the production of ferric chloride and the chromium is recovered as an oxide. The leaching operation is performed in two stages, first at a pH of 2.5 to generate an electrolyte for the partial recovery of the metals and then at a pH of 0.5 for the complete extraction of the metals. This leaching operation generates a residue, which although small in volume compared to the initial feed, still contains traces of the valuable metals and a portion of the chromium which makes it hazardous. Additional leaching with hydrochloric acid or nitric acid is required for its complete dissolution. The other minor constituents mentioned are present in concentrations each of less than 0.1% and are handled as impurities in the process. The metals which are soluble at a pH 0.5 and precipitate between 0.5 and 2.0 are bled off. Other impurities will concentrate on the raffinate from the solvent extraction operations from whence they are bled off. These bleeding streams are hazardous and the "impurity metals" are now present in concentrations which would make them valuable, however, the size of these streams is so small that they do not warrant their processing, however they could be marketed to specialized smelters. The extraction of the valuable metals, of the hazardous constituents, the generation of a marketable mixture of minor constituents and the production of a non-hazardous residue for declassification is profitably achieved.

Jan 1, 1998

By Kim Verbeken, Evelien Van de Steene, Marc Verhaege, Jeriffa De Clercq

"AbstractThe industry is confronted with stricter discharge levels and an increasing awareness to avoid toxic waste (such as heavy metal containing sludge obtained in physicochemical water treatment) and recover valuable metals. This can be realized by ion exchange or by electrodeposition. Both techniques however show an optimum concentration range to efficiently remove and/or recover metals: electrolysis can recover the metal in its metallic form but suffers from low efficiency when applied to diluted solutions, whereas ion exchange can only be applied economically in the low ppm range.A combination of ion exchange followed by electrodeposition was applied to an industrial wastewater. The strong acidic ion exchange resin was stripped with H2SO4 giving a solution of 9g/L nickel. From this solution, nickel was electrodeposited in an ammonia buffer on a Ti-mesh cathode with high current efficiency. It is shown that organic compounds (surfactants, brighteners, …) present in the industrial wastewater do not influence the recovery process.IntroductionAlmost all rinse waters emerging from metal plating plants are generated during the washing operation of plated materials. These solutions with low metal content must either be recycled within the process or be discarded to the surface water after decreasing their metal content to acceptable levels determined by the local environmental regulations, which become more and more stringent. Today, the most commonly used practice is a physico-chemical treatment (precipitation) and a resin post treatment to meet the standards. A more sustainable approach should use a technology to recover efficiently the metal or metal salt without the production of sludge and the effluent should be consistent with environmental regulations."

Jan 1, 2008

By G. R. Waters

NMR360 is developing a suite of chloride-based metals extraction processes, with the first commercial operation scheduled for commissioning late in 2018. It is critical, therefore, that with the introduction of any new technology, that the circuits do not suffer from mechanical failures which will compromise the operation. Although chloride leaching is at atmospheric pressure and relatively low temperature, the main challenge is preventing corrosion, since the high proton activity makes even a small amount of acid behaves as though it were concentrated. An additional challenge in concentrated chloride circuits is the potential for solids precipitation. In this context, therefore, correct valve selection is crucial, and NMR360 has partnered with CGIS to ensure that the Severe Service Valves (SSVs) needed will perform over and above the definitions of the Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry. This paper outlines what the minimum requirements are for SSVs in chloride leaching applications, drawing on five decades of industry experience from one of Canada’s leading valve experts.