Search Documents

By R. Paul De Bruyn

A. Crane Check List -- Make -- Model -- Year of Manufacture -- Where is load chart? Is it for this crane? -- Boom style and length -- Boom tip drawing (sketch) for fixed lead connection. Has the crane manufacturer been consulted on the point of attachment? -- How many drums; diameter and length of wire rope. -- Is the single part line pull enough to lift pile or hammer on single part line? -- What is the effective weight of the whole driving system - leads, pile, hammer, etc? -- Are there any auxilliary hydraulic systems? Are the line pulls on these adequate to lift the pile or hammer? -- What is the anticipated working radius? Will the spotter collapse to that length? -- Nature of foundation under crane - barge, marsh, unstable sand, etc. -- Does the crane meet OSAH and state regulations -current certification. Note - the operator is responsible for compliance with regulations. -- Is there any extra weight added to counterweight by compressors or hydraulic systems? What does crane manufacturer say? Consult factory before adding.

Jan 1, 1990

By Wanchai Teparaksa

Pile deviation generally can happen after installation of driven pile particularly in soft soil layers. In this case study, all 242 diameter 0.8 m spun piles were deviated from 20 to 820 mm. The large deviation was caused by lateral soil movement in the top very soft clay layer of thickness about 23 m. This very soft marine clay is very sensitive and anisotropic having high water contents of over 120% and low undrained shear strength of 5-10 kN/m2. The remedial works were carried out based on theory of load transfer and soil-structure interaction. All deviated piles were rectified and used as the foundation piles with strictly controlled pile load tests. The construction of a nine-storey building was successfully completed founded on the rectified piles and it has been opened for the service for over two years.

Jan 1, 2002

By Osvaldo Valdez, Matteo Bertoni, Aem Ragy

The East St. Louis Deep Cutoff Wall project is located in the area of East St. Louis, Illinois, across the Mississippi River from the city of St. Louis, Missouri, along the left descending bank of the river. The project is a fundamental part of the U.S. Army Corps of Engineers' (USACE) effort to rehabilitate and secure the aging East St. Louis levee system that provides flood protection to approxi- mately 250,000 residents and more than $4.5 billion in economic value. The project was devised and de- signed by USACE as a cutoff wall to be installed in the Metro East Sanitary District levee segment, one of the levee segments that form the East St. Louis system. The contract for the construc- tion of the cutoff wall was awarded in November 2019 to Bauer Foundation, the American subsidiary of the Bauer Group.

Sep 1, 2023

By Khamis Y. Haramy

Curing temperature, density, and moisture significantly affect the velocity measured in the crosshole sonic logging, the rate of strength gain, and the final strength of concrete in drilled shafts and, thereby, affect their structure capacities. Non-destructive field measurements can enhance the QA/QC program by measuring temperature, density, moisture, and sonic velocity of curing concrete during the construction and curing of drilled shafts. The curing environment can greatly affect the concrete strength, and requires close attention during construction. This article shares the experience with the NDE technology used in the QA/QC program in the drilled shaft construction. To understand the mechanism by which a drilled shaft cures under field conditions, two newly constructed drilled shafts were monitored for up to seven days, immediately following concrete placement using the following geophysical logging methods: a) temperature logging; b) crosshole sonic logging; c) gamma-gamma density logging; and d) neutron-moisture logging. One additional drilled shaft was also monitored to a shorter duration. Temperatures were monitored using the sensor in access tubes and/or thermocouples embedded at the center of a drilled shaft and near its reinforcing cage. For a small shaft under 1m diameter, curing temperatures appeared to peak at 41° ? 68° C at different depths at around 24-hour curing time and decreased to and stabilized at around 23° ? 35° C in 6 days. The shaft curing rate varied with depth, shaft diameter, surrounding geo-material types, and the depth of ground water. CSL logging was performed in one shaft from top to bottom from six access tubes and limited monitoring in another shaft. The velocity increased with curing time till 4 to 7 days, and, at a specific time, the velocity appeared to be inversely correlated to curing temperatures. The gamma-gamma density log (GDL) results from 5 different depths were obtained at a source-detector separation of 355 mm. The average density was found to increase with curing time, but decrease slightly in 3 to 5 days. At a given time the GDL density curves seemed to correlate with the neutron monitoring logging (NML) moisture curve. The NML moisture was monitored from 1st to 6th day after concrete placement. The moisture was highest when surrounded by bedrock, then clay, and sand due to different hydration rates.

Jan 1, 2007

By Abhijit R. Sheth, Craig M. Benedict, John Brun, Ara G. Mouradian

"Amtrak recently replaced the 1907-era bascule two-track bridge over the Niantic River between East Lyme and Waterford, Connecticut. The project included new approach embankments, with approximately 2,500 lineal feet of retaining wall along the west approach and 780 lineal feet of retaining wall along the east approach. The paper focuses on the design and construction of the east approach retaining wall, whose alignment is directly adjacent to an existing wetland area which required protection. An anchored prestressed concrete sheet pile retaining wall was selected for the east approach. A combination of concrete anchor piles and ground anchors were used to support the wall. The design of the wall took into account two simultaneous train live loads, support of electric traction catenary structure foundations, and construction live load, while at the same time preventing permanent impacts to the adjacent wetlands. The design considered challenging subsurface conditions, shallow groundwater, the close proximity of the existing operating tracks, construction staging, and storm surge events in Long Island Sound.INTRODUCTION AND PROJECT HISTORYThe National Railroad Passenger Corporation (Amtrak) recently replaced the 1907-era bascule two-track bridge (No. 116.74) over the Niantic River, between East Lyme and Waterford, Connecticut, along the heavily-traveled Northeast Corridor (NEC). The two NEC tracks, which carry over 50 trains per day, run east-west over a narrow spit of land known as “The Bar”, which separates the Niantic River’s marine estuary to the north from the Niantic Bay to the south, before crossing the river. The bay is an arm of Long Island Sound and is occasionally subject to storm surge from hurricanes.The 1907 bridge was built as a replacement for the previous 1891-era swing-span bridge, and was constructed parallel to, and 49 feet north of, the swing-span structure. The two-track 1907 bridge consisted of a single-leaf bascule span and four approach spans supported on stone masonry piers and abutments. The new bridge increases horizontal navigational clearance for marine traffic in the river from 45 feet to 100 feet, and vertical clearance from 11.5 feet to 16 feet above mean high water with the bridge in closed position. The new bridge, constructed 58 feet south of the 1907 structure, features a single-leaf bascule span of 141.5 feet, with an approach span on either side."

Jan 1, 2017

By Olgun

Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.

By Hubert Law, Amin Rahmani

This paper evaluates the effects of pile diameter on the initial modulus of subgrade reaction and proposes modifications to the subgrade reaction moduli that are commonly used in the current state of practice based on American Petroleum Institute (API) guidelines. Three-dimensional continuum finite element model of a soil-pile system is simulated under monotonic lateral loadings to develop benchmark data. The benchmark data, which includes small (0.5 ft) to large (10 ft) diameter pile responses, is used to estimate the initial modulus of subgrade reaction for each of the considered pile sizes. The study shows that the subgrade reaction moduli provided by API may underestimate the actual soil stiffness at the soil-pile interface for large diameter piles and may overestimate it for piles smaller than a certain diameter. A simple equation is proposed herein to adequately estimate the initial modulus of subgrade reaction for all pile diameter ranges. The proposed equation is validated by the measurements of full-scale field tests.

By Paul R. Lear

Sustainability continues to be an important aspect of remediation and infrastructure projects. Deep soil mixing (DSM), a common construction and remedial technology, can easily incorporate the following sustainability best management practices (BMPs), including Minimizing Total Energy Use and Maximizing Use of Renewable Energy; Minimizing Air Pollutants and Greenhouse Gas (GHG) Emissions and Maximizing Use of Machinery Equipped with Advanced Emission; Minimizing Water Use and Impacts to Water Resources; Beneficial Reuse of Materials/Reduction of Materials and Waste Reduction; Use of Local Labor and Supplies. This paper focuses on the sustainability of DSM treatment and provide carbon footprint calculations at least one completed DSM project which used these sustainability BMPs to demonstrate the environmental impact of the sustainability.

Sep 8, 2021

By George Burke

"Many soil mixing methods have evolved over the years, but the Trench Cutting Re-mixing Deep method (TRD) was developed in Japan, circa 1993, to construct continuous uniform cutoff walls, without the need for an open trench. TRD mixing has been used on over 300 projects in Japan for excavation support, groundwater barriers, liquefaction mitigation, soil improvement and pollution containment. To date, TRD mixing has been used on only three projects in the United States: a test cell in Long Beach, Calif., for seawater intrusion barrier in 2004; a groundwater barrier at a wastewater treatment plant in Lincoln, Calif., in 2005; and presently at Herbert Hoover Dike surrounding Lake Okeechobee in southeastern Florida.The most notable benefits of TRD are its abilities to overcome difficult geology, such as layered rock and dense cobbles and gravels that hinder other soil mixing methods, and to create extremely high-quality walls. The method is ideal for situations in which access precludes the use of more traditional methods due to spoil control, such as waterways and congested urban environments or subsurface obstruction/difficult ground. Spoil disposal is minimized since TRD mixes the soil in place.TRD mixing has a horizontal continuity advantage over traditional multi-auger deep soil mixing (DSM) systems. Because DSM systems create walls by overlapping soil-cement columns, the auger may be deflected by difficult ground, and gaps are possible. Gaps may also occur when constructing an exceptionally deep wall due to the possibility of auger deviation from its required vertical alignment.The method also has a homogeneity advantage in layered soils. Because DSM constructs columns by rotating the defined length mixing tools up and down the soil profile while injecting binder, strength and permeability in each layer will vary. The TRD method vertically mixes the entire profile and core samples show highly uniform strength. It is most cost-effective in deep difficult ground such as layered rock or dense cobbles and gravels."

Jan 1, 2009

By David R. Sutfin, Joseph Lodde

110 N. Carpenter is new commercial building located in the West Loop neighborhood of Chicago, Illinois. The new home to the McDonalds Corporation work headquarters, accelerated project delivery methods were essential to meet the scheduling demands for this project along with other projects slated to start in the region. As such top-down construction methods were utilized to allow for above and below grade construction to proceed in parallel in lieu of more conventional bottom-up construction methods, thus compressing the project schedule. To achieve this plan, perimeter secant pile walls were constructed in conjunction with interior columns/drilled shafts and a shear wall core constructed from inside a temporary cofferdam. The use of secant pile walls allowed for efficient accommodation of a variety of loading conditions including: exterior curtain walls loads, perimeter column loads, tower crane foundation loads, and in-plane shear loads. Furthermore, this system allowed for efficient and fluid operation of equipment on site in order to accommodate the 90-day window allotted for initial foundation construction. INTRODUCTION 110 N. Carpenter is a recently-constructed 9-story commercial building located on the old Harpo Studios property in the West Loop neighborhood of Chicago, IL. The construction of this 55,750m2 (600,000 ft2) structure is significant to the continued commercial development of Chicago as nearly 46,450m2 (500,000 ft2) of the building houses the new world headquarters for the McDonald’s Corporation, which had moved from Chicago to the suburb of Oak Brook in 1971. McDonald’s recommitment to this urban environment is not only a reinvention of the long-established fast food giant but the anchor for a broader redevelopment of the West Loop neighborhood. Since the opening of this building was seen by the developer, the City of Chicago and others as a key to future local projects, innovative solutions were required to showcase forward-thinking design as well as expedite the construction process. The final result of the design/planning process is a structure consisting of nine levels of above-grade commercial space and two levels of below-grade parking, providing approximately 300 parking spaces. The above-grade structure consists of a reinforced concrete flat plate system, including two-way slabs, columns, and two core/shear wall systems for lateral support. With an average depth of 7m (23ft), the below-grade structure consists of interior components similar to the above-grade structure (structural slabs, columns, shear walls) but includes a perimeter secant pile wall that was designed to support lateral earth pressures; vertical forces from the exterior curtain walls, perimeter columns, and the construction tower cranes; and in-plane lateral forces to reduce the demand on and quantity of interior shear walls. The use of a secant pile wall is a key component to the project because it accommodated the use of top-down construction methods to accelerate the construction schedule.

Jan 1, 2019

By Amr Sallam, David Thompson, Moataz Hassan

"The Little Lake Harris (LLH) Bridge was constructed in 1951 to replace the eastwest County Road 48 Bridge connecting the towns of Howey-in-the-Hills and Astatula in Lake County, Florida, United States. The 78-span bridge carries two lanes of traffic, is 3,130 feet long, and 36.1 feet wide. The concrete deck is supported by steel I-girders carried by one row of 18-inch square precast concrete driven pile. In the late 1980's, slight settlements were observed in several bents. In 1990, Florida Department of Transportation (FDOT) initiated annual survey of deck elevations during bridge inspections to monitor settlement. Due to the slow nature and magnitude of settlement, substructure instability was not a major concern to the department. However, public concern over the settlement and rough ride of the bridge continued to rise. FDOT contracted Kisinger Campo & Associates Corp. (KCA) to provide the needed design to correct the dips in the riding surface and minimize future settlement. KCA's initial design was based on the concept of ""helper bents"" at the settled bents in order to restore the bridge to original elevation. Estimated construction cost for seven helper bents was about $3.3M. FDOT requested evaluating other alternatives to reduce the cost of the bridge restoration. KCA involved the geotechnical consultant, Terracon Consultants, Inc. (Terracon), to perform a peer review and provide an economical alternative solution. Jacking and shimming the bridge was determined to be both technically viable and economical with a total cost of less than $300K. The design was completed in March 2010 and construction was completed in February 2011. This paper provides an overview of the LLH Bridge history, summarizes the evolution of the design methodology including the findings of the geotechnical study and presents lessons learned during the design and construction of the project.INTRODUCTIONThe Safety and Preservation of the State Highway System is the top priority of the FDOT. Therefore, FDOT initiated a bridge management program that starts with conducting biennial safety inspections performed by Certified Bridge Inspectors (CBI). The inspection reports together with the CBI’s recommendations are reviewed by a registered Professional Engineer (PE) and work orders are issued with priority ranking depending on the severity of the bridge deficiencies. If the scope of work is considered beyond the in-house crews’ capability, the work is then included in a contract for and bid. LLH Bridge was a little different. It was initiated in direct response to number of complaints the FDOT District 5 Structures Maintenance Office (D5SMO) received regarding settlement of the Little Lake Harris Bridge."

Jan 1, 2015

By David S. Graham, Paul J. Axtell

Crosshole Sonic Logging (CSL) non-destructive integrity testing identified anomalous readings near the base of a 6.5-foot diameter drilled shaft rock socket. The anomaly was confirmed to be a defect by subsequent coring and core hole camera inspection. A large void and exposed rebar were visually observed in one of the core hole camera inspections. The center of the shaft was then excavated initially with 3-foot diameter tooling and subsequently with 4-foot diameter tooling as part of the remedial actions to address the defect. While excavating with 3-foot diameter tooling, the shaft defect was not encountered. Excavation with 4-foot diameter tooling revealed the defect, a significant void around the majority of the shaft circumference. The void extended radially from the circumference of the 4-foot diameter excavation to beyond the reinforcement cage to the exposed wall of the rock socket around approximately 80 percent of the shaft circumference. CSL results and observations made during remedial shaft investigation and excavation are in good agreement. The shaft defect, located primarily outside of the reinforcement cage, was effectively identified by CSL testing. Although the defect was confirmed by investigative coring, the remedial excavation demonstrates how the investigative coring could have easily missed the defect. This paper shows how CSL results compare to physical observations made during a rare opportunity to characterize the full extent and nature of a drilled shaft defect originally identified as an anomaly by CSL testing. INTRODUCTION The case history presented here pertains to a drilled shaft for a multi-shaft bridge pier in the Midwestern United States. However, the observations presented in this paper are not a result of unique site conditions or the particulars of the project. The lessons learned from this case history are applicable to almost any drilled shaft constructed in the wet. The overall length of the subject shaft is 22 feet including approximately 12 feet of permanently cased, 7-foot diameter shaft extending to bedrock and approximately 10 feet of uncased, 6.5-foot diameter rock socket. The shaft is designed to resist axial and lateral loads and considers the contributions of side and base resistance in the axial design. Six, 2-inch diameter steel Crosshole Sonic Logging (CSL) tubes are include in the shaft. The bedrock at the shaft location includes beds of sandstone, shale, and limestone. The shaft was drilled using conventional drilling equipment and tooling, and water was used as the drilling fluid. Conventional drilled shaft concrete appropriate for underwater tremie-placement was placed via a 10-inch diameter open hopper tremie.

Jan 1, 2019

By Joram M. Amir

During recent years, the integrity testing of piles has made considerable progress. With the availability of portable and powerful computers, practically all integrity testing equipment is now digital. Using sophisticated software for data acquisition and analysis, today's testing systems can provide owners with important information regarding both the length and integrity of piles and drilled shafts. This sophistication carries a price: Very few clients, including experienced engineers, do understand the strange-looking graphs adorning the reports they get. In fact, most of them will never ask, some because they are too busy to care and others because they are ashamed to show their ignorance. This situation is well exploited by a few shrewd operators of test equipment. Facing strong competition and falling revenues, they simplify their task and cut their expenses by the following means: 1. Using old equipment until it falls apart, and then some, 2. Hiring under-qualified personnel, 3. Staying on site as little as possible, 4. Eliminating the analysis and evaluation stage altogether, 5. Confirming as-made lengths and reporting no defects.

Jan 1, 1999

By Morgan NeSmith

The Port of Palm Beach is a full-service landlord port in Riviera Beach, Florida. The port and its tenants process more than $14 billion in commodities. About 80% of these are exports, which makes the Port of Palm Beach one of only 16 "Export Ports" in the U.S. More than 2.5 million tons of cargo move through the port every year. Ozinga, a fourth-generation family- owned construction materials company, has supplied ready-mix concrete for commercial, residential, public works, landscaping and excavation projects from several of its Florida locations. It planned to build a one-of-a-kind cement storage facility to receive and store international ship- ments of cement for transport to other facilities for the production of ready- mix concrete. Dome Technology, of Idaho Falls, Idaho, designed and constructed the 125 ft (38 m) diameter storage facility. The design and working volume of cement for the facility was just under 27,000 cu ft (765 m3). The design loads required to be supported by the foundation system are shown in this table:

Apr 1, 2023

By Yoshinori Kurumada, Masaya Watanabe, Kenji Sasa

"The Port of Yokohama is strengthening its international competitiveness as a strategic container port in order to respond appropriately to global exchange and shipping demands. Thus, the Minami Honmoku main Pier is currently being developed. The high-standard container terminals MC-1 and MC-2 have already started their service, and the development of the container terminals MC-3 and MC-4 is currently in progress.Because the South Honmoku Pier plays an important role in waste disposal management of Yokohama, a final waste disposal site (controlled final landfill site) is being developed in Block 5 to provide long-term and stable reception of waste that will be generated in the city. For this project, a revetment with water-blocking properties and an extension approximately 1.7 km in length is being built in order to prevent water from leaking from the disposal site. The base part of the revetment will be subjected to foundation improvement using the Cement Deep Mixing (CDM) method in order to secure water shielding of the soft sediment underneath the water, prevent slipping of the seawall, reduce the amount of subsidence, and increase the foundation support force.This report presents a preliminary study on using CDM on reclaimed soil and the construction process of the development project of the disposal site in Block 5 of the Minami Honmoku Pier, which has been underway since 2007.ABOUT MINAMI HONMOKU PIERThe development of the Minami Honmoku Pier started in 1990. It was designed to develop high-standard berths with greater water depths in order to handle the increasing volume of foreign container cargo and growing size of vessels. Figure 1 shows the layout of Minami Honmoku Pier. In April 2001, the Phase 1 (MC-1 and MC-2) began services. This is the newest pier in Port of Yokohama.This pier has one of Japan’s largest terminal areas (40 ha) and is equipped with 22 row-type mega gantry cranes capable of handling the newest ultralarge container ships. The pier has a quay with a water depth of 16 m, which is the first in Japan. The pier is equipped with advanced facilities and equipment to let Port of Yokohama be internationally competitive and function as an international commercial hub. An innovative system for high-efficiency transport is currently being introduced; it includes the installation of waiting vehicle lanes and a reservation-based loading and unloading system.Since the fiscal year 2007, a new container terminal (MC-3) with a -20m deep quay capable of handling the increased size of container ships and the diversification of port logistics has been under construction and is nearly completed."

Jan 1, 2015

By Takashi Enomoto

"The cement deep mixing (CDM) method has a wide range of applications, both on land and at sea. This paper describes the features of the equipment on CDM vessels engaged in maritime construction in Japan: the DCM No. 3 barge, the DCM No. 6 barge, and the DCM No. 8 barge. The DCM No. 3 barge is a large vessel with a mixing area of 5.7 m2. The design of the elevator of the deep mixing unit on the DCM No.3 barge enables us to conduct deep underground/ sea operations. This enables us to conduct mixing at depths of up to 52.6 m below the seabed and up to 70.5 m from the water surface. Additionally, since the tower is installed on the center of the barge, it has excellent stability. The DCM No. 6 barge and DCM No. 8 barge are mid-sized vessels with a mixing area of 4.6 m2. The DCM No. 6 barge was fitted in 2013 with energy conservation equipment and upgraded to an environment-friendly CDM barge. The energy saving upgrade used electric power, instead of hydraulic power, by inverter controlled alternating current motor for both mixing unit and main hoisting winch. This enables the using on effective use of regenerative power when the deep mixing unit is lowered. A feature of the DCM No. 8 barge is that it has an inclinable tower located at the bow section for elevating the deep cement mixing unit. Since the tower can be greatly inclined, the hull has a lower center of gravity and greater stability when the vessel turns. This also allows the vessel to pass below bridges and simplifies cruise preparations, outfitting and dismantling work.INTRODUCTIONThe cement deep mixing method (CDM method) involves mixing and stirring a cement-based solidifier into soft ground to rapidly bring the ground to the desired firmness. This method is used to suppress ground shear deformation, increase strength, increase slip resistance, and mitigate liquefaction and subsidence. It has been recently used in Japan in the construction of revetments at controlled waste disposal sites, both to boost the strength of the seabed and to prevent the seepage of waste matter and other pollutants. Undertaking CDM construction work at sea requires specially constructed marine construction CDM vessels. Since CDM construction at sea entails many more restrictions on working conditions than construction on land, the vessels themselves sometimes need to be modified. This paper will describe 1) the remodeling of the turrets and mixing machinery for mixing to great depths in deep water (DCM No. 3 barge with eight axes); 2) the upgraded of equipment on board CDM vessels after accounting for environmental considerations (DCM No. 6 barge with four axes); and 3) the use of a inclinable tower (DCM No. 8 barge with four axes)."

Jan 1, 2015

By Pierre Gouvin

This paper describes the design, installation and monitoring of a state of the art real time geotechnical/structural instrumentation monitoring system to facilitate tunnel construction under Interstate route I-5 in Seattle, Washington, USA. The project involved removal of existing highway foundation substructures on both North and Southbound lanes as well as the underground reversible high occupancy vehicle lanes. The system utilized state of the art 3-D pulsed laser scanning, wireless sensor networks, automated robotic total stations, tilt beam sensors, narrow angle tiltmeters, and in-place inclinometers. Dedicated real time data loggers, with a web based graphical interface, provided 24/7 access to critical measurements. In addition to the instrumented sections of wall and roadway subsurface which monitored physical measurements at known points, the pulsed laser scanning allowed complete site monitoring coverage where physical sensors were not located. This data allowed post processing at any location enabling the contractor and designer to respond to unforeseen structural responses to construction. Use of the instrumentation system resulted in the early detection of wall movement, and provided feedback to the designers to facilitate construction process changes in order to minimize further movement.

Jan 1, 2010

By Gerald Verbeek, Erick Baziw

Stone columns are used in geotechnical site remediation to increase load-bearing capacity and reduce settlement of foundations. Stone columns also improve slope stability and increase the shear strength of a soil. A very challenging problem is to characterize the in-situ shear wave velocities from data acquired from Downhole Seismic Testing (DST) after the insertion of stone columns. DST is an important geotechnical testing tool for site characterization that provides low strain (<10-5) in-situ interval compression and shear wave velocity estimates, but the postanalysis of seismic data acquired from DST in the presence of stone columns is very challenging due to the resulting complicated in-situ soil conditions. To obtain the right results it is necessary to use an algorithm that incorporates source wave raypath refraction. Starting with the Normal Moveout Seismic Cone Tomographic Testing (NMO-SCTT) algorithm developed some years ago, this paper outlines the modifications and additions made to this NMO-SCTT algorithm to facilitate stone column site characterization. To dramatically reduce the optimal solution space for the estimated interval velocities the paper also described a priori conditions that are applied based on the unique nature of the stone column site conditions.

"1.0 DESCRIPTIONThis work consists of furnishing all necessary labor, equipment, and materials to install prefabricated vertical (wick) drains in the ground in accordance with the Plans and as specified herein.2.0 REFERENCED CODES AND STANDARDSASTM D4716-08 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant HeadASTM D4632-08 Standard Test Method for Grab Breaking Load and Elongation of GeotextilesASTM D4533-11 Standard Test Method for Trapezoid Tearing Strength of GeotextilesASTM D4491-99a Standard Test Methods for Water Permeability of Geotextiles by Permittivity (2009)ASTM D4751-04 Standard Test Method for Determining Apparent Opening Size (A.O.S.) of a GeotextileASTM 6918-09 Standard Test Method for Testing Vertical Strip Drains in the Crimped Condition3.0 QUALIFICATIONSThe Contractor shall have successfully completed a minimum of five wick drain installation projects in similar ground conditions, and installed not less than 5,000,000 linear feet (1,525,000 linear m) of wick drain in the past five years. The Contractor shall have a minimum of five continuous years of wick drain installation experience."

Jan 1, 2014

By Maral Papazian Bedian

"Case 2. 100th Street Bus Depot: Elimination of Deep Caissons in Favor of Spread FootingsThe PROJECTThe 100th Street Bus Depot is a new five-story bus terminal for the New York City Metropolitan Transit Authority occupying one city block in Manhattan between 99th and 100th Streets, and between Lexington and Park Avenues. It replaces a former two-story garage, built in the 1890’s and initially used as a trolley-car barn. The new structure is a steelframed building with concrete floors and includes a partial basement near its middle. The easternmost column line with design loads of 10 MN (1,125 tons) is within 1.5 m of the underlying multi-tube Lexington Avenue subway system. To support the new columns along the subway line, the project bid plans had called for 1 m diameter and 17 m deep drilled shafts. The upper 14 m of each unit would have required 50 mm separation from the surrounding rock to prevent stress from being imposed on the roof and walls of the adjacent tunnel. The column loads were thus transferred to below the base of the tunnel and supported by 3 m long sockets in bedrock. The bid documents contained extensive test boring information, which revealed that the project site was underlain by massive Manhattan Mica Schist bedrock within just 3 m below street level. In fact, the Lexington Avenue two-level and multi-tube subway had been tunneled through this rock circa 1910, leaving an about 6 m thick solid roof over the upper-level subway. The NX rock core recovery values were near 100 %, with average RQD of 75 %.The CHANGEThe Bus Depot project was let as a design/build contract with a very aggressive fast-track schedule. Both the pre-bid preliminary design and the subsequent final design by the Contractor’s own hired design engineers relied heavily on very restrictive codes, including unnecessarily conservative approaches to seismic design. Any suggestion for value engineering change was undesirable and was strongly resisted. Yet, objecting against the blind reliance on codes in foundation design, the author questioned the real need for the deep drilled shafts to support the columns along the subway. The unsupported statement that no stresses from the new structure can be imposed on the roof and walls of the adjacent tunnel was not sufficient reason for the drilled-shaft design. Unconvinced that deep shafts were necessary, the author rushed to MTA’s warehouse where many rows of rock core boxes were neatly stacked. Careful inspection and some simple testing of the rock cores with the blows of a geologic hammer gave support to the reservations about the design. Later, as expected, the schist bedrock at this site was found to be hard to very hard with unconfined compressive strength values estimated to range from at least 70 MPa to over 100 MPa (10,000 psi to 15,000 psi). The tensile strength of the rock was assessed to be minimum 5 MPa (750 psi)."

Jan 1, 2003