Search Documents

By R. L. Russell

Production at Freeport Indonesia's Ertsberg open pit copper/gold mine started in 1972 at a rate of 7500 t/d. Mill throughput remained at that rate for a number of years until the discovery of the Ertsberg East (GBT) orebody. This discovery prompted three successive expansion stages from 1981 to 1988 that boosted production to 20,000 t/d. The discovery of the huge Grasberg porphyry copper deposit in 1988 launched a new era of much larger expansions. The first of these involved installation of a fourth primary mill in 1989 to bring production up to 32,000 t/d and was immediately followed by an expansion of the crushing and screening plant and the addition of a new south concentrator to bring production to 57,000 t/d in 1991. The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 has served to optimize current production at a level of 66,000 t/d. A major expansion is now in progress. This includes construction of another new concentrator to house a SAG mill circuit and large Wemco flotation cells in an area created by the removal of 6,000,000t of glacial material. This current expansion, with a planned completion in 1995, will take production to 115,000 t/d. This paper describes the evolution of the Freeport Indonesia (FI) concentrator to-date and will then go into an in-depth discussion of the 66,000 and 115,000 t/d expansions.

Jan 1, 1994

By Bruno Bussière, Michael Aubertin, Robert P. Chapuis

Covers with capillary barrier effects (CCBE) have been used in recent years as gas barriers for the isolation of wastes, including reactive mine tailings. Capillary barrier effects help to maintain a high degree of saturation in the moisture retaining layer, which then reduces gas flux. Various factors affect the degree of saturation of the moisture retaining layer in a CCBE, such as the material water retention characteristics and layer thickness. Slope geometry can also influence the hydrogeological behaviour of a CCBE, but this factor has frequently been ignored in the past. In this paper, the authors show some results of a numerical study that illustrates the influence of slope on the behavior of capillary barriers made of different types of material. The numerical model calculations are based on an actual case of a CCBE constructed in northern Quebec. This investigation shows that the water content profile is greatly affected by the position along the slope. Thus, it is necessary to evaluate the influence of the geometry to properly establish the performance of a cover system.

Jan 1, 2000

By Roy A. Grancher

?The Horn of Plenty seems to have sprung a leak?.? anonymous For the first time in the Nation's peace-time history, shortages have become a way of life for the United States. Such words as scarce, tight, and critical are used in regard to supply, leading to priorities, allocations, and possible rationing as make-shift attempts to satisfy demand. Almost every day a new type of shortage appears in another product area that has traditionally been taken for granted as being in perpetual abundance. The range of coverage extends from basic commodities such as oil, chemicals, cement, steel, copper, cotton, etc., through to machine tools, motors, bearings, electronic components, etc. , to those finished outputs that satisfy our fundamental requirements for food, clothing and shelter. Signs of the times appear in cancelled airline flights, unfilled lines at gasoline stations, no available home freezers, lengthy delays in any furniture deliveries, or to that little old lady seen walking out of a local supermarket clutching her hoard of twenty rolls of toilet paper. What a sad commentary to have to make about our Land of Plenty, so long the envy of the World for its material wealth -- and today with its initials "U. S." seemingly standing for ?Unlimited Shortages.?

Jan 1, 1974

By A. K. Raina

Blast induced damage to the final wall of rockmass in any civil or engineering application is a major concern to the rock excavation engineers. There are at least four distinct techniques practised by blasting engineers to minimise the damage to the parent rock during blasting that are classified as contour blasting. One of the methods to achieve a smooth wall or rock surface in blasting is pre-splitting, where blastholes in the final row are mildly loaded with explosives and fired first in sequence before the rest of the holes in a round of blast to achieve a split in rockmass. Since blasting is one of the most adopted methods for achieving a final wall in a desired shape, while maintaining the rockmass integrity, the design of pre-split blast assumes importance. There are several variables that determine the final shape of the pre-split face including the rock type, the drill diameter, the explosive characteristics, the orientation of major joints with respect to drill hole, the linear charge density, the spacing of drill holes and inclination of the drill holes. This study attempts to determine the importance and sensitivity of variables in pre-split blasting using historical data from open excavations of a hydroelectric project in India. Keeping in view the multitude of variables, low correlation of independent variables with responses and high level of interactions between the variables that define the blast results, it was found suitable to use ANN to determine the importance and sensitivity of the variables involved. A new method to determine the blast induced damage to rockmass, namely, undamaged area (AUD%), is introduced. Half Cast Factor (HCF%) and AUD%were calculated for a high wall and trenches by digital image analysis technique using the Fragalyst software. Joint spacing and linear charge density emerged as most controlling variables in determining the final result of pre-blast. The relative importance of other variables assuming significance in the case of both the designed outputs is also discussed. A comparative analysis of HCF%and AUD%on the basis of results obtained from ANN analysis is also presented. A futuristic approach concept has also been introduced.

May 30, 2021

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By E. W. Greig

This paper is an account of exploration for bauxite in the Amazon Basin, Brazil, and particularly of the discovery, exploration and development by Alcan of the Trombetas deposit so a general account of the Trombetas Project has already been published in E/MJ (Anon. 1975) to which the reader is referred for details on owner-ship, infrastructure and construction as well as the proposal for mining and treating the bauxite. It is impossible to consider the Trombetas deposits in isolation. A regional account of bauxite in and around the Guyana Shield and the northern portion of the Brazilian Shield is included and it is suggested that these deposits all formed during Tertiary time under similar conditions.

Jan 1, 1977

By A. M. El Shafey, Ahmed W. Hussein, Ibrahim M. Gaafar, Mona M. Fawzy, Mohamed Diab, Mohamed S. Abu El Ghar

The Quaternary stream sediments of the Diit area, southern Red Sea coast, Egypt, were mineralogically studied for their content of economic heavy minerals. The study area covered approximately 450 km2 and included three main parts: Wadi and Delta Diit, as well as Diit lens. The mineralogical investigation revealed that these sediments contain considerable amounts of placer ilmenite, magnetite, zircon, sphene, apatite, garnet, and rutile. Also present, in minor or trace amounts, are uranothorite, monazite, xenotime, fergusonite, khatyrkite, and gold. The magnetic fractionation tests, supplemented with the XRD and SEM mineral analyses, indicated the presence of Fe-oxide minerals as wuestite, hematite, and maghemite accompanied with magnetite as products for hand magnet separation. Ilmenite separation was carried out using a high intensity magnetic separator at a current of 1 A, while the paramagnetic minerals (e.g., garnet, pyroxene, amphibole, epidote, monazite, xenotime, and fergusonite) were separated as magnetic fraction at a current of 3 A. The non-magnetic minerals (e.g., zircon, apatite and rutile, uranophane, uranothorite, gold, and khatyrkite) were obtained at 3 A current. On a mineralogical and geochemical basis, the present work suggests that Diit stream sediments should be considered as a potential source for Ti, Fe, Zr, Zn, and Cu after the physical upgrading processes for concentrating the minerals carrying the aforementioned economic elements.

Jan 21, 2022

By S. Chatterjee

Mining represents the first industry in the United States to have federally mandated training for its workers. Although the topics to be covered are specified in 30 CFR 48, course content is left to the discretion of the individual mine operators. Unfortunately, certain topics to be covered, such as prevention of accidents, are usually mine specific, making it very difficult to use the same course content in every mine. Further, training requirements may change from one mine to another, due to changes in the demographic characteristics of the workers, or changes in job and organizational characteristics. Therefore, if the intention of safety training is to modify the behavior of workers, it is expected that there should be some changes in the content of safety training programs in order to address the specific requirements of individual mines, or at least mines of similar worker and job characteristics. This study has been directed towards the development of a systems-based procedure for conducting a needs analysis. A special effort was made to understand the psychology of worker behavior by analyzing worker reactions to various organizational and job characteristics.

Jan 1, 1994

By A. B. Cecala

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U.S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1993

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Scenario-level uncertainty is a representation of large-scale differences encountered when considering ultimate mining pits optimized over various subsets of stochastic realizations. Accounting for scenario-level uncertainty allows mine plans to be assessed against several probabilistic subsurface interpretations. Scenario-level uncertainty is found through clustering stochastic geostatistical realizations and optimizing final pits across the realizations in each cluster. Where these pits are geometrically different, plans for each scenario differ. Knowing these differences allows the value of each planning alternative to be assessed based on the value and relative probability of each scenario. These results also facilitate the use of formal decision-making frameworks for planning, leading to optimization that better represents the full statistical characterization of the deposit. An example utilizing this approach evaluates both infrastructure placement and drilling program requirements. In both cases, scenario-level uncertainty improves initial plans by limiting opportunity costs and identifying additional potential.

By Clement K. Chase

Since the dam of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extractions. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2018

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2017

By Steven J. Van Kauwenbergh, Talaat A. B. Lawendy

Batch laboratory-scale beneficiation tests were conducted on four high-iron phosphate samples. These samples included sedimentary ores (Tilemsi Valley, Mali and Tahoua, Niger), a sample from an igneous phosphate deposit (Matongo, Burundi), and a fine-grained phosphatic iron ore processing residue from Chile. The Matongo phosphate deposit occurs as a thick (up to 80 m) residual blanket of P205-enriched soil over solid parent rock (carbonatite and associated rock types). Although the Matongo deposit is an igneous deposit, ore from the deposit can be subjected to beneficiation treatments commonly used to treat sedimentary rocks. The beneficiation flowsheets designed to process these diverse ore types involve attrition scrubbing, size classification, and flotation. At the best flotation conditions tested, phosphate concentrates assaying 32.0%-39.0% P205 and 1.0%-1.5% Fe2O3, were obtained at 64.2%-82.2% overall P2O5 recoveries from run-of-mine (ROM) ores containing 9.2%-28.6% P205 and 5.9%-16.1% F,20,. A cleaner phosphate concentrate assaying 33.1% P205, 1.8% A1203, and 3.3% Fe2O3 at 53.4% overall P205 recovery was obtained from the phosphatic iron ore residue that originally contained 4.5% P205, 8.0% A1203, and 17.6% Fe2O3.

Jan 1, 1993

By G. G. O. O. Uwadiale

Because mineral matter is finely distributed within the matrix, Nigerian Labia coal is nonresponsive to conventional processing techniques. However, testing has shown that Lafia coal can be upgraded by selective oil agglormation. The optimum oil concentration was found to be 10 mL of paraffin per 25 g of coal. A product containing 6% ash and 1.9% sulfur was obtained with a yield of 90%. Optimum results were achieved with a grinding; time of from 2.5 and 3 hrs, which produced a 98% -400 mesh product. However, further grinding wars found to be deleterious to the process. Also, high pH adversely affected concentrate yields. Utilizing kerosene as a bridging liquid, a product containing 4% ash and 0.33% sulfur was achieved at a natural pH of 6.3 with a yield of 85%. At pH 9 and 10, a product containing 4.5% ash was achieved with a yield of >90%.

Jan 1, 1997

By C. Xiao, R. Chi

In recent years, the biosolubilization of rock phosphates by phosphate-solubilizing microorganisms has become a major topic of research studies. However, the microorganisms used in previous studies were mostly single and known species, and studies seldom focused on mixed communities of microorganisms or microbial consortia from natural environments. In this study, a microbial consortium from rhizospheric soil was used to solubilize two different compositions of medium- to low-grade rock phosphates — designated as ore samples 1 and 2 — in a laboratory-scale bioreactor. The microbial consortium showed good growth in the bioreactor, reduced the suspension pH and released soluble phosphates from the ores. Scanning electron microscopy with energy-dispersive X-ray spectroscopy showed the action of the microbial consortium on the ore surface. There was considerable corrosion on the ore surface, and 3.42 and 4.93 percent of the element phosphorus was removed from ore samples 1 and 2, respectively. Microorganisms were sampled from the bioreactor for the analysis of their community structures by Illumina MiSeq high-throughput sequencing. The analysis show that the suspensions added with different ore samples had different microbial diversities and richness. This study provides new insight into the biosolubilization of rock phosphates by a microbial consortium directly taken from rhizospheric soils.

WELCOME to the world-class Cripple Creek district where gold exploration and production continue 95 years after the initial discovery. More than 21 million troy ounces of gold have been recovered, valued at greater than $7.8 billion using today's gold price ($371/oz). The Cripple Creek district is localized within and around the margins of a silica-undersaturated alkalic diatreme-intrusive complex. The diatreme appears to be comprised of three sub-basins: 1) a sub-basin east of the Cresson (Fig. 1); 2) a southwestern sub-basin between Victor and Cripple Creek; and 3) a northwestern sub¬basin within which the Globe Hill and Ironclad pits (Fig. 1) are located. The recognition of three separate basins was made by G. F. Loughlin and A. H. Koschmann (1935, Fig. 8) who prepared a contour map on the floor and walls of the composite Cripple Creek basin. The northwestern and southwestern sub-basins are apparent due to the discontinuous exposures of a partially exhumed ridge of Precambrian rocks (Fig. 1). The separation of the eastern and southwestern sub-basins was recognized in mine exposures where a fault-bounded ridge line extends from the vicinity of the Ajax mine toward the Precambrian "island" (Fig. 1).

Jan 1, 1986