Search Documents

By Lachezar Tsotsorkov

Corporate social responsibility Is a principal trend of the corporate strategy for sustainable development of Assarel-Medet JSC ? the largest Bulgarian company for open pit mining and ore processing the production activities of which date back to 1964. Sustainable development Social responsibility is considered as one of the three pillars for sustainable development, together with the economic and environmental responsibility.

Aug 1, 2013

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By Daniel Hodouin, Claude Bazin, René del Villar

"A traditional linkage has long been established at Laval University's Department of Mining & Metallurgy between the Mineral Process (MP) and the Mining Exploitation (Min) on one hand, and between the Extractive Metallurgy (EM) and the Materials Engineering (Mat) on the other. This academic separation of Mineral Processing from Extractive Metallurgy at the educational level has become increasingly at odds with today's industrial practice in which both disciplines are not only complementary but also often intertwined. For instance, in gold ore processing, comminution, flotation, and gravity separation units are interfaced with atmospheric or pressure leaching modules and with carbon adsorption and electrowinning units. The new copper plants in South America combine comminution and flotation circuits with heap leaching, solvent extraction and electrowinning processes.In order to reflect this new industrial reality and to harmonise the options offered in both its engineering programs, the Department of Mining and Metallurgy of Laval University has introduced major changes in its curriculum in 1996. These changes reflect also the recognition that the somewhat secondary status given so far to Mineral Processing and to Extractive Metallurgy within their ""mother"" programs, Mining/Mineral Engineering and Materials metallurgical Engineering respectively, was in sharp contrast with their actual significance for the Canadian economy. Leading industrial voices have raised similar concerns and the Canadian Engineering Accreditation Board has also addressed this problem in its latest program evaluation.The changes implemented at Laval aimed at a) better representing MP and EM within the two undergraduate programs; b) training top-level versatile and multidisciplinary engineers, fluent in all aspects of MP and EM, irrespectively of which of the two ((mother)) programs they had chosen and capable of meeting today's industrial requirements; c) training students in process analysis, optimisation and automatic control using state-of-the-art software, and d) taking into account the co-operative nature of both undergraduate programs.Results are very encouraging in terms of student enrolment and industrial response. However, some concern is expressed on the sustainability of the renewed curriculum considering the drastic budget restrictions in effect at Laval as in most other Canadian universities."

Jan 1, 1999

By J. A. Allan

OCCURRENCES of salt in Alberta have been mentioned and described by the writer in 1929 (l) and by Cole in 1930 (2). Brine springs occur at a number of places along the valley of Athabaska river north of latitude 56 degrees, and also on the south margin of Salt prairie, twenty-five miles west of Fitzgerald in the vicinity of the 60th parallel of latitude, which is the boundary between Alberta and the Northwest Territories. These salt springs were visited by Sir James Richardson in 1820, and in the same year D. W. Harmon stated that " ... clown Salt river there are several places where almost any quantity of excellent dean white salt may be taken with as much ease as sand along the seashore" (3). One hundred years later, in 1920, when the writer first visited these springs, the "dean white salt" which had accumulated about the springs was about 400 tons ( 4). This paper deals with a thick deposit of rock-salt which has been proved by drilling in the vicinity of McMurray. Particular attention will be given to a well drilled at Waterways early in 1936 by Industrial Minerals, Limited, when a continuous bed of rock-salt was penetrated with a thickness of 199 feet. As this paper is being presented, a salt plant is being completed and a production well is being drilled at the plant. < is salt deposit is in the vicinity of McMurray, close to the junction of the Clearwater and Athabaska rivets, in township 89, range 9, west of the 4th meridian. McMurray is about 240 miles northeast from Edmonton. As shown on Figure 1, Clearwater river, which rises at Methy portage, in Saskatchewan, enters Athabaska river at McMurray. Some three miles above the mouth of Clearwater river, the Hangingstone enters from the southwest. Waterways, where the latest salt development has taken place, is situated at the end of the Northern Alberta railway, a distance of 304 miles from Edmonton. This railway reaches the bottom of the Clearwater valley at Draper station, about 3 miles east of Waterways and near the mouth of Deep creek. The Draper bituminous sand plant is approximately half a mile east of Draper station. About one mile south of the townsite of McMurray, Horse river enters the Athabaska from the east.

Jan 1, 1937

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

By J. Nesset, F. Rosenblum, P. Spira

"Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 5000C. However, most concentrates show little or no propensity to selfheat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.INTRODUCTIONPrevious publications from this laboratory on the evaluation of self-heating in sulphides dealt with tailings backfill (Rosenblum et al. 1982) and waste rock (Rosenblum and Spira 1995). Sulphide concentrates may likewise exhibit self-heating in storage or during shipping. In a comprehensive but dated review, Kirshenbaum (1 968) pointed out the conflicting nature of information on means of controlling the problem, particularly with regard to the application of water and ventilation. Modelling by Simpson (1 97 1) of autogenous heating in stockpiled zinclead concentrate and associated field measurements by Wright et al. (1972) showed that the supply of oxygen by wind and the shape of the piles were the major factors in the development of hot spots. Simpson did not attempt to explain the complex mechanism of self-heating, simply ascribing its onset to oxidation. Pearse (1 980) investigated a potential method of testing for selfheating which consisted of (i) reaction with hydrogen peroxide and (ii) differential thermal anal sis, to characterize the response of concentrates at both ambient and temperatures above 100 C. He found the method sensitive enough to identify the need for careful handling but not to predict ignition. He recommended compacting concentrates and covering stockpiles with plastic sheeting to prevent ingress of air. All these workers recognized the key role played by oxygen and moisture in triggering self-heating."

Jan 1, 2001

By Kosuke Hosoda, Shuji Owada, Hiroyuki Tokuichi, Hirobumi Ohta, Chiharu Tokoro, Moto-o Sato, Katsushi Okumura, Hiroto Ogawa, Hideaki Umezawa

The Japanese government enforced the "Small Domestic Appliances (SDAs) Recycling Law" in 2013. The law targets metals such as Ta, Nd, Dy, Co, and W to be recycled. Considerable amounts of these minor rare metals are mounted on printed circuit boards (PCBs) of the SDAs and/or e-scrap (electric and electronic scraps). Although precious metals and copper can be recovered from the e-scrap in non-ferrous metals smelters, most of the minor rare metals report to the slag in these smelters in non-recoverable forms. These metals are often used in particular types of devices, and therefore it is possible to concentrate them by separating such devices before feeding to the smelters. In previous work we developed technology for "Device Separation" to concentrate several minor rare metals, but some problems remained, such as how to remove the PCBs from e-scrap bodies, and how to detach devices from PCBs after their removal from escrap bodies. This paper proposes a two-stage crushing process in which, firstly, PCBs are removed from the e-scrap body with various crushers, and secondly, devices are detached from the PCBs involving the application of elevated temperatures. It was found that in the first stage, crushers with physically flexible rotating media such as chains, which provide high collision probability with the sample and consume relatively low energy, can quite effectively separate the PCBs from the e-scrap bodies non-destructively. In the second stage, heating was found to be remarkably effective in helping to detach mounted devices from PCBs, also non-destructively. This paper will also discuss the detailed mechanism of the heating effect on the detachment of devices from PCBs.

Jan 1, 2014

By Vincent Roy

Numerous on going activities at the Daniel-Johnson Dam : ? Surveillance / monitoring ; ? Structural investigations & evaluation ; ? Injection work ; ? Crack mapping ; ? Instrumentation management (drawings & inventory) ; ? Drainage system state ; ? Foundation evaluation

Aug 1, 2013

By J. Chelsey Dawson

In presenting a thesis on this subject it is advisable to explain a few of the reasons for its seeming incompleteness. World progress has brought us to a position where approximations are not only to be condoned, but regarded as absolute essentials. Production in anticipation of demand is always accompanied by mistakes on the part of the producers. Only through trial and sometimes erring hypotheses may there be evolved the true course and theory upon which the steady triumphant march of world-wide industry depends. The average person likes to have everything placed ?before him in a clear and convincing manner. It is the impossibility of doing this which, in many cases, arises to confound the writer on shales. All that one can do is to present, as lucidly as possible, the known hypotheses&apos; and theories on the subject and leave the reader to study and work out the truth for himself. Many theories have been advanced on the origin of oil-shales ; some may be correct in certain instances and not in others; however, the writer will attempt no decision as to which are and which are not correct, but .will merely point out the relative merits of each. The figures given for reserves of oil and shale in different countries are only approximations and give but a rough idea of the true conditions.

Jan 1, 1925

By K. V. Phani Prabhakar, G. Padmanabham1, L. Subashini

Laser-arc Hybrid Welding (LAHW) is a relatively recent concept which effectively combines the advantages of laser welding such as the high depth of penetration, low heat input, high welding speed and the positive aspects of arc welding such as better edge bridging and possibility to add filler. For example, steel sections upto 12 mm thickness have been successfully welded in a single pass at a welding speed of 1 m/minute using a 3.5 kW CO2 laser in combination with a MIG arc. Maraging steel of grade M250 is widely used in the aerospace industry in thicknesses upto 10 mm. Conventionally, it is possible to MIG weld such thicknesses in 3-5 passes employing V-Groove joint preparation. However, this multi-pass welding results in formation of reverted austenite in the weld zone after post weld aging; and the high heat input widens the reverted austenite containing heat affected zone which is popularly known as the dark zone/eyebrow zone. Both these zones are detrimental to strength of the welded joint, specifically the fracture toughness. The width of the dark band is an important factor because, thinner the band, it is supported more effectively by the surrounding material. Therefore, in order to avoid multi-pass welding and reduce the overall heat input, single-pass laser-MIG hybrid welding was attempted on 10 mm thick maraging steel M 250 plates using a hybrid laser arc welding system comprising a 3.5 kW CO2 slab laser and a MIG welding system. Simultaneously, multi-pass MIG welds also are produced. Both the laser-MIG hybrid and MIG welds are characterized microstructurally and subjected to mechanical tests such as tensile and fracture toughness in as-welded and post weld aged condition. The amount and distribution of reverted austenite in the fusion zone and width of the dark band was found to be different. Hybrid welds showed a narrow dark band zone and improved mechanical properties. Laser-hybrid and MIG welding investigations carried out on thick section maraging steel M 250 will be presented in detail, including microstructure, tensile properties and fracture toughness of the welds. To the best of the knowledge of the authors there are no reports on laser-MIG hybrid welding of maraging steels.

Jan 1, 2014

By Jim Wickens, Vince Lofftus, Mark Kravetz

"This paper discusses how Bald Mountain Gold Mine (Ely, NV) dramatically reduced mercury production by treating process solutions with a liquid reagent based on organic sulfide chemistry. Cherokee Chemical Co. Inc. (Vernon, CA) markets this reagent as UNR 81 1A.A summary of the bench tests comparing various reagents is given. The ensuing plant trial is discussed and successful mercury removal results are presented. Data is presented to show that early removal of mercury in the process reduces the amount of mercury collected at retort. Data is also presented to show that use of this reagent does not reduce gold recovery. Plant trial treatment costs are discussed. Finally, the potential of this technology to substantially reduce closure costs as compared to traditional mercury removal options is discussed.INTRODUCTIONBald Mountain Mine produces gold. Mercury is a costly by-product of gold production because no revenue is generated from mercury. Traditionally, mercury leaches out with gold and follows the gold throughout the processing circuit until it is eventually condensed and collected at Retort. Minimizing or eliminating mercury production minimizes worker health and safety risks, minimizes environmental liability, and reduces costs. In the long term, minimizing mercury production will make mine closure easier and less costly.Bald Mountain Mine dramatically reduced mercury production by treating process solutions with liquid reagents called UNR 811 and UNR 811A. Several reagents were bench tested before proceeding with a plant trial. The reagent complexes the mercury to form an insoluble organic sulfide precipitate. In independent tests, the precipitate passed acid mobilization tests and is considered stable."

Jan 1, 2001

By V. J. Sopuck, O. P. Lavin, Ian Nichol

"A major challenge of contemporary exploration geochemistry is the development of procedures that can locate blind mineralization or mineralization that sub-crops below a cover of transported overburden, the composition of which bears no relation to the underlying mineralization. Over the past few years, the possible existence of diagnostic geochemical features in the country rock associated with volcanogenic massive sulphide deposits has attracted increasing attention both on the local mine scale and on the regional scale. In the present investigation, the nature of the geochemistry of a number of Archean greenstone belts of the Canadian Shield is examined to determine the feasibility of distinguishing productive from non-productive areas of copper-zinc mineralization. The results indicate that productive areas are distinguishable from non-productive areas providing consideration is given to the effects of igneous differentiation on rock compositionIntroductionArchean massive sulphide deposits are an important source of copper and zinc, and to a lesser extent silver and gold, particularly in Canada. As in the case of most other forms of mineralization, there is a continual need to develop new techniques that will improve the chances of success in the search for these deposits. The majority of Archean areas in the northern latitudes are overlain by a variable cover of glacial overburden. Considerable progress has been made in the development of new geochemical exploration techniques for use in glaciated terrain, based on the detection of anomalous dispersion in the glacial overburden. In certain situations, however, as in the search for blind deposits or in areas covered by glaciolacustrine deposits, overburden geochemistry offers little hope for success. In the case of massive sulphide deposits, one possible solution may lie in the detection of anomalous geochemical signatures in the bedrock. Recognizing this possibility, attention has been directed to the investigation of the nature of lithogeochemical dispersion associated with massive sulphide deposits on both regional and local scales, to establish the potential of lithogeochemistry as an aid in the search for these deposits."

Jan 1, 1980

By Robert Harris, Peter Pheeney

"The Murray Brook gold mine operated from September 1989 to March 1991. Approximately 1.2 million tonnes of gossan were mined from an open pit and treated at a rate of 900 tonnes per day. The facility applied an agglomeration vat-leaching cyanidation plant for gold and silver recovery. The leached ore or tailings were rinsed of residual gold and cyanide and placed on an adjacent clay lined pad for storage and containment. A 50,000 tonne heap-leach demonstration project was constructed at Murray Brook in 1992 to recover copper and zinc from ore located in a sulfide-rich zone occurring beneath the gossan. The operation proved unsuccessful because of poor recoveries and low metal prices. The project terminated in the same year.A corporate decision was made in September 1999 to undertake complete and final reclamation of the Murray Brook site. Jacques Whitford and Associates Limited were contracted to develop the final reclamation plan and to assist the company in presenting the plan to the New Brunswick government for approval. The government approved the plan in January 2000. Two important reclamation issues were the mobility of mercury from the gossan tailings and the potential of acid mine drainage from exposed sulfides. The mine site is situated upstream of a productive river system, and the issue or impact of chemistry changes to the environment over the long term became an overriding factor in the development of the reclamation plan.A resource assessment of the gossan tailings in 1999 indicated an average concentration of mercury of 40 ppm. The mercury occurred naturally as the mineral cinnabar, but the exposure to residual cyanide (less than 10 ppm) over several years in the pile has likely caused much of the cinnabar to decompose into more soluble mercury forms. The reclamation plan specified the replacement of all sulfides to the pit followed by approximately 600,000 tonnes of gossan. To ensure “fixing” of the mercury, the gossan was replaced in compacted lifts and both the remaining pile and that replaced to the pit covered with available till and compacted. The reclamation work was successfully completed in September 2000 and the chemistry of the receiving environment will be monitored over a three-year period, after which the company expects to achieve walk away conditions."

Jan 1, 2001

By V. J. Southey

"This paper reviews the history of Wabana Mines from 1892 to 1966, inclusive, in order to clarify the essential factors involved in the achievement of maximum mining efficiency and in the search for an acceptable product to satisfy changing market requirements. It outlines the progressive steps taken to mechanize both surface and underground operations, and forecasts anticipated performance, assuming certain major plans could have been implemented. Results of extensive research in the treatment of the complex ore are discussed. Selected processing alternatives are compared as to feasibility in a summary incorporating estimated capital and operating costs."

Jan 1, 1969

By S. J. Haynes

"This paper documents the characteristics of the different quartz veins, and their relation to gold, in the turbiditic Meguma domain of eastern Nova Scotia. Eleven different types have been distinguished in the greenschist facies on the basis of form, internal structure, mineralogy, wallrock alteration and crosscutting relationships to each other and to regional structures. Gold is present as rare visible disseminations in host rock slates and in ore-grade, early-formed veins, that pre-date the formation of upright Acadian folds and intrusions of Devonian granitoids. Four vein types pre-date Acadian folding. Five gold-deficient vein types are associated with Acadian folding (syndeformation); whereas two gold-deficient vein types clearly post-date this deformational event: Previously unreported, wall rock alteration is associated with early crosscutting and semiconcordant auriferous veins. In contrast, early stratiform veins are devoid of wallrock alteration. It is suggested that the auriferous vein arrays formed as submarine exhalitive systems over synsedimentary tensional faults and that the Meguma domain may represent the opening of a basin similar to the modernGuaymas rift .IntroductionThe term ""turbidite-hosted gold deposits"" is introduced to distinguish gold deposits contained within a turbiditic sequence of wackes and shales (or their metamorphosed equivalents) from gold deposits in other types of sediments. Usage and justification for the term is similar to ""carbonate-hosted lead-zinc deposits"" or ""volcanogenic massive sulphides"". A range of different characteristics can be present in individual deposits, some of which may be indicative of specific deposit types in the same manner that volcanogenic massive sulphides can be subdivided into ""Cyprus type"", ""Kuroko type"", ""Besshi type"", etc. Historically, gold deposits hosted by turbiditic flysch were an important class of quartz-vein gold mines in the 19th century. They included the goldfields of Victoria, Australia, Otago, New Zealand and Nova Scotia, Canada. Production from most of these fields had ceased by World War II and interest in this type of deposit waned. However, the recent exploration interest in gold has resulted in both re-assessment of the classical mining camps and the discovery that ""turbidite-hosted"" gold deposits are present in many parts of the world.Mapping of the regional geology and gold deposits of the Megumadomain of Nova Scotia was carried out by E.R. Faribault of the Geological Survey of Canada between 1886 and 1939. Faribault produced a comprehensive series of maps and reports for each gold district, a compendium of which was published by Malcolm (1929)."

Jan 1, 1987

By James R. Wickens, David La Rosa, Robert E. McIvor, Adrian Dance

"The comminution circuit at Barrick Cortez Gold Mine uses an open circuit primary jaw crusher followed by a standard SABC grinding circuit. The grinding circuit incorporates a 26’Ø x 11’ SAG mill, an Omnicone 1560 pebble crusher and a 16’Ø x 28½’ ball mill. Both mills are driven by 4500 HP motors.In 2007, several comminution circuit studies were performed to assess circuit performance and map a course for improvement. This paper discusses the results of those studies including an analysis of mine-to-mill opportunities, grinding work index efficiency, and ball mill functional performance. Subsequently, improvements to the circuit were made to enhance operating efficiency. Specifically, improvements to the pebble crusher liner configuration, advanced process control system (expert system) and ball mill classification and ball charge are discussed. In addition, other current and future improvement opportunities are discussed.INTRODUCTIONThe Barrick Cortez property is expanding to include the new Cortez Hills open pit and underground mines. Ore from these new mines will be processed in the existing Pipeline mill facility. In conjunction with ore characterization work, performance of the comminution circuit needed to be quantified. Thus, in 2007, the comminution circuit was surveyed and opportunities for improvement identified.Figure 1 below shows the Pipeline mill flowsheet. It is a standard SABC grinding circuit using an open circuit primary jaw crusher followed by a 26’Ø x 11’ (7.92m Ø x 3.35m) SAG mill, in closed circuit with a Omnicone 1,560 pebble crusher, and a 16’Ø x 28½’ (4.88m Ø x 8.69m) ball mill. Both mills are driven by 4,500 HP (3,357 kW) motors. The SAG discharge screen aperture is 5/16” (8 mm) x 1-1/16” (27 mm) slots. Ball mill circuit classification is done with Krebs D20B cyclones."

Jan 1, 2009

By Colin Lindsay

"The Collahuasi copper mine, located at an altitude of 4300 meters above sea level in northern Chile, commenced operations late in 1998. The mine is currently the 4‘h largest copper producer in the world and comprises an open pit, a 60,000 tpd sulphide concentrator, a 15,000 tpd oxide heap leach and SWEW plant and a 200 km concentrate pipeline to a port facility.Constructing, commissioning and operating a mine at high altitude presents unique challenges in terms of the performance of both equipment and people. It is important that these be recognized and carefully considered during the feasibility study and the detailed design stages and the success of the Collahuasi project is largely due to this. The plant design incorporates a number of features aimed at mitigating the problems of altitude and the construction methodology also took into account the particular site conditions.This paper discusses the Collahuasi project team’s approach to planning for the remote location and also some of the problems experienced during construction, commissioning and operation.INTRODUCTIONThe Collahuasi mine is located in northern Chile, some 250 km to the south-east of the port of Iquique and 15 km from the Bolivian border. The mine facilities lie between 3800-4300 m above sea level on the Altiplano, the central plateau of the Andes mountains, and cover a total of approximately 95,000 hectares. Although the area is arid, it experiences an average of 150 mm of precipitation annually and weather conditions can be extreme. Temperatures during the day range between -3 to +11 º C and are generally below 0ºC at night, sometimes as low as -20°C. High energy winds are common and humidity is low. Much of the precipitation occurs during the winter as snow but there also occurs a period during the Chilean summer known as the “Invierno Boliviano’’ (or Bolivian Winter) which is characterized by severe electrical storms and rain."

Jan 1, 2001

By Rudy Tenbergen, Dick Farmery, Jim Naylor

"Paste backfill has replaced cemented rock fill as one of the components to improve ground · control and mine safety at the Macassa Operation of Kinross Gold Corporation in Kirkland Lake, Ontario. It is the first operation to utilize "" flash thickening ""of very fine gold tailings to a paste consistency in the ""Paste Production and Storage Mechanism"", a joint technical development of Inco and GL&V. The tailings paste is mixed with alluvial sand to produce an engineered quality paste backfill. The development leading up to the decision to proceed with this novel technology is discussed, as well as commissioning of the backfill operation.IntroductionThe occurrence of a major rockburst on November 23, 1993 prompted a review of mining and backfill procedures at the Macassa No 3 shaft . This shaft is some 7238 ft deep and lies in a mining belt that is prone to seismic events. The recommendations were to change the mining from underhand cut and fill to mechanized long hole stopping and to look at alternatives to the rockfill backfill system in place. The Macassa cemented rock backfill operation, while producing the desired fill stiffness had drawbacks as compared to paste fill. With paste fill, placement rates are faster, more openings can be filled, it is less expensive and less prone to the occurrences of compensable incidents.Macassa mining personnel visited the Sudbury operations of Inco in 1993, where development on paste backfill was in progress. As some of the R&D was taking place with funding from the Premier's Council Technology Fund of the Ministry of Trade and Technology of the Province of Ontario , Inco personnel at that time did some feasibility and conceptual consulting on the use of paste fill for the industry. Inco had developed the use of alluvial sand paste fill, an engineered blend of alluvial sand and tailings fines and was doing development work to eliminate the ""conventional"" way of producing paste from mill tailing by thickening and filtration. This latter development work was taking place with GL&V Ontario. That work led to the filing of a joint Inca/ GL&V patent application for the PPSM, the Paste Production and Storage Mechanism with all marketing rights being held by GL&V."

Jan 1, 1997

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016