Search Documents

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

By Robert B. Parsons

"In all likelihood, Canada's mining industry would be adversely affected by corporate tax reform proposals actively being considered by the Department of Finance in Ottawa. When the next set of proposals for lax reform is released later this year as promised by Finance, the mining industry had better be prepared 10 take a hard look.IntroductionTwo federal budgets ago, in May 1985, Finance Minister Wilson tabled budget papers that were more massive in terms of volume than most federal budgets. Buried in this mass of documentation is a discussion paper entitled ""The Corporate Income Tax System-A Direction For Change"". When the discussion paper was tabled over one year ago, reaction from the business sector was almost nonexistent. By and large, the paper was regarded as nothing more than one more federal publication of mild academic interest.But, recent events suggest that this discussion paper for corporate tax reform could be the cornerstone for a series of changes to the tax laws which would have more profound and widespread effects for all sectors of the economy than any reform since 1971 . No industry in Canada can afford to ignore the movement afoot in Ottawa for corporate tax reform."

Jan 1, 1986

By G. M. Ritcey, V. M. McNamara

"In the processing of gold ores by the cyanidation route, effluents which are discharged to the tailings areas can contain up to several hundred parts per million of cyanide in complex combination with similar quantities of heavy metals. Complicating this obvious problem of waste control are concentrations of thiosalts and thiocyanates which are roughly equivalent to the amounts of cyanide species. Although most gold mills are located in thinly populated areas, such contaminants can represent a potential environmental problem due to the various limitations exhibited by on-property ponding.The former Extraction Metallurgy Division of CANMET recognized the problem and, in early 1974, invited representatives of the gold mills to Ottawa to discuss the situation. At that meeting members of the Division presented a ""state of the art"" literature survey of cyanide abatement technology for waste solutions, together with preliminary cost estimate data(1). Shortly thereafter, Environment Canada, together with Environment Ontario, decided upon a guideline of 0.1 ppm (0.1 mg/l) total cyanide content as tolerable for an effluent stream which is discharged, in any manner, to the watershed."

Jan 1, 1978

By P. M. Solozhenkin, O. I. Ibragimova, I. P. Solozhenkin

Molecular models of complexes of poorly studied bismuth, gold, and arsenic mineral clusters and reagents were created for use in collector activity forecasting using Chem Bio 3D and ChemOffice2005, with optimization by MM2. The density functional theory approach was used to determine HOMO, LUMO, SOMO, and total energies, atomic charges, and s, p, d- populations for various compounds. The structure-based virtual screening (SBVS) and docking technique was proposed to reduce the vast number of compounds to a more manageable number for selection of potential flotation candidates. The prognosis of collector activity evaluation (PCAE) strategy was proposed as a consistent approach to estimate the interaction between a collector and a mineral cluster as the difference between the total energy and sum of cluster energy and collector energy to search the analogue of butyl xanthate. The negative relationship between PCAE and flotability was shown. The combinations of dialkylamino sulfhydryl collectors can be considered as prospective reagents for gold-bearing sulfide ore flotation. These results were confirmed by experimental data in ore flotation. The increase in recovery of gold and bismuth with the aid of a combination of reagents has been established and additional cyanidation of tailings has been avoided.

Jan 1, 2016

By Donka H. Andreeva

Gold catalysts based on different supports, titania, zirconia, ceria and mesoporous titania and zirconia, nonpromoted and promoted by vanadia in the reaction of complete benzene oxidation have been studied. XRD, HRTEM, TPR, Raman and ESR spectroscopy were applied for the characterization of the catalysts. The influence of gold on the reduction behavior, state and structure of vanadia on the surface was studied, as well as the role of supports nature on the properties and catalytic activity. A strong synergistic effect between gold and vanadia was observed for the all studied catalysts with an exception of the catalysts supported on mesoporous zirconia. In the last case the catalysts containing gold and gold-vanadia exhibit high and equal catalytic activity. The catalysts on ceria show highest and stable catalytic activity in the studied reaction among the all studied catalysts.

Oct 1, 2003

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By Greg Gosson

"Early efforts to develop formal reporting systems to quantify and classify mineral deposits date back over 100 years. (e.g. Hoover 1909: “Proved, Probable, Prospective Ore”). This was at first driven by mine operators’ need for reliable estimates of what their mines could produce. Disruption of transportation routes by world wars prompted western governments to recognize the need for assessments of strategic sources of metals and minerals that could support domestic industry during times of crisis. Categories were created to quantify mineral potential which were additional to those of mine reserves. Terms such as hypothetical and undiscovered resources entered the lexicon. Capital markets serving the mining industry were traumatized during the latter part of the 20th century by undisciplined and fraudulent disclosure by exploration companies of mineral deposit potential. Government securities regulators pressed for the development of credible reporting codes (e.g. SEC Industry Guide 7: 1981; JORC 1989; SAMREC 1994, CIM 2000). Representative organizations from the major western mining countries generally agreed that there should only be three categories of mineral resources (measured, indicated, and inferred) and two categories of mineral reserves (proven and probable). This was formalized in 1997 with the “Denver Accord”. Acceptance of the standard terminology may have been the easy part, because the challenge for the 21st century is to get general industry acceptance and agreement of the principles behind the definitions of each category. There has been noticeable movement towards this objective in the last few years. This is reflected in part in the updated reporting codes by JORC 2004, CIM 2005; SAMREC 2007; SME 2007; and PERC 2008, and the development of the CRIRSCO International Reporting Template 2007."

Jan 1, 2003

By K. Buxmann

Climate change is a subject of growing concern. Based on the International Energy Agency, about 19% of man made greenhouse gas emissions globally are generated by the transport sector. This paper will focus on the environmental aspects of the light-weighting in transport and the resulting savings of fuel and electricity. Aluminium is an option for lightweight applications in transport, with very high benefits not only in the use stage, but also in the stage of vehicle recycling. Life cycle assessment is used to quantify the relative benefits of light-weighting specific components of cars, commercial road vehicles, buses, ships and trains. A vehicle consists of many components, which are produced by different processes and undergo different types of end-of-life operations. This document does not intend to compare a generic aluminium vehicle with a generic "heavy materials" vehicle. It rather tries to use a pragmatic approach based on specific examples of components where aluminium is used and can be used in the design of new vehicles, also taking into account future developments. The case studies in this paper are based on real cases where aluminium was used. For each component, sensitivity analyses are applied to see the impact of specific parameters such as the end-of-life recycling rate and the use stage driving distance. Significant greenhouse gas savings by the use of aluminium are demonstrated for cars and even higher ones for trucks, buses, trains and ships. In addition, the total potential benefits of light-weighting with aluminium are shown on the global level.

Jan 1, 2007

By D. B. Hyma

"The Raglan Ni/Cu property is located on the Ungava Peninsula in Northern Quebec, Canada, at a latitude of61°42' and a longitude of73°40', approximately 40 km southwest of Douglas Harbor. Geological reserves are estimated at 18 million tonnes, grading 3. 1 % nickel, 0.9% copper and smaller amounts of cobalt and platinum group metals.Extensive project development has defined the concentration process, concentrator sizing, tailings and environmental management required for this project.The grinding circuit selected is a fully autogenous primary grind, with pebble crushing and a pebble mill for secondary grinding to produce a product of 80% -70 microns for flotation.The flotation circuit is a simple circuit utilizing roughing, a regrind of rougher concentrate to 80% -20 microns, two stages of column cleaning with a cleaner scavenger bank on the column tails.Concentrate handling options were thoroughly reviewed because of the pyrophoric nature of the concentrate, remote site location and long distance to downstream processing. The preferred option, currently.is to dry the concentrate at Raglan to less than l % moisture and then pneumatically handle the powder.A detailed analysis of tailings placement options, suggests filtered tailings placement to be the preferable route for the Raglan site.INTRODUCTIONThe Raglan Project, as proposed by Falconbridge Limited, will develop extensive nickel-copper deposits in the Ungava Peninsula, Quebec, Canada. The project schedule and construction conditions in the project area are demanding. The Raglan mineral deposits have been the subject of numerous studies and evaluations over the last thirty years and the Phase I 1991 pre-feasibility document includes exploration information obtained in the 1989 and 1990 drilling seasons. This review concluded that an 800,000 tonnes of ore per year mining and concentrating complex located at Katinniq could produce 20,000 tonnes per year of nickel at competitive costs."

Jan 1, 1993

By P. B. Demarsh

"Location: - On highway 59, 17 miles east of Val d 10r near junction of Montreal highway in Northwestern Quebec.Life; - Started production 1952, ceased 1965.Ore: - Pyrite, chalcopyrite and small amounts of free gold and goldsilver tellurides in narrow quartz-carbonate-tourmaline veins in granodiorite. Specific gravity 2, 70.Capacity: - 700 tons daily Bevcon ore supply, l 000 tons daily when custom ore available.Assay: - Heads 0 .140 oz. per ton; tails 0. 009 per ton; extraction 92.5%.Grind: - 75% minus 200 mesh at 700 tons; 68% minus 200 mesh at 1000 tons. Detention time 28 hours and 21 hours respectively.Treatment: - Cyanidation process.Reagents: - Per ton. Aero Cyanide (NaCn) 0, 50; crushed unslaked lime 1. 75; zinc 0. 03; litharge 0. 10; steel consumption 2. 25.Water: - Pumped from land-lock spring fed lake l 1/2 miles distant.Cost: - Per ton. Crushing 0. 13; grinding 0 .32; filtration 0. 07; cyanidation 0.14; miscellaneous 0.29; total 0.95.Power: - Hydro-electric, 25 cycle, 12, 000 volts reduced to 550 volts.Labour: - Predominantly French Canadian, nucleus English Canadians.Tailings: - Impounded low lying pond.Personnel: - 15 including supervision.Flow sheet: - Canadian Mining Manual l 9 5 6 .Building: - Wood truss construction: 3/ 4 in. siding, ten test and 1/ 4 in. transite outside. Corrugated galvanized iron roof. Ground level foundations. Internal self induced heating. Wood stave tank equipment."

Jan 1, 1966

By A. N. May

"This paper describes the present approach of the Mines Branch to the problem of measuring the stress condition in the interior of rocks surrounding underground openings. An instrument, which will be referred to as a stressmeter, has been developed at the Mines Branch to measure un-directional stress changes in absolute units. There are two modes of operation of this stressmeter. It can be regarded as a fixed instrument, in which case it is installed at the end of a diamond drill hole and left in position to record any subsequent stress changes taking place. Alternatively, three of the stressmeters can be used in conjunction with a trepanning opera-tion to allow the existing stress condition to be determined. The initial laboratory work and subsequent experiences in the field with the stressmeter are described. All the field development work on the stressmeter was made possible through the co-operation of Canadian Refractories Limited, Kilmar, Quebec."

Jan 1, 1960

By H. Nakano

The codeposition behavior of impurities such as Ag, Bi, Fe, Ni, Pb and Sb with Cu was investigated galvanostatically at 5-3000 A/m2 using a Pt cathode at 60 °C in acidic copper (I) chloride (cuprous chloride) solution at pH1-2 containing 1.0 mol/L of Cu+ and 4.9 mol/L of Cl-. The impurities were classified into two groups: Group I (Ag, Bi) which codeposits with Cu as a metal, and Group II (Fe, Ni, Pb, Sb) which is slightly involved in the deposited Cu in nonmetal form from the electrolyte. Silver and Bi in Group I behaved as more noble metals than Cu, and significantly codeposited with Cu, showing typical features of regular-type codeposition. When Cu was deposited dendritically, the Ag and Bi content in the deposit increased with increased duration of electrolysis as a result of decreased net current density caused by increased cathode area. The current efficiency for Cu deposition in impurity-free solution was 95-100% over 100-1000 A/m2, but it abruptly decreased at above 1000 A/m2 when the limiting current density of Cu was attained. Although Fe, Ni, Pb and Sb in Group II were involved to 0.01-0.02 mass% in the deposit, they had no influence on the current efficiency or morphology of Cu.

Jan 1, 2007

By Mehmet Guney

This article is based on a detailed heat investigation conducted at the Rokana Division of Nchanga Consolidated Copper Mines Limited while both authors were employed in Zambia. Mindola Mine is one of the three underground mines comprising the Rokana Division on the Copperbelt of Zambia, producing about 270,000 tons of ore per month at 1.9% Cu and 0.14% Co. The total volume of air being circulated by means of five primary fan installations slightly exceeds 1,000 m3/sec at standard density. Sectional bulk cooling is practised where air cooling coils are installed at primary splits some considerable distance from the stoping operations. Total capacity of the refrigeration complex is 10,500 kw (3,500 R. tons), of which about 7,000 kw is available as effective cooling power after losses, but the heat removed from the coifs is about 3,500 kw with 61% over-all plant performance. An extension program is planned for a further five production levels with the re-deepening of a sub-vertical shaft. Thermal heat will become a major problem at increased depth associated with higher rock temperature, higher thermal conductivity of the rock groups encountered and fissure water flowing into working areas through the strata with increased rock temperature. This paper describes the ventilation and refrigeration practices in Mindola Mine, with special reference to future thermal heat problems. These are discussed with a view to mining at depth.

Jan 1, 1979

By H. Abdollahi

Cold rolling is one of the most important techniques in metal forming since the cold rolling products are almost finished product, The product quality of this process is widely influenced by friction in the roll gap; therefore, controlling the friction and other parameters affecting the cold rolling is very important in order to have a product with high quality, Among the cold rolling parameters, the pressure distribution or friction hill within the roll gap is known as the most significant one, In this study, a new software (Matroll), is introduced which can determine the coefficient of friction (COF) and plot the friction hills for an industrial mill, Besides, based on rolling equations, it offers about 25 rolling parameters as outputs. To verify the software operation, the real industrial rolling data was used as inputs, The results (outputs) are in good agreements with the findings of other researchers, The COF values are very reasonable, The friction hill shows that COF is not constant over the whole arc of contact.

Jan 1, 2005

By Z. Abbasloo, A. Masoomi, L. Ebrahimi, A. Mortazavi, A. Keshavarz

"Investigation and 3D analysis of Heap no. 2 of Meydook copper complex was the subject of this study. In this project all geological and geotechnical investigations conducted in the mine were evaluated aiming at determination of Heap no. 2 design parameters. The main objective of the project was to evaluate the potential for construction of Heap. No. 2 on a waste dump built in a valley in the north side of the pit.Considering the space limitation for dump location this was a viable alternative to reduce the costs associated with heap no. 2 construction. Moreover, it allowed for a significant reduction in overall mining costs. Considering the project condition, a 3D analysis of heap major structures including; valley rock foundation, waste dump, and low grade ore was carried out. Five sets of analyses were conducted and the displacement and stress fields were calculated within the heap no. 2 components. In all analyses conducted the subsident profile was determined for the valley base rock and heap foundation (waste dump). Moreover, the shear interaction between heap and waste dump was evaluated at the heap interface. The analyses results showed that the maximum settlement at the heap base is about 4-5 cm and the waste dump provides a safe and reliable base for heap construction. Moreover, the analysis results showed that the selected %5 grade for the heap interface is good and does not pose any risk in terms of heap Interface shear displacements. A sensitivity analysis of heap mechanical parameters was also conducted. The obtained results show that if the friction angle of heap material is reduced below 25 degree due to acid spraying process, the heap walls become unstable and the heap geometry must be redesigned."

Jan 1, 2015

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"Abstract - The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3 and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By H. J. McQueen

The irregular history of Mg wrought products is briefly described. The temperature and strain rate dependence of microstructural evolution, flow stress and ductility of Mg alloys in hot working, are described. The flow curves rose rapidly to a peak stress which was lower as temperature T rose and strain rate e declined and above 300°C the curves extended into plateaus until failure. Clearly grains not oriented for slip undergo mechanical twinning in the initial stages (a 0.15) at all temperatures. Basal slip proceeds in suitable grains and in the twins. The stress concentrations at grain and twin boundaries lead to slip on non-basal systems and to the formation of subgrains with greater dynamic recovery (DRV) at higher T or lower e. With increasing strain, misorientation builds up resulting in dynamic recrystallization (DRX) first at twin intersections and later at grain boundaries which have become quite serrated. Even after extensive straining at high temperatures, the new grains are found mainly along the boundaries of the original grains, leaving their centers with only basal slip except when nucleation at twins leads to completion of DRX throughout a grain. Despite similar shear modulus and melting point to Al, hot mechanical forming behavior of Mg alloys differ due to differences in crystal slip systems, twinning, and second phases. Moreover, the influences on forming of alloy additions (solutes, segregation in casting, dispersoids, precipitation) and impurities are not as well catalogued as for Al. Despite the benefits from dynamic recrystallization, varied grain orientation effects, heterogeneous substructures and the resulting stress concentrations result in considerably lower ductility for Mg alloys at the same stress level as for Al materials. Application of these theories to extrusion, rolling and forging and the effects on product properties are surveyed.

Jan 1, 2006

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By J. E. Dutrizac

Mercury balances have been obtained for the flotation circuits at Pamour Porcupine Mines, Timmins, Ontario, and at Brunswick Mining and Smelting Corporation, Bathurst, New Brunswick. The mineral form of mercury in both deposits has been ascertained. At Pamour Porcupine, the mercury is approximately evenly divided among sphalerite, native silverelectrum and tetrahedrite-tennantite; at Brunswick Mining, this element is contained mostly in the sphalerite, although tetrahedrite (and possibly pyrite) also contains minor quantities.

Jan 1, 1979

By J. Graham Eby

"This paper describes the development and some typical applications of Wemco's large-capacity flotation machines, the No. 120 and the No. 144, with volumes of 300 and 500 cubic feet, respectively. During the 1960's, it became obvious that low-grade orebodies would be mined at high tonnage rates - plants and grinding mills would be larger, which would create a demand for larger flotation equipment. To meet this demand, Wemco developed a single-mechanism, 300-cubicfoot cell, having five times the volume of the standard No. 66 cell. The average production rate of the No. 66 cell on porphyry copper ore was 100 tpd per cell; and it was our intention that the No. 120 (300-cu. ft) cell would handle 500 tpd per cell, with at least equal metallurgical results and power consumption per ton. The success and industry acceptance of the No. 120 cell has since led to the development of a larger cell, the No. 144, having a volume of 500 cubic feet."

Jan 1, 1972