Search Documents

By Van Heuzen JA

The extensive deposits of brown coal in the Latrobe Valley form the major solid fuel resource in Victoria and are the energy source for most of the State's power generation. This paper describes the coalfield resources allocated for electricity generation and a potential sequential develop- ment of these areas in future years to supply future power stations.

Jan 1, 1982

A survey of leaching systems for the dissolution of gold has been undertaken and their advantages and disadvantages evaluated both from their effectiveness at leaching and their compatibility with carbon- in-pulp (CIP) and resin-in-pulp recovery. In the near future it is almost certain that cyanidation in some form will remain the leaching system of.choice although economic and environmental pressures could see the introduction of other leaching systems particularly for treating refractory gold ores. The most likely alternative leaching systems appear to be acid chlorine, acid thiourea and ammoniacal thiosulphate. INTRODUCTION High grade reserves of readily recoverable gold ores are gradually being depleted which, inevitably, must create a greater awareness amongst gold producers, of the efficiency and, in some cases, the suitability of present day metallurgical processes for treating low grade, complex and refractory deposits. One of the key steps in the extraction of gold is the dissolution of the metal using chemical reagents which, ideally, should be cheap or recyclable, selective, non-toxic and compatible with down-stream recovery processes. In practice, meeting all these critera is difficult - if not impossible - particularly in view of the stringent environmental impact requirements which must be met Nowadays.

Jan 1, 1982

Mixers are commonly used for the transfer of oxygen in gas-liquid-solid reactions in minerals processing. The process rate is usually controlled by two steps: gas-liquid mass transfer and reaction kinetics. Some examples are described along with the factors used for analysis of the mass transfer design problem. Typical oxygen rates and appropriate types of aeration systems or mixers are reviewed. The commonly used Rushton turbine has limitations in a number of mineral processes. The development and characteristics of the LIGHTNIN A315 axial flow gas dispersion impeller are described. Some practical examples which highlight its advantages are briefly described.

Jan 1, 1992

Alternative processes for converting coal to liquid products and their stage of development are outlined. The merits of hydrogenationprocesses in general, and the solvent refined coal process in particular, are stressed. Bench scale experimental hydrogenation procedures used by the Australian Coal Industry Research Laboratories Ltd. (ACIRL) to study the liquefaction of Australian coals and correlations between properties of such coals and their conversion to liquid products are described. Factors involved in assessing investment and operating costs for modern hydrogenation based coal refineries of different capacities are described with reference to a recent study undertaken in N.S.W. The significance of coal properties such as yield and yield structure of total liquid products and how they and other factors can influence the economics of the coal refining operations are discussed.

Jan 1, 1977

By Hill J. R M, McDonald M. M

A prediction technique for support perfor- mance of hydraulic backfill in narrow stopes is applied to two stopes separated vertically by a sill pillar. Predicted stope wall closures and fill pressures compare favorably with field measurements taken over a period of several years at two mines in the Coeur d'Alene dis- trict. Stope wall closure and peak pillar stress can be substantially reduced by improved fill quality within a practicable range of fill and rock properties.

Jan 1, 1973

Application of Agitated Leaching for Iron Removal from Silica Using Sulfuric and Hydrochloric Acid In this research, iron removal from silica used in glass industry was investigated using agitated leaching method. Silica sample was provided from silica concentrate originating from Chalchoog Silica Mine located in Abhar, Iran. The sample contained silica, iron oxides and clay minerals. For characterization of samples XRD and XRF analysis and atomic absorption method were applied. Silica and iron oxide (Fe2O3) grade of head sample was 98.41 per cent and 0.067 per cent respectively. Two inorganic acids (sulfuric and hydrochloric acid) were used in agitated leaching tests. Two series of L9 orthogonal array of Taguchi design with replication were used to determine the effect of parameters including acid dosage, leaching duration, ambient temperature and solid content on iron removal. The statistical calculations and analysis of variance (ANOVA) were carried out by means of DX7.0, Minitab14.0 and Winrobust1.02 softwares and also statistical calculations were checked manually using Excel software. Also multivariate regression was applied in order to forecast Fe2O3 conent of final product. The optimum conditions for leaching tests which sulfuric acid was employed are as follows: 40 minutes leaching time, temperature of 85¦C, 40 g/L acid concentration and solid content of 20 per cent. Under this condition the amount of iron oxide in silica was decreased to 0.042 per cent. The optimum conditions for leaching tests which hydrochloric acid was employed are as follows: 80 minutes leaching time, temperature of 75¦C, 30 g/L acid concentration and solid content of 20 per cent. Under this condition the amount of iron oxide in silica was decreased to 0.035 per cent.

Sep 13, 2010

By Little T. N

The Western Australian School of Mines is continuing to investigate the blasting techniques and mining strategies that are used for ore/waste separation (or high grade/low grade ore separation) or to prevent ore and waste mixing. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and undergoes no mixing of the various identified ore and waste blocks and is fully recovered at the minimum overall operating cost. The current study includes the use of computerised Knowledge Based Systems (KBS) technology to assist the user with the blast technique selection and blast design process. These aspects are highly dependent on the geology. (geometry, rock mass properties, grade distribution), explosive performance and the expectations of the mining company in terms of production rates and equipment utilisation. Most of these factors are not well defined and nor are they easy to quantify. However, a large amount of knowledge does exist and is available in the following forms: rules of thumb, empirical formulae, engineering judgement and past experience. KBS techniques are well adapted to handle such"forms of knowledge. The primary objective of this paper is to illustrate an approach for the use of Knowledge Based Systems during the analysis and interpretation stages of the blast design process. In particular, the components and methodology of the developed system are described for selective open pit gold mining. The Knowledge Based System developed was written using the declarative programming language PROLOG.

Jan 1, 1990

By Leung L, Downey M

This paper presents an overview of a technology package developed by BHP for locating discontinuities in coal seams using an in-seam seismic (ISS) exploration technique. The technology package includes instrumentation, data processing software, field procedures, numerical modelling and interpretation know-how. The technology developed has proved to be highly successful; features such as faults and dykes, not detected by other methods, have been delineated. Using equipment specifically designed for underground use, surveys are carried out quickly and at low cost. More than 30 ISS surveys have been conducted by BHP in Australia. Substantial savings in production revenue have been realised in situations where ISS has identified mining conditions which would have impeded longwall operations. Case studies of several ISS surveys are described in the Paper.

Jan 1, 1987

By Kuipers A. J

Aberfoyle has been applying computer methods to mine geology in small to medium-sized underground mines since the early 1980's. Recently, the installation of DATAMINE software at the Hellyer Mine in Tasmania has allowed development of computerised applications which assist both mine geologists and mine planning engineers on a daily basis.Comprehensive data is entered into a database prior to survey coordinating to produce a processed database which can be accessed for construction of a variety of plots. The folded and faulted nature of the orebody contacts at Hellyer has necessitated the use of the structure contour method to provide a complete 3-D spatial interpretation. Computer-generated contact intersection points are hand-contoured before digitising and wireframing as a digital terrain model. This wireframe model can be sectioned in any plane for mine planning.

Jan 1, 1990

By Liu Y

Mathematical modelling of scrubbers in development and longwall operations in underground mines produces useful results. Mathematical modelling on the mounting of scrubbers on longwall supports shows that the number of scrubbers and the air quantity through the scrubber are the two important parameters. Increase in both these parameters results in decrease in dust levels at the tail gate. The critical factors are scrubber efficiency and the ratio of the air through the scrubber/total air quantity.Results of parametric studies conducted to establish factors which have dominant influence on the effectiveness of the scrubbers on dust levels and high gas build-up in the scrubber show that for use of scrubbers in development headings, the order of importance of parameters in relation to dust concentration in the scrubber area is: scrubber efficiency, rate of production, specific dust make/tonne, leakage factor, intake dust concentration, recirculation factor and air quantity through the scrubber.The equations developed for mathematical analysis and the detailed results of modelling provide useful data on recirculation of emitted gas in the use ofscrubbers for dust control.

Jan 1, 1995

The application of reinforcement techniques to enhance the stability of underground coal mine roadways subject to high stresses is discussed. Research conducted in the Illawarra Coal Measures has been aimed to delineate the factors which influence the behaviour of rock above roadways and the performance of the reinforcement placed. Design considerations for the reinforcement of mine roadways in the Bulli coal are based on a quantification of the rock response together with a reinforcement strategy to enhance the structural integrity of the roof strata.

Jan 1, 1986

Geological. engineering is a field of engineering practice concerned with design and construction of excavations and structures in soil and rock masses. The role of geological engineering in mining practice is defined in this paper, and the scope of the various disciplines in engineering science and geoscience which support geo-engineering research is discussed. The current national research capacity in geo-engineering is considered, and current and future needs for geo-engineering research for mining practice are proposed. Education programmes to sustain the proposed level of research and its industrial implementation are Suggested.

Jan 1, 1986

By Hiddlestone D. C

Effective exploration, testing and analysis is essential for good process design and optimisation of coal preparation plants. Coal processing relies on the sizing and washability characteristics of the particular coal to define the most cost effective design to meet the market requirements. Flowsheet development and equipment selection is dependent on the natural quality characteristics of the coal, its physical properties and the value of the final product in its market. The methodology of process selection and the key elements in design are discussed. Coal is consumed in two general markets: ò steaming coal - both domestic and export, and ò metallurgical coal. This paper discusses the typical economic analysis required to evaluate the potential for, and cost benefit of, providing the flexibility to switch coals between markets. A case study illustrates the methodology of process selection in a typical high value metallurgical coal.

Jan 1, 1997

Since the announcement of early experimental work on rotating magnetic field (RMF) separation at the Sixth Mill OperatorsÆ Conference in 1997, the concept of RMF separation has been developed and tested further, and a range of separator designs is now being developed for the mineral processing industry. Shortened, but full diameter, prototypes of these designs are now available for test separations. The main advantage of RMF low and medium intensity attraction separation is the significant reduction in particle entrapment. This reduction is so significant that RMF separators are capable of operating very close to their theoretical limit for separator precision. This makes small laboratory RMF attraction separators ideal for low to medium intensity magnetic sample analysis, and larger separators ideal for applications requiring sharp magnetic susceptibility splits. Feedrates and separation rates are comparable to those of conventional attraction separators. Although RMF attraction separators are now well advanced in development, RMF rotation separation is still in the early experimental stage. The exception to this is the dry particle rotation eddy current separator that offers eddy current separation of small non-ferrous metallic particles from about 2 mm down to about 100 microns. Wet small particle eddy current separation is also possible, but has not yet been developed to a practical stage.

Jan 1, 2000

By Hossaini SMF

After reviewing the various approach es,namely, empirical,analytical.observational and numerical, a logical systematic approach is proposed for the estimation of compressive strength of coal pillars. In this approach first,uniaxial compressive strength of coal in pillars is estimated,taking into account the size effect and the effect of discontinuities. Next,the compressive strength of coal pillars is estimated by determining the stress distribution in the pillar and the Bieniawski strength criterion. The results appear to be compatible to the ones obtained by Wilson's method. The traditional pillar design equations give improper answers for deep workings.

Jan 1, 1991

In attempting to vegetate pnob!em sites some basic pn.i,ne%ptes, namely the phys.ica.e and chemi.ca2 pnope/ti;es og the problem mateni.al and the selection oU hu.itab.2e p!antts {cor pnopagati.on, have to be considered. Pnobtem sites such as tai ing dams, mined-out atteas, and areas which have been genehaUy advehse2y a46eeted by mining activities, are not only o~ten located in a divehs.ity o4 climatic regions, but they also usuaUy dL64en substantially in theAjt .int' Lns c phys.ica2 and chem.i cat pnopen t i.es . To estabP.ish vegetation on such sites 6requent2y requites: .%) The ame Lonaton oU adverse {yaetors in onde t to exeate a hoot env.utonment suitable Uon "satis1actony" plant growth. .%i) These.2eationo4 plant species suited to the improved Hoot env.utonment, and eompat%b&e with the e2imate o{y the site, and the ultimate Land use o4 the site. iii) The estabL shment o{y a Laboratory and p-LLot scale testing programme to aeeomptizh the above.

Jan 1, 1976

By Armstrong M, Kleingeld W. J

Current low prices for many metals mean that deposits have to be mined at high cut-offs (relative to their mean grade), which means that only a small percentage of mining blocks are above cut-off. Worse, at such high cut-offs, the blocks above cut-off are usually not grouped into convenient clumps for mining; they tend to be split into small isolated patches that are difficult to reach and hence expensive to extract. Companies wishing to acquire mineral properties have to be able to work out quickly what percentage of blocks are above cut-off and what can effectively be mined given the mining method envisaged. Moreover they need this information within a relatively short-time. The work presented here relates to typical South African gold mines (ie tabular orebodies) but the long-term objective is to develop tools for quantifying the impact of reserve breakup at high cut-offs for a wide range of underground mines including those that are not tabular. The mining method and the sampling procedure determine whether ore blocks can effectively be located and extracted economically. This project studied the impact of these two factors on the recoverable reserves for Witwatersrand gold mines. In order to be repeatable, the tests were done on numerical models of the deposit obtained by geostatistical simulations. To ensure realism, the orebody model and the mining scenarios were based on a specific mine. The recoverable reserves (ore tonnage above cut-off, the corresponding metal quantity and the average grade) were calculated for a wide range of cut-offs for four mining scenarios, as well as for the base case of free selection: ò Scenario 1: Blocks are taken if their true grade is above cut-off and if they are accessible from a raiseline (no information effect, no marginal blocks). ò Scenario 2: In addition to the accessible pay blocks, adjoining marginal blocks are taken (no information effect, + marginal blocks). ò Scenario 3: Blocks are taken if their estimated grade is above cut-off and if they are accessible from a raiseline. Here the estimator is the average of the face samples (information effect, no marginal blocks): ò Scenario 4: Accessible pay blocks are taken if their estimated grade is above cut-off. Adjoining marginal blocksare also taken (information effect, + marginal blocks). ò Free selection: All blocks whose true grade is above cut-off are taken irrespective of their accessibility. The results can be presented in different ways, for example by plotting ore tonnage above cut-off versus cut-off grade, or metal tonnage above cut-off versus cut-off grade etc. As expected, this shows the hierarchy between the five scenarios from the free selection base case to scenario No 2 (true accumulations, pay +

Jan 1, 1995

By Weller K. R, Stewart P. S B, Restarick C. J

The performance of the Renison tin concentrator was assessed in detail for two arrangements of the three available ball mills. With two mills used for primary grinding and the third for regrinding table tailing, the concentrator recovered 65.3 per cent of tin in the three tin concentrates produced by tabling, vanning and flotation at a calculated overall grade of 37.5 per cent tin prior to batch dressing. In the second arrangement one mill was used for primary grinding and two mills for separate regrinding of table tailing and sulphide concentrate. The metallurgical effective- ness of the change was somewhat obscured by unintended changes,i.e. an increase in the assay of the fresh feed from 1.38 per cent to 1.1+6 per cent tin and unresolved changes in the sulphide rougher flotation and tabling. However, using the results from a detailed size by size analysis of the behaviour of ore components in appropriate parts of the plant, it proved possible to show that, had the two unintended changes not occurred, up to 5 per cent

Jan 1, 1977

By Kyle J. H, Browner R. E

The selective adsorption of gold cyanide by the weak base ion exchange resins, PAZ-4* and Duolite A-7*, the neutral polymeric adsorbent, Amberlite XAD7*, and the strong base resins, PAZ-8 and IRA-400+ have been studied in both low and high salinity waters, and performance compared with activated carbon. The selectivity of the neutral polymeric adsorbent and activated carbon for gold decreased in highly saline water, while the selectivity of weak and strong base resins for gold increased in highly saline water. This supports the contention that the adsorption mechanism for neutral polymeric adsorbents and activated carbon is the same. Copyright

Jan 1, 1992

By Parsons A. E

The application of known pelletizing tech- nology was successful in the agglomeration of zinc concentrate into pellets of minus 6mm siz- ing using fine zinc calcine and sulphuric acid as binder. Subsequent roasting trials conducted in a 0.3 m diameter fluid bed reactor, showed that the pellets satisfactorily withstood hot physical abrasion during fluidization. Fines generation was low and the pellet calcine was hard, possessing excellent handling properties. Results of laboratory scale static pellet sinter- ing tests showed conclusively that the deterior- ation in sinter physical quality experienced with fine calcine was not apparent when the calcine was added to the mix in pellet form. Based on the results of small scale exper- imental work, a one tonne per hour pilot plant was constructed and operated. Several thousand tonne of pellets were produced-for fluid bed roasting in Badische Analin and Soda Fabrik (B.A.S.F.) turbulent layer (T.L.) roasters previously designed for roasting iron pyrite concentrate. Continuity of the T.L. fluid bed roasting operations was achieved when the waste heat boilers were replaced with atmospheric coolers and thus eliminated the problems of gas flow restrictions. Sinter plant trials were conducted over a period of two weeks with the addition of pellet calcine to the sinter feed. Results showed a marked improvement in sinter plant performance, and as a result of better bed permeability, increased sinter production was achieved, with- out significant deterioration in sinter quality.

Jan 1, 1974