Search Documents

By D. R. Uhlmann, T. P. Seward, K. A. Jackson, J. D. Hunt

microscopic ohservations on alloys of organic trzaterials show that dendrite arms can melt off under normal conditiorzs of growth. This occurs because of the interactiorz of' heat and matter fluxes during dendritic growth. The re melting occurs where the den-drite arms are joined onto the main deizclrite sterrz. Many detached crystals can be produced in this fashion. It is postulated that this remelting phenornenon occurs in metal alloys, giving rise to the equi-axed region in castings. Experiments peyformed orr castings of transparent materials support remelting as a primary source of detached crystals. Ob~ervations an equiaxed tones in metal castings are discussed in terms of this and other mechanisms. It is concluded that the partial remelting of dendrites is on important mechanisnl for producing the equiaxed regions in castings. THE freezing of a casting can be divided into three regions: a chill zone formed near the mold wall, a columnar region, and a third region, at the center of the casting, which is called the equiaxed zone. The origin of the grains that comprise the equiaxed region is the subject of this paper. We will first outline the mechanisms which have been proposed to account for the origin of the equiaxed region and discuss some recent experiments which cannot be explained by these theories. We will then present some microscopic observations of dendritic growth which have led us to conclude that the equiaxed zone in castings can arise from partial remelting of dendrites. This proposal is supported by observations on transparent castings. Finally, we will discuss several observations on metal castings which could not be explained previously, and which can be accounted for by the present proposal. Previous Mechanisms. Winegard and Chalmers3 pointed out that the molten central region of an ingot could be constitutionally supercooled, because of the solute layer at the growing interface. In this supercooled region, nucleation on particles could occur, giving rise to the equiaxed crystals. Another mechanism has also been suggested,4y5 that the nuclei originate in the chill zone then float or are carried by convection to the center of the casting, where they grow to produce equiaxed crystals. In this case, all the crystals nucleate immediately on casting, so this mechanism will be termed "big-bang" nucleation. Walker's Experiments. J. L. Walker has made observations on the solidification of nickel and Ni-Cu alloys which cannot be accounted for by either of the above mechanisms. In studying the grain size resulting from freezing of nickel at various undercoolings, walker6 found that at large undercoolings the grain size was small, due to mechanical nucleation, as discussed by walker7 and Horvay.' At small undercoolings, the grain size was large, and the growth dendritic. In Ni-Cu alloys, however, for initial undercoolings starting from just below the melting point and extending for a hundred or so degrees of undercooling, fine grains were also observed. Samples were undercooled 200 Centigrade degrees without nucleating, and were then heated 130 Centigrade degrees so that the undercooling was 70 Centigrade degrees, and nucleated. The samples had a small grain size, indicating multiple nucleation. There were no heterogeneous nuclei in the liquid which could operate at the temperature of growth. Constitutional supercooling could not have been greater than the supercooling of the initial melt, since the temperature rose as the freezing continued. walker -as also shown that a Ni-Cu alloy which can be undercooled to below its solidus will produce typical columnar and equiaxed regions when cast into a cold mold. This alloy could not reach a temperature below its solidus by constitutional supercooling. It could not, therefore, have nucleated heterogeneously. Neither the big-bang mechanism nor the Winegard-Chalmers mechanism can account for the fine grain

Jan 1, 1967

By James E. Howard

AT the request of the Council of the Institute, I have the honor to submit the following remarks upon the Program of Tests under which the current work of the Watertown Arsenal Testing Laboratory is carried on, which comprises, among other items, the tests of steel ingot metal and derivative shapes. The intended scope of the tests may be illustrated by extracts from the descriptive part of the program as submitted by the Laboratory under date of April 17, 1907, and subsequently approved by the Chief of Ordnance, U. S. A. Under Item 1, Ingot Metal-Open hearth, acid and basic; Bessemer, acid and basic; crucible; fluid compressed and uncompressed-descriptive remarks were made as follows ; " A thorough, fundamental inquiry into the physical properties of steel necessarily begins with the ingot metal. Investigations, having for their object the improvement of steels, should also begin with the ingot. A knowledge of the ingot structure is essential for judging of the subsequent behavior or appearance of the metal. Under ordinary conditions, so little information is obtained from the ingot in individual cases that practically none of importance is acquired. These remarks have particular reference to the state of physical and structural soundness of the steel. Questions of chemical composition, segregation, piping and the grosser cavities have frequently been given attention. Defects of continuity of structure, which manifest themselves in the working; of the metal, and at the final stages cause distrust in the finished forging, have generally been neglected. ? The range in physical properties in a given composition of metal, as shown in Tests of Metals, 1902 and 1903, is very great. Tests are there found which, when the results are

Mar 1, 1908

By A. Grant Elliot, H. W. Lavendel

qualitative picture has been developed to describe the oxidation behavior of TaSi2-coated tantalum and CbSi2-coated columbium. These systems have a significantly lower inherent oxidation resistance than MoSi2-coated molybdenum does. This stems primarily from the fact that Ta2O5 and Cb2O5 are nearly as stable thermodynamically as SiO2, whereas MoO2 or Moos are not. Further, diffusion of silicon in the Ta- and Cb-Si system is considerably slower than in the Mo-Si system. These ,factors prohibit the mechanism of selective oxidation of- silicon which accounts for the oxidation resistance 01- MoSi2-coated molybdenum. The silicide can be stabilized by adding suitable Modifiers which increase the thermodynamic stability of the silicate formed during oxidation. Modifiers, such as aluminum, can be inroduced into solid solution in the coating. in controlled amounts through proper selection of the source in the pack cementation process of coating fov~rzatiorz. Addition of aluminum to TaSi2, coatings on tantalum was effective in moderately increasing the oxidation resistance. EXTENSIVE experimental work and analysis have established the nature of the oxidation behavior exhibited by MoSi2- and MoSi2 -coated molybdenum-base alloys, and defined the conditions for maximum protection against oxidation of the substrate.'-* The oxidation resistance of MoSi2 in the temperature-pressure range of 1100°C-PO2 > 10-5 atm to 1900°C— PO2 > 10-1 atm is due to the formation at the surface of a continuous film of SiO2 which results from selective oxidation of silicon. Under the prevailing kinetic conditions, this film is stable toward the molybdenum silicide with which it comes in contact. Initially molybdenum oxidizes also, but it forms volatile species. SiO2, however, nucleates and grows as a condensed phase. Once a continuous film of SiO2 has formed, the oxidation rate falls to that observed for the oxidation of pure silicon indicative of diffusion through the oxide film as the rate-controlling mechanism. This oxidation behavior is of course highly dependent upon temperature and oxygen pressure. Bartlett and Gage13 and Bartlett, McCamont, and Gagelb define precisely this dependence in terms of the oxygen partial pressures and silicon diffusivities required to support a stable SiO2 film. At low temperatures (near 500°C—the "pest" region) silicon diffuses too slowly to be selectively oxidized. Hence, molybdenum and silicon oxidize readily in proportion to their stoi- chiometry. At high temperatures and low pressure, SiOz dissociates to form volatile SiO(g), and a protective film cannot be maintained. Application of the MoSiz/Mo system is limited to temperatures below 1900oC, the eutectic between MoSi, and MO5Si3.5 The oxidation behavior of MoSi2-coated molybdenum is essentially the same as that outlined above with the exception that the MoSi2 is not in equilibrium with the molybdenum substrate. At the temperatures under consideration silicon will diffuse rapidly into the molybdenum eventually converting the coating to MosSi3.4 The rate constant for subsequent decomposition of Mo5Si3 into Mo3Si plus silicon, and/or the diffusivity of silicon through Mo3Si then becomes low enough to allow active oxidation of both molybdenum and silicon with subsequent degradation of the specimen. A stable silica film can be formed but at temperatures and/or oxygen partial pressures higher than those required with MoSi2 present as a source of si1icon.l, 4 Because of the similarity between the silicides of molybdenum and those of columbium and tantalum one would expect similar oxidation behavior for coatings in the respective systems. This is not entirely the case, however, as shown by the experimental results reported herein. Regarding tantalum and columbium disilicide coatings on tantalum and columbium substrates, respectively, the oxygen arriving at the surface of the coating partitions itself nearly equally between the metal and the silicon, and a two-phase oxide layer (Me2O5 plus SiO2) is always formed. The diffusion of silicon in the tantalum and columbium silicides is relatively slow, compared to that in the molybdenum silicides, which further enhances this equipartitioning of oxygen. Thickening of the coating during service by inward diffusion of silicon into the substrate is correspondingly slow, and the effective thickness of the coating at the roots of cracks and defects is only slightly changed providing high probability for premature coating failure. Furthermore, the SiO2 glass that is generated is not thermodynamically stable with respect to the coating. The metal silicide tends to reduce the SiO2 liberating either free silicon or SiO. The situation can be improved by suitably modifying the coating such that the stability of the protective glass which is generated during service is increased. Thus, selective oxidation of silicon and the modifying agent will occur, and the silicide coating will not tend to reduce the oxide layer. Modifying agents can be introduced into the coating by the pack cementation process. Using sources containing the modifier at controlled chemical potentials allows control of the coating composition. Partially substituting aluminum for silicon in TaSi2 coatings by forming a Ta(Si,Al)2 solid solution was effective in moderately increasing the oxidation protection.

Jan 1, 1968

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to begin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTURES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, depending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1951

By AIME AIME

DURING my senior year at college a professor said to his class that a student who failed to obtain a passing grade in that certain subject could not graduate with his class and that his diploma would be withheld until the failure had been removed. In that way for four years a diploma had been made to appear to us as the objective in attending college. We grew up to think that a diploma was the means of providing employment; consequently, a diploma could not be jeopardized and, heeding the professor's remarks, we resolved to put forth special efforts and make good. During one of our class periods this same professor digressed briefly from his prepared lecture in metallurgy and advised the boys to join a national technical society. He spoke with earnestness and sincerity. After class we students discussed those remarks. We concluded that the professor had not convinced us. We were already members of technical societies at school and saw no need of joining another. In fact, even up to that moment a society had never indicated to any of us that joining it had any relation to landing a job, and we were fully aware that joining another society meant paying out more money, for fees and dues, which money we then needed to buy food, clothes, and perhaps a new slide rule. Furthermore, we knew that joining a society was not part of the curriculum and, therefore, the diploma could not be withheld if we did not follow the advice. Our conclusion was that we would not join but would concentrate on our work that assured getting our diplomas.

Jan 1, 1936

By W. N. Miner, R. O. Elliott

Electrical-resistivity )measurments were made be-trueetz room temperatrive and 1.5 oK on five different stocks of cerium metal, and the results were correlated with the types, amounts, and distribution of the impurities present. Magnesium, which appeared to be distributed as a solute throughout the cerium matrix, was found to have a large effect on the residual resistivity, 1 at. pct Mg being sufficient to increase the residual resistivity by about 10 microhm-cm. The formation of ß by repeated thermal cycling between room temperature and liquid-helium temperature is attributed to the deformation and faulting that occurs during the ? D a transformation. In preparation for starting a proposed study of cerium-rich alloys, we examined samples from severa1 stocks of cerium metal in order to choose the purest stock for future use in making the alloys. Low-temperature electrical-resistivity data were used to gain initial information about the purities of the stocks. Additional information was subsequently obtained from chemical analyses, density measurements, optical metallography, and electron-micro-probe analyses. Cerium that has been annealed at high temperature and cooled to room temperature has the fee crystal structure (? phase) with a = 5.16Å. When cooled further, in the region between about 250" and 150°K, some of the fee phase transforms to the double hcp form (ß phase) with a = 3.68 and c = 11.92Å. The remainder of the room-temperature fee form (and perhaps some of the hexagonal phase) transforms electronically in the vicinity of 100° K to the more dense or "collapsed" fee form (a phase), a - 4.85A, by transferring about 0.5 electron per atom from the 4f level to the valence band. Very little work related specifically to the effects of impurities on the physical properties of cerium has been reported in the literature. Gaume-Mahn1, 2 has studied the effects of calcium, magnesium. iron, silicon, and tantalum on the electrical resistivity and magnetic susceptibility of cerium between 60o and 300°K. Gschneidner, Elliott, and McDonald3 have discussed the effects of total impurity content on the hysteresis of the a —? (reversible) transformation and on the formation of the 4 and "a-? intermediate" phases. Smith and Morrice* have reported the effect of total impurity content on the resistivity of cerium at 4 and 293°K. In none of these reports, however, is it apparent that the distributions of the impurities were determined, L.r., whether the impurities were present in inclusions or in solid solution in the matrix is not mentioned; nor does it appear that the phase purity of the cerium was always considered. In the present study, five different stocks of cerium were involved. One was represented by a single sample of electrowon cerium, which was all that had remained from a stock of high-purity material obtained from the U.S. Bureau of Mines, Reno, Nev., in 1959. The other four stocks were recently purchased from commercial sources and were specified to be 99.9 wt pct pure. EXPERIMENTAL Cerium stocks designated as #1, #2, #4, and #5 were obtained from commercial suppliers for the specific purpose of finding a reliable source of high-purity cerium. Although the purity level of the cerium was specified to be 99.9 pet, the specifications did not include limits as to the amounts of various impurities that would be acceptable. Consequently the chemical analyses of the different stocks varied widely. Stock #3, which had been obtained from the U.S. Bureau of Mines and which was the purest on the basis of chemical analyses, consisted of a single specimen of electrowon cerium. It was included in the examination for purposes of comparison. Table I contains the chemical and spectrographic-

Jan 1, 1968

By Arthur Zentner

The electrolytic zinc plant of today is foreshadowed in the patents issued to Léon Létrange of Paris in 1881 and 1883l. He proposed roasting zinc blende to make the zinc soluble in water or sulphuric acid, thus obtaining a sulphate solution. His purification was apparently that used in the lithopone work of the day. For electrolyzing he proposed anodes of carbon or lead, for cathodes zinc, copper or brass. Numerous patents by other workers were taken out in the first 10 years, most of which dealt with sulphate solutions. It is easy to presume that the formation of chlorine gas in zinc chloride electrolysis caused early emphasis on sulphate work. Lack of success with this invited further work with chloride solutions. Efficient and cheaper oxidizing agents for use in the chloride processes were more generally available. Carbon anodes could be used instead of lead anodes, which were blamed for much of the early electrolyzing troubles and remained in disfavor for many years. Carl Hoepfner received his first zinc patents in 18902. He was the most persistent of those who worked with chloride solutions and met with the largest measure of success. Hc built three plants, only one of which remained in operation. This was built in 1896 at the plant of Brunner, Mond & Co., Winnington, England, now part of Imperial Chemical Industries Ltd. It leached with by-product calcium chloride from the company's Solvay alkali plant and returned to it the chlorine formed in electrolyzing. The zinc plant had a capacity of 5 long tons of zinc, said to have been doubled later, and remained in operation until 1924. No commercial plant using chloride solutions has operated since then. E. A. Ashcroft experimented in the middle nineties with chloride, alkaline and sulphate solutions on materials from Broken Hill, Australia. He built a plant with a rated capacity of 10 long tons of zinc per day, at Cockle Creek, New South Wales, in 1898. This figure was never approached nor was cyclical operation achieved. The work in the plant appears to have been largely with sulphate solutions. The plant suffered from a multitude of troubles: poor roasting, gclatinous silica, liberal use of live steam in solutions to combat the gclatinous silica with considerable

Jan 1, 1937

By Arthur Notman

SacRamento Hill is a mass of granite porphyry intruded along a fault between Paleozoic sediments and pre-Cambrian schists in the Bisbee district, Cochise County, Arizona. The intrusion invaded both walls of the fault to a large extent, and the accompanying extensive mineralization of the Paleozoic limestones is the locus of the great high-grade copper orebodies of the Bisbee mines. Prior to 1909, although the presence of ore in the masa of the hill itself had long been suspected, systematic exploration had not been attempted. A few shallow pits on the surface here and there had disclosed some chal-cocite with associated carbonates as stringers in a mass of strongly brccciated, silicified, and iron-stained porphyry. The workings in the surrounding limestones had penetrated the porphyry in a dozen or SO places for some distance from the contact but had disclosed no ore. However, the rock had been largely altered to quartz and sericite and very thoroughly impregnated with pyrite and traces of the copper sulphides. A close geological study of the conditions, both surface and underground, strengthened these suspicions, and plans for prospecting the hill were made in 1909. Reference to the accompanying illustrations, Figs. 1 and 2, will give an idea of the general appearance of the surface. The mineralization is more intense in two main zones, one at the west end and the other at the east end of the hill. The outcrop of the hill is elliptical and approximately 3,000 ft. long by 1,400 ft. wide. The Sacramento shaft, which is the main hoisting shaft of the mine and situated at the east end of the hill, as shown by the accompanying map (Fig. 3), offered a convenient base for prospecting that end of the hill, while the workings from the Holbrook shaft offered a similar opportunity at the west end. The choice of level for the first work was determined by analogy with the most favorable depth for enrichment below surface obscrved in the other disseminated deposits of the Southwest.

Jan 1, 1916

By B. Chalmers, L. Bäckerud

The growth temperature of dendrite tips has been measured in a binary alloy system, Al-Cu, as a function of rate of formation of solid phase. Metallographic examination has rerealed the dendritic structure dereloped during different stages of the freezing process and factors influencing the undercooling, such as solute buildup, surface tension, and kinetic effects, have been estimated. Practical implications of the results are discussed. THE development of a dendritic growth pattern during the solidification of metals and alloys has an influence at least equal to that of grain size on the properties of the casting or ingot being produced. and consequently much interest has been devoted to the study of this phenomenon. A review of the knowledge gathered up to 1964 has been given by Chalmers.' Among recent publications in the area the works of Jackson et al 2 and Flemings and his coworkers3,4 are of special interest. This work is an experimental study of the factors which influence the development of a dendritic pattern during the solidification of a typical binary alloy system, A1-Cu, when there is no heat source in the liquid. This means that the temperature and the temperature gradient are controlled by the heat extraction from and latent heat evolved by the growing crystals. EXPERIMENTAL PROCEDURE Samples were prepared from a master alloy made up of aluminum, 99.995 pct, and copper. 99.99 pct, of the concentrations given below and of sufficient size to fill cylindrical graphite molds of 35 mm ID and 35 mm height. Bottom. wall. and lid of the graphite molds were all of 6 mm thickness, Fig. 1. Thin ceramic thermocouple shields could be introduced at different positions in the sample through holes in the lid. The assembly was heated in a small vertical resistance furnace to a suitable temperature. 700° to 720°C. which is well above the melting point of the sample. It was thereafter taken out of the furnace and chilled at selected rates, and the temperature changes in the sample were recorded. For high sensitivity in the temperature recordings, a reference thermocouple was held in a solidifying pure aluminum melt. which was very well insulated and therefore was at a constant temperature. 660°C, for nearly half an hour. The thermocouples were connected so that the difference voltage was fed into the recorder of which the most sensitive range was 1 mV. Temperature variations could be read to within 0.l°C. The thermocouples used were of the Chromel-Alumel type (28- or 38-gage wires) and the recorder a two-pen Moseley strip chart recorder. The different rates of chilling were obtained in the following way. a) The graphite crucible was wrapped in one or two layers of an insulating. feltlike material (Fiberfrax paper from the Carborundum Co.). The drop in temperature per unit time after complete solidification could thereby be varied from 8" to 18°C per min. This corresponds to a rate of heat extraction in the given samples from 0.08 to 0.17 cal cm-' sec-I. 6) The bare graphite mold was placed free on a piece of firebrick. The measured temperature drop was around 50°C per min (-0.5 cal cm-" ' sec- I). c) By blowing compressed air through a tube with many holes surrounding the mold in a ring shape. the rate of heat transfer could be raised to 150' to 200°C per min (-1.7 cal cm-3 sec- I). d) Cooling rates around 1000 C per mill (-9.4 cal cm-3 sec-l) were obtained by substituting the air in the device used in c by water. The range of cooling rates used in these experiments correspond to technical casting processes from slow solidification as obtained in sand molds to very rapid freezing which occurs in some continuous casting and welding processes. EXPERIMENTAL RESULTS The A1-Cu system was chosen for the experiments: the relevant part of the phase diagram is reproduced in Fig. 2. Observation of the Center Temperature. When a thermocouple is inserted in the center of the melt. the type of cooling curves obtained at slow solidification rates differs little from numerous published curves from similar systems. and the solidification pattern

Jan 1, 1970

We did install one 100% brick bottom in our #33 furnace which is basically the same design as Inland's furnace. We had previously embarked on a program of replacing all bottoms in our 300 ton furnaces every 2nd campaign which would be about every 2000 - 2300 heats. This had been necessitated by the effect of our rather high oxygen blowing rates and our desire to maintain a minimum bottom interval level. This meant that we were able to compare bottom performance of various types of materials on a realistic bas is. Since furnace availability is critical to our operation, we are organized to employ every piece of equipment and all the necessary man power to complete a rebuild in the shortest possible time. A 300 ton furnace requires 7.5 days to rebuild. If a new bottom is to be installed an additional 2.5 days is added - 24 hours for tear out and 36 hours for bricklaying - making a total of 10 days.

Jan 1, 1972

By H. D. Newell

THERE has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-tem-perature steels" are meant those specifically designed for service at ele-vated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service.

Jan 1, 1937

By S. J. Rothman, L. T. Lloyd

S. J. Rothman and L. T. Lloyd (Argonne National Laboratory)— Hagel's paperz0 discusses the question of the mechanism for self-diffusion in bcc transition metals. Recent work21"23 has led us to agree with him in reabandoning the ring mechanism in favor of a defect mechanism, most likely vacancies. On the other hand, we think that Hagel's attempt to group together all self-diffusion in bcc transition metals is wrong. We prefer the scheme of Peart, Graham, and omlin," who separate them into two groups. One group contains the anomalously behaved metals P titanium,', y uranium, and perhaps zirconim.' The other group contains a iron," this alloy was held at 1800°C for 2 hr before quenching, its structure was all a. B. C. Giessen, I. Rump, and N. J. Grant (Authors' reply)—We very much appreciate the discussion by Deardorff and Kato regarding the a to /3 transformation temperature of hafnium. In the W-Hf program, as well as in a current study of the system Cr-Hf, standard precautions were exercised against contamination, including vacua of less than 10"5 mm Hg and a weight control check of all specimens to insure an impurity rise of less than 100 ppm. Following receipt of the above discussion, a revision was made in the annealing process. Arc-cast specimens were etched with a 10 pct HF-90 pct HNO solution until 1 mm of surface, including a possible oxide film, was removed. Annealing was done in a hafnium container which provided a long diffusion path for gaseous contaminants. Finally, the heat treating time was shortened. Structural changes were noted to occur quite slowly. A 99.5 at. pct Hf alloy showed 70 pct /3 after 30 min at 1700°C and was 100 pct /3 after 10 min at 1715°C. After 24 hr at 1740C, the alloy was found to be 10 pct/3. This change is due to contamination; it was estimated that it corresponds to an increase of 60°C in the transformation temperature over a 24 hr period. The corresponding change in 30 rnin would be slight. Using the same hafnium as in the above publication, and three new alloys at 98, 99, and 99.5 at. pct Hf, the transformation temperature was indicated to be 1715" 15°C. Since this hafnium contained 4.4 at. pct Zr, a correction of 40 5C, based on an assumed approximately linear transformation temperature curve, must be made for pure hafnium. This yields a value of 1755 20°C in good agreement with Deardorff and Kato's value. Because the slope of the boundary is small, this permits a good extrapolation, and we regard the W-Hf alloys as well suited to check the Hf transformation temperature. niobirn,'' and molybdenum,22 whose activation energies correlate with the melting temperature and whose Do values follow Zener's predictions.28 We have no quarrel with Hagel's placing chromium into the second group; we disagree with his interpreting our data to make uranium fit into that group. Hagel considers that the measurements of self-diffusion in uranium below about 950°C represent combined volume and grain boundary diffusion. This contention is based on the curvature of the penetration plot for our 891°C run,4 which also has a nearly straight line plot of log c vs x. Hagel has extrapolated these characteristics to our 803.5C run and fitted his Arrhenius plot for self-diffusion in y uranium to our four highest temperature points only. We think this is wrong for the following reasons.

Jan 1, 1963

US 4,135,913-Extraction of nickel values from iron-containing nickel sulfide ore, particularly pentlandite or nickeliferous pyrrhotite A mixture of raw ore, roasted ore, or iron powder, and coal as a reductant is heated to a temperature of 800- 1000° C in a nonoxidizing atmosphere to convert the bulk of the iron content to metallic iron while diffusing into the iron the bulk of the nickel, the mixture cooled, and the cool material separated into a magnetic fraction containing most of the nickel and a non-magnetic gangue fraction A Illis arid L S Renzoni, assigned to International Nickel Co, Inc Jan 23, 1979 7 pp (75-21) Filed 10-10-75 (621,343) Priority Canada, 10-27-72 (155,032) Same Canadian 981,910, dated Jan 20, 1976 Same British 1,389,145, dated Apr 3, 1975 US 4,135,917-In the recovery of gallium from a solution obtained by the digestion of bauxite or nepheline in an alkali solution for the production of alumina, the digestion solution is neutralized, the neutralized solution evaporated to an op¬timum caustic alkali concentration and adjusted to a ratio of alkali metal oxide to alumina of above 2, the corrected solu¬tion contacted with a gallium-aluminum alloy, arid high-purity gallium recovered from the solution by electrolysis or cemen¬tation K A Badaliants, et al Jan 23, 1979 6 pp (75-109) Filed 12-19-77 (862,201) Priority USSR, 12-22-76 (2,428,¬006) US 4,135,918-Extraction of copper from copper sulfide ore containing also one or more of the metals iron, nickel, arid cobalt Ore is roasted at a temperature of 750-800° C to expel sulfur, the sulfur-free calcine slurried in water containing a sufficient amount of sulfuric acid to supplement any sulfuric acid formed in situ, the slurry heated at 150-165° C in the presence of a reducing gas to form soluble sulfates of metals other than copper while reducing copper to elemental form, arid the slurry filtered to recover copper solids Any precious metals present in the ore will report with the copper solids V A Ettel, A P Devuyst, R Sridhar, arid C. E O'Neill, as¬signed to International Nickel Co, Inc Jan 23, 1979 5 pp (75-117) Filed 3-2-78 (882,610) Priority Canada, 5-13-77 (278,360)

Jan 1, 1980

By Martin T. Broome

INTRODUCTION The Luanshya Mine is situated in the southern part of the Zambian Copperbelt. The copper ore deposit is stratiform, and is preserved in a synclinorium known as the Roan/ Muliashi basin. Roan shaft (formally called No.14 shaft) is located at the eastern end of the syncline and is theoldest of the presently operating hoisting shafts, being sunk during the 1930's. It presently hoists some 45 per- cent of the total Luanshya Mine production. A cross-section through the shaft is shown in figure 1. The ore formation on the south limb is unmined on this section because until recently it was believed that such mining might cause damage to the shaft. This paper examines the influences of adjacent mining on this so-called 'shaft pillar', and describes the mechanics of subsidence of the pillar itself. GEOLOGY AND STRUCTURE Figure 1 shows the general form of folding in the vicinity of Roan shaft. The north and south limbs of the main syncline approach parallelism, with the bottom of the trough fairly smoothly rounded. The axis of the - trough plunges to the west-north-west at 6° - l0°. A brief summary of the major lithologies present in the Roan basin is given in table 1, however, the performance of the overall structure during progressive mining of the ore horizon is controlled by the following features in addition to the mining method. Intraformational Contacts These are characteristically weak in most geological environments. The BC/RL7 contact is an unconformity between moderately weak quartz-biotite schists below (unconfined compressive strength 40 - 80 MN/M 2), and strong quartzites above (U .C .S. 170-200 MN/M2) Subsequent formations are conformable, and planes of weakness are generally the result of contrasting lithology (see below). Weak Interbeds The Rt7, RL6, RL5, RL3 and RU2 horizons consist predominantly of quartzitic rocks, i.e. conglomerates, quartzites and argillites, and as such are generally strong and considered suitable for the positioning of development. Between these however, lie two much weaker dolomitic horizons, the RL4 and RU1. The Rt4 is the main hangingwall aquifer, and must be drained prior to mining. Drainage results in an extremely weak, blocky cavernous horizon which usually requires support if exposed by development. Similarly, the RU1 formation is comprised mainly of dolomites and dolomitic arqillites which are weak and cavernous. In the eastern part of the Roan/

Jan 1, 1981

By B. C. Allen

Liquid surface tensions of copper and 18 Group IV-A to VIII transition metals (Ti, Zr, Hf, V, Cb, Ta, Mo, W, Re, Ru, Rh, Pd, Os, Ir, Pt, Fe, Ni. Co) have been measured by the static pendant-drop and dynamic drop-weight methods on the same rod sample. The drops were formed by electron-bombardment heating in high vacuum. Application of necessary corrections enabled determination of surface tensions to k2 pct and agreement between methods to * 1 to 4 pct for all the metals studied. Evidence is presented that the liquid surface was well screened by metal vapor, suggesting negligible adsorption of gaseous impurities and that the surface tensions measured are characteristic of the metals involved. Correlations between liquid surface tension and melting point, molar volume, heat of vaporization, and atomic number are presented and discussed. Temperature coefficients of surface tension were calculated using Eötvös' law. SURFACE tension and interface energies of metals are the result of incomplete atomic coordination resulting in a force perpendicular to the boundary, tending to minimize its area. These energies are important in many phases of metallurgy, including microstructure, sintering, joining, electronic emission, and lubrication, which in turn affect many physical and mechanical properties of metals. Liquid surface tension refers to the interface between the liquid and its own vapor or nonreactive atmosphere, and is considered a physical property of the liquid. Since equilibrium shapes can be readily obtained with liquids, the units of surface tension (force per length) and interface energy (energy per area) are interchangeable. Thermo-dynamically, the surface tension ?LV is given by the change in free energy F with surface area A at constant pressure P, temperature T, and composition N: for commercially important refractory metals, vanadium, columbium, tantalum,13,14 molybdenum,14 and tungsten,l5 and none for the rare platinum-group metals and rhenium. Measuring the surface tensions of transition metals is difficult because of their high reactivity and melting points. Of the many techniques available,16-18 the pendant-drop 19-21 and drop-weight methods17,22 are considered superior because they can be modified to eliminate persistent sources of contamination such as supports and capillaries necessary in the popular sessile drop, capillary rise, and maximum-bubble-pressure techniques. The necessary modification is to melt a drop on the tip of a vertical rod, which provides support through a solid of the same composition.13,15 The object of the work was to study the surface-tension behavior of copper and transition metals, having reasonably low vapor pressures. Liquid surface tension of each pure metal was systematically determined by using a combination of the static pendant-drop and dynamic drop-weight methods on the same rod. Liquid drops were formed by electron-bombardment heating in high vacuum. EXPERIMENTAL WORK As indicated in Table I, the metals studied were high purity and generally were obtained in rod form. The exceptions were titanium and zirconium, which were machined from crystal bars, and molybdenum (tot 11, osmium, and ruthenium, which were sintered and arc cast into rods. All the metals were ground or swaged to desired sizes between 1- and 7-mm diam, and centerless ground round and smooth to a finish better than 50 µ in., rms. Each rod was thoroughly cleaned with steel wool, degreased, acid etched, and dried. In a typical run, the rod was vertically clamped in a modified floating-zone electron-bombardment furnace designed after Calverley23 and Carlson.24 The specimen was outgassed and maintained positive at several kilovolts in a dynamic vacuum of 10-5 to 10-7 mm. The bottom end was enclosed by a tantalum pillbox and heated by electrons emitted from a hot concentric tungsten filament mounted on a movable bracket. The bombardment power was slowly raised until melting was observed. Power requirements ranged from 30 w for copper to 1300 w for 4-mm tungsten. The stabilized and out-gassed drop of near-maximum size was photographed at 4. 1X on panchromatic film at desired time inter-

Jan 1, 1963

By I. S. Servi, N. F. Graves

THE etch-pit technique has long been used to reveal low-angle boundaries and, in general, the distribution of dislocations in high-purity metals. Often this technique is amenable to quantitative computations,' but generally is affected by some degree of uncertainty because etch pits can be nucleated not only by dislocations, but also by inclusions and surface imperfections. In the case of high-purity zinc, Gilman' reported that etch pits were produced only after adding 0.1 atomic per cent of cadmium to the crystals and aging at a proper temperature. In the course of a study of low-angle boundary behavior in zinc crystals, etch pits were produced in 99.999 pct zinc without resorting to intentional contamination, by etching in a 50:50 HNO3H2O solution. The technique consists of etching until the heat of reaction brings the solution to a boil, and in displacing the etchant rapidly with a stream of cold water, thus avoiding staining. The undesirable features of this technique are the heating effect and the removal of a considerable amount of material. A high polish is obtained if staining is controlled properly; therefore, the etch pits appear very clearly and with excellent contrast when observed under dark field illumination. This is especially helpful for cursory examinations at low magnifications. Several observations were made on zinc crystals of square cross section, having one face parallel to the basal plane and one edge parallel to a slip direction, Fig. l(a). When such a crystal was bent about 2" over a glass die and annealed at 390°C, a sharp boundary was formed only in the inner portion of the crystal. Near the two prismatic faces, perpendicular to the basal plane, the boundary was always branched into many lower-angle boundaries, Fig. 1(b). Attempts to move the main boundary by applying a shear stress to the specimen invariably resulted in curving the boundary, the branched ends remaining pinned in their original location, Fig. 1 (c). The prismatic face, when etched as indicated in the foregoing, revealed the existence of numerous (sometimes up to 30) fine boundaries, nearly parallel to each other. Pre-existing lineage boundaries, generally parallel to the direction of growth, were barriers to the formation of polygonization boundaries and interrupted the continuity of the substructure, Fig. 2. Twin

Jan 1, 1959

By AIME

THE wind howls almost incessantly over the mining engineers working in the near desert that is the Division of Namaqualand, the upper Atlantic coastal corner of South Africa's Cape of Good Hope Province. But when these men at the U. S.-owned mines called Nababeep South and East O'okiep (pronounced Oh-keep) tell you about their achievements, they can be heard above the wind. For their O'okiep Copper Co. Ltd. now produces over half the Union of South Africa's annual output of 30,000 tons of copper metal. Moreover, it is a very decent sample of U. S. geotechnical imagination. financial daring, and managerial skill, all operating successfully in a

Jan 1, 1947

By J. L. CAHUTHERS

MANY different methods are used for transporting coal from the working face to the tipple. The common methods are animal haulage, locomotive haulage, conveyor systems, and combinations of these three, supplemented, at times, by the miner pushing his own car. Haulage may also be classified into gathering and main line. Gathering haulage is the collecting of loaded cars to a point whence they are hauled to the tipple. In this there is perhaps more lost-time than on the main line because there are .more units in the operation to be synchronized. Also, conditions on the gathering haul- age, such as bad track, poor timbering, insufficient motive power, etc., cause delays; usually these are corrected on the main-line haulage.

Jan 1, 1931

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

PAST AND PRESENT CHAIRMEN OF DIVISIONS Institute of Metals Iron and Steel Mineral Industry Industrial Minerals Year Division Petroleum Division Division Coal Division Education Division Division 1918 W. M. CORSET 1919 " 1920 W. H. BASSETT 1921 " 1922 W. B. PRICE RALPH ARNOLD 1923 E. DEGOLYER 1924 G. B. ELLIOTT 1925 F. JULIUS FOHS 1926 P. D. MERICA 1927 11 JOHN. M. LOVEJOY 1928 S. SKOWRONSKI A. W. AMBROSE RALPH H. SWEETSER ' 1929 " J. B. UMPLEHY G. B. WATERHOUSE 1930 ZAY JEFFRIES C. V. MILLIKAN W. J. MACKENZIE HOWARD N. EAVENSON 1931 SAM TOUR C. E. BEECHER F. M. BECKET 1932 C. H. MATHEWSON EARL OLIVER F. N. SPELLER THOMAS G. FEAR C. H. FULTON 1933 T. S. FULLER W. E. WRATHER JOHN JOHNSTON ELI T. CONNOR " 1934 J. L. CHRISTIE H. D. WILDE, JR. L. F. REINARTZ " T. T. READ 1935 W. M. PEIRCE HARRY H. POWER A. B. KINZEL JOHN T. RYAN SAMUEL H. DOLBEAR 1936 E. H. DIX, JR. HALLAN N. MARSH C. E. WILLIAMS EUGENE MCAULIFFE WILLIAM B. PLANK OLIVER BOWLES 1937 A. J. PHILLIPS M. ALBERTSON FRANCIS B. FOLEY J. B. MORROW " CHESTER A. FULTON 1938 R. F. MEHL G. B. CORLESS J. T. MACKENZIE PAUL WEIR FRANCIS A.THOMSON J. R. THOENEN 1939 R. H. LEACH W. H. GETS J. HUNTER NEAD C. A. GIBBONS " M. M. LEIGHTON 1940 E. M. Wise T. V. MOORE F. T. SISCO C. E. LA WALL W. R. CHEDSEY W. M. WEIGEL 1941 D. K. CRAMPTON E. A. STEPHENSON C. H. HERTY, JR. JULIAN E. TOBEY " PAUL M. TYLER 1942 CARL E. SWARTZ HARRY P. STOLZ E. C. SMITH NEWELL G. ALFORD A. F. GREAVES-WALKER B. L. MILLER

Jan 1, 1942