Search Documents

By B. E. Davis

A technique was devised by the Bureau of Nines to recover coarse (plus 1.7 m) North Carolina phosphate now discarded as waste. Concentration utilizes the difference in particle sphericity between the relatively flat calcite and the rounded phosphate pebbles. Sizing, treatment in a continuous hydraulic classification system, and grinding upgraded a 17.0-pct-P205 reject to 24.5 pct P205 with a phosphate recovery of 63 pct.

Jan 1, 1985

By Gregg Wilkerson

The Blind Springs Hill pumice beds are located 5 miles southwest of Benton, California in the foothills between the Benton Mountain Range and Blind Springs Valley. The best exposures of the pumice are in an area 0.75 miles west of Blind Springs Hill. The pumice is Quaternary ejecta material which came from the rhyolitic volcanoes in the Glass Mountain-Volcanic Tablelands area of Mono County. The pumice beds occur in two distinct layers separated by an unconformity. The upper layer is 0 to 11 feet thick and consists of coarse subangular pumice fragments, some of which are over 1.75 inches in diameter. The lower bed is medium to coarse grained with subangular fragments up to 1.0 inch. The lower bed is 0 to 9 feet thick. Overburden at the Blind Springs Hill deposit varies from 0 to 15 feet. There are approximately 1 million cubic yards of material in the deposit that can be mined. The size distribution in the deposit is mostly fine with only 10.6% of the pumice fragments being over 0.5 inch in diameter, the minimum size needed for stone-wash or acid-wash applications. Suitability of pumice for the textile industry is quantified by standard 15-minute abrasion and absorption tests. In the Blind Springs Hill deposit, the plus 0.5 inch fraction has an abrasion loss of 33% which is too high for stone-wash application but it has an absorption capacity of 36% which makes it suitable for acid-wash applications in the textile industry. The abrasion and absorption properties of this deposit are within the range of those which have been measured for other pumice deposits within the United States.

Jan 1, 1995

By Frank J. Skudrzyk, Vladimir F. Petrov

In compliance with the current Russian environmental legis­lation, possible impact of industrial activities on the environment is restricted by acceptable limiting values (maximal allowable concentrations - MAC) of individual chemical substances in the natural environment - water, atmospheric air and soils. These norms have federal status and are valid for the whole territory of Russia. Disposal of the substances, for which no MAC is estab­lished, is forbidden by the law. Many gold mining companies use cyanide in precious metal recovery. This paper overviews the Russian experience in pro­tection of natural water reservoirs from technogenic impact of cyanic technologies. Major toxic compounds, contained in liquid and solid rejects from hydrometallurgical treatment of gold ore using cyanidation, are cyanides (CN), thiocyanates (SCN) and cyanide metal com­plexes. Unlike western classification of various cyanide types, in Russia any inorganic cyanide compounds (simple and in com­plexes with metals), with the exception of iron cyanide com­plexes, are considered toxic and the acceptable limiting value is established for them. MAC is 0.05 mg/I for fish reservoirs and 0.1 mg/I for drinking water. For iron cyanide complexes MAC is 0.15 mg/I for fish reservoirs and 0.25 mg/I for drinking water. Russian norms for thiocyanates are practically as rigid - the acceptable limiting value for them in fish reservoirs is at the level of 0.07mg/l (0.15 mg/I for potassium thiocyanate) and for drinking water - O. lmg/1. Norms for metals are established on the basis of total content regardless of the form in which they are present in water - as cations or complex ions. It should be noted, that in case several toxic compounds of the same limiting value (for cyanides, thiocyanates and base metals the limiting value is toxicological) are present in water. Their allowable concentra­tion is calculated as the sum of actual concentration of each com­pound, divided by the corresponding acceptable limiting value, with the result not to exceed one (compounding effect). Differences in cyanide classification and the necessity to include thiocyanates dictate different analytical methods. This, in a number of cases, results in certain discrepancies in analytical results. Until recently chlorination was used as a basic process of detox­ification of wastewaters. Calcium hypochlorite powder or hypochlorite pulp, prepared of lime milk and chlorine shipped to the plant, were used as a reagent. Chlorination is an efficient method: it allows to completely destroy plain and complex cyanide, in addition to iron complexes, and thiocyanates. A good example of high efficiency chlorination can be found at the Mnogovershinniy mill near the Okhotsk Sea located in the salmon spawning area, for which we designed an automated chlorination plant for tailings dam. Since plant start-up ten years ago, the required concentrations of cyanides and thiocyanates have been kept at the MAC level required by environmental regulatory agen­cies and no harmful affects on ichthyofauna has been reported. One major drawback of chlorination is high cost of the major reagent, as well as secondary contamination of detoxified waters by chlorides. Secondary contamination by chlorides becomes obvious in the course of detoxification of wastewaters of com­plex composition, which require increased reagent consumption. Recent changes in economic conditions in Russia caused the necessity to direct efforts to reduce the costs of precious metals recovery, and in particular, wastewater treatment. We have con­ducted certain work in this direction and obtained positive results. We hope that our experience described below will be of interest to other specialists particularly taking into account the current low gold prices.

Jan 1, 1998

By J. T. Kline

This paper will present a review of the underground leaching of remnant copper mineralization left as a result of the block cave mining operation at the Lakeshore Mine in Casa Grande, Arizona.

Jan 1, 1985

By C. J. Gilbert

The mining method at the Cannon Mine uses heading and bench stopes, which are subsequently backfilled with cemented high-strength fill prior to pillar removal. The dimensions of the pillars, 24 feet wide by G5 to 95 feet high, re-quire careful blasting in order to not damage the rock, compromising pillar strength and complicating later removal. Additionally, the proximity of dwellings makes vibration control a must for good-neighbor relations. A blast monitoring study was conducted in order to optimize bench blasting practices to maximize fragmentation, reduce costs, minimize well damage, and minimize ground vibration.

Jan 1, 1989

By Joseph M. Zigich

The Anaconda Minerals Company operates a molybdenite and copper producing mine and mill facility near Tonopah, Nevada. Included with the milling facility is a ferric chloride leach plant for removal of copper mineralization from the molybdenite concentrates. Discussed are the engineering and construction schedules associated with the leach plant. The chemistry associated with the process along with a description of the process flow, equipment, and operating parameters are contained in the paper.

Jan 1, 1983

By B. M. Davis

The problem of assessing uncertainty in grade estimates has been a topic of research and debate since kriging was first introduced. Use of the kriging variance was originally touted as all that was necessary in order to produce confidence limits for grade estimates. Since then the prudence of using the kriging variance for confidence interval estimation has been questioned, and techniques such as the jackknife and conditional simulation have been proposed to develop "true" interval estimates. This paper compares the differences between interval estimates produced by the three methods and makes conclusions about the performance of confidence intervals produced by the different methods.

Jan 1, 1997

By A. Perry

Latin America is in the path of economic growth characterized by increased privatization, joint-venture projects, and reduced trade barriers. Privatization is changing the industrial operating mode from Government-owned/Government-operated to a privately-owned/government-regulated regime. The establishment of joint ventures, such as in construction and management of infrastructure, energy and mining projects, and deregulated industries (electricity/gas/ telecommunications), is now a common practice in the region. These changes, coupled with the growing awareness of environmental protection issues, have led to a sincere effort on the part of the countries of Latin America to establish reasonable environmental regulations and controls (RERCs) for all industries, including mining and energy, for the benefit of present and future generations. However, RERCs require further consideration of many factors with respect to environmental, geologic, economic, and social impacts in the region. The process must find a balance between the need to sustain profitable operations and the need to adequately protect the environment. While striving to find a balance between continued industrial profitability and environmental protection, the RERCs must be scientifically sound, pragmatic, flexible, and enforceable. There has been worldwide attention focused on the environment, and international symposia have been held on such issues as global warming, water pollution, air pollution, and hazardous wastes. Organizations such as the United Nations (UN) and the Organization of American States have performed rather extensive studies on the environment for various industries and activities, and have developed some broad general plans to address environmental concerns. This technical information is available for the asking, and should be considered a starting point for countries embarking on the passage and enforcement of their own RERCs.

Jan 1, 1998

By C. Gregory Knight

Adequate planning for the development, operation, and reclamation of a surface mine requires attention to present and future uses of land, both on the mine site and in the mine vicinity. This paper outlines land use implications of surface mining, and suggests procedures that could link mine planning, mine operation, and reclamation to more general land use concerns. Mining is viewed as a temporary use of land that may irretrievably commit land resources away from some future activities, but may allow other uses, some of which may have been impossible without mining. The paper accepts the premise that surface mining should attempt to minimize environ-mental damage and to maximize future alternative uses of land by appropriate reclamation. I. The Effect of Surface 1'1ining on Land Use Surface mining is a temporary utilization of the land most often criticized because the disturbances it creates are of far greater duration than the actual extractive operation, Resource recovery disrupts existing activity on the land, at least temporarily, and

Jan 1, 1977

By J. A. Bradbury

N. A. Degerstrom, Inc. has constructed and operated a processing plant approximately five miles north of Soda Springs, Idaho for processing a byproduct phosphate treater dust from Monsanto's elemental phosphorus plant, also located in Soda Springs. The plant is designed to produce agricultural-grade phosphoric acid, gallium, and silver. The design capacity of the plant is 54.4t (60 st) of treater dust per day, which can produce 16,326t (18,000 st) of phosphoric acid, 6,600 kg of gallium, and 6,033 kg (194,000 oz.) of silver per year.

Jan 1, 1993

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper examines the effect of bucket geometry (cutting blade profile, floor profile, and blade thickness), speed, motor power output, and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scaled model of a load-haul-dump in full factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated to penetration and draft; muckpile particle size is positively correlated to penetration and negatively correlated to draft (p < 0.0014). The results show that buckets with a semi-spade cutting nose profile yield the highest penetration (mean 118.30 mm) followed by those with the spade (mean 108.88 mm), which also yield higher penetration than those straight blades (mean 95.19 mm). Bucket floor profile and blade thickness had no significant effect on penetration or draft. Also, we determined that increasing the speed and motor power output, simultaneously, can reduce bucket penetration. Thus, operators should not waste energy for no additional gain or even loss in bucket penetration. Also, the work finds speed and motor power output each combine with muckpile particle sizes to affect bucket penetration. This research furthers our understanding of the effectiveness of different bucket geometries in improving penetration and reducing draft for rubber tire loaders.

Oct 29, 2021

By Richard Giffen, Martha Gross, Luca Pellegrini, Pa Ousman Njie

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in Virginia includes parallel 1.5- mile (2.4 km) tunnels constructed using a tunnel boring machine (TBM). The TBM launching and receiving shafts were excavated within the footprint of two reclaimed islands abutting the navigation channel for the Port of Virginia. The shaft excavations—a circular tri-cell shaft at South Island, and a circular-rectangular twin-cell shaft at North Island—were supported by slurry walls up to 190 feet (58 meters) below the island surfaces. This paper describes specic design considerations for these shafts, as well as construction and uality-oversight aspects of their excavation and construction.

Jun 23, 2024

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By George Saratsis, George Exadaktylos

In the marbel industry, ore reserves refer to the produced tonnage of orthogonal prismatic, defect-free blocks of commercial sizes and of marketable aesthetical quality. On the contrary, in the mining sector, ore reserves refer to the tonnage of ore with grade above some cut-off value. While in the mining sector ore reserves are reported according to existing standard guidelines, the marble industry has no standardmethod. The purpose of this paper is to present a method to estimate white marble reserves using drill coring or borehole wall logging and limited joint mapping on exposed marble surfaces. Data pertaining to fracture orientation, fracture frequency, size, and whiteness were collected. The primary phase of marble characterization is followed by the discretization of the orebody into a three-dimensional array of orthogonal prismatic blocks, where the marble whiteness and fracture intensity are attribute values. Both these variables are considered to obey continuous and not discrete probability distributions. The discretization is performed using computer aided design and the Block Kriging techniques. An outline to improve the description of a given marble ore deposit at the exploration stage is presented for the prediction of marble block size distribution from joint count measurements along diamond drill cores. An example case of a white dolomitic marble quarry is used to demonstrate these methods.

May 27, 2020

By Weibai Hu

The flotation separation of wolframite from fluorite and quartz is investigated with chelating agents and neutral oil as synergic collectors. Test results indicated that a-nitroso-ß-naphthol has a strong collectivity for wolframite and selectivity against fluorite and quartz. The 8-hydroxyquinoline has collectivity and selectivity also. They both have a better activity than sodium oleate. However, the cupferron is slightly inferior. The synergism of chelating agents and neutral oil looks promising, especially for fine wolframite particles. The activation effect of Fe2+ and Ca2+ ions on separation of wolframite from fluorite and quartz is slight. The UV absorb-spectra measurements showed that the adsorption of chelating agent on wolframite is multilayer, and flotation behavior is related to chemisorption. The chelating agent which bonds to Fe and Mn sits on the wolframite surface, and the reaction between Mn2+ ion with collector is more significant. The essentials affecting reagent activities are the bonding factor and the hydrophobic factor. These factors are discussed by structure-activity relationship theory. The synergism of neutral oil is a secondary collector likely to lengthen the hydrocarbon chain of chelating agents.

Jan 1, 1985

By V. A. L. Breguncci, A. H. Martins, C. P. Ribeiro Jr.

This work presents experimental results for the recovery of gold present in alkaline cyanide solutions by using the electroelution technique of strong-base anionic polymeric resins IRA 402-CL from Rhom and Haas-Brazil Ltd. loaded with gold. This technique of electroelution of anionic polymeric resins is based on the removal of metal ions adsorbed to the resin, resulting from a potential difference applied between the cathode and anode in an electrolytic cell. The electrolytic cell was composed of an aqueous solution with suitable chemical characteristics and an anionic polymeric resin bed loaded with gold. The resin used in the experiments was loaded using synthetic alkaline gold cyanide solution with 1.0 g/L of gold. The variables studied were electroelution time, cathode current density, distance between cathode and anode and the electrolyte chemical composition. Statistical methods made it possible to establish the optimum conditions that would achieve satisfactory gold recoveries by the electroelution technique. The statistically predicted response for the resin loaded with gold by percolation was 16.5% gold recovery, 2.0 A/m2 cathode current density, 20-mm distance between electrodes and 6.0 hrs electroelution time. For the centrifuging system, the statistically predicted response was 7.41% gold recovery under the following conditions: 0.25 A/m2 cathode current density, 1-mm distance between electrodes, 3.5 hrs electroelution time and 10.9% NaOH in the electrolyte chemical composition.

Jan 1, 2002

By N. Edmonson

An examination of the statistics of the world phosphate fertilizer industry since 1980 reveals an increasing tendency for fertilizer manufacturing activity to concentrate in phosphate rock mining areas. The economic justification for this resource-oriented strategy is clear. The choice between shipping phosphate rock, a comparatively low-value product, and shipping more valuable finished fertilizers will always be resolved in favor of the latter if cost considerations control the decision. The historical existence of substantial phosphate fertilizer manufacturing capacity oriented toward fertilizer-consuming activities and dependent on imported phosphate rock shows that narrow cost considerations have not always determined the industry&apos;s location. One is entitled to ask what conditions have changed to precipitate the observed relocations, and how permanent these changes are. These questions are the subject of this investigation.

Jan 1, 1995

By John W. Harshbarger

The Upper Santa Cruz Groundwater Basin lies in the drainage area of the Santa Cruz River in Arizona, and extends upstream from the community of Rillito to the international boundary, see Figure 1. The principal water use area lies between and includes the cities of Tucson and Nogales. A subsurface geologic barrier near Rillito provides a reasonable dividing line between the groundwaters of the Upper and Lower Santa Cruz Basins. The Upper Basin contains the Tucson and Sahuarita-Continental critical ground- water areas. The Tucson Water Use Area encompasses the Tucson metropolitan area and extends from the northern boundary of the Basin south to the boundary between the Tucson and Sahuarita- Continental critical groundwater areas near San Xavier. The San Xavier Use Area is the San Xavier Indian Reservation. The north and south boundaries of the Continental Use Area coincide with the limits of the Sahuarita-Continental critical groundwater area. The first study of groundwater in this valley was initiated by Dr. G. E. P. Smith in 1905 and the results were published in 1910, followed by a series of bulletins of the Arizona Agricultural Experiment Station, University of Arizona, covering the general field of groundwater development and utilization. Beginning in 1939, the Ground Water Branch of the United States Geologic Survey, in cooperation with the Arizona State Land Department and the Arizona Water Commission (AWC), have published a series of bulletins concerning groundwater occurrence and utilization in various areas of the state. In 1975 and 1977, the AWC published the "Arizona State Water Plan" (1), comprising a detailed inventory of water availability and use in the State of Arizona, and a study of alternative futures.

Jan 1, 1979

By Lester G. Rollins

Coal today enjoys a dominant position, serving the energy and metallurgical marketed The measure of success in the market place is, and will continue to be, the price per million BTUs or price per ton delivered to the user. The Coal Industry&apos;s remarkable record of price stability since World War II is well known. The next twenty years promise to be equally as challenging. This challenge will be met our president, Mr. Drain, has often stated that, ?The Joy Manufacturing Company is betting that coal will meet the challenge.? To this end, the resources of Joy have been committed to doing its part. Joy&apos;s efforts are directed toward a target which has been defined as: 1. Deliver coal to the user at a price of $.15/MBTU or less. or; 2. Deliver coal to the mine portal at a cost of $1.00 or less.

Jan 1, 1966

By Michel Gauthier

Several zinc showings, exhibiting many similarities to the well-known Balmat-Edwards zinc deposits of New York State, occur within the Grenville Supergroup strata of the Mont-Laurier Basin, Quebec. Metallogenic mapping programs have revealed much of the stratigraphic control of this mineralization. This control is observed on both regional and local scales. At the regional scale, these showings are confined to the perimeter of the Mt.-Laurier Basin, while at the local scale, a definite association between the zinc mineralization and dolomitic marble horizons is clearly exhibited from detailed mapping. These new exploration guidelines have proven to be useful for base-metal exploration in the Mt.-Laurier Basin and should be applicable to the entire Grenville Province.

Jan 1, 1983