Search Documents

By Jerry Wallace

Two recent-release boulders posed serious threats to public transportation and utilities in Washington State. Both required challenging drilling and blasting solutions.

Jan 1, 1997

By David Hersey

The Paseo Bridge was located at the I-29/I-35/US-71 Missouri River Highway Crossing. It was built between 1952 and 1954 by Massman Construction Company. The 1,232 foot long, self-anchored suspension bridge was the longest of its type when built. On Jan. 22, 2003, a connector pin designed to allow the bridge to expand and contract during temperature cycles seized and caused a portion of the bridge deck to raise up and block traffic. This marked the beginning of the end for the old Paseo Bridge.

Jan 1, 2013

By Dan McCutchen, Oettmeier

Kelly bar drilling and blasting is unique to Florida, the' Bahamas and other marine limestone areas in the world where blast holes are required but will not remain open for the loading of explosives. This type of rock formation usually yields 1.5 tons of recoverable rock compared to 2.2 tons per cubic yard for competent limestone. The loss of .7 tons per cubic yard is due to voids and sand in the formation. These deposits all contain water to the top of the blast holes which are collared only a few ft. above the ground water level. The working pit is a water filled lake which is excavated from the bank by draglines. These drills have been used in Florida for many years to depths of 65 ft or less.

Jan 1, 1991

By Calvin Konya, Steven S. Spagna, Ed Smith

During Summer 2001, the U.S Army Corps of Engineers awarded a contract to the construction firm of Bush and Burchett of Allen, Kentucky, for the purpose of developing a 13 acre redevelopment site by removing approximately 2.5 million cubic yards of rock (fig. 1). The Redevelopment Site will be the future home for a large portion of the City of Grundy, Virginia. Additional work items include the construction and relocation of 3,000 feet of the Norfolk Southern railroad bed, the placement of 95,000 cubic yards of fill and the placement of 16,000 cubic yards of stone slope protection along the Levisa Fork River. Bush and Burchett received a notice to proceed with construction in July 2001. Currently, the contract is near completion. Current activities include: hauling of material from the Redevelopment Site to the disposal area; placing fill material on the Redevelopment Site, and placing Stone Slope Protection (SSP) along the Levisa Fork river. Approximately one year into the construction highly weathered rock, degraded to near soil- like condition, was encountered in the upstream portion of the excavation. Over one-third of the original cut slope was adjusted and the blasting specifications had to be amended to accommodate for the material that was encountered in this area.

Jan 1, 2005

By P. N. Worsey, M. Schmidt

Many advanced military systems and civilian power generation concepts postulate the availability of compact sources of electrical power capable of delivering gigawatts over microsecond time scales. For example, such a compact power source is essential for future practical pulsed high-powered microwave sources. An explosive-driven flux-compression power generator (EDPG) could fill this requirement. A basic strength of this concept capitalizes on the inherent high energy density storage capacity of modern chemical explosives. It relies on the physics of magnetic flux compression to convert that stored chemical energy into very large amounts of electrical power over short time scales. The generator also has the additional advantage of employing the same types of explosives that are already routinely used in conventional munitions. However, the self-destructive nature of this type of power generator places serious limitations on power pulse-lengths and ranges of applications. This paper describes how a multi-disciplinary team led by researchers from the University of Missouri-Rolla (UMR), Texas Tech University (TTU), and Texas A&M University was awarded a grant by the U.S. Air Force Office of Scientific Research to perform basic research to resolve several fundamental EDPG problem areas. Described are the utilization of UMR’s extensive explosives research expertise and facilities to investigate questions of energy conversion efficiency and the mechanics of energy production. Also, UMR explosives researchers will provide inputs to improved dynamic computer models of the complex, intertwined physics and chemistry operative in these devices. In addition to explosives expertise, UMR provides facilities for basic explosives material research, as well as the storage, machining, and formulation of explosives. UMR researchers are also using test facilities and data collection equipment at the Rock Mechanics and Explosives Research Center and at the UMR Experimental Mine to perform “proof of principle” and subscale tests of explosive-driven flux-compression power generator components. An integral part of the paper is a description of the development of an extreme intensity flash system by UMR and TTU to allow for the high-speed photography of EDPGs in operation. This multi disciplinary research program offers major advances regarding the size, weight, and electrical characteristics of compact EPDGs. Such breakthroughs could dramatically accelerate the practical realization of systems currently under study. Also, these power sources may have far reaching relevance to other Department of Defense and certain commercial compact power applications.

Jan 1, 2000

By Y Nagendra, A. Ravi Kumar

A breakwater is a construction for protecting the marine structures like port, harbor, or anchorage-basin and berthed marine vessels from the destructive influence of the sea waves. The breakwater is constructed by using geologically competent, heavy, massive rock like granite, basalt etc having physical and mechanical properties within the limits specified by the designers. The construction requires boulders in varying sizes ranging from 0.5 kg to 20,000 kg. The stones from 0.5 to 1000 kg are called as core fill and boulders greater than 1000 kg are termed as armor blocks. These armor blocks cover and protect the core fill and prevent it from escaping. The requirement of armor blocks ranges between 25 to 35 %. The rest is core fill. However, the actual requirement depends on the breakwater design. In this context, the task of the mining engineer is to economically produce armor blocks and core from the designated quarry in right proportion with minimal losses. The whole bunch of engineering ingenuities should be put forth for obtaining the required armor blocks. The armor block production from any blast depends chiefly on geological conditions, bench dimensions and blast design. This paper is an attempt to bring out the various parameters affecting the performance of the blasting for armor block production using a case study.

Jan 1, 2005

By Ronald W. Roberts

For years, blasters have experienced near-misses, injuries, and yes, even fatalities as a result of the dangerous nature of our business. Yet, some blasters continue to portray the immortal attitude: nothing-would-or-could-ever-happened-to me syndrome. As we all know, that attitude can become disastrous to yourself or colleague(s).

Jan 1, 1996

By Lawrence Mirabelli, AngloGold Ashanti, Greg Gibson

Cripple Creek & Victor Gold Mining Company (CC&V) operates the largest surface gold mine operation in Colorado and is located west of Colorado Springs in Teller County between the towns of Cripple Creek and Victor. Gold was first discovered in the Cripple Creek mining district in the 1890s. CC&V has been conducting gold mining and precious metal extraction operations in the Cripple Creek Mining District since 1976. Current reserves are only amiable to surface mining since previous underground mining has depleted near surface ore rich veins.

Jan 1, 2014

By Walter Voglauer, Elisabeth Zechmeister

Five serial photos show the first second of the demolition of a 75 m high, reinforced concrete tower in the 23rd District of Vienna, Austria. The tower demolition with high explosives was necessary because a 175t excavator could not finalize the destruction with mechanical tools. All mechanical works in preparation of the blast, such as the borehole drilling, were done by civil companies under the responsibility of the contracted demolition company PRAJO. The blasting itself was planned and executed by the engineer corps of the Austrian Armed Forces, Sunday, May 26, 2013. Nearly 800 boreholes filled with more than 100 kg of military plastic explosives were initiated with about 1,600 Austin electric delay detonators in exactly 1,000 ms and 30 steps of delay. The 10,000 tons of reinforced concrete tower fell as planned without any damage to the environment. Photo 5. The rest of the detonators initiate the water pools filled with high explosives forming a bizarre white water front to fight the following strong development of dust. The first 1,000 milliseconds are over.

Jan 1, 2015

By John Manka

Emulsion explosives consist of an aqueous oxidizer phase, a fuel phase, and an emulsifier. The ability to use lower-cost sources for any of these raw materials presents an obvious economic advantage to emulsion manufacturers. This paper focuses on using low cost waste drain oils as the fuel phase in emulsion explosive applications. Laboratory studies showed that emulsions made from waste drain oils and agricultural ammonium nitrate prills were usable for emulsion explosives though their shear stability was weak. Customer field results proved that waste crankcase drain oil could replace half of the virgin diesel fuel in emulsion explosives to make an effective emulsion explosive product with a very low cost.

Jan 1, 2003

By H. S. Venkatesh R. Balachander, G. C. Naveen

During the construction of a 1020 MW underground hydroelectric project in Bhutan a huge rock fall took place in the Downstream Surge Chamber (DSC) during March 2016. The total quantity of rock in the fall area is estimated to be about 1,50,000m3 (2.6 billion cubic feet), out of which about 25,000m3 (0.44 billion cubic feet) of muck was removed. The removal of muck was stopped apprehending that the cavity formed due to the rock fall may get further aggravated leading to widening and destabilising the adjacent transformer hall cavern or it might day light as the top cover was about 190m (623 feet). As the fall has virtually blocked the 314m (1030 feet) long cavern and divided it into two different chambers (south and north), and that the muck cannot be disturbed, it was decided to erect concrete wall on either side of the fall up to the cavern roof and then later address the filling of the cavity with appropriate fill material. As the access to the DSC was there for the southern side it was decided to extend a cable tunnel which was terminated at a distance on the north side of the cavern by D&B so that once it gets punctured into the north wall of the DSC it can be used to access the fall from this front too. This is a unique situation where in every blast approaching the DSC, the parting between them is diminishing and hence the tunnel blast will be exerting axial load on the parting wall leading to dynamic transient loading conditions and buckling may take place on the northern wall of DSC. This paper describes the various drill blast combinations adopted for successful excavation of this tunnel.

Jan 1, 2019

Explosive manufacture, handling and transportation is hazardous and special precautions should be taken while manufacture, handling and transportation. Various regulations and rules defined in explosive act and factories act of India are discussed in this communication. General process control measures during the manufacturing of different types of explosives are also dealt in detail. Various processes hazardous in manufacture of various explosives like slurry explosives, PETN, detonators, styphnic acid, lead azide and lead styphnate and special precautions to be taken during the manufacture of the above explosives are also discussed.

Jan 1, 2007

By S. S. Jenkins Jr.

While the method is seldom used anymore, coyote blasting is an historically interesting way to blast large quantities of rock. It was used extensively in the days before modern fast drills were available and can be very effective in some formations that have a natural breakage pattern. This paper will cover the general principles, some blast design factors and point out several actual blasts including some very large ones.

Jan 1, 2005

By Y. Idrogo

Electronic delay detonators have been used in most types of blasting application with great success, with the accuracy and precision being used effectively to control negative environmental impacts like vibration. They have also provided consistent repeatable fragmentation and heave results. With the very wide choice in delay period and powerful timing design software, the choice of firing times to optimise blast results is not always clear to the designer. So the improved results achievable from the use of electronic delay detonators are often not optimally achieved.

Jan 1, 2018

By Ken Schei, Martin Reed, Samuel Bowser, John Wright

From October 18 through October 21, 2001, United States Antarctic Program blasters opened ten access holes for research divers in 11-ft. thick sea ice at Explorers Cove, McMurdo Sound, Antarctica. During this project, a blasting seismograph with a hydrophone accessory was used to monitor the underwater shock waves associated with the blasting technique. Shock wave values averaged 42.3 psi for initial (cratering) shots and 5.9 for subsequent clearing shots, indicating that the ice absorbs most of the shock wave. The results also provide data for refining safety protocols for divers and for the protection of marine biota.

Jan 1, 2003

By Elliott Giles

"Measuring a blast’s performance based on the bucket fill time or “diggability” has always been achallenge due to the subjectivity generally involved. The diggability of a blast is often based onopinions and speculation without the data to properly support the claim. This paper focuses howthe blast design can impact diggability and how it can be properly measured."

Jan 1, 2016

By Angel Rafael Fernandez, Yahya Khader Al-Harbi, Benjamin Cebrian Romo, Antonio Morato Medina

The kingdom of Saudi Arabia has set the goal to diversify their economy from oil into different fields including mining. As the vast Arabian Peninsula is explored, orebodies of Aluminium, Copper, Gold and Phosphates are found in high grades and tonnages. Hard rock is present in most of the projects and require high quality blasting in regard to ore dilution, wall control and fragmentation. Maaden Gold has currently 4 open pit mining operations 1 new opening and 2 underground. More projects are coming online in the next few months and years. A new generation of mining engineers need to apply drilling and blasting techniques that compete with modern and efficient open pit and underground mines.

Feb 6, 2023

By John W. Brown

"Adequate dust control in and around rock drills is a problem that must be solvedfor the health and safety of workers running the drill as well as those working around thedrilling operation This paper will discuss the designs available from most drill manufacturers todayand the effort ‘nvolved in keeping them effective on a productive basis."

Jan 1, 1999

By Rachel Bauer, Jacob Henderson, Dr. Catherine Johnson

Capital Quarries in Owensville, Missouri faces several challenges when designing a blast that allows for ease of movement while maintaining controlled throw and compliant air over pressure. The primary challenge is the nearest non-owned structure (NNOS) is a residential home located 250 feet from the quarry. Another challenge is a production bench which is 100 feet tall and separated from the NNOS by Pennsylvanian fire clay that filters out high frequency waves from the blast. Material from the blast must also be less than 5 inches in order to be processed by the crusher in the quarry. To provide as much relief as possible, production shots will consist of a single row with the minimum required burden. To design the shot, signature hole analysis was used to determine the optimal timing between powder columns. Electronic detonators provided an accurately timed shot to minimize the amplitude of the vibrations while maximizing the frequencies. Boretraking and 3D profiling with Renishaw laser profiler and Strayos drone photogrammetry provided an accurate burden measurement. Powder factor was kept at 1.3 tons/lb using bulk emulsion. The boreholes were split into 5 powder columns with the top of the hole firing first in order to blast to floor grade. The resulting shot produced good fragmentation and shot to floor grade. Seismograph readings showed air over pressure vibrations within legal limits. Due to this success, multiple shots will be designed using the process described.

Feb 6, 2023

By Dale Ramsey

As someone who has enjoyed photography as a hobby for many years, aerial photography to me has always been an exciting way to give a different perspective to my images. Our industry is always in search of new technology for bet­ter and more cost effective methods to improve our trade and aerial photography is a great tool to improve project planning or document its progress. It has typically involved conventional aircraft both fixed wing and helicopters but neither method is always available or cost effective. The lat­est innovation since digital imaging is the development of Unmanned Aerial Vehicles (UAVs) or drones. But there is a lot of uncertainty with this amazing new technology’s fu­ture in the U.S. as the Federal Aviation Administration (FAA) is under review and development of UAV regulations for commercial use which are slated to be completed in 2015.

Jan 1, 2015