Search Documents

By Lorne Roberts

"This paper describes: how Falconbridge's fire protection system meets the needs of the Lockerby Mine; why the system was chosen over other alternatives; how it is unique, but can be applied to any underground situation; details of the system; how it was installed; the role of a fire protection company; and general considerations when choosing afire-suppresant system.IntroductionIn May 1981, after about three years of searching for the best fire protection system for the re-opened Lockerby nickel mine at Whitefish, near Sudbury, Ontario, Falconbridge Nickel Mines Ltd. installed an AFFF type of fire suppression system. It was designed and supplied by the Fire Protection Systems Division of Levitt -Safety Ltd.The system protects against loss of life, equipment and/or production, and it complies with legislation should fire occur in a fuel storage area and/or scooptram garage and service bay at any or all of the three levels near Shaft No.2.About 18 months after Levitt-Safety began working with Falconbridge, the system was designed and installed at a cost considerably less than that which would be incurred if fire damage caused the loss of two days of production.The fire protection system, which overcomes a limited water supply, is a self-contained balanced pressure proportioning system. It senses the flow and automatically determines the correct concentration of foam to water. It is triggered by a release mechanism which operates a bank of nitrogen cylinders, which in turn pressurize a pressure vessel to expel the foam concentrate and water from the tanks. This solution is piped to sprinkler heads in the specific area."

Jan 1, 1982

By Philippe V. Scheers

Polycrystalline gold, glassy carbon and gold-activated glassy carbon electrodes were compared for the production of hydrogen peroxide by the cathodic reduction of dissolved oxygen. Gold was deposited on glassy carbon by sputtering with a sputter coater and by electrodeposition from a diluted KAuCl4 solution using short potential steps. The sputtered gold particles were not adherent enough, but there were no adhesion problems with the electrodeposited gold particles. The gold coverage of the glassy carbon surface could be varied by applying a different number of potential steps. The overpotential for the electroreduction of oxygen to hydrogen peroxide decreases with increasing gold coverage of the glassy carbon surface, and for gold coverages exceeding about 16 %, the overpotential is close to that observed on polycrystalline gold.

Oct 1, 2003

By K. D. A. Whaley

Abstract -The Captain North Extension deposit consists of five sulfide lenses hosted in cherty and chloritic metasediment that is bounded by quartz-eye rhyolite and laminated rhyolite . Lens 2 consists of sphalerite and galena with silver-rich tetrahedrite in chert. Lens 3 contains massive pyrite, with chalcopyrite and minor gold, gradational to minor pyrite in a chloritic metasediment . The other lenses are unexplored. The sulfides occur as beds, fracture infills, and disseminated grains. Reserves are estimated at 207 555 tonnes grading 7.38% Zn, 2.76% Pb, and 91.81 g/t Ag. The deposit is isoclinally folded, dips steeply west, plunges 50 degrees south, and is faulted out to the north, where drag folding has reversed the plunge. Minor cross-faults contain talc and sericite. High sphalerite but low pyrite abundances result in poor responses to standard electromagnetic techniques. Lens 3, which contains more pyrite than Lens 2, responds better to induced polarization and allows detection. Geochemical anomalies are found in a nearby swamp and stream, but an impervious till cover inhibits the development of soil anomalies.

Jan 1, 1992

By The Staff

"A general description of the equipment, personnel and work sequence •being used in the sinking of a circular, concrete lined, 14 foot diameter shaft which at present is at a depth of 2,484 feet. Equipping, lining and sinking of the shaft is being carried out concurrently and waste is re-moved using a mechanical mucker.INTRODUCTIONTHE BUCHANS UNIT of the American Smelting and Refining Company operates a group of mines at Buchans, Newfoundland. Buchans is in the centre of the Province (Lat. 48°47'N.; Long. 56°50'W.), five miles north of Red Indian lake at an elevation of 900 feet and is accessible by 37 miles <Jf private railway which connects with the Canadian National railway at Millertown Junction, and by 47 miles of gravel highway, which connects with the Trans-'Canada Highway at Badger."

Jan 1, 1959

By Phillip J. Mackey, Susumu Okabe

Copper mining and smelting has been carried out in Japan for over 13 centuries and in fact stretching back into antiquity. In 1889, the first electrolytic copper refinery in Japan based on Elkington’s principles was started by Furukawa Mining at Honjyo in downtown Tokyo based on the multiple or parallel system. Within two decades, a number of other copper refineries had begun operation. Interestingly, but perhaps not surprising given Japan’s long history of copper production, this first refinery in Japan commenced just ten years after the first refinery in the USA (1879), and not long after the first plants in Europe. By 1935, as a result of growth in copper demand, there were six domestic copper electro-refineries in Japan with an installed capacity of 97,800 tonnes/a, while actual production was 71,200 tonnes/a. Since about 1932, the majority of these plants were based on the more common parallel or multiple system. In 1946, just after World War II, domestic production capacity had dropped considerably to 29,000 tonnes/a, however with reconstruction, capacity and production expanded rapidly, with production reaching 81,000 tonnes/a in 1955, 187,000 tonnes/a in 1960 and 307,000 tonnes/a in 1965. The introduction of the first refinery and the early ones that followed and subsequent developments are discussed in this paper. The major technical achievements during the high growth period from 1945 to 1963 included: the use of fire- refined anodes; the introduction of newly-developed rectifiers; the introduction of lead-lined or vinyl-lined concrete cells; improvements in the electrolyte heating system; application of improved anti-corrosion materials and the introduction of heat-insulating surface coverings. In 2018, Japan’s refined copper production totaled 1,595,000 tonnes of copper, with Japan ranking third in the world after China and Chile. INTRODUCTION In 2018, Japan’s refined copper production totalled 1,595,000 tonnes of copper and Japan ranked third in the world for refined copper after China and Chile (Wood Mackenzie, 2019). There are now eight copper refineries in Japan which provide Japan’s production of refined copper. These plants are listed in Table 1 (Wood Mackenzie, 2019), also showing the production trend since 2013; in general, production over this period has been relatively steady. The Toyo plant is now the 7th largest copper refinery in the world after several large plants as rated by capacity in China, Russia and India (ICSG, 2019).

Jan 1, 2019

By D. R. Spink, G. L. Rempel, C. O. Gomez Bueno

"A morphological and chemical study of the Great Canadian Oil Sands Ltd. (GCOS) fly ash has been carried out. Extensive scanning electron microscopy, as well as light microscopy, showed that the GCOS fly ash consists of two fractions, one composed of unburnt or partially burnt irregular-shaped carbon particles and an ash fraction composed of transparent and opaque, often coloured, glassy spherical particles-some of them cenospheres (hollow spheres) and the others plerospheres (hollow spheres packed with smaller spheres). Microcrystals (0.1 to 0.3 um long) growing on the inner and outer surfaces of some of the spheres were also noted and found to contain more Fe, Ti, Ni and V than the spheres.The carbon-free GCOS fly ash particle size follows a lognormal distribution, with a geometric median particle size (by count) of3.8um and a geometric standard deviation of 1.84. IntroductionCanada&apos;s current energy situation strongly suggests that oil from the Alberta tar sands deposits will probably be recovered more extensively in the future. Today&apos;s commercially proven technology to recover oil from the Athabasca tar sands, as practised by Great Canadian Oil Sands Ltd. (GCOS), involves two major operations, namely: separation of the bitumen from the sand and upgrading of the bitumen to refinery oil; the production of significant amounts of petroleum coke and sulphur during the bitumen upgrading process. The bulk of the petroleum coke is burnt in boilers to fulfill the energy requirements of the entire operation. The boiler ash, which contains appreciable amounts of metals, such as vanadium, nickel, titanium, iron, aluminum and other elements, is collected in the boiler hoppers and cyclones of the petroleum coke-fired steam generation plants. Thus, as well as representing a petroleum resource, the tar sands represent a resource for vanadium and possibly other metals providing that metal recovery processes can be developed."

Jan 1, 1980

By P. R. Brito-Parada, G. Bhutani

"The physical processes occurring in flotation columns are very complex as they take place at different scales over a range of sizes and multiple phases. Column design and optimum operating parameters are usually obtained from empirical studies and although progress has been made on its numerical modelling, most column models rely on simplifications that do not fully capture the hydrodynamics. In particular, Computational Fluid Dynamics (CFD) models of the pulp phase in flotation usually assume the bubble population to be monodispersed. While this assumption may be reasonable in some situations, the polydispersed nature of the gas phase can have a significant impact on the predicted flotation rates.Techniques to model size distribution do exist in the literature and have been rigorously analysed in the past two decades for bubble columns, which are very similar to flotation columns from a hydrodynamics point of view. In fact, available CFD models of flotation columns are an extension of bubble column models, sometimes including additional equations for solids treated as passive scalars. This work focuses on the development of an efficient CFD model for flotation columns. The bubble size distribution in the column has been modelled using the Population Balance Equation (PBE), which is solved using the Direct Quadrature Method of Moments (DQMOM). Coupled with the PBE, the multiphase flow equations in the column have been modelled using the standard Eulerian–Eulerian approach. The solution of this coupled system has been made tractable in this work with the implementation of a highly parallelised adaptive-mesh finite element method. This powerful framework has been implemented in the open source CFD code Fluidity and it allows the carrying out of detailed simulations of flotation columns in 2D and 3D, with important implications for industrial column evaluation and design."

Jan 1, 2016

? Introduction ? Partenariat MRNF - MAE ? Goldex ? Manitou : - Ré-aménagement du bassin versant - Accès aux zones problématiques - Filtration du ruisseau pour les travaux - Nettoyage près de la rivière - Régulation du débit et bassin - Digues et bassins - Déposition résidus Goldex ? Chemins d?accès Goldex-Manitou ? Pipelines: Goldex ? Retour Goldex ? Manitou ? Station de pompage ? Résumé

Feb 1, 2008

By Andrew J. Neale, Brian C. Flintoff

"In most mineral processing operations the term ""audit"" is usually reserved for the exercise of checking financial records and/or safety practices. While these activities are time-consuming, no one disputes their necessity or value. If these areas are subjected to such careful scrutiny, why is it that the same principles are not normally applied to critically examine process operation. After all, the operating efficiency of the plant impacts directly on the measures of profitability.A mineral processing plant is a complex system that has a number of distinct, but mutually dependent elements: process equipment, instrumentation, operating policies, maintenance policies, control strategies and people. To ensure maximum economic performance in the dynamic environment that characterizes a concentrator, requires a periodic review of each of these areas. However, to be useful, the study must be based on sound metallurgical principles and be conducted in a highly focussed manner. Experience has shown that the exercise is very revealing and rewarding.This paper will discuss the plant audit process and illustrate its potential value through examples taken from plant studies."

Jan 1, 1992

By A. L. Holloway, N. M. Soonawala, L. S. Collett

"Since the late 1970s, a major R&D program has been under way in Canada to assess the concept of disposing of nuclear fuel wastes in deep plutonic rock. Atomic Energy of Canada Ltd . (AECL), a federally-owned corporation, has been given the responsibility of directing this research (Rummery et al., 1983).The Underground Research Laboratory (URL), constructed in a granite pluton 15 km east of Lac du Bonnet, Manitoba (Fig. 1) is a major component of the Canadian Nuclear Fuel Waste Management Program. A diverse geotechnical experimental program is being carried out during both the construction and operating phases of the URL. This program involves detailed geological mapping, rock mechanics and hydrogeology studies, and geophysical surveying, to characterize the rock mass surrounding the shaft, and it has been described by Simmons et al. (1983). As part of the construction-phase program, ground-penetrating radar (GPR) surveys are being carried out during excavation, in an attempt to delineate fractures both ahead of the excavation and behind the walls of the excavation. This paper presents the results of surveys performed during shaft excavation and describes a procedure for plotting the data.Ulricksen (1982) cites examples of radar surveys to evaluate surficial deposits, such as peat, sands and gravels, and cavity detection in subsurface hard rock. Fowler (1981) used radar for fracture and clay vein detection in coal seams.In Canada, pioneering work in GPR has been done by Annan and Davis since the mid-seventies (Annan and Davies, 1976). Their work concentrated on problems relating to permafrost in the Arctic ."

Jan 1, 1986

By A. I. A. Salama, M. W. Mikhail, R. J. Mikula

"The Coal Research Laboratory (CRL) of CANMET along with other research organizations in coal-producing countries envisage major benefits from computer applications in coal preparation, Some of these benefits are greater system flexibility, improved coal preparation plant performance efficiency and efficient utilization of manpower, all of which result in economic benefits. Computers can be applied for both on-line and off-line purposes; this paper focuses on the on-line applications from the process control point of view.A critical discussion of the different analog and digital process control systems is presented. Recent developments in Great Britain, West Germany, Poland and Australia on automation and instrumentation using on-line measurements of coal ash and moisture contents are identified.The CRL research and development strategy aimed at achieving on-line computer control of an automated coal preparation plant is presented.IntroductionIn the past twenty years an enormous progress in the area of computer technology has been noticed. Computer applications in industrial processes offer greater system flexibility, improved plant performance efficiency and efficient utilization of manpower. Significant computer control development in mineral processing has already been achieved. Although progress has been made in the area of computer applications in coal preparation, more effort is needed to utilize the full potential.The computer applications in coal preparation can be viewed as off-line and on-line. Considerable progress has been reported in the area of off-line computer applications, especially in the areas of modelling, performance evaluation/prediction and statistical analysis. However, only modest progress in on-line applications has been reported(1-7). This paper will focus on: online instrumentation and process control applications, different analog and/or digital control systems, on-line automation and instrumentation in other countries and CRL strategy toward pilot plant automation."

Jan 1, 1985

By J. Oliveira, A. R. Barnes, R. Pandher

Sub-stoichiometric roasting of arsenic-bearing copper ores is a well established practice. However, ores containing calcium commonly prove challenging where very low arsenic levels are desired, but the reasons for this phenomenon have largely been speculative. In the course of treating arsenicbearing copper ores by partial roasting in fluid bed reactors, XPS encountered one of these Ca-bearing ores which proved a challenge to roast to acceptably low levels of arsenic. Mineralogical examination of the calcines using a combination of XRD (X-ray diffraction), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro-Analysis) helped to identify the arsenic bearing species and assisted in developing a workable theory on the sequence of reactions occurring during the roast. With the assistance of thermo-chemical modelling, this allowed adjustment of the roasting conditions to minimise the amount of arsenic retention in the calcine in spite of the presence of calcium in the ore and advance the roasting program to a commercially acceptable solution.

Jan 1, 2014

By R. P. Mahant

"Extensive pilot plant investigations were conducted both on partial roasting an d electric furnace smelting from September 1973 to August 1975.The objectives of the pilot plant investigations were:(I ) to confirm the application of available process technology to treatment of Falconbridge concentrate.(2) to examine partial roasting variables.(3) to investigate electric furnace smelting of roaster calcines .(4) to develop process design and operating parameters for a commercial plant.This part of the paper will cover the following topics:Partial Roasting InvestigationsPilot Electric Furnace InvestigationsPartial Roasting InvestigationsThe specific objectives were to:1. establish process variables for maximum oxygen efficiency and bed fluidi ation.2. determine the product distribution between the roaster and the various gas cleaning stages.3. produce a mass and thermal balance."

Jan 1, 1984

By Wojciech Naworyta

The development of the Gubin lignite deposit, located in western Poland is the first mining investment of this magnitude in 30 years. Gubin is the second largest prospective lignite deposit in Poland, with over one billion tonnes of indicated reserves, which would be sufficient for a 2700 MW power plant for almost 50 years. The paper presents select problems related to the mining development of Gubin deposit. Attention has been paid to changes in legal and formal requirements for mining investments that were introduced after the change of Polish social and economic system. The significance of spatial, environmental and social conditionings has been emphasized. Typical attributes of the mine planning process have also been presented. Those include the long time horizon of the investment, uncertainty of external conditions and resulting difficulties in the project?s economic evaluation. Focus has been placed on mutual connections between particular elements of the project and time dependence during the process of their development. Iterative characteristics of the design process have been proven, together with resulting necessity of frequent verification of previous assumptions. As a background for presenting selected problems related to future development of Gubin lignite deposit, the methods of design have been discussed ? the variants method, the empirical method and the method of consecutive approximations. The tools and the possibilities of their use for solving specific problems related to mine design of an open pit have been broadly discussed. The chapter in which the authors relate to the specific problems of Gubin deposit development constitutes the main part of the paper. It depicts the assumptions on which the annual production and the total extraction of lignite during life-of-mine period have been based. The process of mine designing has been discussed, taking into consideration environmental, geotechnical, spatial, social and mining conditions. The criteria for choosing the location of the opening cut and the external dump have been mentioned. In the summary, the present state of mine design progress has been presented, together with some problems that will need to be solved during the next stages of the deposit?s development.

Aug 1, 2013

By Pierre Beaudoin, Michel Bourassa, Robert Lanthier, Samir Chéfaï

"Mine Doyon, in collaboration with CRM's Process Control Division, improved the control strategy at the SAG mill I Ball mill grinding circuit. The project aimed at increasing operation stability and throughput. First, a needs analysis was achieved in order to define the control philosophy and to upgrade the process control equipments and instrumentation. The stabilizing control strategy has been developed and implemented successfully using single loop PID controllers. The monitoring feature as well as the rule based supervisory control strategy were implemented on 486PCs running Process Vision and COMDALE/C softwares. Main features of the control strategy are described in this paper while results are presented and discussed.RésuméLa Mine Doyon, en collaboration avec le service de contrôle des procédés du CRM, a optimisé la stratégie de contrôle au circuit de broyage. Les objectifs du projet étaient !'amélioration de la stabilité de !'ensemble de !'opération et la maximisation du tonnage usiné. Une analyse de besoins a été réalisée pour concevoir la philosophie de contrôle et déterminer les ajouts a apporter a I 'instrumentation et au systeme de contrôle. Une stratégie de contrôle à deux niveaux, integrant stabilisation et supervision, a été developpee et mise en opération. La regulation est réalisee par une combinaison de contrôleurs Moore de type PID. Le monitoring et la stratégie de contrôle a base de règles soot implantés sur des micro-ordinateurs de type PC/486 avec les logiciels ProcessVision et Comdale/C. Les principaux aspects de Ia stratégie de contrôle sont décrits dans cet article et les résultats obtenus soot présentés et discutés."

Jan 1, 1995

By B. Nanthakumar

The impact of stockpile oxidation on chalcopyrite was studied through collectorless and collector-induced flotation conditions. In both cases, the Cu grade-recovery performance of stockpiled ore showed relatively poor concentrate grades with respect to that of a fresh sample. However, the oxidation had a minor effect on chalcopyrite recovery itself. The poor concentrate grades resulted from dilution effect primarily by excessive flotation of pyrrhotite. Size-by-size analyses indicated that for the collectorless flotation, the recoveries in the coarse and fine particle-size regions, were higher for fresh ore than for stockpile sample. A greater impact was seen in the coarse size regions for both types of sample, compared to the collector-induced case. The Cu recoveries showed a remarkable increase in the coarse size range for both samples when a collector was used. However, the case for stockpile sample was a marginally higher compared to the fresh sample. This difference has been offset by an opposite trend that was observed between these two samples in the fine size region. It is concluded that in contrast to the case with nickel-bearing sulphides, stockpiling conditions do not show a significant adverse effect on behaviour of chalcopyrite due to its strong floatability, regardless of oxidation.

Jan 1, 2007

By H. Nejati

Experimentally, the Semi-Circular Bending Moment (SCB) fracture toughness test results of Basalt Specimens Under Illumination (BSUI) have shown reduction in fracture toughness and failure force as a result of micro-cracking. The fractographic investigation of BSUI confirms initiation and extension of micro-cracks. Determination of a relation between strength reduction (herein fracture toughness reduction) and density, location and orientation of thermo-mechanical induced cracks due to microwave radiation is critically important. Numerical modeling can bridge strength reduction and the density of thermal microcracks generated due to microwave radiation. Discrete Element Modeling (DEM) is a power tool for simulation of micro-crack initiation, coalescence into macroscopic fractures and failure mechanisms in brittle rock specimens under different stress regimes (herein combination of pure tensile stress due to SCB testing, and thermal stress due to microwave radiation). For this purpose, a DEM modeling of SCB testing of basalt using EDEM (i.e., a DEM based software). DEM models are calibrated according to results of experimental SCB testing as reported in previous papers. This paper first reviews some background data on SCB fracture toughness, and experimental results of fracture toughness of microwave treated SCBs. Then it proposes a new methodology for simulation and validation of rock samples exposed to microwave illumination with regard to experimental results, and discusses the correlation between fracture toughness of BSUIs and density of micro-cracks, which is attributed to applied microwave power and duration of illumination.

Aug 1, 2013

By Peter Harben

"This paper discusses the benefits of industrial minerals, their sources of supply, price and marketing trends, and their increasing use as substitute materials and ""strategic"" minerals. IntroductionKaolin finds have yet to spark the kind of frenzy associated with the 1849 California gold rush; no dolomite deposit has ever gained the notoriety of the Comstock Lode; and few industrial minerals are counted among the currently fashionable list of "" strategic mineral s"". Nevertheless, the glamorous zhine associated with metals may be somewhat superficial; further digging provides perhaps the real foundation of modern society - industrial minerals.They are often tagged as common, everyday materials that are simply dug out of the ground, crushed and hauled to a local point of consumption. Although this description is accurate in the case of road aggregates, sand and gravel, and the like, there are many exceptions to this rule. The term industrial minerals is rather nebulous, covering as it does the mundane and esoteric, the chemically active and the refractory, the $2 and the $10m-a-ton product. All of these minerals influence every facet of modern life from fertilizers to fire retardants, ceramics to cars, construction to clothes, and toothpaste to tennis courts. Their usefulness is well illustrated by the variety of industries they serve; the main ones are listed in Table 1. It is now time to dismiss the notion of non-metallics as the ""third world"" of natural resources business after the metallic and energy products by dispelling some of the myths regarding abundance, variety and value of the group&apos;s sixty-plus products."

Jan 1, 1982

By Jean-Luc Collins

"This paper shows how simple reliability concepts such as mean time between failures and mean repair time can be used efficiently to help increase equipment availability and so reduce the economic losses associated with unreliability.More specifically, the paper shows how these simple concepts can be used in maintaining an appropriate balance between fleet failure and repair rates and how they can be used for setting up priority repair rules f or queuing equipment.IntroductionA profitable mining operation must handle large quantities of ore and waste at the lowest possible cost. To achieve this objective, the operation must optimize the productivity of its fleets of equipment by efficient management of the time element. Figure I shows some basic equipment activities in an open pit operation while Figure 2 shows a tree diagram describing some time elements of these activities.It should be noted that the only time a piece of equipment can generate a profit is when it can be found in the operating status. In order to maximize this time element, the sum of the other time elements must be minimized because the total time is always fixed.This paper shows the application of simple techniques capable of reducing the waiting time for repair (maintenance delay) by using simple reliability concepts."

Jan 1, 1988

By Carlos Palacios M., Brian K. Townley

"Abstract - The mainland Aysén region of Chilean Patagonia (44°15&apos; - 47°30&apos;S) is a representative segment of the South American active continental margin, distinct with respect to northern and central Chile. Mineralization consists mainly of polymetallic deposits, with important Zn-Pb mines and more recently discovered Au-Ag deposits, unlike the central Andes, which are dominated by Cu mineralization. On a regional scale, rocks may be grouped in four main map units: 1) the Paleozoic metamorphic basement; 2) upper Jurassic-Cretaceous calc-alkaline volcanic and marine sedimentary rocks; 3) the Patagonian batholith, and 4) upper Cretaceous to Miocene basalts and marine and continental sedimentary rocks. The upper Jurassic-Cretaceous rocks and the Patagonian batholith formed in a volcanic arc and back-arc setting superimposed on the Paleozoic metamorphic basement.Based on geographic location and geologic and tectonic setting, ore deposits in this region are assigned to three groups, from south to north: El Faldeo, Fachinal, and El Toqui. The El Faldeo group (south of 47°05&apos;S) includes upper Jurassic Zn-Pb skarn and associated polymetallic massive sulfide vein deposits locally overprinted by Au-rich epithermal mineralization, hosted by volcanic and sedimentary rocks and/or by rocks of the metamorphic basement. The Fachinal group (46°05&apos; - 47°05&apos;S) consists of volcanic-hosted lower Cretaceous Au-Ag epithermal deposits, except for the Mina Silva and Manto Rosillo deposits, which are metamorphic basement-hosted Zn-Pb skarns. The El Toqui group (44°30&apos; - 46°05&apos;S) comprises lower Cretaceous Au-rich Zn-Pb skarns and associated polymetallic veins, as well as Au-Ag-rich epithermal deposits, hosted by volcanic, intrusive, and marine sedimentary rocks. Galena lead isotopic signatures for each deposit group indicate a decreasingly radiogenic trend from south to north, suggesting different lead sources or differences among underlying crust. Three metallogenic provinces and two metallogenic epochs are proposed for the Aysén region: the El Faldeo metallogenic province of Late Jurassic age; and the Fachinal and El Toqui provinces of Early Cretaceous age. Résumé - La partie continentale de la région d’Aysen (Patagonie chilienne, 44°15&apos; - 47°30&apos;S), est unsegment représentatif de la marge continentale active d’Amérique du sud, différent des segments du nordet du centre du Chili. La minéralisation, qui consiste essentiellement en des dépôts polymétalliques, avec d’importantes mines de Pb-Zn, et des dépôts d’Au-Ag récemment découverts, différe de celle des Andes centrales où domine la minéralisation cuprifère. A l’échelle régionale, les roches peuvent être regroupées en quatre unités cartographiques principales : 1) le socle métamorphique paléozoïque, 2) les roches volcaniques calco-alcalines et les sédiments marins du Jurassique supérieur-Crétacé, 3) le batholite patagonien, et 4) les sédiments marins et continentaux ainsi que les basaltes du Crétacé supérieur-Miocène. Les roches du Jurassique supérieur-Crétacé et le batholite patagonien, formés dans un contexte d’arc volcanique et d’arrière-arc se superposent au socle métamorphique paléozoïque.Fondé sur la localisation géographique ainsi que sur le cadre tectonique et géologique, les dépôts de minerais de cette région se répartissent en trois groupes, du sud au nord, El Faldeo, Fachinal et El Toqui. Le Groupe El Faldeo (sud de 47°05&apos;S) contient des skarns à Pb-Zn du Jurassique supérieur associés à des veines de sulfures massifs polymétalliques, localement recoupées par des minéralisations épithermales, riches en Au, et contenus dans des roches sédimentaires et volcaniques et/ou dans des roches du socle métamorphique. Le Groupe Fachinal (46°05&apos; - 47°05&apos;S) consiste en des dépôts épithermaux Au-Ag, se trouvant dans des roches volcaniques du Crétacé inférieur, excepté pour les dépôts de la Mine Silva et Manto Rosillo, où des skarns à Pb-Zn, se trouvent dans le socle métamorphique. Le Groupe El"

Jan 1, 1999