Search Documents

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013

By Ruilin Yang

"Blast vibrations are essentially a strain/stress wave propagating in rock or structures inthe vicinity of a blast. However, blast vibration has always been quantified in terms ofpeak particle velocity (PPV) or acceleration (PPA), and a meaningful relationshipbetween blast vibration and strain/stress has not been established. The determination ofthe dynamic strain from blast vibration may improve quantification of blast damage andselection of a blast vibration limit for critical structures or high walls. Dynamic strainrelates to rock mechanics or material strength more directly than peak particle velocity(PPV). This paper documents a method to calculate the three-dimensional dynamic straintensor from recorded blast vibration signals. The method is based on determination of thedisplacement gradient at a point of interest for each time instance during the vibrationduration. The method to calculate dynamic strain is applicable to generic seismicwaveforms including near and far field blast vibration from a production blast withmultiple blast holes. In order to minimize measurement errors the specifications of thespacing between monitors and the sampling frequency of the vibration recording aredescribed."

Jan 1, 2012

By Roberto Folchi, Hans Wallin

Lake Mead, the largest man-made reservoir in the United States, is located about 30 miles southeast of Las Vegas, Nevada. For the construction of Lake Mead third water intake, which is entirely placed underground, an underwater excavation was needed at a depth of 100 m (330 ft): a large surface had to be deepened by 20 m (66 ft) in basalt.

Jan 1, 2012

A simple and cost effective technique to increase fragmentation and burden velocities without making major modification to the overall blast design is with ALTERNATE VELOCITY LOADING OR BOOSTERING OF ANFO. The technique requires the placement of a cartridge or slug of explosive, having higher density and detonation velocity than ANFO, every few feet in an ANFO column. The greater the difference in density and detonation velocity of the Alternate Velocity Load to ANFO, the more pronounced are the results. Emulsions were selected as the Alternate Velocity test explosives because they detonate closer to ideal conditions than most other commercial explosives.

Jan 1, 1989

By Edward Walter

Rock excavation for tunneling projects occurs on a regular basis in the Cleveland area. These tunnels are being constructed to increase the capacity of the sanitary sewer system. Controlled blasting must be performed to remove rock in a number of phases of the project. The rock excavation for construction of a junction chamber is just one case where blasting is the safest and most efficient method available.

Jan 1, 2001

By Randall S. Marks

Bonneville Dam, completed in 1938, included the smallest and busiest lock on the Columbia and Snake River Navigation System. To expedite barge traffic through this restriction, a new larger lock was designed and contracted by the U.S. Army Corp of Engineers.

Jan 1, 1997

By Jack Curran

KANSAS CITY, MO - Performing one of the most impressive urban building-implosion projects in recent memory, Tulsa, Oklahoma-based Dykon Explosive Demolition Corp. and Omaha, Nebraska-based Anderson Excavating recently felled the landmark Columbia Bank Building in downtown Kansas City, Missouri, USA. Although every structural blasting project presents special challenges, this undertaking was most notable for its unusually unique structural design, tight clearances, and high risk to adjacent structures.

Jan 1, 2003

By Tony A. Rorke, Joe R. Brinkmann

The application of instrumentation to better understand and improve production blasting is one of the most fruitful areas of explosives and blasting research. The majority of instrumented studies of production blasting have relied on the extrapolation of far field measurements to postulate blast performance in regions of interest closer to the charge where rock breaking takes place. However, the nonlinear and dissipative nature of the quantities being measured raises serious questions as to the accuracy and validity of such extrapolations.

Jan 1, 1991

By H. Venkatesh, Balachander R.

This article discusses the method that was adopted for controlling damage to rock mass while excavating an underground powerhouse cavern at Tala Hydroelectric Project. It discusses in detail the near field vibration studies carried out and the safe vibration levels established for that rock mass condition.

Jan 1, 2006

By Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance. Using the site parameters from the analysis of signature hole vibrations, the present blast vibration model yields reasonable agreement with field measurements in terms of vibration amplitude and frequency. Case studies show that the model has been used successfully to assist field vibration control.

Jan 1, 2010

By Nils Heinke, Stephen M. Collinsorth

To anyone who is responsible for the production of blast holes, who is looked to on a daily basis for drill maintenance and performance, whose bottom line may depend on the survival of the mine itself.. How much awareness should one have on such things that truly impact production, maintenance and overall job cost? Do you know your drill’s maximum capacity?

Jan 1, 1998

By Tianrui Xu, Chaohong Liu, Bangqing Ding

The authors were responsible for a series of large scale multiple chamber charge blasts conducted in the granite mountain area for making construction space on the southeast sea coast in China during 1993-1996. This paper describes the blast design and damage control of one mountain blast 320m in length and 280m in width in the vicinity of two wharfs and a dam. In order to obtain better rock fragmentation and muckpile, the explosive charge should be well-distributed in the mountain. The charge pattern, therefore, was designed with mainly 5 rows of tunnel charge in regular terrain in combination with a chamber charge in irregular topography area and the maximum burden was limited to be less than 38m. In order to protect the dam and wharfs the firing sequence was carefully arranged in 29 intervals and the distance between different charges of the same delay to the dam or wharf was taken into account as an additional delay interval based on the difference of p-wave propagating times. The maximum charge fired in an interval was also limited to less than 34t explosives through dividing the larger charge by a stemming deck.

Jan 1, 1998

By Paul Kunze

When a new bridge was needed across the upper reaches of the Yellowstone River in Montana, removing the old concrete bridge piers became an environmental concern for the highway department engineers. The location is about fifty miles downstream from the north edge of Yellowstone Park. The determination was made by the federal and state agencies charged with protecting the resource, that the old piers had to go but the river bed had to remain unchanged. Concerns were expressed that removing the concrete presented the potential for environmental damage to this protected portion of the river. These concerns prompted the state to place stringent restrictions on the contractor in the way they carried out the demolition and disposal of the piers. The reinforced concrete masses had to be removed to an elevation at least fifteen feet below the river bed and every bit of concrete debris had to be removed from the river channel. Explosive removal was discouraged, but the only other options: saw cutting, mechanical or chemical breaking, were not viable.

Jan 1, 2014

By David G. Borg, John Bussey

The new AIRDEK (tm) technique for pre-splitting in surface coal mines produces highwall conditions that have greater safety with lower costs for explosives, labor, and drilling. Successful applications have been made in highwalls ranging from 20 to 100 feet or more and in blasthole diameters from 3-1/2 inches to 12 inches.

Jan 1, 1988

By Pierre De Pasquale, Aquilino Antonio Alvarez-Castro

Greenhouse gas emissions are now an essential issue for extractive industries. Actually, lowering of quarry energy consumption and CO2 emissions participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry.

Jan 1, 2016

By Sri Sawmliana, P. Pal Roy

Blasting Gallery (BG) method was introduced in India for higher production and low cost of excavation to substitute conventional hand section and stowing methods for thick coal seam. The Singareni Collieries Company Ltd. (SCCL) adopted this method in the year 1989 and since then successfully operating at GDK-10, GDK-8 & VK-7 Incline mines in Andra Pradesh, a southern state of India. It is also successful at Chora 10 Pit Colliery of Eastern Coalfields Ltd. (ECL) in West Bengal whereas at East Katras Colliery of Bharat Coking Coal Ltd. (BCCL) in Jharkhand State, the method has been partially successful due to some geological constraints of the area.

Jan 1, 2003

By Will Hunt, Darren Thornton

In March of 2013, an undisclosed gold mine (MINE X), located in the Western United States, performed blast movement monitoring of three blasts occurring in one of two active pits. Blast Movement Monitors (BMMs) were placed in the bench before blasting, and located after the blast to determine vectors of movement. Using blast movement software, ore/waste boundaries were translated. These locations were compared to MINE X’s standard ore translation procedure, which consisted of moving polygon boundaries by 17.5 feet (5.3 m) in the burden direction of the blast hole pattern. This translation amount, identified by MINE X as “average” motion, had been ascertained by performing a previous blast movement study.

Jan 1, 2014

By Qian (Ken) Liu, Remi Proulx

A large scale blast damage project was carried out over the past two years at INCO Ltd Manitoba Division co-funded by the Canada/Manitoba Mineral Development Agreement. The experiment was conducted at the T-3 Mine in two mining stopes with an experimental drift developed in the hanging-wall for the installation of monitoring instrumentation. The objective was to observe and subsequently to reduce ore dilution by monitoring the performance of blasts, the hanging wall movement, as well as the cavity of the open stopes.

Jan 1, 1995

By George P. Jr Schivley

Looking at the process of drilling rock from the standpoint of the power required, yields an equation that relates Force-on-the-Bit; Torque, to rotate the bit; and bit Angular Speed to the Penetration Rate of the bit; the Area of the hole being drilled and the Specific Fracture Energy of the rock. Specific Fracture Energy and the Compressive Strength of the rock are related.

Jan 1, 1994

By Earl C. Hutchison, Wade C. Hutchison

T 0 effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre- and postblast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995