Search Documents

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground mine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.9 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated.

Jan 1, 1940

By Hal W. Hunt

Steel and concrete piles and power-actuated hammers have developed almost entirely within the past 100 years. Prior to that time, piles were mostly timber, driven with a drop hammer or a maul. The Engineering News Formula ? for timber piles driven with a drop hammer at a factor of safety of six ? was promulgated by Wellington in 1888. Steel com­panies supplied fabricated and rolled shapes for piles in the early 1900's. The thin shell and then uncased concrete piles originated about that time. Now leads have become sophisticated to accurately spot a pile at any required batter. Hammers have grown to phenomenal size and vibratories are being accepted at full value.

Jan 1, 1984

This paper pays tribute to the pioneers in geomechanics, and addresses some of the most pressing issues of our time related to deep mining, and how to mitigate these issues. Solutions developed by our predecessors seem to have reached their limits as mines continue to go deeper. The International Society for Rock Mechanics (ISRM) guidelines for rock mass characterization for excavation design also require re-thinking to reflect current knowledge and experience. Thus, a whole new approach is urgently required to increase mine safety and productivity. The paper will draw on the challenges and experiences in medicine and science that have been overcome through genuine collaboration, advances in technology, and impressive funding, which can be adopted to provide solutions to contemporary geomechanics challenges for increased safety and productivity as mines continue to go deeper.

Jan 1, 2014

By Ray Brainard

Charleston Water System?s Daniel Island Extension Tunnel, initially thought to be the simplest of the four replacement tunnels to design and build, became the most challenging after the discovery of an unexpected 30-ft thick lens of sand in the normally consistent Cooper Marl while sinking a shaft on Daniel Island. This paper will explore the challenges involved with determining the extent of the unforeseen lens of sand, the accelerated boring program, and the redesign of the vertical alignment?keeping the alignment between the sand layer and the bottom of the Cooper River. It will describe how the challenges were overcome, and how the Owner, Engineer, and Contractor were able to team together to achieve the desired results.

By S. Kwon

When an underground excavation is created near to an instrumented measuring location, deformation at the location increases. The characteristics of this deformation increase, as well as the duration of the influence caused by the adjacent excavation, is dependent on parameters such as opening geometry and measuring location. In this study, neural networks were applied to investigate the deformation increase and the influence of each parameter on the deformation change derived from extensometer measurements at the Waste Isolation Pilot Plant (WIPP) site in New Mexico, USA.

Jan 1, 1998

By Craig Compton

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers? compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

Jan 1, 2007

By R. T. Langland

Using a finite-element computer model, we have conducted an analytical study of roof behavior in a room-and-pillar coal mine. With standard engineering property in formation and a computer code developed for the Bureau of Mines to calculate roof sag, convergence, and roof-bolt load change, we have calculated the stability of roof-support systems and compared the computed data with experimental data collected during a field investigation at three test sites, one in a development area and two in production areas of a coal mine.

Jan 1, 1978

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By William G. Pariseau

The research reported here concerns a four year study of the rock mechanics aspects of two underground hardrock mine study stopes. The first study was conducted at Anaconda Minerals Company's Carr Fork Mine near Tooele, Utah. The second study was conducted at the Homestake Mining Company's Homestake Mine In Lead, South Dakota. Both case studies were cooperative efforts of mining company personnel, the Spokane Research Center of the Bureau of Mines and the Department of Mining Engineering, University of Utah. Large diameter (6 1/2 In.) blastholes were an integral part of the stoplng method at each mine. A true vertical crater retreat (VCR) method was used at the Homestake Mine, while a vertical bench mining method (VBM) was used at the Carr Fork Mine. VCR and VBM methods were developed In the 1970's; they offer significant productivity gain and are now used throughout the world. The new technology, however, brings with It a requirement for more sophisticated engineering design and control. Since there are no personnel in a VCR or VBM stope, all ground control Including dimensioning of stopes and pillars and the layout of cable bolt assays or other artificial support must be done in advance of production blasting. Accordingly, the objective of the research study was the establishment of a procedure for optimizing stops and pillar sizes. The approach taken was In each case a combination of mine measurements of the study stope response to mining, laboratory testing for rock properties and In situ stress measurements of the premining stress field, and theoretical calculations of the study stope response to mining. All calculations were done with the UTAH-II finite element computer program. Simulation of the blasting sequence gave a correlation of 0.88 between measured and calculated extensometer readings (Incremental relative displacements) at the Carr Fork Mine where other 30 Instrumentation boreholes were used to monitor the test stope response. A correlation of 0.84 was obtained at the Homestake Mine where 19 instrumented boreholes were used for monitoring purposes. These high correlations validated the computer mode and calibrated It for rock mass properties. The calibrated model was then used In parametric studies of alternative design layouts.

Jan 1, 1985

By John Russell

"Faster, safer, grinding mill relining offers the obvious attractions of reduced mill relining times with the knock-on incentive to reduce all other maintenance down-time, opening the possibility for increased annual plant utilisation.Leading edge liner handler technologies by RME, focused toward even shorter relines for very large SAG and AG mills, have recently split into two quite distinct paths:•,?Single SAG/AG Mill Relining Machines (MRM’s) of very large capacity, such as Newcrest Cadia’s 40’ SAG MRM of 6000 kg capacity and P.T. Freeport’s 38’/34’ SAG MRM of 7250 kg capacity;•,?Twin-machine SAG/AG Mill Relining Systems of moderate to large capacity such as BHP Billiton’s Escondida Laguna Seca 38’ SAG MRM’s, each featuring 4500 kg capacity.RME, its customers noted above and their liner suppliers are providing leadership in this important annual utilisation advance.Once the 24 hour mill shell reline becomes reality, liners designed for maximum profit, not maximum life, albeit exchanged more frequently, become possible too.INTRODUCTIONAt most mineral grinding plants, mill relining activities dictate each maintenance shutdown’s critical path. When annualized, mill relining remains the largest, single influence in defining plant availability.Because of restricted access, both inside and outside the mill, increased application of manual labour has no effect on reducing relining downtime. The only answer for RME has been to develop and apply new relining technologies now known as RME’s Mill Relining System.RME’s primary focus for over twenty years has been the reduction of grinding mill relining times while simultaneously providing a marked improvement in relining safety. Our original (1990) target was to halve traditional (pre-RME) reline times and to eliminate accidents and injury by mechanizing all physical work."

Jan 1, 2008

By C. M. St. John

A series of analyses of possible mining excavations associated with the development of copper nickel deposits of the MINNAMAX site in Northeastern Minnesota is presented. Specific areas such as roof and pillar stability and excavution orientations are addressed. The majority of these analyses were conducted using a boundary element method but some cases were also analyzed using the finite element method. Comparable results were obtained using the two methods but the boundary element method required less data preparation time and computer run time. Results of the analyses, as well as indicating the capabilities of geotechnical numerical models, provide some insights into behavior around multiple excavations in jointed rock.

Jan 1, 1979

LANDSAT imagery has renewed interest in linear features first recognised by E. S. Hills in a physiographic model of Australia. Certain of these lineaments are aligned with structures which control mineralisation.Lineament guidelines are potentially useful in many poorlyexposed areas if they can be recognised early enough in exploration and drilling programs leading to mine development.A case history based on the Charters Towers Gold Field indicates that lineament guidelines can be established early enough to guide development ofnew mines. The position of the Charters Towers Lineament was known as early as 1956. Subsequently, more detailed publications identified and classified associated lineaments which provide intersections correlated with gold occurrences. The discovery of a significant orebody at one of the most prominent lineament intersections came in 1975. Mine drilling has confirmed the influence ofintersecting structural trends indicated by lineaments but not by previous regional mapping.Recent gold discoveries south of Charters Towers lie in a grid of prominent lineaments. The development of mines about Charters Towers will provide additional understanding of relationships between centres of mineralisation and lineament intersections. This understanding may in future be sufficient to encourage exploration for a new generation of concealed gold deposits in northeastern Queensland.

Jan 1, 1986

Development of a Froth Dropback Measurement Device

Sep 13, 2010

By Ö. Uysal

This study deals with the presentation of the mechanized longwall mining project introduced some years ago to increase productivity and output of Aegean Lignite Establishment (ELI) owned by Turkish Coal Enterprises (TKI.) and the comparison of this method with a planned alternative new mining method called ?shortwall mining? where continuous miners will be introduced as primary coal excavation machines. Following the planning phase, production costs have been calculated for both mining methods on the basis of a panel having a height of 7.5 m. In addition to cost analysis, both methods have been evaluated using ?the multi-dimensional objective system?. In this evaluation the value synthesis has been carried out according to scoring models. Lastly, the advantages and disadvantages of both production methods have been stated by analysing them according to related criteria. In the light of outputs gathered from the analyses, it has been determined that the shortwall mining method will out perform the longwall method. Keywords: continuous miner, shortwall mining, longwall mining, multi-dimensional objective system.

Jan 1, 2006

By Richard Peaker, Jens Lichter, Alexander V. Potapov

The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism. This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.

Jan 1, 2007

By Nino Catalano

The combination of two top levels of cross-lot braces designed and installed to act as a truss, and vertical post-tensioning of the panels allow the unbraced excavation of a 36' span. Philosophy of Excavation Support System The excavation of interest is for the cut-and-cover box sections of the southern approach to the Third Harbor Tunnel, which is part of the Central Artery/Tunnel project in Boston, Massachusetts. The 60' deep excavation is located very close to an existing building which is supported by piles, as shown in Figure 1. Therefore, it was necessary to minimize ground movement which may damage the building.

Jan 1, 1994

By Walter Frank

The purpose of the work covered by this contract is to develop a ground and pilot conductor connector which will significantly improve mine trailing cable splice performance. This work compliments the work completed under Contract 00357100 on the development of crimp connectors for the phase conductors of trailing cables. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. As with the phase development work, the ground and pilot connector work is essentially of an empirical nature. As a result time is devoted to explaining the derivations of the test procedures used. In order to familiarize the reader with connector terminology a section is devoted to a glossary of pertinent terms. The connector design effort includes connectors for splicing ground and pilot conductors. A distinction is made between connectors suitable for splicing round and flat ground configurations. The same also applies to the pilot conductors. During the course of this work, much time has been devoted to the question of suitability of round cable configurations for trailing cable applications. This is discussed in detail along with resulting conclusions and recommendations. A field test program was conducted in order to confirm ground and pilot connector laboratory data. This testing also determined the viability of the connector designs and recommended installation techniques in a mine environment.

Jan 1, 1979

By Stephen P. Quin

One of the most prospective undeveloped greenstone belts in Canada, the Hope Bay greenstone belt extends over 80km in a north-south direction and is between 7 and 20km wide. The belt lies on the arctic coast and comprises mafic meta-volcanic and meta-sedimentary rocks that are bounded by Archean granite intrusives and gneisses. The greenstone package has been deformed during multiple events and is transected by major northsouth trending shear zones that appear to exert a significant control on the localization of mineralization. The Hope Bay belt contains a number of significant gold deposits hosted in a typical Archean greenstone belt and which occur in several geologic settings, including shear-hosted, lode-style and breccia-associated. Combined, the deposits host a measured and indicated resource of 1.6 million oz of gold averaging 15.7 g/t plus an inferred resource of 2.7 million oz of gold averaging 12.3 g/t. All deposits remain open to expansion. Exploration in the period 2000-2002 by Miramar includes more than 110,000m of drilling to more fully define the nature of the known deposits, while regional exploration has focused on identifying and evaluating new targets. In carrying out its programs, Miramar uses a number of techniques to improve its chances of exploration success. Activity in 2003 includes 43,000m of drilling focused on expanding resources in the Madrid area, testing the Boston deposit at depth and continuing the hunt for more discoveries. Meanwhile Miramar is advancing one of the deposits towards a production decision, based on a low capital, high return development scenario.

May 1, 2003

[ ]

Jan 1, 1938