Search Documents

By Mohammed Y. Fattah, Wissam H. S. Al-Sudani

"During installation of pile, a soil column is formed inside the pile. For small depths, the height of the soil column typically equals to the penetration depth (full coring state). As the penetration depth increases, the developed internal shear stresses become larger and reduce the amount of soil to penetrate. At the same time, the soil in pile at the bottom is compacted. This will continue until at a given moment, the soil column is a soil plug, and does not stop moving relative to the pile. This is because the shear stresses developed in the interior of the pile are greater than the load-bearing capacity of the ground.This paper presents the results obtained from 40 model pile tests carried out to assess the effect of soil plug on the model pile capacity. The piles are embedded in sand of different densities with different lengths of piles and types of pile-ends. The model tests are divided into two parts according to the type of end of the pipe pile used in the model pile test. The first part consists of 32 model open-ended piles with different lengths of soil plug inside the pile. The second part consists of 8 model closed-ended piles.It was concluded that open-ended pipe piles behave as a closed-ended if the soil plug formed inside piles in state partial plug or full plug. Length of soil plug depends on the type of installation and relative density. The pile load carrying capacity in dense sand is several times greater than those in medium sands especially in cases of closed ended piles or open-ended since the pipe pile can produce external and internal skin friction in addition to end bearing resistance that makes the total pile capacity close to that of closed-ended pile. Whether open-ended piles are driven or pressed in the fully coring - fully unplugged mode or in the partially plugged mode, the plug does contribute to static pile base capacity."

Jan 1, 2014

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

By Suk han Jang

This paper describes the tower foundation design and construction experience for the 345kV Youngheung marine transmission line, which has been in commercial operation in Korea since July, 2004. This transmission line was designed and constructed to meet the rapidly increasing power demands of metropolitan areas and supply stable, bulk electric power from the Yonghung thermal power plant into metropolitan areas. This transmission line passes over the west sea, Lake Sihwa and over land. In order to successfully complete this project, and to safely support the tower during severe maritime conditions, several types of tower foundation such as Pad and Chimney foundation, Pier (Cylindrical) foundation, R.C.D foundation, Jacket pile foundation and Steel pipe pile + concrete mat foundation were developed and used. As the world?s first and longest marine transmission line, the 345kV Yonghung marine transmission line operates successfully, thanks to several high-tech civil engineering technologies and KEPCO?s accumulated experience.

Jan 1, 2007

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By Bruno Gemmi

The objective of the ? 200 million ($280 million) project Parma Railways Station-Urban Transformation was the reconnection of the North and South parts of the town by constructing an 80 m (250 ft) wide sunken artery passing under the four double railway tracks of the station without any impact on train traffic. The site of the project, adjacent to the Parma River, presented water seepage problems at any excavation depth. The use of conventional large diameter bored pile machinery was not allowed by the Railway Authority because equipment dimension and construction phases do not comply with train traffic safety regulations. Foundations for the bypass were thus constructed by minipiles nested into jet-grouted soil using machinery operating within the existing head room and at a safe distance from the tracks. Jet-grouting treatment reached depths of 25 to 28 m (80 to 90 ft) from tracks? grade and embedded minipile-heads were terminated at 2 to 3 m (6.6 to 10 ft) below grade. Load tests on minipiles were pushed to failure. Failure occurred at a 240 t (265 t) load without breakage of the bond between the jet grouted soil and the minipiles. A 0.93 MPa (135 psi) shear resistance ??? between minipile steel casing and the jet grouted soil was measured prior to the failure of the steel casings. Overall measured foundation settlements were well within expected values and were considered insignificant.

Jan 1, 2011

By Ketan H. Trivedi

This paper describes the method of analyses used for the design of temporary and permanent Secant Pile Walls, describes various aspects of construction including, guide walls, sequence of pile installation, plan alignment and verticality tolerance, methods of drilling (auger, wash boring, cased and open holes), lateral bracing for secant piles, cutting of keys in secant pile walls for the connection of permanent floor slabs, sealing of water leaks and waterproofing. The paper concludes with a brief case history of a secant pile wall project recently constructed in New York City.

Jan 1, 2006

By John E. Lens

Minutes after the Friday afternoon October 16, 2009 announcement that the 80 year old Lake Champlain Bridge was closed to traffic out of concern for public safety, emergency detour planning started at VTrans and NYSDoT. The closure severed a cross-lake link between Addison, VT and Crown Point, NY, which created a 76 mile detour and significant hardship for commuters, farmers working on both sides of Lake Champlain, and businesses relying on both traffic and employees commuting between Vermont and New York. Rehabilitating the bridge was determined to be economically and technically unfeasible and the design of a replacement bridge was accelerated for a spring 2010 construction start. In the meantime, a temporary ferry alternative was to be rushed into service beside the original bridge by February 2, 2010. This paper presents the case history of the fast-tracked ferry dock design and construction on the Vermont side. Twin 300-foot-long pile supported approach spans, a loading slip system and ice deflectors were designed, fabricated and constructed in 90 days in the fall/winter of 2009-2010. This chronicles the project from initial concepts through the extraordinary cooperation between state and federal agencies, and near round-the-clock winter construction on Lake Champlain. This project and its companion project on the New York shore succeeded by virtue of exceptional cooperation between seasoned regulatory, design, and construction participants and warrant this case-history presentation of the Vermont project to share within the industry as an example of overcoming extraordinary challenges.

Jan 1, 2011

By Robert A. Field

Static-Load Piledriving systems utilize hydraulic push to advance piles into the ground. Dynamic systems (ie. hammers and vibratory equipment) utilize impact, or vibration, to advance the piles. Static-Load systems are most commonly utilized in situations where noise or vibration would adversely affect the people, structures or equipment located near the site. Static-Load technology is most advantageous in situations where vibration, noise or access constraints make it difficult, risky or disruptive to utilize conventional piledriving systems.

Jan 1, 1995

By G. F. Sowers

Excavation bracing is a special structural system. It is built from the top down. The design is controlled by the economical construction of another structure as well as by the movement of the ground beyond the limits of its construction. It serves a number of purposes, all subordinate to the construction of the principal structure. Despite its importance, bracing design and construction is frequently overlooked in project planning, causing delays and expensive changes. Thoughtful planning, good design and resourceful, innovative construction can improve construction safety and save time and money.

Jan 1, 2010

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By Ron Bromenschenkel

The State of California, Department of Transportation is currently retrofitting a major interchange near the San Francisco area. The project is located in a highly traveled area of Oakland with light rail commuter service near many footings. Over 600 micropiles are being used in conjunction with CIDH piles for footing stabilization. A specially designed Soil Nail pile will support footings for a new light rail utility structure. Pile testing features in this contract serve as points of interest for future foundation designs. The presentation focuses on substructure issues of this incterchange retrofit. Both design and construction considerations will be covered. Design Considerations: ? Project Description ? Structure inadequacies ? Design criteria ? Design contraints ? Retrofit strategy ? Consultant analysis ? Pile Designs and Test Sites ? Contract Specifications ? Construction Plan and Cost

Jan 1, 1998

By Upendra L. Karna

The pile capacity gain with time evaluated and implemented for the construction of the Route 21 Viaduct in Newark, NJ, U.S.A is discussed in this paper. The project consisted of the replacement of more than 3.2 km of viaduct and ramps. The project site consists of thick residual materials deposited by the Wisconsin Glacier over sedimentary rocks. The upper portion is glacial-lacustrine deposit underlain by marginal morainic till and stratified drift. Subsurface investigations identified significant variations in layer thickness and grain size consistency. The site was characterized into 4 Soil types, based on subsurface soil behavior. Closed end 600 mm and 450 mm diameter driven pipe piles were used for the foundation. Loading tests conducted during an advanced construction contract, established that a significant soil set-up could be expected. For the first construction contract, a pilot loading test program consisting of 112 dynamic loading tests and 77 re-strikes (at 2 to 4 weeks) using the PDA (Pile Driving Analyzer) with CAPWAP (Case Pile Wave Analyses Program) was conducted to establish the soil set-up behavior. Nine (9) quick static loading tests were conducted to substantiate the long-term pile capacity. Based on the loading test results, average set-up factors were established and utilized for developing production pile driving criteria. Bearing resistance with depth was analyzed and reviewed. The set-up factors varied significantly, ranging from 1.05 to 1.89, and averaged about 1.30. Conclusions are derived. Set-up factors behavior for each soil type plotted by linear regression are presented and discussed. An appropriate set-up with time relationship for a glacial soil is suggested.

Jan 1, 2006

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

By Ray Schmahl

The Glenwood Canyon is a 13 mile long river gorge formed by the Colorado River approximately 2 miles East of Glenwood Springs, Colorado and approximately 150 miles West of Denver Colorado, (See Drawing #1). The canyon walls rise some 800 feet from the river elevation on either side of the river. The South-side river bank is occupied by the Denver and Rio Grande Western Railroad. The Northside is currently occupied by completed sections of Interstate 70 and US Highway 6. The railroad was built in the late 1800's and a hydroelectric power generating station was built in about the center of the canyon in the early 1900's. The Highway 6 platform was completed in the 1930's. The design and alignment for Interstate 70 thru Glenwood Canyon began in the early 1970's. The Highway thru Glenwood Canyon was designated a scenic Highway by the United States Congress, thereby allowing certain deviations from standard Interstate requirements. Environmentalists objections to the construction of Interstate Highways thru Glenwood Canyon resulted in especially careful design to avoid adverse environmental impacts. As a result, in many areas the new Highways will have restored the canyon to its more native configuration than what was the case in the building of the US 6 Highway platform.

Jan 1, 1990

By Rolf Katzenbach

The principle questions related to the design of deep foundations especially in soft soils are the stability and the cost optimised settlement reduction to prevent possible damages and to minimise the deformations of the adjacent infrastructure. The present develop­ments in the design of deep foundations lead to the design approach of the Combined Pile-Raft Foundation (CPRF) which offers a lot of new possibilities, e.g. the utilisation of the CPRF for horizontal loading or the use of the subsoil as a geothermal storage system.

Jan 1, 2006

By W. Lum

In the U.S., flexible metal pipe culverts are designed by ring compression theory because the pipes are capable of deflecting and deriving side support from surrounding ground. For economy, tunnel liners are often designed as flexible structures that depend on the lateral pressure of the surrounding ground to maintain stability. In this paper, simple formulas are presented to determine the maximum deflection a concrete tunnel liner may assume and the ring compressive strength of the deflected liner. A tunnel can then be constructed to work within these limits. Similar techniques may be used to design concrete pipes.

Jan 1, 2010

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By Dan A. Brown

This paper describes a method of conducting rapid lateral loading tests of deep foundations in which the load is applied to the foundation with a time duration of less than one second. For purposes of this paper the loading is applied using a pyrotechnic loading system commonly referred to as Statnamic. However, the method should apply to any lateral loading system which produces a force time history with a loading duration of 20 msec to 1 second. The test provides a measure of the dynamic and static response of the soil/foundation system and must be evaluated as a dynamic loading. Interpretation of the test includes a simple single degree of freedom (SDOF) model which can account for the inertial effects of foundation mass, system damping, and static foundation stiffness. The results of the test measurements are compared with four case histories in which comparative static load test data are available, including pile group foundations and large diameter drilled shaft foundations.

Jan 1, 2007