Search Documents

By Masahiro Sasaki, Wu Kepeng, Chang-Yong. Kang, Kohji Okada, Naohiro Igata, Kazuya Miyahara

"The damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys has been investigated. Particularly the effects of microstrucutre composed of the phases of a , a ' , y , and e on the damping capacity have been clarified. Various fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 mass % Mn and 50% cold rolling formed the largest volume fraction of e martensite and showed the highest damping capacity. The other phases of a, a' and y had very small effect on the increasing of damping capacity.IntroductionFe-Mn alloys are known to be one of the high damping capacity materials [l-3]. In the present research, the damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys, in which 12% Cr is added for the improvement of corrosion resistance of the Fe-Mn alloys, has been investigated. Particularly the effects of microstrucutre composed of various phases of a (bee), a ' (bet martensite), y (fee), and e (hcp martensite) on the damping capacity have been clarified. The results of preliminary research on Fe-Cr-Mn alloys are reported by Igata et al. [4] Various volume fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 % Mn and 50% cold rolling formed the largest fraction of e martensite and the measurement indicated clearly that e martensite had the largest effect on the damping capacity. The other phases of a ' y and a I had very small effect on the increasing of damping capacity."

Jan 1, 2000

By Debbie Marshall

Process water is an important consideration in the development of a nickel laterite project. Depending on the location of the ore body, sufficient fresh water may not be available and it may be necessary to use seawater (or saline groundwater) for ore preparation. This introduces various species, which have major effects on materials of construction and leaching chemistry. This paper summarizes batch testwork completed at the Falconbridge Technology Center. The leaching behaviour of eleven different laterite ore samples were compared using seawater and fresh water. For brevity, six of the eleven samples are reported here-the other five samples showed similar results. Each ore type was leached under identical conditions in both freshwater and seawater and the leaching chemistry compared. The batch test results were confirmed in a continuous pilot plant, and leach kinetics for the two systems were compared. Keywords: high pressure acid leaching, laterites

Jan 1, 2004

Electrocrystallization studies were conducted in a concentrated acid-copper electrolyte to determine the influence of chloride ions and glue on copper nucleation and on the structure of thin copper layers. Electrochemical experiments allied to SEM and XRD examination were performed to characterize the mechanism of nucleation in the presence of additives at 65°C. Results indicated that most of the copper nucleation from a 83 g dm-3 Cu2+ solution, with 140 g dm-3 of H2SO4 is achieved in a matter of milliseconds, Although the presence of chloride and glue, at the concentration levels tested, does not seem to substantially modify the nucleation mechanism, the morphology, nuclei density and the copper film structure and orientation are changed by the presence of additives and by electrolyte stirring.

Jan 1, 1999

By S. W. White

Plasma arc technology is increasingly being used to process a number of waste materials. In present research, plasma technology is being investigated to treat waste magnesium baghouse dust, which is a waste material from the Magnetherm process. This dust contains mostly MgO, but also contains NazO, CaO, and KzO. Plasma energy is to be used along with a reducing agent to produce pure gaseous magnesium while keeping the other materials in a slag. The magnesium will then be collected by rapid quenching. A non-transferred arc plasma torch is ideal for this reaction because of its high enthalpy and improved energy efficiency over conventional methods. Another advantage of plasma is that it allows for the pre-heating or pre-reacting of fine particles before contact with the melt. Thermodynamic calculations using the Gibb energy minimization method were used to determine the most stable compositions of the materials at various temperatures. Energy balances have also been calculated. These results conclude that we can recover approximately 98% of the magnesium with a proper quenching technique. The calculated results are compared with the experimental data, and good agreement between them was observed.

Jan 1, 1999

By Ullrich Kammer

Metaleurop's secondary lead smelter at Oker produces 60.000 mtpy of lead and lead alloys. More than 8O2 % of the raw materials are spent lead acid batteries. The other 2O2 % consists of drosses, ashes, scrap lead, type metal, sludges, etc., and is processed in a short rotary furnace (SRF). Also, industrial batteries not fitting in the battery scrap treatment plant are processed in the SRF provided with gas/oxygen-burner. Till Sept. 199O2, a soda ash slag was used in the SRF-smelting similar to the rotary kiln-smelting at Oker. Facing the future problems of handling and dumping soda ash slag, Harz-Metall GmbH has improved SRF-smelting with a non¬hazardous slag, insoluble in water, easy to dump and cheap in fluxes. This slag is based on a CaO-SiO2 -Fe0-type. Aim of the slag smelting is to be within the temperature range of 2 1100° and 1200°C - the eutectic line of Olivine in the corresponding ternary system. Since Sept. 199O2 Harz-Metall GmbH has operated the SRF with an "Olivine-type slag" with good results. Although the material is a "leady" slag. HMG is optimistic of using it as a filling material for construction purposes.

Jan 1, 1993

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

By Nobuhiro Ishikawa

The in-situ observation of the effect of impurities on the reduction process of iron oxides by C in TEM was carried out. A few wt% of CaO or AbO, was used as impurities in FeO was prepared. Some precipitates grew into the C layer expect for using 3.0wtCa. The reaction between FeO and carbon was much different from using pure FeO at about 800-1 lOOK. The rate of reaction became much slower including Ca and almost no reaction was happened with the concentration of CaO up to 3.0wt%. On the contrary, AbO, had ahuost no effect on the reaction. The results indicated that Ca suppressed the reaction and the effect of Al was much less. The precipitates which grew into C layer accompanied almost no Ca and AI. Only Fe was detected in the precipitates.

Jan 1, 2008

A simulation of a capper concentrate smelter was built with a capacity of 450,000 tons per year. The system's components to simulate were three : a Reverbetory furnace, a Wiente ' s modified converter ( TMC ) and two cranes. The system was classified as dynamic, stochastic and discrete. In the simulation language choice it was concluded that the most advantageous one was GPSS/H. The model verification was done through the interactive Debugger that the language has and the statistical validation was done through the result variables of sane activities, that as a whole characterize the system (charged matte and charged concentrate to the TMC, skimming white metal and skimning slag). The validation was done comparing the simulation results of these variables with the ones obtained for those variables in a specific month in the smelter. The comparison consisted in a difference of means test and in all cases the equality was accepted with a 95% of confidence. The animation tool was PROOF, a general purpose animator, that is used after processing the simulation.

Jan 1, 1994

By Y. Fautrelle, F. Felten, O. Metais, Y. Du Terrail

"We deal with the prediction of electromagnetically-driven turbulent flows by means of a Large-Eddy- Simulation method (LES). The model is applied in the case of a liquid metal pool submitted to a polyphase linear electromagnetic stirrer. We investigate two cases: (i) the frequency of the magnetic field is equal to 50 Hz; in that case the effects of the pulsating part of the Lorentz forces may be neglected; (ii) the frequency of the magnetic field is low (f= 1 Hz), then the oscillating part of the electromagnetic forces is taken into account. The LES predictions agree well with the mean velocity measurements, as does the standard k-a model. However, as for the turbulent kinetic energy predictions, there is a large discrepancy between the two models. When the oscillating part of the Lorentz forces is taken into account, the computations show that the fluid flow is sensitive to the unsteady part of the forces. We find that the mean velocity is not affected by the fluctuating component of the force. As for the turbulence parameters, the presence of the pulsating part leads to a significant reduction of the turbulent kinetic energy, whilst the turbulence length scale decreases.IntroductionElectromagnetic stirring is commonly used in various metallurgical processes. In continuous casting for example, it may improve the structure of the solidified metal products. Fluid flows generated by electromagnetic stirrers have been extensively investigated (1 ). As for numerical predictions, many works have been published on the subject. In most of the previous works, onepoint closure models have been used. The most used model is the well-known k-i:: model. Those models yield fairly good results as for the mean velocity prediction. However, it has two main drawbacks:(i) the turbulence is not predicted accurately,(ii) it is not well fitted for unstationary flows as well as transitional turbulent motions, where theReynolds number is moderate."

Jan 1, 1999

By F. Patisson

One of the major issues with multiparticle reactors is to handle their multiscale aspect. For modeling, it usually comes to coupling a reactor model (describing the phenomena at the macroscopic scale) with a so-called grain model (simulating the behavior of a single grain or a particle). An interesting approach proposed by H.Y. Sohn (1978) is to use the law of additive reaction times in order to calculate, approximately but analytically, the reaction rate of a particle in the reactor model. Its great advantage, compared to a numerical grain model, is to drastically reduce the computation time, particularly in the case of complex reactor models. This is the approach we retained for modeling the moving bed furnace, a counter-current gas-solid reactor used in the nuclear fuel-making route for producing uranium tetrafluoride from uranium trioxide. The numerical model we developed is 2-dimensional, steady-state and based on the finite volume method. It describes solid and gas flow, convective, conductive and radiative heat transfers, and six chemical reactions involved in the process. The law of additive reaction times is used to calculate analytically the rate of the three principal gas-solid reactions at every discrete point in the reactor. We have demonstrated the validity of this approach by comparing its results with those calculated from a numerical grain model. Also detailed in the paper are the main results of the moving bed furnace model itself and the possibilities of optimizing the process revealed by the calculations.

Jan 1, 2006

By Dan A. Mackie

Cyanide leaching operations have taken a beating from the press and the public at large for its seemingly haphazard approach to control of cyanide solutions and containment of tailings. Major spills in Colorado, Guyana, Spain, and more recently, Romania, have highlighted what had already been perceived to be a bad scene. Citizen initiatives and legislative actions are increasing. Whether these indictments are justified or not will not be debated in this paper. What this paper presents is that the technology to avoid these disasters and future ones has been around for more than ten years but has been ignored by the industry, despite demonstrated' cost effectiveness. It is time for miners to wakeup, and use emerging, instead of old, technologies.

Jan 1, 1998

By Gavin Beer

The Chelopech Copper/Gold Mine, located in west-central Bulgaria, has been in operation since 1953 producing a low-grade copper/gold concentrate containing up to six percent arsenic by weight. The penalties and restrictions imposed on smelting this concentrate, have seen the past operators of the mine strive to find a balance between achieving acceptable metal returns from the smelters and installing novel or unproven technologies in the face of changing political and economic climates. This paper documents the colourful history of the concentrate processing alternatives that have been investigated and implemented over the 45 year life of the Chelopech Mine, culminating in the high pressure oxidation option that is now the focus of a Definitive Feasibility Study (DFS) presently being undertaken by GRD Minproc Limited. The fundamental chemistry of the preceding alternatives is outlined followed by a discussion as to why each was ultimately not employed. A detailed description of the technology proposed in the DFS is given including: pressure oxidation, arsenic fixation, SX/EW copper recovery, CIL gold recovery and AVR/SART cyanide/copper recovery processes. Keywords: Arsenic, Scorodite, HPOX, Chelopech, Dundee

Jan 1, 2005

By E. Legault-Seguin

The current industrial practice in the processing of nickeliferous laterites involves the precipitation and releaching of Ni and Co to allow separation from the major impurities of Mn, Mg and Ca. A direct solvent extraction process has significant advantages over this practice, which suffers from difficult and costly precipitation steps, lower recovery and inherently complex flowsheets. The present investigation involves the examination of Cyanex 272, Cyanex 301 and Cyanex 302 as extractants for the direct extraction of Ni and Co from major impurities associated with laterite leaching, i.e. Mn, Mg and Ca. For Co extraction, Cyanex 301 and Cyanex 302 are superior to Cyanex 272, because they are able to selectively separate Co from Mn, Mg and Ca. Cyanex 272 offers complete extraction of Co from Ni and Ca, but Mn and Mg pose difficulty. Ni can only be extracted selectively with Cyanex 301, thus another extractant selective for Ni, such as Versatic 10 or Cyanex 301, is needed to recover Ni if Cyanex 302 or Cyanex 272 is used for the initial extraction.

Jan 1, 2004

By R. I. Rodriguez

Since the 1973 energy crisis, high fuel oil costs have been eroding the economics of the Nicaro and Punta Gorda Plants that employ the Caron Process for laterites processing. Since 1995, Cuban crude oil production has growth dramatically, with progressive utilization in power generation, cement and nickel plants. This paper shows how Nicaro and Punta Gorda plants have been able to shift from expensive Bunker C Fuel Oil to heavy but cheaper Cuban Crude Oil of high Sulfur content and achieve a significant reduction in operating cost. Problems related to the high sulfur content of the Cuban crude oil have demanded extensive investigations of the process chemistry and novelty solutions are proposed, with corresponding changes in process conditions. Innovative options are shown that will allow further cost reductions in the future. Keywords: Cuban Crude Oil, Sulfur, Ammonia.

Jan 1, 2004

By Haydar Güneş

In this study, a hydrometallurgical process was evaluated for the recovery of Nd from a Nd-Fe-B magnet. Each leaching test was performed at the solid (weight) to liquid (volume) ratio of 1:50 and was mixed at 400 rpm at ambient temperature. The effects of 3 different acids (HCl, HNO3, and H2SO4) on the extraction of Nd were investigated and H2SO4 was found to be more effective than other acid solutions. Under the optimal conditions, pregnant leach solution was produced with H2SO4 for subsequent Nd precipitation testing. Each precipitation test was carried out using 100 mL of feed solution mixed at 600 rpm at 25°C. NaOH and H2C2O4 were used for Nd precipitation. The highest Nd was precipitated as Nd2(C2O4)3, 10H2O with C2H2O4 at 20 min.

By Roland Kammel

In combination with various physical and chemical methods also electrochemical techniques are most frequently used to improve the recovery of metals from aqueous dilute process streams or effluents e.g. in electroplating, metal finishing, mining and metallurgical plants. To insure cathodic metal recoveries with favorable current efficiency and high throughputs per unit of cell volume seve¬ral types of electrolysis cells have been developed comprising extended electrode surface areas and/or intensive electrolyte. agitation. The practical experiences with these units indicate especially for the electrolytic recovery of metals whose values are high, that the treatment cost permits profitable operations with relativly short payback periods for the units. Anodic reactions can be utilized for the removal of undesired anion contents or buildups of impurities. Appropriate combinations of these recovery methods are used to improve the versatility and the overall economy. Industrial applications reveal their potentional as addidtive techniques for existing processes to reduce the metal content of effluents to values that meet the guide lines of environmental legislation whereas integrated in-operation recovery methods are nowadays increasingly introduced to approach nearly close-loop operations.

Jan 1, 1992

By T. Tamagawa

Vaporization of zinc and mixing of zinc vapor with CO-CO2 mixtures were studied experimentally to prepare Zn(g)-CO-CO2-Ar mixtures with desired composition for investigating the condensation behavior and efficiency of zinc vapor. The vaporization rate of zinc was generally constant under given conditions, and could be increased by raising the flow rate of the carrier gas, temperature and vaporization area. The Zn(g)-CO-CO,,-Ar mixtures were quenched by a water-cooling sampling tube for measuring the actual composition of the mixtures in the reactor. The oxidation extent of the zinc vapor in the CO-CO2 mixtures had relation to the CO2/CO ratios and the temperatures. Under current conditions, it was necessary to employ the CO2/CO ratio below 0.125 for mixing the zinc vapor with CO-CO2 mixtures without oxidation. In addition, the appearances and zinc contents of the condensed zinc on the sampling tube were also examined.

Jan 1, 2001

By Marco Olper

Zinc bearing materials containing chlorides and fluorides of alkali metals, such as EAF dust, Waelz oxides, galvanizing ashes, zinc & brass foundry fumes and converter fumes are little attractive, both technically and economically for processing in ISF plant or in a conventional zinc sulphate electrolysis works. The Ezinexm Process allows for the recovery of high purity zinc in cathode form, from these materials, regenerating the leaching liquor. The process is based on a new electrochemical system which depolarizes the anode reaction with reduction of the cell voltage, compared with the traditional sulphate electrolysis method. The electrolyte, based on a chloroamrnino complex, allows for the recovery of other valued metals present in the zinc bearing materials such as lead, copper and silver, these being recovered as a metallic cement consequently improving the economics of the process.

Jan 1, 1994

By Tatsuki Uzawa, Takashi Nagai

The consumption of Nd and Dy is increasing dramatically because of an exceptionally high demand for Nd-Fe-B-(Dy) magnets and a significant amount of the magnets are wasted. It is important to develop a recycle process the elements from the wasted magnets. In this study, Nd and Dy were extracted from the magnets by silver at high temperature. Nd can be extracted more than 70 % by silver. However, Dy is extracted only 25 % in the same experimental condition.

Jan 1, 2014

By Yousef Mohassab, Hong Yong Sohn, Mohamed Elzohiery

As part of the development of a novel flash ironmaking process at the University of Utah, a labscale flash reactor was used to produce iron directly from iron oxide concentrate. This work tested the feasibility of the novel flash ironmaking process using the partial combustion of hydrogen as fuel and reductant. In this flash reactor, the energy required to reduce concentrate particles was obtained from the internal combustion of hydrogen and oxygen with complementary energy from electrical resistance heating to compensate for the heat loss. After the reaction shaft was electrically pre-heated, hydrogen and oxygen streams produced a non-premixed flame inside the reaction shaft. Various conditions such as flame configuration, flame power, positions of concentrate feeding ports, excess hydrogen amount and residence time were tested. More than 90% reduction of magnetite or hematite was achieved at temperatures as low as 1175 oC with < 100% excess hydrogen in <10 s of residence time.

Jan 1, 2016