Search Documents

By Yuanbo Zhang, Zhixiong You, Zijian Su, Bingbing Liu, Guanghui Li, Guang Yang, Tao Jiang

Sodium stannate is widely used in the electroplating and tin alloy industry. But the traditional processes for sodium stannate production are characterized by long flowsheet, high production cost and strict requirement for the equipments, etc. In this study, a novel process for sodium stannate preparation from cassiterite concentrate and sodium carbonate via roasting in CO/CO2 mixed gas then followed by leaching was developed. The effects of roasting parameters on the Sn leaching efficiency were conducted. A Sn leaching efficiency of 77.2% was obtained under the optimal conditions. Sodium stannate (Na2SnO3·3H2O) with a purity of 95.8% was produced by the new process, which is better than that specified for the industrial first-grade product.

Jan 1, 2014

By Chai Li-yuan

The anodic behavior of AZ31 magnesium alloy in NaOH alkaline solution was investigated in this paper. The effects of anodizing parameters, such as applied current density, concentration of NaOH and temperature of the solution on the formation, structure and surface morphology of the anodic films were also studied. The formation of the anodic film was analyzed by analyzing the anodic polarization curves, the potential-time curves and XRD, SEM graphs of samples obtained at different anodizing time. The results of corrosion resistance tests, XRD and SEM observation showed that the temperature greatly affected the formation and anti-corrosion property of the anodic film, but the concentration of NaOH not. The film with best anti-corrosion resistance was obtained at applied current density of 10mA/cm2, 353k in 1mol/l NaOH solution.

Jan 1, 2006

By Tadashi Aiura, Yasuhiro Miura

"A small amount(0.2mass%) of Scandium(Sc) was added to the 7.NOl and 5083 Al alloys as a refiner and stabilizer of microstructure, and the resulting microstructures were discussed in comparison with the effects of the conventional additives. The followings are summarized: 1) in the as-solidified structure, a ·decreased tendency of constitutional supercooling and increased solubility of Mg were recognized for the Sc-added 5083 alloy. Sc is a -better microstructure refiner for the 7N01 alloy than Zr, in a sense that it does not suppress the favorable effect of· coexisting Ti. 2) Sc effectively suppresses recrystallization both in the 5083 and 7N01 alloys. 3) The rod like primary Al3Sc crystals formed during solidification, as well as the fine dispersion of Al3Sc precipitates formed by subsequent heat treatment, can act as a strong recrystallization suppresser. IntroductionThe 7N01 and 5083 alloys are the most popular industrial Al alloys and they are widely' used for various structures because of their superior properties. Fine macro and micro structures of the materials are required for obtaining acceptable sec resistance,consistent appearance of anodized surface and good weldability, as well as good mechanical properties. In order to produce fine grain structures, transition metals, such as Cr, Zr, and Mn, have been conventionally added.It has been reported that Sc is an efficient refiner [l, 2] and can be an alternative for the conventional and also suppresses recrystallization in Al alloys [3,4]. Scandium is the lightest transition element and forms an equilibrium intermetallic phase. The equilibrium phase, Ll2-Al3Sc, is coherent with the matrix, and of _spherical shape. A fine dispersion of the spherical precipitates is obtained by quenching and aging after solutionizing annealing. The authors have already reported a part of the experimental results on the effect of Sc on the as homogenized microstructure of the 5083 alloy [5]. In the present study, the effects of Sc on the macro and micro structures of the industrial high strength Al alloys(7N01 and 5083) for extrusion are investigated, and the superior role of Sc as a grain refiner is shown"

Jan 1, 2000

By Catherine Williams-Beam

Thallium is more toxic to humans than mercury, cadmium, lead, copper or zinc. Its chemical behavior resembles the alkali metals (K, Rb, Cs). It occurs almost exclusively in natural waters the monovalent thallous cation. The solubilities of thallous compounds are relatively high so that monovalent thallium is readily transported through aqueous routes into the environment. The major sources of thallium are the base metal sulfides and precious metal bearing sulfides. Therefore, it is often present as a contaminant constituent in waters emanating from heavy metal sulfide bearing deposits. Thallium can be effectively removed from wastewater to <2 µg/L by reductive precipitation of thallium sulfide. Effective thallium sulfide precipitation requires a controlled solution potential/pH combination. The required potential can be effectively achieved by utilizing a particulate iron slurry or packed column environment. Experimental results will be presented and discussed.

Jan 1, 2003

By Caisa Samuelsson

Experimental studies in laboratory-scale equipment have been carried out to study the vaporisation from dust generated during the copper converting process. In the present work the vaporisation of Zn, Pb, As, Sb, and Bi from a dust collected in the electrostatic precipitator after the copper converter were studied. The results show that Pb, Bi and As were vaporised to a high degree from the dust at a temperature above 900°C in a gas containing N2, SO2 and a small amount of H2. The vaporisation was high for these elements also in a gas containing N2, SO2 and 02 at temperatures above 1120°C. In an earlier study, thermodynamic calculations showed that it is possible to selectively condense metals at high temperature&apos; in a gas atmosphere generated during a copper converting process. The present study was carried out to verify the thermodynamic model. The results indicate that it should be possible for a selective condensation of Zn at high temperature. The temperature required for a selective condensation of Zn is dependent upon the gas atmosphere, e.g., the oxygen potential.

Jan 1, 1998

By Gaifeng Xue, Lei Zhang, Xia Liu, Lina Wang, Pu Liu, Benquan Fu

"Experiments were conducted to investigate the behavior of the integrated process with a three-dimensional electrode reactor combined with Fenton process for coking wastewater treatment. Effects of initial pH value, reaction time, H20 2 dosage, Fe2+ dosage on Total organic carbon (f OC) removal rate were investigated. The kinetics of degradation of TOC from coking wastewater by three-dimensional fluid bed electrode reactor combined with Fenton process was also studied. Experimental results shows that three-dimensional fluid bed electrode reactor combined with Fenton process had better synergic effect, average 17.4% TOC removal rate was improved within an hour. It was found that TOC degradation in coking wastewater followed a pseudo-first-order reaction kinetic model. The optimum degradation efficiencies of TOC were up to 60% as pH3.4, 3.5 mM ofFe2+ andl.2-1.8ml/L H20 2 in 90min reaction period. Furthermore, the integrated process showed a rapid reaction performance at a low temperature within a short reaction time and remained high efficiencies for TOC removal. Overall, the integrated process was proved feasible for coking wastewater treatment in practical applications.IntroductionCoking wastewater is generated from coal coking, coal gas purification, and by-product recovery processes of coking, which is composed of phenolic compounds, heterocyclic compounds, polycyclic aromatic hydrocarbons, ammonia, cyanide, polycyclic nitrogen-containing aromatics, acyclic compounds, etc. Most of these constituents are refractory, poor biodegradability, toxic and carcinogenic['-31. Currently, coking wastewater is usually treated by different forms of A/O biological nitrogen removal process as the primary treatment process, but the aforementioned processes are not efficient enough to meet the requirements from the National Discharge Standard in China (GB13456-1992). According to the continuous requirement on improving environmental protection for coking industry (revised 2008), increasing wastewater utilization ratio and reducing discharge of effluent in the coke industry has to be implemented for cleaner production and sustainable development. Therefore, advanced technologies need to be developed to treat coking wastewater and reutilize the product as industrial cooling water, which would be one of the best choices to achieve zero discharge of wastewater and reduce water consumption per ton of steel [4-51 . In this study, three-dimensional fluidized bed electrode reactor combined with Fenton process was adopted to advanced treatment of coking wastewater, and the effects of operating conditions, including H2O 2 dosage, Fe2+ dosage, initial pH, and reaction time on TOC removal rate, were investigated. Meantime, study of kinetics of reaction was estimated."

Jan 1, 2013

By Flávia Paulucci Cianga Silvas, Otávio da Fonseca Martins Gomes, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Guilherme Apostólico Bortolini, Stoyan Gaydardzhiev

"Printed circuit boards (PCB) are particularly problematic to recycle because of the heterogeneous mix of organic materials, metals, and glass fiber. PCBs are found in almost every electroelectronic equipment and their recycling process involves a pre-treatment to separate the products which contain targeted metals. In this work, a physical processing involving sequential shredding and hanuner milling were used to obtain a comminuted sample from scrap printers PCBs. The thus prepared sample was analyzed for particle size distribution and by optical microscopy as well was subjected to pyrolysis, leachabilty and chemical composition determination by XRF. The metals concentration was determined by ICP and AAS. The PCBs have been also analyzed by SEM-EDS (micro-analysis and X-ray mapping). The results show that the studied PCBs are lead free, multilayer with 4 copper layers, have 45% of metals and the copper is present in significantly higher concentration than the rest of the metals.IntroductionThe global generation of e-waste (electrical and electronic equipment waste - WEEEs) grows at a rate of about 40 millions of tons per year [ l].Among this e-waste there are PCBs that are present in almost all electronic equipment. Their composition is heterogeneous and varies according to several factors, including: kind of EEE, when and where it was produced, fabrication technology [2], etc. In printers, the PCBs represent about 6.6- 8 wt.% [3].The PCBs treatment may include physical, pyrometallurgical, hydrometallurgical, ectrometallurgical and more recently bio-hydrometallurgical process. Normally there is a combination between these processes [2, 4, 5, 6, 7, 8, 9, 10].The diversity between the different PCBs composition complicates the recycling process since the composition of metal and others materials can vary according to the models. So characterization is an indispensable step before any processing of PCB to begin. Owing to the above said, the main goal of this work has been set to characterize representative samples of PCBs from printers through physical, chemical and microstructural analyses."

Jan 1, 2014

By Katsuyoshi Tatenuma

"In order to mitigate the effect of global warming by preventing the accumulation of atmospheric CO2, a permanent fixation method of surplus CO2 as an insoluble mineral onto the sea bottom is proposed. As the proposed reduction method of atmospheric CO2, the concrete concept of this method is to form an insoluble carbonate mineral (CaCO3) by direct electrolysis of the seawater; Ca2++2HCO3 -+OH- ? ?CaCO3(insoluble)+CO3 2- (soluble)+H++H2O <not as coral reef reaction>, are directly disposed of itself onto the sea bottom. By this treatment, a concentration of carbonate is reduced in the section of superficial seawater, and therefore the absorption capacity of atmospheric CO2 increases depending upon the shift of chemical carbon equilibrium between the mass of superficial seawater and the atmosphere. As no additives are required, or no secondary waste are produced, the proposed method assuming as green-orientated, has possibility to resolve fundamentally the problem of global warming in a green orientate manner.IntroductionRecently, the amount of atmospheric CO2 has been exponentially increasing and it is a main greenhouse effect gas causing the global warming [1, 2]. The concentration of atmospheric CO2 has increased more than 30% (370ppm in 2001) during only last two centuries, therefore approximately 750 Gton-C of CO2 currently exist in the atmosphere, in which 180 Gton-C of CO2 are accounted for the increment during two centuries [1, 3, 4]. In order to avoid the progressive increase of CO2 global abundance, 3 Gton-C of the incrementing amount per year [4], have to be removed annually from the atmosphere."

Jan 1, 2008

By J. D. Miller

Low-level radioactive contaminated soils (10-500 pci/gm) created by defense-related activities at certain superfund sites, such as Nevada Test Site (NTS), is a current environmental concern. Many of these contaminated sites may require appropriate cleanup and restoration, which could cost billions of dollars and put tremendous pressure on our limited financial resources. Therefore, the development of a selective flotation process to separate such radionuclides from contaminated soils should be considered. In this study, both a pure depleted UO2 sample and three synthetic UO2/soil mixtures were used to evaluate surface chemistry features and to examine the possibility for the flotation of fine UO2 particles from selected soils. It was intended that this model system would be a reasonable representation of contaminated soils such as those found at the Nevada Test Site which are reported to be contaminated by PuO2 fallout. The effect of reagent schedule, particle size distribution, and surface charge are discussed with respect to the flotation separation of the UO2/soil mixtures. It was found that both commercial fatty acids and reagent grade sodium oleate are effective collectors for UO2 flotation provided the pH is adjusted to the range of pH 8-9. The bench-scale flotation results successfully demonstrated that froth flotation technology can be used to remove UO2 from such model contaminated soils with appropriate flotation chemistry conditions which depend on the soil characteristics and other pretreatment procedures. In the best case, 90.2% of the UO2 was removed from a UO2/NTS soil mixture (119 ppm UO2) and the soil reduced in UO2 contamination from 119 ppm to 17 ppm in a single stage bench flotation. The impact of clay slimes present in the soil is revealed by the results which show that, for example, for a deslimed soil (28x400 mesh and 100 mg UO2/kg soil) 85¬90% UO2 recovery can be obtained with a reduction in contamination to 4.6 mg U02/kg soil.

Jan 1, 1995

By Zeng Zheng, Liu Chen, Yu Xing-Fu, Tian Su-Gui, Zhang Chao

"Single crystal nickel-base superalloy is prepared by using the various withdrawing rates. By measuring creep properties and microstructure observation, the influence of the element segregation on creep properties of the superalloys is investigated. Results show that the dendrite spacing and the segregation extent of the elements decrease with the enhancing withdrawing rate. The superalloy with smaller dendrite spacing has lower segregation of the elements and better creep resistance. The dislocations climbing over the rafted y’ phase is thought to be the deformation mechanism of the alloy during steady state creep. In the later stage of creep, the fact that some dislocations shear into the rafted y’ phase may twist the rafted y’ phase. As the creep goes on, the initiation and propagation of the cracks occur up to occurring creep fracture, which is thought to be the fracture mechanism of the superalloy during creep.1. IntroductionSingle crystal nickel-based superalloys consist of high volume fraction of ?? strengthening phase and ? matrix, and possess the excellent high-temperature mechanical and creep properties, therefore, they have become the main material to make the blades of the advanced aeroengines[1-3]. Some literatures report that the temperature-bearing and creep-resistance properties of the single crystal nickel-based superalloys can be remarkably improved as the increases content of the refractory elements, such as W and Re[4-6]."

Jan 1, 2012

By Shadia J. Ikhmayies

CdSxTe1-x and CdS1-yTey solid solutions are usually formed in the interfacial region in the CdS/CdT thin film solar cells during the deposition of the CdTe layer and/or the processing steps of the device. It is well known that CdCl2 heat treatment encourages the formation of the CdSxTe1-x alloy which improves the solar cell performance. In this work, indium doped CdS1- yTey thin films are produced by first producing CdS:In thin films by the spray pyrolysis (SP) technique on glass substrates, then annealing the films in nitrogen atmosphere in the presence of elemental tellurium. The films are characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and transmittance measurements. The transmittance is used to deduce the optical parameters such as; the extinction coefficient, refractive index, besides to the real and imaginary parts of the dielectric constant. The dispersion parameters such as Eo (single-oscillator energy) and Ed (dispersive energy) of the deposited films are also estimated and discussed.

Jan 1, 2015

By M. Hashimoto

The equilibrium distribution ratios of sulfur between molten copper and CaO-fluxes containing caF2 and caC12 were determined in the range of 1300° to 1400° C under carbon monoxide. The rate of approach to equilibrium is rapid and increases with increasing CaCll concentration. In CaO-CaFl-CaCl2 fluxes, the distribution ratio varies in a complex way with temperature and CaFl concentration. The results are compared with those obtained with the binary fluxes of CaO with BaFZ and MgFl ?

Jan 1, 1983

By M. Sakamoto, S. Karaswa, Y. Yoneoka, Y. Ohmizo

"The Annaka Refinery has been processing leach residue by Waelz process for 17 years. Recently, the quantity of the leach residue has increased due to a decline in the quality ~f zinc concentrate. Meanwhile, negative factors (e.g. deterioration of water balance due to improved electrolytic power consumption rate) have increased· in the processing of the leach residue.We have implemented various measures in responses to this situation, while striving to increase ·processing capacity and achieve stable operation. AS we have largely completed our assessment of the efficacy of these measures, we report on our recent process improvements.IntroductionWe have been treating leach residue by the Waelz kiln process since 1981. At that time, treatment of only 50,000 tons of leach residue per year was anticipated. However, subsequent process improvements have revised this figure up to 75,000 to 80,000 tons per year.However, today's increased Fe zinc concentrate grade has resulted in increased amounts of leach residue. In addition, improvements have reduced electrolytic power consumption rate of zinc electrolysis, limiting the amount of water that can be used in ·the zinc refining processes and for deaning leach residue. Consequently, we encounter an increasing number of problems and factors adversely affecting leach residue treatment, including increases in water-soluble Zn (WsZn) and. S (S04) in leach residue.To solve these problems, we have taken several measures to ensure long-term continuous operation and treatment of this increased · amount of leach residue. This paper discusses these measures."

Jan 1, 2000

By Bien Ferrer

In most smelting operations, there is a strong incentive to improve safety, reduce downtime and extend the campaigns of furnaces and related equipment. An asset management strategy that is based on information, rather than simple throughput metrics and intuition, can be developed to improve uptime and unlock value currently unrealized at existing smelters. Advances in digital technology, including data analysis, modelling and monitoring for hot pyro-metallurgical vessels, make it possible to assess the current condition of an asset, as well as to make more informed projections about its future condition, using on-line and historical data. This would allow practices around asset management to be more proactive and less reactive, with the end-result of optimized uptime. ‘Digital Asset Management’ describes a concept in which digital technology is used to support an asset management strategy and accelerate decision-making by providing information on what, why and how an asset should be designed, operated or maintained. With the overall goals of effective resource utilization, optimized operations, capital efficiency and social acceptance, Smelter 4.0 is a program of holistic improvement and is underpinned by the effective use of data to drive decisions. This paper focuses on Asset Reliability, which is one of the improvement pillars of Smelter 4.0, and introduces a methodology that is aimed at closing the gap between recorded data and evidence-based decision-making through Digital Asset Management.

By Lv Guozhi, Niu Liping, Liu Yan, Zhang Zhiqi, He Jicheng, Zhang Ting’an, Dou Zhihe

"CuCr alloy can be extensively used as contact materials in integrated circuit, electrodes, electric contact and high strength conductor. We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The slags and CuCr alloy were characterized respectively by XRD and SEM. The results show that when the additive is Na3AlF6, the slag consist of Al2O3 and Cr. When the additive is CaF2, the slag consist of Al2O3, Cr, CaF2 and CaAl4O7. The inclusions in CuCr alloy are mainly Al2O3 and pores which disperse in Cu-rich zone and Cu-Cr phase interface. When 5% CaF2 and 5% KClO3 are added, there are fewer pores and inclusions, and the more better microstructure.1 IntroduceCuCr alloy is the contact terminal material with an eximious properties[1,2], which gradually replaces CuBi alloy becoming the first choice for contact terminal material in the medium and high power vacuum switch after the 1970s. The traditional preparation methods of CuCr alloy mainly contain powder metallurgy, infiltration process and vacuum electric arc melting methods. But the above methods exist some shortcomings, such as poor product quality, high cost of production, processes complex ect[3-9]. CuCr alloy is made by the thermit reduction self-propagating method, which uses CuO, Cr2O3 and Al as raw material to get the high-temperature melt, and then casts to manufacture CuCr alloy ingot, which response equation follows as:"

Jan 1, 2012

By Pertti Koukkari

The novel Jarogain process combines treatment of the jarosite residue of zinc manufacturing and processing of arc furnace dust from steelmaking to a holistic recovery technology. The new hydrometallurgical approach is targeted to recover the major constituents (Fe, Zn, Pb) as well as valuable components such as Ag, Au, In and Ga from the jarosite-dust mixture as reusable concentrates. The fractionation process proposed by VTT and Aalto University takes advantage of jarosite being readily fine powder and directly available for wet chemical processing. Jarogain process provides an energy efficient opportunity for jarosite utilization as value added products. The experimental proof-of-concept of key stages of the process will be outlined with a comparison of available pyrometallurgical treatments of jarosite waste. The techno-economical assessment is based on estimated investment and variable production cost using the discounted cash flow (DCF) analysis.

By Joseph Hamuyuni, Pekka Taskinen

We present experimental results for the liquidus in the system Cu2O - CaO -Al2O3 at 1250 oC. In this study, we quantified the liquidus by the equilibration/quench/analysis technique, with Cu2O, Al2O3, and CaO as primary materials exclusively. Experiments were conducted in air at an at oxygen pressure (p) = 21.3 kPa). Equilibrated specimens were quenched in brine solution of 10 wt% NaCl. We then quantified the liquid chemical compositions by means of Energy-Dispersive X-Ray Spectroscopy (EDS) and Electron probe micro-analyzer (EPMA). This study reveals inconsistences in liquidus surface of the present ternary diagram of the system here in mentioned. Differences of up to 10 wt % compositions of the species have been observed.

Jan 1, 2015

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

By Cassandre Nowicki, Louis Gosselin, Carl Duchesne

"Quebec's primary aluminium production industry consumes roughly 39 TWh of electricity per year and is accountable for roughly 7 million tons of CO2 equivalent. By tapping only a small portion of waste heat and integrating it inside the production facility itself, we can significantly reduce GHG emissions and energy consumption. Although the amount of thermal waste can be adequately estimated by applying an energy balance to production processes, this provides very little information on the quality of waste heat and its potential for integration. A measure of exergy is required. Waste heat streams characterized by high exergy content may generally offer valuable incentives for recovery and integration. More generally, exergy values limit integration possibilities. An exergy analysis is provided for the aluminium electrolytic reduction process. This is meant to guide future heat recovery initiatives and energy efficiency measures.IntroductionCanada is one of the world leaders in primary aluminium production and 92% of its aluminium production capacities are located in the province of Quebec. In 2007, production capacity reached 2,786,000 tons in Quebec alone. Since it is estimated that 2.5 equivalent tons ofCO2 are released for each ton of aluminium produced in Canada, Quebec's aluminium production industry is accountable for roughly 7 million tons of CO2 yearly [1, 2]. Furthermore, with an average electricity consumption of 14 MWh per ton, primary aluminium accounts for 39 TWh of electricity per year in Quebec and this energy consumption represents 350 thousand tons ofCO2 equivalent [3, 4]. Natural gas consumption associated with primary aluminium production accounts for less than 1 TWh, but it represents an additional 350 thousand tons of CO2 equivalent [ 4].This work is meant to provide a tool to guide future efforts towards heat recovery and energy efficiency in the primary aluminium industry. Waste heat recovery and thermal integration can cut down both energy consumption costs and GHG emissions. In a primary aluminium production facility, waste heat represents roughly half of the energy input into the Hall-Heroult process. Tapping only a small portion of this energy could reduce natural gas and electricity consumption significantly. In order to evaluate how much of this energy is actually usable, we propose to apply an exergy analysis to individual transformation processes in an aluminium production facility, such that a potential to do work can be assigned to every waste heat flux. The approach will be described in the next section."

Jan 1, 2012

By Robert Fritzsch, Ragnhild E. Aune, Mark William Kennedy, Behzad Mirzaei

"The quantitative particle concentration can give important information about the cleanliness of melts for quality control in primary and secondary production of aluminum. Manual quantification of the particle concentration is normally a time consuming process and human control can bias the acquired images and particle count.The present paper explains the automated image-processing steps for the quantification of SiC-particles, with equivalent diameters from 2 to 25 µm, in solidified A356. A total of 700 micrographs, acquired with a standard white light microscope with 10 x magnification, were analyzed. The applied software (Image Pro-Plus 7.0 from MediaCybemetics®) allows for programming of macros which in tum provides the user with a higher degree of control. The automated results are compared with the results obtained by manually counting the particles in the same micrographs. The impact of the automated results on the estimated filtration efficiency was established to be only -3%.IntroductionInclusions are both indigenous and exogenous particulates that are present in commercial metals such as aluminum. If large individual or large numbers of inclusions are present, they can have a significant negative impact on the appearance, mechanical and chemical behavior of products produced from the metal. Aluminum is known to contain large numbers of inclusions: =50 µm in size, e.g. typically <l ppm by volume or <100,000 inclusions of>20 µm per kg of metal as detectable using a Liquid Metal Cleanliness Analyzer, LiMCA [1]. Depending on the final application of the aluminum, inclusions can render the metal 'not fit for purpose', and result in serious economic consequences to metal producers.It is not surprising that the aluminum industry has developed a number of treatment processes to improve metal cleanliness, given the large number of high value products whose quality can be adversely affected by inclusions. CFFs are the most commonly applied filtration process and have been used to filter >50% of the world production of aluminum since the 1990's [2].Inclusions in aluminum may be particles, bifilms [3] or clusters of: oxides (Al2O3 , SiO2), spinels (MgO· Al2O3), carbides (SiC, Al4C3), nitrides (AlN), borides (TiB2), sulfides, phosphides and intermetallics [ 4]."

Jan 1, 2013