Search Documents

By W. X. Yin

Electrowinning of lead from aqueous solution of PbCl2 and electrowinning of manganese dioxide from aqueous solution of MnCl2 are two research focuses in hydrometallurgy. This paper investigated a new process of simultaneous electrowinning of lead and manganese dioxide in chloride medium. The simultaneous electrowinning process in chloride solution not only can prevent chloride from liberating at anodes but also obtain two electrolysis products and decrease electric energy consumption. Diaphragm cell is used in the simultaneous electrowinning process to form separate anode and cathode compartment. The effects of temperature, HCl concentration in anolyte, NaCl concentration in catholyte and electrolysis time on current efficiency and cell voltage are studied. The results indicate that current efficiency of anode and cathode for 5 hours is 99% and 96% respectively, average cell voltage is 1. 701V, the weight ratio of lead and manganese dioxide produced at electrodes is 2. 39:1 under the optimum conditions. As anode products, manganese dioxide is ??MnO2, content of which in the products is more than 92%.

Jan 1, 2014

By Jacob Masliyah, Zhenghe Xu, Lujie Yan

"Understanding adsorption mechanism of polymeric organic process modifierssuch as carboxymethyl cellulose (CMC) on talc hasbeen a major challenge due to anisotropic nature of talc basal planes and edge surfaces. The main objective of this study is to investigate the adsorption of CMC on the basal planes and edge surfaces of talc.Smooth basal plane and edge surfaces of talc were prepared successfully by simple cleavage and sophisticated ultramicrotome cutting method, respectively. The prepared surfaces were characterized by atomic force microscope (AFM) imaging to be sufficiently smooth for colloidal probe force measurements using AFM. Anisotropic surface charge characteristics were determined,with the basal planes to carry a permanent negative surface charge and edge surfaces featuring a pH-dependent charge characteristic. The adsorption of CMC on talc basal plane and edge surfaces at pH 9 in KClaqueous solutions of various ionic strengths wasinvestigated by in situ AFM imaging technique. Themorphology of adsorbed CMC on talc basal planes and edge surfaces was found to be significantly different, due to different binding mechanisms involved. Interaction of CMC with the talc basal plane was found to bedominated by hydrophobic interactions while its binding with the talc edge surface was mainly through chemical complexation and hydrogen bond. The amount of CMC adsorbed on both talc basal planes and edge surfaces increased with increasing ionic strengthof solutions. The methodology developed in our study opens the door to probe polymer adsorption on anisotropic phyllosilicate surfaces, which can help us better understand the mechanism of polymer adsorption on specific mineral faces."

Jan 1, 2014

The value creation with kaolin clays depends on removing the colored impurities which manifests in to higher brightnessone of the most sought after properties on applications such as paper coating, paint and others. The processes for removing impurities include magnetic separation, froth flotation and selective flocculation. While the flotation and selective flocculation processes exploit the physico-chemical differences between the surface properties, the magnetic separation uses the bulk magnetic susceptibility differences between the diamagnetic clay and ferro- and para-magnetic nature of the impurities. The major advantage with magnetic separation remains high yield and no or low reagent usage. However, the magnetic separation technology suffers from low separation efficacy when finer colored impurities (<1 µm) are encountered in the feed. Use of stronger magnetic intensities during magnetic separation showed limited success; nonetheless the adverse effect due to finer size range remains a dominant effect even at 5 Tesla magnetic field. Furthermore, the presence of diamagnetic colored impurities irrespective of their sizes can not be removed. Cytec Industries has recently developed a ?bolt-on? chemical enhancement technology for magnetic separation that essentially embraces the best product performance attributes of flotation and selective flocculation while keeping the chemical usage to a minimum level and using the readily available magnetic separation equipment. The paper will outline the technology and illustrate optimization work at pilot plant magnet on a wide variety of crude accommodating the process needs and plant limitations. The major advantages of chemical enhancement technology to magnetic separation include: 1) simple extension to existing magnetic separation technology, 2) ability to produce comparable product in quality with cost effectiveness compared to flotation and selective flocculation, 3) removal of impurity minerals over wide size range, 4) removing non-magnetic impurities, 5) providing robust process with high process yield and 6) operation-friendly nature. Furthermore, chemical enhancement technology for magnetic separation has also emerged as a platform for re-moving impurities at low levels in other mineral systems as well.

Jan 1, 2014

By Z. B. Pan

The innovative point of this new technology can be described that under normal pressure and 70°C, using a new combined activating and oxidizing agent, the minerals bearing arsenic and organic carbon are oxidized effectively. This technology can be applied in commercial scale. The high carbon and arsenic bearing gold ore is taken from Gansu, where hundreds of tons gold deposit. The ore has 0.51% of arsenic and 1.75% of carbon (1.07% of organic carbon). The gold occurs mainly in native with particle size 0.02~0.6 mm and a few are enwrapped by pyrite and arsenopyrite. The traditional cyanide leaching process gains a very low gold leaching rate with only 5%. Through systemic experimental study, the technological flowsheet of flotation process for concentrating gold, then pre-treating the gold concentrate followed by cyanide leaching the gold concentrate are used. With 4.92 g/t gold of head sample, the gold concentrate with 46.52g/t gold grade and 96.53% gold recovery is gained by flotation process. Followed by pre-treatment for 6 hours, the gold concentrate is leached with cyanide after filtration and washing. The total gold leaching rate is up to 95.44%.

Jan 1, 2014

By M. Zolghadri

MIBC and sodium metasilicate are used as a frother and a dispersant in coal flotation respectively. In order to study interaction between them, flotation experiments were performed on fine coal (<150 microns). It was found that if the frother (MIBC) dosage is in excess of a certain limit, it has an activation effect on the gangue minerals associated with coal. In addition, it was found that however sodium metasilicate can disperse clay slimes eliminating slime coating, but in the case of excess dosage, could intensify activation effect of MIBC, which is undesirable in coal flotation. Keywords: coal flotation, sodium silicate, frother, dispersion, activation

Sep 1, 2012

By Y. X. Li

In order to control the pulp level in flotation column which has long time-delay and great inertia, and is difficult to establish an accurate mathematical model, a Fuzzy-PID dual mode controller is applied. This method takes advantage of both strong flexibility and good reliability of fuzzy logic and high precision of PID. With the very stable and reliable process instruments, the control system has a good control performance and results the stable control of flotation column.

Jan 1, 2014

By X. G. Liu

Bentonite is an excellent sealant mineral material because of its desirable swelling and self-healing characteristics, low permeability, sorptive qualities, and longevity in nature. A new type of water-swelling building sealant made from bentonite was studied in this paper. The building sealant is prepared by Na-base bentonite, vaseline and paraffin wax under different mass fraction of bentonite (which is 60%,65%,70% respectively). Under unrestricted state, some properties of samples were investigated. The volume expansion ratio at 24 h is 211%, 222%, 256% , and permeability coefficient is 2.86×10-8 cm/s, 4.15×10-8 cm/s and 4.78×10-8 cm/s respectively; low temperature flexibility of the sample (bentonite quality is 65%, 70% respectively) is good, and it does not flow heated for 2 h under 80?. The results of XRD and SEM indicate that bentonite is coated preferably by vaseline, and the spacing of layers of bentonite do not changed. The sample can keep full water swelling ability, and has good molding process. The test results prove that the properties of samples may reach the standard of building sealant.

Jan 1, 2014

Optimising flotation designs and innovations is a complex process involving many parameters, one of which is ensuring sufficient testwork is carried out at plant level before these innovations are launched in the marketplace. This paper will describe how modern design tools are utilized, what are testwork phases at various plants and how results and observations have helped to validate and optimise flotation design innovations. Scale-up of equipment has long been the prevalent trend, but how long can it continue? Are there other means for pushing the boundaries of present technology? Some present challenges and future directions are given in the light of theoretical criteria for scale-up and how it has been applied in practice. Very large flotation cells of 300 m3 size have been installed in New Zealand, and relevant results from the metallurgical and mechanical aspects are presented and discussed. Utilization of the cell volume is also important. New innovations in the hydrodynamic domain are presented and discussed. Means to enhance flotation of coarse and fine particles are shown with results from plant testwork. Accurate control of large flotation cells is vital to optimize yields and grades. Froth image analysis and intelligent level control are presented ? again - with relevant plant results.

Jan 1, 2014

By X. Y. Zeng

Most Chinese titanium bearing minerals are the composition of magnetite vanadium and ilmenite. All of such mineral processing plants use low intensity magnetic separators to recover magnetite and vanadium goes with magnetite. In the past years most of the plant tails containing about 10% TiO2 were abandoned. Now many of these plants use SLon magnetic separators to recover ilmenite in the roughing stage, which can throw away most of the gangs and slimes with very low cost. The new development of applications of SLon magnetic separators in Chinese ilmenite processing industry is introduced in the paper.

Jan 1, 2014

By G. Kumar

Water for domestic consumption is an essential right of society, which must be over secured. Water reclamation and reuse provides a unique and viable opportunity to augment traditional water supplies. As a multi-discipline and important element of water resource development and management, water reuse can help to close the loop between water supply and wastewater disposal. Effective water reuse requires integration of water and reclaimed water supply functions. During the coal mining activities, large quantities of water get contaminated and loses its potability characteristics. On an average, in coal mine operation, each coal mine discharges effluents at a rate of nearly 0.5 MGD and thereby wastage of nearly 50 MGD of water takes place per day from the famous Jharia Coal Field of the Dhanbad District. In this paper, attempt has been made to control the extremely high turbidity of mine waste water by using different coagulants and it is observed that ferrous sulphate is the most effective coagulants followed by alum, ferric sulphate and lime. Also combinations of coagulants are used for getting the optimal results. Further steps were also discussed to make this water potable and a scheme of low cost water supply system of mine waste water has been suggested under the Water Management Strategies. Keywords: potability, turbidity, coagulants, water management strategies

Sep 1, 2012

By J. Temuujin

Mongolia has some of the world?s largest coal reserves with an estimated total coal reserve of over 150 billion tonnes. At present, over 90% of Mongolian electricity is produced by combined heat and thermal power stations. The main coal deposits used for Central power system&apos;s power stations are Baganuur, Shivee-ovoo lignite type coal and Shariin gol bituminous coal. In Mongolia almost 600,000 tonnes of coal combustion by-products are disposed of in waste ponds. In this research, we have thoroughly characterized Mongolian coal combustion by-products including fly ashes sourced directly from thermal power stations and ash retrieved from ponds. It was determined that fly ashes generated from Baganuur and Shivee-ovoo coal deposits are class C, while ash from Shariin gol coal is class F (according the ASTM C618). All ash products were characterized by chemical, mineralogical, granulometrical, porosity, FE-SEM and radiation methods. Fly ashes sourced directly from power stations were found to be more suitable for manufacture of geopolymers for building materials application and zeolite synthesis than ashes retrieved from ash ponds. The adsorption and porous properties of zeolitic compounds were measured and found to be suitable for adsorption of Cr6+ from simulated tannery waste water. Keywords: coal, coal combustion by products, synthesis, geopolymers, zeolitic compound

Sep 1, 2012

By Per Svedensten

One of the most significant behaviour of a crushing plant is the constant variation in the process. The variation is caused by two major effects. The first and constantly changing is the rock material properties. During operation rock material with different strength and particle size distribution is fed to the plant which makes the performance of the equipment to vary. The second and more slowly changing variation is caused by wear on the processing equipment. These effects must be predicted in order to be able to optimise a crushing plant. This paper demonstrates how Monte Carlo simulation can be utilised to study and operate crush-ing plants. By introducing Monte Carlo simulation the varying process can be study and also optimised. To maintain the optimised process performance supervision is needed. This paper demonstrates how results from the Monte Carlo simulation can be utilised for process supervision. Charts for process measurements can for example be derived. These can then be used to guide decision making and understand how the variation and performance of the plant changes over time.

Jan 1, 2014

By M. F. He

The depression of pyrite in marmatite flotation by a new depressant Sodium Glycerine-xanthate (SGX) has been investigated through microflotation, zeta potential, and adsorption measurements in systems open to the atmosphere. The flotation tests of single mineral show that in the presence of SGX, marmatite can be activated by Cu2+ and shows good flotability, while pyrite can?t be activated and therefore shows poor flotability, as a result these two minerals can be separated using butyl xanthate as the collector. The depression mechanism of SGX on sulfide minerals is discussed based on Zeta potential and adsorption isotherm. Zeta potential experiments demonstrate that at the presence of Cu2+, SGX can strongly adsorb on the surface of pyrite, while it can?t adsorb on the surface of marmatite, thus the results are in accordance with those of flotation experiments; the results of adsorption isotherms show that the adsorption density of SGX on pyrite is greater.

Jan 1, 2014

By Pejman Oghazi

During the last decade the output of mining companies has increased rapidly. The key driver is the increase in demand for raw materials in the developing world, and thus this demand has driven up ore prices. From the time when the Raw material group (year 2000) started to introduced their index, it was set to 100 points. Today, year 2011, the index is over 400, which means that ore prices have quadrupled since then. Mine companies have to go deeper in the mines to access the ore bodies to increase the mine capacity and to be able to respond to the market. By going deeper in the mine, there will be new challenges that have to be considered. One of these challenges is how to handle the mine water that is produced in the mine. The water has to be moved to the surface in order to keep the mine from flooding, and this causes more challenges. One solution is to pump the mine water up to the surface without treatment; however, this causes considerable pump wear and the water will still require treatment on the mine?s surface. Another solution is to treat this water in the mine before pumping it to the surface. Metso Minerals has a system solution to treat the mine water, by separating the solids from the mine water. This system reduces the erosion in the pumps and will save many maintenance hours in the long term. One other option is to use the treated water in a closed circuit and reuse it in the process. This system can be divided into three steps: Firstly, a spiral dewaterer to remove the coarse solid particles. For the next step, lamella thickener is used to remove most of the solids, and lastly tube press to handle the sludge from the underflow lamella thickeners. Keywords: mine water, mineral processing, dewatering, separating

Sep 1, 2012

By U. S. Chattopadhyay

The estimated requirement of the nation by the year 2020 is approx. 80 Mt of steel and more than 0.2 million MW installed capacity of the electricity, thereby increasing the consumption of the coking and non-coking coal, which is expected to be in tune of about 75 Mt & 500 Mt respectively. One of the major deleterious factors in achieving the goal is the deteriorating quality of the feed coal used in both steel and power industries. Indian coking coals, in general, are typified by high ash, high inert (both organic and inorganic), low rank, low reactive macerals content, heterogeneous petrographic make-up, inferior coking properties and poor amenability to washing, thereby necessitating suitable washing measure. Coke-based steel industries in India require washed coking coal containing ash % varying between 17-19. The situation demands taking on immediate challenges to fill up the gap between the requirements and supply of coking coal. This paper reviews the R&D attempts in this laboratory and throws light on the key measures as long-term solution to the problem. Search for alternative source of coking coal, like LVC coal and their judicious preparation technology. The low volatile coking coal (LVCC) constitutes about 50% of the total coking coal reserves in India. These coals are characterized by high raw coal ash content (37 to 40%) and very difficult washability potential. If these coals are treated in the existing washeries, which are generally 2 or 3-product systems, the cost of clean coal is high as the byproduct sale value is low. It has been proposed to produce a new type of by product, which enjoys high demand and good coking properties.

Sep 1, 2012

By Sharma K. K.

India is the third largest producer with accounting to fifth largest reserves base of coal in the world. Indian coal has high ash content (15-45%) and low calorific value. The basic processes being used in India at different places for coal washing adopts old techniques. Much of the valuable part is being lost during washing processes. With enhancement of the available techniques and use of new processes like flotation process indicates better recovery of carbon values during washing stage. The same will increase the reserve base, improve economy of operation and alleviate environment related problems. In the above backdrop this paper portrays the case study of an existing coal processing plant in India. The case study includes the modifications being incorporated in the existing process to enhance the product value. The existing practices and the future trend of process technology that could be adopted to meet the requirements in this country are also discussed. Keywords: washing, dense media cyclone, magnetite media, flotation

Sep 1, 2012

By V. K. Chandaliya

N-Methyl-2-pyrollidone (NMP) has already been proven a good solvent for extraction of coal. It is believed that organic components of coal are likely to be dissolved with the solvolytic power of NMP. During dissolution process, original coal also gets disintegrated and thus helps in further extraction. Coal extraction highly depends on temperature, coal to solvent ratio, N-Methyl-2-pyrollidone (NMP) to Ethylenediamine (EDA) ratio and the size of coal particles. The process has been established in the laboratory. There is no reference available beyond lab scale. In present study, we are running a bench scale plant with 40 kg/batch capacity. Design of experiment was done in such a way that the optimum zone of the process gets evaluated for clean coal having low ash with high yield. Bench scale plant trial was conducted based on optimum zone developed during design of experiments (DOE). From the DOE analysis it was observed that feed size and coal to solvent ratio are important parameters for this process. Total 27 experiments (four factors with 3 level of variation) were designed through Box-Behnken model. It was observed that -0.5 mm feed size of coal, 150 °C extraction temperature, 17:1 NMP to EDA ratio, 1:9 coal to solvent ratio was optimum conditions. The results obtained at optimum conditions are 50% clean coal yield with 5% ash.

Sep 1, 2012

By P. A. Bepswa

A numerical study done to test the efficacy of heuristics developed for the design of measurement networks for high precision metallurgical accounting is presented in this paper. The heuristics considered were designed to maximise variance reduction of terminal stream measurements through data reconciliation for observable linear flow systems. A complex metallurgical process flow sheet from the mineral sands industry was used as a case study. Monte Carlo type simulations coupled with a non-linear programming based steady state data reconciliation algorithm were used as tools to investigate the heuristics. The results obtained suggested a close correlation between magnitudes of measured variances and the respective levels of variance reduction obtained through data reconciliation for both internal and terminal streams. It was observed that variance reduction through data reconciliation was maximised for terminal stream measurements in networks characterised by high precision measurement of internal streams and/or in flow sheets characterised by high ?stream to node ratios?. Terminal streams attached to highly interconnected parent nodes were observed to experience higher reductions in variance compared to terminal streams attached to less interconnected parent nodes. The results generally highlight the additional benefits of highly interconnected flow sheets and high precision internal stream measurement regimes on the maximisation of variance reduction of terminal stream measurements through data reconciliation. These findings are significant to metallurgical accounting and to process accounting applications in general in that they provide a conceptual basis for design decision making regarding the construction of measurement networks aimed at maximising variance reduction of targeted streams through data reconciliation.

Jan 1, 2014

By Zhu Yangge, Zheng Guibing, Hu Xiaoxing

"Because of the similar crystal structure and surface properties, it is very difficult to realize the efficient separation of magnesite and dolomite by flotation, which is the main reason restricting the utilization of magnesite resources with dolomite symbiotic. To deal with a magnesite resources with high content of calcium impurity in northwest China, a novel decalcification technology by combining flotation with leaching is proposed in this paper. In flotation process, a novel flotation collector with good efficiency and low temperature resistance was developed, and the depression effect of sodium hexametaphosphate was investigated. In leaching process, the leaching rate difference of calcium and magnesium was observed. By industrial test, from the magnesite ore with MgO content of 43.96%,the grade and recovery of obtained concentrate ( calculated by MgO) are 47.28% and 67.68% respectively, at the same time, CaO content decreases from 3.91% to 0.30%, which means that more than 95% of CaO impurity is removed.INTRODUCTIONMagnesite is one of the main raw materials for the production of refractory materials, and it is widely used in metallurgy, chemicals, ceramic, construction and other industries. China is the most important supplier of highquality magnesite resources, accounting for about 60-70% of the world's identified supply of magnesite products is provide by China (Jewell, 2014). In recent years, high-quality magnesite ores can be directly used are going to run out in China, and the utilization of magnesite resources with high impurity content have drawn more attention.The main purpose of purification for magnesite is to remove SiO2 and CaO impurities which affects the strength of the refractory material. Flotation is the commonly used method to remove impurities in magnesite ore. Reverse flotation with cationic collector is usually adopted to remove silicon containing impurities, and a great deal of literature has been reported (Santana A. N. and Peres A. E. C., 2001; Wang and Sun, 2008; Zhu et al, 2014; Wu et al, 2015; Ivan B. et al, 2017). But when the major gangue component is dolomite, it is very difficult to realize the efficient separation due to the similar crystal structure and surface properties between magnesite and dolomite. To solve this problem, researches have studied the surface properties of magnesite and dolomite, such as wettability, electrical property, solubility and solution chemistry (Nermin and Nurgul, 2006; Nermin 2006; Ozbek and Abali, 1999; Lacin et al, 2005; Bayrak et al, 2006; Bakan et al, 2006; Chen G. and Tao D., 2004), but the commonly studied direct flotation using oleic acid as collector is still hard to receive an ideal effect."

Jan 1, 2018

By Arun Appadurai

Pneumatic transport systems play a vital role in conveying discrete particles over a sizable distance with minimal energy consumption. However if such a system is not designed keeping particle physics in mind, it leads to intractable problems which could possibly assume dangerous proportions, including but not limited to expensive redesign of the entire system. This paper describes a novel method, which harnesses the powerful technique of Computational Fluid Dynamics (CFD) to investigate a problem occurring in rotary kilns using coal as a major fuel source. In some of the sites, a unique phenomenon of abnormally high CO emission was observed and owing to the highly random nature of occurrence, it was difficult to scientifically investigate the problem and its cause. Most of the published solutions for the high CO problem tend to concentrate on the incomplete combustion aspect of the kiln and resolve the situation by increasing the air supply thereby improving the stoichiometric ratio of combustion. This paper offers an alternate correlation that relates high CO emissions to the phenomenon of coal delivery fluctuations caused by the sub-standard operation of the coal transport system. A CFD model for the coal delivery pipe is validated by utilizing the actual process data sourced from the measurements taken from a functioning plant. The results of the model are used to derive correlative conditions that point to the unstable operating conditions of the coal delivery pipe prevalent in the industry. The conclusions are summarized into a series of recommendations for optimized design of coal delivery systems which are implemented in a pilot plant. The results irrevocably prove a statistically significant reduction in CO emissions without resorting to increased air supply and power consumption. Keywords:CFD, Pneumatic Conveying, Saltation Velocity, Particle Flow

Sep 1, 2012