Search Documents

By Julio C. Martinez, Jeffrey L. Rice, Hayden Weschler

This paper details the extensive underpinning required to hold up the 39th street Bridge while demolishing its massive support piers and building a 30ft deep Cut/ Cover RR tunnel beneath it. The underpinning/SOE support required the construction of 16 large hand dug pits 36ft deep that were reinforced and concrete filled. In addition, an extensive steel support system was tied into the bridge super structure. All of the underpinning/tunnel construction was done while a 110ton crane sat directly atop the heavily trafficked – 66 ft. wide bridge. The tunnel excavation, concrete lining and final bridge pier support work will also be presented. All work was done within 5ft of active mainline tracks and that required tight grouting behind all lagging to eliminate any track settlement.

Jun 13, 2021

This paper presents the latest developments in the flotation model being developed collaboratively between the Julius Kruttschnitt Mineral Research Centre in Brisbane, Australia, and the Mineral Processing Research Unit of the University of Cape Town in South Africa as part of the Australian Minerals Industries Research Association (AMIRA) P9 Project. It includes: - characterisation of flotation cells using the bubble surface area flux, Sb; - relationship of Sb to the overall flotation rate constant; - determination of the froth recovery factor; - evaluation of ore floatability; - modelling of entrainment - development of the Floatability Characterisation Test Rig (FCTR); - use of the model in design and optimization of flotation plants; and - current and future work.

Jan 1, 1999

By Albert W. Deurbrouck

The coal reserves in the United States are estimated to be in excess of 300 billion recoverable tons, and current projections of energy requirements indicate our increased dependence upon these reserves. The Department of Energy's Energy Outlook for 1984 projects that coal consumption in the United States will increase from 737 million tons in 1983 to 958 million tons in 1990, and then to 1,110 million tons in 1995 (Table 1). As shown in this table, the future utilization of coal in the United States is closely tied to the electric utility market, a market that consumes about 85% of the coal produced. Be- cause of this dependence on the utility market, the uncertainties of new environmental regulations, particularly those concerning sulfur emissions, could have a significant adverse impact on future coal demands in the United States. SULFUR IN U.S. COALS Most of the Nation's coal reserves contain too much sulfur to be fired directly and meet existing emission control standards. In Table 2, the sulfur contents of the coals of the eastern United States are summarized by sulfur levels according to regions. While the coals of some of the eastern regions are predominantly high in sulfur content, it is important to recognize that large tonnages of coal with relatively lower sulfur content are available in these regions. Furthermore, an often significant portion of the sulfur occurs in the form of iron sulfide (Fes2 or pyrite). Because pyrite occurs as discrete particles of high specific gravity, it can often be removed by simple, inexpensive physical coal beneficiation techniques after being liberated by stage crushing. The potential for physical removal of pyrite by conventional specific gravity processes combined with stage crushing is summarized in Table 3 on a regional basis.

Jan 1, 1986

The Northside Storage Tunnel Project in Sydney includes over 20 km of TBM driven tunnels, over three km of declines and major caverns and pump rooms. The paper describes methods used for design on the project. Emphasis is given to the refinement of the use of empirical rock mass classifications, and to the use of discontinuum numerical methods. The use of empirical rock mass classifications in Sydney sandstone has usually led to conservative design because the systems are based on a random orientation of joints in the rockmass. Because the joint sets are usually oriented in a way that is beneficial for tunnelling, limits must be placed on the parameters used in the classifications system. The paper discusses these limits and the derivation of the parameters. The use of numerical methods in Sydney sandstone is discussed. Continuum methods have their uses, but discontinuum methods are preferred. The use of UDEC has been validated against a previous project, the New Southern Railway. Recommendations are given for UDEC models. In Sydney's geology, so advantageous for tunnelling, the challenges of this project have been to make the best use of the good conditions, while maintaining safety for the workforce and the future operators of the project.

Jan 1, 1999

By David Beck, Eko Wibowo, Hendri Silaen, Andres Sugiyanto, Karl Llewelyn

PT Freeport Indonesia’s Deep Mill Level Zone mine is one of the deepest block cave mines in the world and is in mountainous terrain in West Papua, Indonesia. The mineralization is hosted in a skarn deposit in a structural setting that is complex at the footprint, mine and regional scale. Large seismic events and significant episodes of rapid rock mass deformation are potentially critical geotechnical risks during this ramp-up stage of mining. Understanding the interaction between stress, strain, rock mass strength and geological structures is essential to minimize the hazard and engineer control measures to help ensure the safety of the employees while achieving production targets. This paper discusses how the seismicity and excavation damage have been shaped by the interactions between the mine and geological features, and how this affects strategic mining decisions. Additionally, the paper presents a summary of the mitigation measures used for mining the DMLZ in the safest and most productive way. These include improvements to geotechnical characterization of rock mass and structure, dynamic ground support designs, production scheduling for desirable cave propagation and a seismic monitoring system with re-entry protocols.

Apr 26, 2022

By R. Herrera-Urbina, D. W. Fuerstenau

A large number and a wide variety of chemical reagents are used in flotation processes for wettability and Eh control, particle agglomeration/dispersion and bubble stability. A historical account of the use of flotation reagents through the years since flotation was introduced as a viable and economic process for the concentration of sulfide minerals is given and a review of old and modern postulates of their interaction with minerals is presented. Although the results of surface and colloid chemistry studies with well characterized mineral/flotation reagent systems have advanced our understanding of the role played by these chemicals in the flotation process, many questions remain unanswered. Moreover, new flotation reagents are needed to solve the challenge posed by the treatment of problematic-type ores and fuel deposits that have increasingly become the source of our raw and energy materials. Because of the depletion of high-grade and relatively easy-to-process ores, flotation scientists and engineers are confronted with finding more specific and selective flotation chemicals to effectively and economically concentrate minerals. The development of new flotation reagents is vital for cleaning fine coal and processing polysulfide, polymetallic ores, and mixed oxide/sulfide ores.

Jan 1, 1989

By Frederick B. Henderson

The US Environmental Protection Agency (EPA) has tried many regional and laboratory efforts to develop measurement and monitoring techniques using environmental remote sensing technologies. In 1997, the agency established the Advanced Measurement Initiative (AMI): This is a eadquarters-level program, operating under the auspices of the EPA Office of Research and Development. The program is one result of the April 30,1996 White House Conference on Advanced Monitoring of the Environment. The EPA was encouraged to work with other federal agencies to leverage its remote sensing capabilities and use them to improve the efficiency, cost-effectiveness and flexibility of environmental measurement and monitoring for regulatory compliance and reinvention. During the fall of 1996, the EPA and the Department of Energy developed an interagency effort to broaden the use of governmental technologies for environmental measurement and monitoring. In addition, the EPA and the National Aeronautics and Space Administration (NASA) conducted joint workshops on the use of NASA remote sensing and other technologies for water quality and pollution applications. In the meantime, the EPA proceeded with an industry-proposed workshop to explore ways to cooperatively examine new research and to develop commercial remote sensing systems. It also examined how these systems might become accepted by the EPA in the regulatory and compliance processes. In particular, industry was interested in where new remote sensing capabilities might fit in with EPA's efforts at regulatory reinvention. Historically, the mining and petroleum industries have been reluctant to experiment with or use environmental remote sensing. They were concerned with the unknown liability from potential discovery of previously unknown environmental problems. Moreover, resource industries have been reluctant to use remote sensing for environmental applications where the EPA did not accept such data or information as part of the compliance process. Acceptance by the EPA of these advanced measurement and monitoring technologies (AMMT) will be a major reason for industry's increasedd use of remote sensing in environmental "applications for regulatory compliance. In July 1997, the EPA Office of Research and Development hosted at the Colorado School of Mines a stakeholders workshop on the AMI program and industry-government collaboration. The workshop's aim was to demonstrate the usefulness of AMMT technologies for environmental applications. Stakeholders included the mining and petroleum industries; environmental services companies; state environmental agencies and local governments; remote-sensing, value-added companies and data suppliers. The workshop used specific technologies and applications as a way to develop collaborative demonstration projects for several AMMT technologies covering different environmental problems. The workshop focused on the use of highly sensitive hyperspectral (very narrow spectral bands), geographic information systems and surface mapping to identify active acid-producing mine dumps and wastes from benign wastes at Leadville, CO. NASA's advance infrared imaging spectrometer (AVIRIS) was the instrument used. It was developed at California Technology's Jet Propulsion Laboratory. The EPA, the US Bureau of Land Managment (BLM), the US Geological Survey and several environmental service contractors sponsored the overflight and data evaluation. The AVIRIS study demonstrated reliability (95% correct surface mineral identification) and cost-effectiveness of this technology to accurately map and discriminate active acid-producing mine wastes from benign wastes. It could also predict which streams would be effected by acid and toxic mineral drainage. The BLM'said that the AVIRIS overflight could save it $500,000 a year in surface sampling costs at Leadville. The AMI workshop further outlined five 1997 funded AMI projects of potential interest to the mining industry. They were: ? Mine waste characterization using remote sensing methodologies at Asarco's Ray Mine in Arizona. ? Predictive emissions development and testing in

Jan 1, 1997

By Ricardo Gomez, C. T. Ogryzlo, A. A. Dor

This paper reviews the historical background leading to the development of the project. It gives a description of the exploration program and resulting geological and ore reserve information together with plans for mining. A discussion is included of the three processes investigated for the project: 1. Rotary Hearth and Magnetic Concentration 2. Shaft Furnace and Electric Furnace 3. Rotary Kiln and Electric Furnace Results of pilot plant campaigns conducted at Fiskaa, Norway, and Riddle, Oregon, on the process chosen for the production of ferronickel are presented. The paper continues with a review of the considerations involved in selection of commercial plant equipment and concludes with comments on the current status of the project.

Jan 1, 1979

By Glen L. Black

Choosing a mining method for an underground orebody is a complicated and often iterative process. Advances in technology have given design teams an array of possibilities for methods and equip¬ment. Hecla Mining's discovery of the deep Gold Hunter ore body challenged the staff at the Lucky Friday Mine to determine the optimum mining method. Taking an ore body from prospect to production requires traditional resource characterization. This includes drilling, delineating and modeling. Developing the mining plan is an evolving process, changing with each new piece of in¬formation as the project progresses through exploration and development. The Gold Hunter deposit is a steeply dipping vein system in the Wallace Formation of Idaho's Coeur d'Alene mining district. Gold Hunter is a misleading name for the ore body. The vein is a silver-rich, lead-zinc deposit with only traces of gold. The Gold Hunter ore body is located about 1.6 km (1 mile) north to northeast of Mullan, ID. The ore body is mined from the Lucky Friday Mine, located 0.4 km (0.25 miles) east of Mullan. Mining began on the vein from an access drift driven from the Lucky Friday Mine's 4900 level. Production from the ore zone is projected to be 771 t/d (850 stpd). The Gold Hunter ore is combined with Lucky Friday ore and milled in the Lucky Friday mill. The combined ore boosted Lucky Friday's 1998 silver production from 62.2 t/a (2 million oz/year) to more than 124.4 t/a (4 million oz/year).

Jan 1, 1999

By Joseph E. Worthington

The Haile Gold Mine is one of the earliest gold discoveries in the eastern United States as well as one of the largest gold producers from that region. Gold was first discovered in the gravels of what is now known as Haile Gold Mine Branch in 1828 on lands then owned by Colonel Benjamin Hale (spelling not the same). Small placer workings were immediately started and it was not long before the surrounding residual soils and saprolites were also found to contain gold. Following the presence of gold in the residuum eventually lead to the discovery of the underlying gold-bearing lodes that actually outcropped in saprolite form where not masked by heavy vegetation or a thin veneer of Coastal Plain sand. The earliest attempts at production, immediately after discovery, utilized slave labor, washing gravel and residuum from leased tracts that were 15m (50 ft) square. Several at- tempts at small milling operations were made during the en- suing decades, but there was really no substantial or successful production until the 1880s.

Jan 1, 1990

By J. J. Lewis

In the mid-1970's a major new prospect was proved in a previously unworked region of North East Leicester- shire, United Kingdom. Preliminary estimates from borehole information showed over 500 million tonnes of recoverable reserves. A special Planning Team was set up, to co-ordinate the work for the two local Areas, South Nottinghamshire and South Midlands (management of production of the UK National Coal Board is organised in twelve such Areas). The team was led by one of the authors as Deputy Director, Mining, North East Leicestershire Prospect (NELP). The remit imposed by the National Coal Board was to analyse the possible options of number, location and eventual rates of output of shaft or drift access; to select a recommended alternative in the light of geological, mining, topographical and environmental considerations; and prepare submissions in accordance with standard Board practice on major projects - such submissions including detailed engineering design, financial appraisal, and full risk assessment. To assist the Planning Team, surface and underground consult- ant engineers were appointed to prepare feasibility studies of specific civil and engineering problems.

Jan 1, 1979

By James M. Barker

Marketing is the linchpin of the industrial-mineral (IM) industry. Without markets and consumers for IM products, all other associated IM activities are superfluous. The simple existence of an IM deposit does not mean that it can be exploited. A dynamic interaction between exploration (geology), mining, processing, transport, marketing, sales, and consumers is required for profits. Geology dictates the existence of a deposit, but markets dictate its development, and transportation provides the connection. This is true to such an extent that marketing commonly is called the exploration phase of IMs. Marketing is strategic and includes long-range market-development and planning activities, whereas selling is tactical and more focused on day-to-day consumer interactions. Each will help the other when properly done. Many producers of IMs have failed because of inadequate marketing skill, information, and practice. Over many years at the Montana Bureau of Mines, the many developers seeking technical assistance to find an IM deposit, but who had no marketing plan, always failed. In contrast, the few who sought assistance first on marketing, with the IM deposit to be found later, always succeeded (Richard Berg, personal communication, 1998). Marketing has many facets helped by geologists who must be aware of what marketing is attempting to do. A geologist needs to understand many aspects of IMs: location (deposits, plants, consumers), processing (specifications), transportation (truck, rail, barge, ship), competition (local, regional, national, international), substitutes, pricing, and new developments and market forces of all kinds. Some needed skills are not taught formally to geologists, so well-rounded self-education and on-the-job training are the way a geologist normally enters into IM marketing. The IM geologist generally is associated with marketing either by helping to prepare a market study or by acting on the results of one. Preparing a market study is a two-part process. The first part is relatively simple but requires a time-consuming collation of data into an IM survey (mostly past-and present-oriented). The more difficult and much more important second part entails expanding the IM survey into a market evaluation (mainly future-oriented) that emphasizes forecasting, timing, location, and specific products. A market evaluation generally boils down to formulating the right questions to ask of the right persons. One very good question to ask is, "What could be the market for this specific IM?" while thinking for yourself without excessive recourse to gossip, rumors, promoters, developers, or (at times) IM experts. The evaluation must prove that market potential exists and suggests a marketing plan. Effective marketing is an ongoing process, with the initial marketing plan modified over time, using wide and continuous input to avoid tunnel vision. Industrial-mineral markets are based either on commodity (lower-priced, basic-processing) minerals or specialty (higher-priced, value-added) minerals. IM marketing methods are either product-driven (commodity minerals), a more traditional approach, or market-driven (specialty minerals), but these are neither mutually exclusive nor is one always better than the other. Focusing too much on specialty minerals can lead to problems. A blend of commodity products with specialty products commonly lowers risk and enhances long-term profits. The highest profits occur in specialty minerals at the cost of higher risk and complexity and require intelligent marketing, versatile technical services, and creative research and development. Industrial minerals are best served by an industrial-marketing approach rather than a consumer approach. Modern industrial marketing emphasizes the consumer using the "marketing concept." The marketing concept focuses all management and operational activities on total consumer management and satisfaction similar to the total quality management approaches to excellence.

Jan 1, 1999

By R. Rodgers

The Pinto Valley Concentrator of BHP Copper Inc. restarted its sulphide mining operations in September 2007 to produce copper and moly concentrates. During the plant production ramp up, the copper/moly circuit quickly reached the copper grade and recovery targets, but the production and quality of the moly concentrate continued to be a challenge. Even though several improvements in the moly circuit were completed, the final moly concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns was chosen. The column design and construction were done utilizing in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing moly concentrate to the required specifications, that is, high moly tenors and low copper and iron content. In this paper, the operating parameters, mass balance, design, installation, commissioning and operation of the new flotation columns will be discussed.

Jan 1, 2010

By V. T. Vacariu, P. D. Georgescu, N. Tomus

To assess the potential for radioactive pollution unique to the environmental conditions of the Bacau phosphogypsum waste dump, surface samples were taken, drillings were performed on the entire waste dump's height, and the Ra226 distribution on the height and surface considered to contain a medium content of the radium of 0.57 Bq/gr was studied. Thus, the waste dump's radioactive potential was estimated at 30-40 Ci in equivalent Ra226. Also analyzed was the granulometric composition of the phosphogypsum and the distribution of Ra226 on granulometric orders, which indicated that the radium was concentrated in the very fine fractions. Parameters were set up for the classification by hydrocycloning to obtain a fine class (less than 41 microns) having a radium content of more than 0.9 Bq/gr and a coarse class having less than 0.37 Bq/gr. A chemical process was devised for removal of the radium from the phosphogypsum with the possibility for recovering the contained sulfur.

Jan 1, 1999

By Kotaro Ohga, Kiyoshi Higuchi

In our laboratory, a new detection system using smell detectors was developed to detect the spontaneous combustion of coal and the combustion of other materials used underground. Laboratory experiments were carried out on several kinds of coals, including South African coals, and machine oil, wood and rubber used in belt conveyers. The following results were obtained: 1) Spontaneous combustion of coal can be detected earlier by smell detectors than by conventional CO detection methods. 2) There were no differences in the results using different kinds of coal. 3) Combustion of other materials can also be detected earlier by this system than by conventional detectors for gas and smoke. 4) Use of this detection system enables one to discern the source of the combustion gases, whether it be coal, wood, oil or rubber.

Jan 1, 1995

By Xintan Chang

A computer software package, named CFIRE, for the general ventilation network analysis and fire control, mine fire and/or coal spontaneous combustion, has been developed at Xian Mining Institute in China. It is a multipurpose package with adequate capacities of ventilation map drawing, ventilation network analysis, gob fire simulation, steady state ventilation simulation and transient state ventilation simulation. It was written in a user-friendly style, driven by menus, facilitated by on-screen messages and supported by the allowance of user interferences. CFIRE has used up-to-date research findings focussing on the practical needs of coal mines. This paper discusses briefly also the relevant theoretical principles on which this package has been perceived.

Jan 1, 1989

By Kostas Fytas, Pierre Bousquet, Bill Evanelou

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidise to produce low pH water. This acid effluent has the potential to mobilise any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pynte is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidises a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2000

By Jon Bowler

Daw Mill Colliery, UK Coal, near Coventry in England, mines the Warwickshire Thick Seam at 800 m/2500 ft depth using longwall retreat with gateroads supported by rockbolts. Over the last eight years the mine has worked longer and wider panels with extraction heights of over 5 m. Recently the mine has experienced high deformation conditions principally from the rib sides resulting in operational issues and production delays. Investigation of rib deformation was undertaken using new inspection and measurement techniques, including systematic laser surveying, and improved rib support consumables were developed and introduced. A new rib trussing system using textile webbing has proved very successful.. A rib support management system was also developed and introduced for face retreat. This allowed rib support to be more effectively managed both for production and safety. For the current developments, new 28-mm-diameter roof and rib bolt systems have been introduced and rib bolt length has been increased to 3 m, with the aim of achieving gateroad stability over the life of the panel. Significant reductions in roof and rib deformation have been confirmed by the latest monitoring results. These ground control innovations are allowing Daw Mill?s potential to be realised. Production from 302?s face in 2008 set new UK and European records. However the support enhancement process continues and further innovations are planned.

Jan 1, 2009

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By F. L. Wilke

The prototype of an expert system, designed to assist layout planning of face operations, is presented. By specific combination of knowledge-based and conventional EDP techniques it has been possible to extend the known Kepner-Tregoe method up to the determination of mature layout solutions in difficult planning cases. It has been proven that the presented strategy - which can be applied to any kind of problem with similar structure - is apt to provide efficient EDP support for handling complex mining problems. Such support goes far beyond the purely numeric evaluation of envisaged alternatives.

Jan 1, 1989