Search Documents

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Abstract-Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is confined by tectonic shear zones between marble and metapelites, extending laterally into the marble as tabular, pod or lenticular oreshoots (up to 50 m ?? 20 m ?? 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical profiles across mineralized zones confirm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the insitu supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly influenced by seasonal fluctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent flooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2 ~10-3.8 to 10-1.4) and oxygenated (fO2 ~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sulfides and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+ was transported into karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2 in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2 increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By R. S. Douglas

Introduction The operations of The Granby Consolidated Mining, Smelting and Power Company, L1mited, have always been concerned with the mining of low-grade copper ores. In the fifty years of this Company's existence, nearly 60,000,000 tons of such material has been successfully mined and treated. During these years, many changes in mining practice took place. However, at Copper Mountain, due to the large tonnages of very low grade material, it was realized that something more than changing mining methods would have to take place if these low-grade orebodies were to be mined at a profit and the Company and. its employees enjoy many years of successful operation and employment. Production costs were mounting commensurately with rising taxes and the increasing cost of supplies, labour, freight, and smelting, while the value of the product on the market was not increasing in price to compensate for the higher costs of production. A survey of the mineable ore in 1944 indicated that, of the 12,000,000 tons in the reserves, only 3,500,000 tons was now profitable ore. This reduction in the commercial ore reserves was a serious matter, as it meant that the mine had only two years of life at the profitable shipp1ng rate of 4,800 tons per day. Further, the location in the mine of the orebodies making up the 3,500,000 tons was not suitable for such high production.

Jan 1, 1950

By S. Vongpaisal, T. R. Yu

"A set of new blast damage criteria has been developed, with special reference to blasthole mining operations, for assessing damage by incorporating the vibration level, rock properties, site characteristics and the effects of ground support systems. The main objective of this work was to provide a database with reasonable accuracy for use in optimizing blast design, numerical analysis and ground control expert system module development.The new damage criteria allow one to estimate the degree of damage to rock structures in terms of a dimensionless parameter defined as Blast Damage Index (BDI). This allows for the description of blast damage in a unified form, and facilitates the development of codes for numerical modelling to express the degree of blast damage universally. A number of field investigations from several stope production and slot opening blasts at a large underground base metal mine were carried out to verify the developed index. The results show a good correlation between the observed damage and the type of damage predicted from the BDI values.Practical measures are also provided for minimizing blast damage in large underground blasthole mining operations"

Jan 1, 1996

By G. B. Harris, C. W. White

Cyanide has been used for the recovery of gold since the mid 1800s, but several jurisdictions have already banned its use, and environmental pressures are increasing to finding an alternative. Gold also forms chloride complexes similar to those of cyanide, but the use of chloride has never achieved widespread acceptance. This paper describes a chloride-based flowsheet, wherein the key unit process is the recovery and recycle of chloride ion. It is shown that the chloride-based flowsheet is competitive economically with the conventional cyanide-based flowsheets, and that it has a number of other advantages, particularly environmentally.

Jan 1, 2011

By K. Shen, A. J. Sinclair, N. Champigny

"Fluid inclusion studies from the Cinola deposit indicate low salinities and low C01 contents of the ore fluid. This supports a suggestion that the mineralizing fluids originated from pore water in the fluviatile host rock (mid-Miocene Skonun Formation). Bimodal distribution of filling temperatures suggests the existence of at least two temperature regimes centred on 160°C and 270°C during mineral deposition. Independent age and stratigraphic evidence indicates that depth of mineralization is between 1.1 and 1. 8 km, corresponding to a hydrostatic load of between 110 and 170 bars.RESUMELes donnees sur les inclusions fluides du gisement Cinola indiquent de basses salinites et basses teneurs en C01 . Ceci confirme que les fluides mineralisants ont ete derives de l'eau interstitielle prise dans les sedimentsfluviatiles hates. La distribution bimodale des temperatures d'homogenisation implique !'existence de deux regimes de temperature concentrees vers 160°C et 270°C pendant Ia mineralisation. La profondeur alaquelle le gisement s'est forme est evaluee d'etre entre 1.1 et 1.8 km a partir d'informations stratigraphiques independantes: ceci correspond a des pressions hydrostatiques de 110 a 170 bars."

Jan 1, 1982

By R. Barbaroux, J. -M. Lalancette, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"Arsenic released from the lithosphere by mining and metallurgical activities is a growing global environmental concern. Dundee sustainable technologies (“DST”) has developed a processing technology to sequester arsenic by means of vitrification. This method can effectively sequester arsenic trioxide without the need to oxidize from As (III) to As (V). Arsenic oxide is incorporated within a silica glass matrix that is stable as per the Toxicity Leaching Characteristic Procedure (“TCLP”) or EPA Method 1311. In this paper, the conventional treatment of arsenopyrite, commonly referred to as “two-stage roasting”, is discussed along with the options traditionally available for the remediation of the arsenic trioxide by-product. The drawbacks limiting the adoption of this processing flowsheet are discussed and a new processing route is presented for the treatment of arsenopyrite. This new flowsheet outputs an auriferous aluminosilicate highly amenable to gold extraction (> 96%) while eliminating the sulfur dioxide production associated with the second-stage roasting of pyrrhotite and ultimately uses vitrification as a definitive sequestration solution to arsenic trioxide.INTRODUCTION Faced with the depletion of conventional gold ores, the gold industry has witnessed a trend towards the exploitation of arsenical deposits. Arsenic is a naturally occurring metalloid often found in mineralogical association with gold. Many northern Canadian regions, from the Northwest Territories to Northern Manitoba, Northern Ontario and the Abitibi region are facing significant arsenic challenges. Projects are deemed uneconomic or prevented from going into operations due to the costs associated with handling arsenic material and there are penalties imposed to complex concentrates by smelters. In addition, Canadian mining operations have left an environmental legacy of gold tailings with grades typically of up to 9 grams per tonne with no processing solution as they also contain significant arsenic contamination at grades of up to 20%. Table 1 presents a list of Canadian deposits known to contain arsenic."

Jan 1, 2017

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber plant was recently completed at an existing facility, in order to treat the sulphur dioxide off-gas emitted from rotary kilns. Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong operational readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.INTRODUCTIONCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Quebec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary byproductof the process.Fresh hydrated lime and CDS residue is captured by the dust collection system and is re-circulated to the CDS via a fluidised transport system. Clean off-gas passes through the dust-collection system and is then sent to the atmosphere by a single exhaust fan.The CDS residue purged from the system is combined with the dust collected from the kiln offgas system and this mixture is wetted in the already exiting agglomeration system, to minimize dust generation during handling, and then sent to disposal."

Jan 1, 2016

By T. W. Wlodek

"AbstractThe results of research into the fatigue properties of SAE 1080 carbon steel and nickel-chromium-molylbdenum steel for mining drill rods are analysed and described in detail.The effect of water corrosion on the fatigue strength of drill rods of these two steels in the as-rolled condition has ,been investigated and the beneficial influence of shot-peening on their dry and water-corrosion fatigue strengths determined by employing the method developed previously (1).Eight S-N curves for as-rolled and shot-peened mining drill rods under both dry and water corrosion conditions have been derived and their shape and relative position are discussed. The main features relating to field performance of the drill rods are analysed.Purpose of Research and Outline of ProgrammeDRILLING holes in rock and ore by means of drill rods attached to a pneumatic drill is a basic procedure required in mining operations. Detonation of explosives placed in these holes is at present the only practical method of breaking down the rock and ore.A drilling rod is supported by its bit end in the drilled rock. Its shank end, fixed in the drilling machine, transmits impact energy to the cutting edges of the bit. On the field performance of the drill rod depend a number of basic mining operations such as sinking, drifting, and stoping. The drill rod is there-fore regarded as one of the most important tools used in the mining industry."

Jan 1, 1952

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By C. D. Rowe, H. S. Mitri, J. Malki, I. Vennes

Ore extraction at great depths creates high stresses around mine openings, which can result in violent rock failure in one of various forms of strainburst. This is especially true with strong and brittle rocks, which can store a large amount of strain energy that is suddenly released at failure. The strength and brittleness of rocks have been extensively investigated in the past. The most widely accepted method for the determination of rock burstability is the strain energy storage index obtained from a non-destructive uniaxial load–unload test. However, the results of this method are not always conclusive, showing less repeatability when the target test load is changed. This study concerns itself with the introduction of microscopic analysis as a tool to help validate the strain energy index results when burstability cannot be warranted based on mechanical property tests alone. In this study, two types of rocks, namely, basaltic komatiite (BK) and felsic norite (FNOR) obtained from Canadian underground mines are examined. The selection is based on the premise that felsic norite is known to be burstable from the mine experience, whereas basaltic komatiite is not necessarily burstable. A total of 60 mechanical properties tests were conducted including uniaxial compressive strength, Brazilian tensile strength, and load-unload tests. Laboratory tests on FNOR consistently exhibit high burstability; however, the results for the BK tests are not conclusive. To seek explanations for the mechanical rock behavior, 18 thin sections were examined with optical microscopy and image analysis. The findings show the tested BK specimens are dominated by alteration products, and all primary igneous minerals are lost. There is minor quartz, garnet, carbonate minerals, talc, and serpentine, which give the rock its ductile properties. The FNOR specimens are found to be relatively fresh and supported by a strong network of plagioclase with minor pyroxene, biotite, and secondary micas, explaining the higher stiffness. This study demonstrates how optical microscopy can complement mechanical property tests to evaluate burstability of rocks.

May 4, 2025

By Kevin M. Ansdell, Irvine R. Annesley, Christine L. Mckechnie

The U-Th-REE mineralization at Fraser Lakes Zone B is hosted by granitic pegmatites and leucogranites, which lie along the deformed contact between Paleoproterozoic metasedimentary gneiss of the Wollaston Group and Archean orthogneiss, approximately 25 km from the southeastern edge of the Athabasca Basin. The pegmatites/leucogranites are subcordant to concordant with the regional foliation and are concentrated within a northeast-plunging antiformal fold nose, the study area, which lies west of Fraser Lakes. The mineralized pegmatites/leucogranites in the western part of the study area (Group A) are typically enriched in U (± Th) with Th/U ~1, and contain uraninite, thorite, zircon, and allanite. Those intruding the central part of the study area (Group B) are generally enriched in Th and LREE, with Th/U >2, and contain monazite, thorite (commonly U-enriched), and zircon. The pegmatites and leucogranites in Group A tend to be slightly enriched in SiO2 and depleted in TiO2 relative to those in Group B and are interpreted to represent more evolved crustal melts. Both groups are peraluminous and show varied chemistry. Partial melting (~850ºC and 9 kbar) of a metasedimentary rock-dominated source, entrainment of accessory minerals as xenocrysts, and assimilation-fractional crystallization processes combined to enrich the granitic pegmatites/leucogranites in U, Th, and REE elements. Transfer of melt from the source region to the crystallization sites was assisted by deformation within and along major structural zones, such as the folded Archean-Paleoproterozoic discontinuity. The character of mineralization and structural control in the study area is reminiscent of the alaskite-hosted deposits at Rössing, Namibia.

Jan 1, 2013

By D. J. Robertson

"THE copper smelting operation of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, generates a gas flow of 350,000 c.f.m. at n.t.p. This gas stream passes to atmosphere through a 20-foot diameter by 250-foot brick stack, carrying with it an appreciable dust burden in the form of metallic oxide fumes. The flow constituents during the period 1952 and 1953 and •before gas filtration was included in the treatment scheme are shown in Table I. This paper describes the gas filtration treatment which was installed in 1957, using glass cloth media to recover this dust burden, and discusses the associated problem as its treatment for recovery of zinc and cadmium.The metallurgical details associated with the problem are illustrated by a description of the material flow sequence of the Company's hydrometallurgical zinc plant and copper smelter. In this ore processing complex, the zinc plant and copper smelter form an integrated unit within which intermediate zincrich products of each operation enter the treatment circuit of the other."

Jan 1, 1960

By Da-Qiang Cang, Qingde Wang, Wei Wang, Wen-Bin Dai, Min Guo, Yu Li

Utilization of both slag and its heat for hot slag is a great challenge for iron and steel industry. Many methods of hot slag modification for directly converting hot slag into value-added materials were researched in recent years, and waste heat of hot slag could thereby be transformed into inner energy or chemical energy of the materials. In this paper, an experiment of converting hot slag directly into glass ceramics by hot slag modification method was conducted. A cooled modifiers mainly composed of fly ash were firstly heated though a cyclone furnace and then fell into a molten bath to mix with hot steel slag. Half of hot slag was used as raw materials and accordingly about half energy consumption, about 5MJ/kg for melting raw materials was saved in the process compared with that of traditional producing method. Frit quenched from the modified hot slag had a higher basicity of 0.6-0.7 than traditional frits in order to reduce the needed amount of cold modifiers and accordingly utilize more hot slag and its waste heat. Glass ceramics were further prepared from the frit and a heat treatment of one-stage method is more suiter to such frit than that of two-stage method. The glass-ceramics with basicity of 0.6 and heat-treated by one stage method had the best performance with bending strength of 146.46 MPa, Vickers hardness of 6.79 GPa, water absorption rate of below 2% and shrinkage rate of around 10%.

Jan 1, 2015

By W. Leblanc, J. C. Marsh, D. Kettle, J. Tompkins, G. Hartley

"The Lingan Mine is the newest of the four operating collieries of the Cape Breton Development Corporation and is located on the east coast of Cape Breton Island. Development of slopes began in 1969 using four Dosco Roadheaders. Production commenced in October 1972, when a partial extraction section utilizing a continuous miner, loader and shuttle car was installed. A second Joy unit is scheduled to begin production early in 1973. This paper describes the production and development operations, the ventilation system and the equipment in use at the mine."

Jan 1, 1973

By A. F. Banfield

"IntroductionELEMENTAL sulphur occurs in three types of deposits: in salt domes in the Gulf Coast region of the United States and Mexico, from which over 90 per cent of world native-sulphur production is obtained; in sedimentary deposits such as those in Sicily, which are thought by some authorities to contain the largest world reserves of elemental sulphur; and as surface deposits, associated now or in the past with some phase of vulcanism, the type which bas the greatest world-wide distribution.Deposits of the volcanic type are the subject of this paper.From antiquity until the successful development of the sulphur-bearing salt domes at the beginning of this century, important sulphur production for local needs was obtained from volcanic deposits in many parts of the world. Due to technical and economic factors, however, producers could not compete in price with sulphur from salt domes. •The result has been that, except in Japan and Chile, little sulphur was produced from volcanic deposits from about 1910 until the start of the Korean war in 1950. Shortly after the outbreak of the Korean war, an acute world sulphur shortage developed and prices skyrocketed in many countries up to several hundred dollars a ton. Interest in volcanic deposits was renewed and exploitation of many was undertaken. Few of these operations have been successful, mostly due to inability of management to solve technical problems.While important volcanic deposits of elemental sulphur have not been reported ( 1) in Canada, and it is doubtful that any will be found, data presented in this paper may be of interest to students of ore genesis.This paper is based on field examination of numerous deposits of the volcanic type in North and South America."

Jan 1, 1954

By D. Hodouin

Jan 1, 1978

By Y. Okita

The Goro Nickel Process, developed over a ten-year period, uses a number of novel processing steps and treats two ore types, limonite and saprolite, together. Nickel and cobalt are solubilized using a 270°C pressure acid leach in sulphuric acid, which rejects the bulk of the Fe into the leach residue as hematite particles. The leach liquor, after CCD, is aerated to oxidize any ferrous iron to the ferric form and is neutralized with limestone to precipitate iron as hydroxides together with gypsum from the neutralization of the free acid. Further neutralization with lime, together with steps to remove suspended solids, reduces the iron to trace concentrations. Nickel and cobalt are directly recovered from the low-iron leach solution by primary solvent extraction using Cyanex 301® (SXl) in a high-strength hydrochloric acid solution. Nickel is subsequently separated from cobalt in a secondary solvent extraction circuit using tri-isooctylamine. A granular nickel oxide is made by pyrohydrolysis, and this allows the recycling of hydrochloric acid to SXl. The process is currently being commercialized to produce approximately 60,000 t/y of nickel as nickel oxide granules and approximately 5,400 t/y of cobalt as cobalt carbonate. This paper describes the process development to control the Fe concentration in the SX1 feed solution.

Jan 1, 2006

By R. C. A. Thurston

"The lack of notch ductility in structural steel in general, and in ship plate in particular, has been the object of widespread attention in the metallurgical world since the spectacular collapse of the ill-fated S.S. Schenectady in 1943. Numerous investigations have been carried out, many new tests have been developed, and a vast amount of useful data has been published, with the result that our knowledge is now far more advanced than it was at the time of this disaster. Interest has focused largely on the medium strength steels, and the various factors which cause a normally ductile steel to behave in a brittle manner in the presence of a notch and at relatively .low temperatures have been thoroughly studied.The literature available on high-tensile steels, however, is less extensive and the present paper is intended to supplement this information. Notch toughness tests have been carried out, at the request of the R.C.N., on a high-tensile manganese steel in the form of commercial ship plate. One of the newer tests, the tear test, and the Charpy V-notch impact test, were used to examine the characteristics of plate for the construction of an ice-breaker. About 250 plates, mainly in the thickness range from 11,4 in. to 1 % in., were tested. An an-alysis of the results obtained is presented, certain aspects of the tear test are discussed, and the correlation between the two types of test is studied. On the basis of information available from casualty ships, the plates, with few exceptions, were considered to be satisfactory."

Jan 1, 1959

By H. J. H. Pieterse

Agitation requirements in oxidation autoclaves can vary widely depending on the mineralogy of the feed material and the specific process selected. Before selecting an agitation system it is important that the client specify the desired throughput, mineralogy, chemistry, kinetics, compartments, overall retention time, and the desired oxygen utilization. In selecting the agitation system, the factors mentioned above as well as oxygen solubility, oxygen mass transfer coefficients, and specific power are evaluated. Much research effort has been directed toward open tank systems for fermentation and oxidation processes. However, for high pressure autoclave oxidation processes little information is available. In this review the author's experience in the autoclave industry and some of the available literature are utilized to compare the installed power per unit volume with some of the methods proposed for open tank oxidation. Equations that appear to give results close to that experienced in the industry have been identified. Further work is required in this area to develop a higher degree of confidence in the ability to predict the power required for any given case.

Jan 1, 2004

By Xiao min Zhou, Yan Xu, Hongzhen Liang, Xiaonan He

"With the increase of shaft excavation depth, the thickness of the shaft lining increases sharply. It is difficult to reduce thickness of lining effectively by improving high-strength concrete performance. The concept of the New Austrian Tunneling Method (NATM) is that surrounding rock plays a certain role in tunnel support. The solution should be to find the correct relationship between shaft lining thickness and rock strength, which is related with the interaction between the surrounding rock and concrete lining. The plane strain mechanics model is introduced to calculate lining thickness. Shaft lining design of Cixi Colliery in China is completed with the mechanics-based method proposed in this study. The lining design is verified through numerical simulation and field monitoring. The simulation results show that the maximum mises stress is located at the inner edge of the shaft lining. The increase of lining thickness cannot effectively reduce concrete grade. The monitoring results indicate that a lining design thickness of 900mm with C60 concrete, is safe and reliable in the shaft over 1000metres.This analytical design method can well be referenced in similar deep shaft projects.INTRODUCTION The New Austrian Tunneling Method (NATM), thought to have helped revolutionize the modern tunneling method, is the most extensive design philosophy and construction principle in today's tunnel engineering. It began to attract attention in the 1960s based on the work of Ladislaus von Rabcewicz, Leopold Müller, and Franz Pacher in Austria[1]. NATM was originally developed for tunneling in depth and in high situ-stress conditions in the Alps. The history of sequential excavation was reviewed, which highlights the progress of tunnel design and construction in Europe after NATM[2]. Structural conditions were introduced into the equilibrium of tunnels in NATM, and the additional force was estimated to stabilize the excavation of the tunnel[3].From the perspective of applied mechanics, there was no accuracy theory to explain the interaction between the tunnel structure and the surrounding ground. Numerical calculation is an effective means to study the basic mechanism of tunnel excavation[4].Based on two-dimensional modeling approaches in the past, such as NATM and other derivatives, a three-dimensional model was studied to"

Jan 1, 2019