Search Documents

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"Abstract — The use of diesel equipment in underground coal mines is controversial because the National Institute for Occupational Safety and Health (NIOSH ) regards ""wholediesel exhaust"" as ""a potential occupational carcinogen."" Threshold limit values (TLVs ) are recommended for the gaseous pollutants CO, CO2, NO, NO2, SO2 and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sample these aerosols.The University of Minnesota and the USBM have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) that utilizes size selective, partial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines that used diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine a quality.Air quality data were collected in four underground coal mines. The mines used continuous miners and diesel haulage equipment. Daily samples were collected at the section intake, haulage way and on haulage vehicles. Both full- and partial-shift samples were collected using a variety of aerosol instruments. These included the PDEAS and the micro-orifice uniform deposit impactor (MOUDI) that sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO,CO2, NO, NC, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.Concentrations of CO, CO2, NO, NO2 and SO2 were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed was 0.79 mg/m4, with a standard deviation of 0.19 mg/m3 DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 022 mg/m3."

Mar 1, 1992

By J. Drew Potts

The U.S. Bureau of Mines identified respirable dust sources and controls on four continuous auger mining sections, two with relatively low dust levels and two with high levels. Factors adversely affecting dust levels included auger equipment design, continuous haulage, and low seam height. Dust controls included ventilation practices and spray systems. Maximizing airflow seemed to reduce dust levels most. Air leakage and shock loss can be reduced by constructing stoppings with brushed-on mortar containing fiberglass and by keeping areas between curtains and ribs free from obstructions and storing equipment not essential for face activities in outby crosscuts. Curtain configuration, setback distance, and installation can also affect dust levels. Use of both blowing and exhausting curtains is the most effective configuration. Setbacks from the face should not exceed 15 ft. Installing brattice curtains at least 5.5 ft from ribs, when entries are 26 ft wide, minimizes velocity head. Installing curtains tightly against the mine roof and floor helps maintain a forward airflow movement in the center of the mine heading; curtain overlap can create a tighter seal. The wet-auger spray system also effectively controls dust, provided the mine is already exercising good ventilation practices.

Jan 1, 1989

By John D. Foulkes, David A. Curtis, Robert L. Lagace, John L. Rothery

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal mines. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to deter- mine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m5 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to be attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977

By John C. Machisak

The Nation's mining and quarrying industries have again met the annual challenge to their ingenuity--that of reducing disabling work injuries among their employees. The effectiveness of management in facing this problem and in meeting this responsibility from the results of the 1961 National Safety Competition. Three hundred ninety-three or 45.3 percent of the mines and quarries participating in the competition established a new record number of participants operating throughout the competition year without a disabling work injury. Another record established in the 1961 contest was the number of participants (868) enrolled in the competition. This annual safety competition was begun in 1925 and is conducted by the Bureau of Mines, U.S. Department of the Interior. It provides for six bronze Sentinels of safety trophies which are awarded each year to the winning participant in each group. Since its inception, the competition has exerted a strong influence in the field of safety promotion. The statistical record of its accomplishments over the years gives strong support to the theory that well-organized and well-administered safety programs are effective tools to be used to reduce the number of disabling work injuries. It stimulates and holds the interest of employees and management in accident prevention. Because of this, mines and quarries participating in the contest have a more favorable safety record than those operations not enrolled.

Jan 1, 1963

1. Proposals were submitted to the Western Administrative Center of the US Bureau of Mines, Denver, Colorado on 30th December, 1974 and Contract No J 0255003 was awarded, the effective date being 8th May, 1975. Dames and Moore, Denver, are associated with PD-NCB Consultants in regard to environ-mental problems, surface mining practice and legislation in US. BACKGROUND TO THE STUDY 2. Under the threefold pressures of -increased domestic fossil fuel demand -increased value of domestic energy resources -increased demand for environmental protection and safety

Jan 1, 1976

By E. C. Lane

This report on properties of commercial motor fuels is the twelfth in a series made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report contained data on motor gasolines sold during the winter of 1935-36.V The -present report, covering the summer of 1941, presents analytical data for 1,857 samples, representing the products of approximately 135 companies. As in previous surveys, these companies include both large and small suppliers. In addition, the Pacific coast is represented by data averaged by the Pacific Coast Technical Group before being submitted, and these data are published exactly as they were received. Conforming to previous surveys, the data cover three groups of samples -- regular-price, premium-price, and third-grade gasolines -- and each group has been aver aged separately. The number of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, are as follows: Regular price, 1,010 samples, 291 items, and 86 brands; premium price, 577 samples, 263 items, and 78 brands; third-grade gasoline, 270 samples 159 items, and 74 brands. The meanings of these terms as used in the surveys are as follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.

Jan 1, 1942

By M. A. Schellhardt, E. J. Dewees, R. Vincent Smith

"INTRODUCTION Abnormal material requirements of the nation at war impose an intensive demand upon many irreplaceable natural resources. Natural-3as reserves) for example, are being subjected at the present time to extensive depletion by large-scale withdrawals of gas to supply unprecedented demands for fuel and raw materials for the synthesis of strategic products. Fluids produced from many so-called gas-condensate type reservoirs have become an important source of hydrocarbons vital to the war effort.Development of gas-condensate type reservoirs in Arkansas, Louisiana, and Texas in recent years created many problems not common to ordinary gas-producing operations. Early in the development of condensate-type gas fields, general practices were evolved and applied to insure efficient re¬covery of the hydrocarbons existing in the gas phase under initial reservoir pressures and temperatures, put often the practices were predicted mainlyregardingupon generalized theory regarding the behavior of the fluids and were not always the most efficient, because field and laboratory procedure for testing these hydrocarbons had not progressed as rapidly or as far as field development. Specific information regarding the composition and properties of fluids ultimately recoverable from many gas-condensate reservoirs, especially, is lacking."

Oct 1, 1944

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By Clyde E. Williams

[As a results of work conducted during the past three years, the Northwest Experiment Station of the Bureau of Mines, in cooperation with the University of Washington at Seattle, Washington, has developed a process for the production of sponge iron. Commercial operation of this process in a 3 to 4-ton scale has been so satisfactory that its use on a large scale (20 to 100 tons per day) can be safely considered. Description of Process. The process consists in passing a mixture of iron ore and coal through a rotating kiln heated at one end to a temperature sufficient to convert iron oxide to metallic iron, discharging, cooling, and separating the sponge iron from the residual coke and silicious material on a magnetic separator. Both the coal and the ore should be crushed to peso as 6-meth scream, tans producing particles finer then 1/12 of an inch. Seventy-five parts of coal or other carbonaceous material arc charged with every 100 parts of ore), This large amount of coal is required in order to supply sufficient carbon to maintain a strongly reducing atmosphere in the charge, but may be reduced to about 65 parts per 100 parts of ore by recovering and using tae carbon that remains in the discharge product. Large-scale operation and refinements in furnace design should lower this ratio to perhaps 56 or 60 parts of coal to 100 parts of ore.]

Jan 1, 1924

By Ronald B. Stotelmeyer

This report summarizes studies of 28 National Forest roadless areas in Montana completed by the U.S. Bureau of Mines (USBM) in the period 1974-1993. It also briefly describes 20 areas for which field studies have not been conducted. All 48 of these roadless areas have been recommended for addition to the National Wilderness Preservation System or proposed as special management areas by the U.S. Forest Service (USFS) or the Montana congressional delegation. The Bureau studies indicate which parts of the roadless areas have a high likelihood for mineral-resource development. They also show where mineral production has occurred in the past and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character. For the purposes of this report, mine refers to a property which produced (or is currently producing) a mineral commodity, a prospect is a property which has been explored but has no record of production.

Jan 1, 1994

By Nils A. Eilertsen

This Bureau of Mines report describes the unit cost procedure for estimating direct development costs within a cave block in an undercut block caving mine. Costs of supervision, labor, equipment, and supplies are combined to build a unit cost for each type and size of mine development opening in the block. These costs are then combined to estimate the direct cost for developing a ton of ore. Operating data from several domestic metal mines are combined with a hypothetical mining system to illustrate the costing procedure.

Jan 1, 1975

By John R. Troxell

"INTRODUCTION The Ahles iron mine, also known as the Pequest mine, in Warren County, N. J., was operated continuously for 15 years and was still in ore when it closed in 1916.Tie property was examined by an engineer of the Bureau of Mines in March 1943. 3/ This examination led to an investigation of the deposits by the Bureau by diamond drilling two holes under the old workings to determine whether the extends downward.This report describes the work done at the Ahles mine by the Bureau and presents the data obtained.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report.The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation was under the general supervision of J. B. Zadra, acting regional engineer, and under the immediate supervision of G. D. Jermain, district engineer for the States of Pennsylvania, New Jersey, Maryland, and Delaware. The author was in direct charge of the project.The chemical analyses for the project were performed at the College, Park, Md., laboratories of the Bureau of Mines under the direction of M. S. Sheftel. The ore-dressing tests were conducted at College Park under the direction of Frank Lamb. Preston E. Hotz, of the Federal Geological Survey, logged and interpreted the drill cores."

Apr 1, 1948

This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-363/. The second report gave the same data? for motor gasolines sold during the summer of 19364/. The third report of the series gave the same data for motor gasolines sold during the winter of 1936-375/. This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others.

Jan 1, 1937

This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-363/. The second report gave the same data for motor gasolines sold during the summer of 19363/. The third report of the seriis gave the same data for motor gasolines sold during the winter of 1936-375/. This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative that others.

Jan 1, 1937

By Loren R. Anderson

This volume documents the use of the probabilistic slope stability program PROBISH. The probabilistic slope stability program is an interactive program and is essentially self-tutorial. It prompts the user for the required input data as it is needed, and allows the user to correct mistyped data before analysis is initiated. The program computes safety factor probable Width of failing and probability of failure for a given circular failure surface. Four example problems are included to illustrate its use.

Jan 1, 1982

By Hugo E. Camargo

Noise Induced Hearing Loss (NIHL) is the most common occupational disease in the U.S. with devastating consequences particularly in the mining industry. A study conducted by the National Institute for Occupational Safety and Health (NIOSH) revealed that 90% of coal miners have hearing impairment by age 50, compared to only 10% of those not exposed to occupational noise. According to the Mine Safety and Health Administration (MSHA), Continuous Mining Machine (CM) operators account for 30% of workers exposed to noise doses exceeding the Permissible Exposure Level (PEL). This number becomes more dramatic considering that 49% of the total national underground coal production is extracted using these machines. In this context, NIOSH is conducting research to identify and control dominant noise sources in CMs. Previous noise source identification was performed using a Brüel &Kjær (B&K) 1.92-m diameter, 42-microphone phased array. These measurements revealed that the impacts from the conveyor chain onto the tail roller, and the impacts from the conveyor chain onto the upper deck are the dominant noise sources at the tail-section of the CM. The objectives of the work presented in this paper were: 1) To rank the noise radiated by the different sections of the conveyor, and 2) to determine the effect of a urethane-coated tail roller on the noise radiated by the tail-section. This test was conducted using an Acoustical and Vibrations Engineering Consultants (AVEC) 3.5-m diameter, 121-microphone phased array. The results from this new test show that a urethane-coated tail roller yields reductions in the tail-section of 2 to 8 dB in Sound Pressure Level in the frequency range of 1 kHz to 5 kHz. However, integration of the acoustic maps shows that the front-section and mid-section of the conveyor also contain dominant noise sources. Therefore, a urethane-coated tail roller in combination with a chain with urethane-coated flights that reduces the noise sources in the front and mid sections of the conveyor is required toyield a significant noise reduction on the CM operator?s overall exposure. These results show the applicability of phased array technology for low frequency noise source identification.

Jan 1, 2008

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lower-grade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful large-scale concentration of law-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district.

Jan 1, 1917

By E. L. Garton

Analyses of samples of crude oil from fields in West Texas have been published from time to time in Bureau of Mines reports.3/ Analyses of 100 samples of crude oil from West Texas) collected during 1946 to 1952) are presented in this report. The production of crude oil from the fields in this portion of Texas totaled 381,129,000 barrels4/ during 1951 - an amount greater than that of any previous year. Total cumulative production of this area through 1951 was 2,792,692,000 barrels.5/ Table 1 gives monthly production figures for 1951 and yearly totals for the preceding 10 years (1942-1951) [ ]

Jan 1, 1953

By E. D. Eastman

There are three researches upon the specific heat of water vapor by the method of explosion that are sufficiently advanced in technique and suitable in plan to justify careful study of their results , with the double purpose of fixing the best available experimental values and indicating the attainable accuracy of the method. These three researches comprise the work of Pier , Bjerrum , and Siegel.5 The work of earlier date than Pier's suffers from obvious inaccuracy of measurement , while the experiments more recent than Siegel's , such as those of Womersley6 , of Bone and his collaborators , and of Maxwell and Wheeler , 8 are for the most part not well designed for the accurate determination of the heat capacities in question . Some of the errors to which they are especially subject have been discussed by David and by David and Thorp.

Sep 1, 1930

By C. H. Riggs

This report of a petroleum-engineering study of the Flat Rock oil field, Osage County, Okla., describes the geology, reviews the production history, and estimates remaining oil reserves. The Flat Rock field in the southeastern corner of Osage County approximately 6 miles northwest of Tulsa. Okla., was discovered in November 1904. The field was one of the first of many Bartlesville-sand fields developed in eastern Osage County during the early part of the 20th century. Although substantial oil reserves remain in the pressure depleted sands in some parts of the field, their economic recovery by water flooding will require careful consideration of the many factors involved.

Jan 1, 1954