Search Documents

By M. Sugamata

Creep tests were carried out for friction welded joints of AZ31 magnesium alloy rods under an ambient atmosphere at temperatures between 423 and 573K. Tensile tests were also performed at temperature from room to 573K. The obtained results were compared with those of the base metal. AZ31 extruded rods of 19 mm in diameter were joined by brake type friction welding machine. Creep and tensile specimens were machined out of the welded rods. The tensile strength of the joints was almost the same as that of the base metal at room temperature. However, joint efficiencies of welded joints were about 92% at above 373K. The elongation of welded joints was lower than those of base metal. The welded joints showed appreciably higher minimum creep rate and shorter rupture time than the base metal at all the tested temperatures and initial creep stresses. Creep and tensile rupture of the joints always occurred at near the weld interface. Thus, friction welded joints of AZ31 alloy showed lower creep and tensile strength than the base metal at elevated temperature.

Jan 1, 2006

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By D. R. Murray

"In 2017, Nutrien Allan Potash remediated a portion of the concrete liner in the production shaft. A set of underslung work platforms and collection boxes were used in conjunction with hydraulic splitters, jackleg drills and hand chippers to excavate and remove the broken concrete. New concrete was placed with the original pressure relief design, using a shaft slip form. Shortly after excavating, it was found that the estimated breaking rate and amount of original concrete in-situ was under estimated. Fifteen feet of excavated concrete (2719cu.ft) and ten feet (of replaced concrete was completed on April 28, 2017, and operation of the production shaft was returned to mine operations. During February 2019, Nutrien Allan Potash began remediation of a portion of the concrete liner in the service shaft. The project is different than the 2017 project, as the remediation has occurred during normal running operations and occurred only on night shift. Rather than hydraulic splitters and hand chippers, the new method includes a concrete saw and mechanical excavator from a working platform. The selected method is based on the lessons learned from the 2017 project in the production shaft. The service shaft project was scheduled to be completed in July, 2019. INTRODUCTION Nutrien Allan Potash is located approximated 75 km east of the city of Saskatoon, Saskatchewan, Canada. There are currently two shafts at Nutrien Allan Potash: the Production Shaft and the Service Shaft, transporting people and material from surface to a depth of 3,335 ft. The Production Shaft was completed in 1967, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1605 and 2037 ft Levels. A second set of cast iron tubbing was installed in the Duperow formation between 2203 and 2463 ft Levels in 1999. The remainder of the concrete as of todays standards is designed as a pressure relief liner. The Service Shaft was completed in 1968, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1600 and 2048 ft Levels. A second set of cast iron tubbing was installed in 1981, with 169 ft installed through the Duperow formation. The remainder of the concrete as of todays standards is designed as a pressure relief liner. PRODUCTION SHAFT REMEDIATION During the second quarter of 2015, the Mine Engineering team were notified of an area of concern in the production shaft. The shaft specialists of Golder Associates Ltd (Golder, formerly Alan Auld Canada) were contacted to complete an inspection of the production shaft liner with emphasis on the area of concern. Based on the inspection and documentation review, it was determined that the concrete at the 2804 foot elevation had been broken out for some time and was retained with #8 rebar bolts with resin encapsulation. The broken concrete was encroaching on the clearance to the conveyance."

Jan 1, 2019

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By N. Kubo

Sumitomo Toyo Copper Smelter and Refinery was commenced in 1971, and its production capacity of sulfuric acid was 550tpd at the beginning. In 2001 Toyo Copper Smelter and Refinery projected to expand its copper production capacity to 450,000tpy, and now the project is still in progress. To achieve this expansion project, 4,000tpd of sulfuric acid production capacity is necessary to the acid plant. So as a part of this project, the construction of the new converting and absorbing line and the improvement of the existing converting and absorbing line were carried out from 2001 until 2005. Then the production capacity of these 2 lines has already reached the target, 4,000tpd of sulfuric acid. Moreover, at the design of the new line, we adopted several latest technologies and materials in order to construct the world's leading acid plant. Basing on the operation performance of the new line, we have improved the existing line in 2005. Both of these 2 converting and absorbing lines are working quite well and contribute to big energy saving and excellently stable operation. Cu2007

Jan 1, 2007

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he's hurt. Maybe he's not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

Oct 1, 2010

By John H. Fowler

Nova Scotia has been mining and exporting industrial minerals for over two hundred years. As an industrial mineral producer, this province continues to rank as the number one gypsum mining and exporting region in North America. Mining of many other commodities is ongoing, supplying many local and export markets. In all, excluding aggregate producers, there are nineteen industrial mineral producers operating at thirty sites producing nine commodities including anhydrite, barite, clay and shale, dolomite, gypsum, limestone, salt, silica sand and stone (Fig. I). Numerous aggregate producing operations supply all the province's aggregate requirements and export some of these materials to other regions of Atlantic Canada and as far away as Bermuda (Fig. 2) . Production value of industrial mineral commodities in Nova Scotia for 1982 was $105 million , representing 39% of the total value for all mineral production for the year. Because of the general improvement in the economy, indications are that the 1983 value of production will be higher.

Jan 1, 1984

By P. Langlois, G. Labonté, J. J. Barrett, J. Holmes

"The Voisey’s Bay mill processes a high-grade pentlandite and chalcopyrite ore in a largely pyrrhotite/troilite matrix. From 1994 to 1997, circuit development focused on making a 14% nickel concentrate. When flowsheet development resumed in 2001, the target grade was raised to 20% ni. initially triethylene tetramine and sulfite pyrrhotite depressants were used in a lime circuit, but by recycling process water and the contained thiosalts, the required nickel grade was made without depressants. construction of the mill was fast-tracked, with start-up in september 2005. ramp-up was faster than other recent nickel installations, with tonnage being limited by concentrate dewatering due to higher-thanexpected ore grades.RÉSUMÉ l’usine de traitement de Voisey’s Bay traite un minerai à teneur élevée en pentlandite et chalcopyrite dans une matrice formée surtout de pyrrhotite/troïlite. De 1994 à 1997, le développement du circuit ciblait la production d’un concentré à 14 % de nickel. lorsque le développement du schéma de traitement a été repris en 2001, la teneur cible a été élevée à 20 % de ni. initialement les déprimants triéthylènetétramine et sulfite de la pyrrhotite étaient utilisés dans un circuit à la chaux; cependant, en recyclant l’eau du procédé et les sulfosels qui y sont contenus, la teneur en nickel a été atteinte sans utilisation de déprimants. la construction de l’usine de traitement a été accélérée et elle a démarré en septembre 2005. la mise en opération a été plus rapide que pour d’autres installations récentes de nickel; le tonnage traité étant limité par le séchage du concentré en raison des teneurs de minerai plus élevées que prévu."

Jan 1, 2017

By M. E. Holter

"Limestone-bearing strata are exposed in seven areas of Alberta, each situated adjacent to rail and road facilities. Six of these centers are located along the eastern edge of the Foothills and Front Ranges of the Rocky Mountains in western Alberta. The other is in northeastern Alberta, along the eastern margin of the Alberta Basin. High-grade limestones are present in Middle Cambrian, Upper Devonian and Mississippian strata. Middle Cambrian (Eldon Formation) limestones have been exploited only in the Exshaw area west of Calgary, where they formerly were used for lime production. Limestone beds of the Upper Devonian Palliser Formation are exploited at Exshaw and at Cadomin in west-central Alberta for the manufacture of cement. Reserves of high-grade limestone also are available in the Palliser Formation near Crowsnest Lake in southwestern Alberta and near BrUle, west of Edmonton. Upper Devonian limestones of the Waterways Formation are widespread in the Fort McMurray area of northeastern Alberta, but available data indicate they are of inferior quality to the limestone deposits of the Rocky Mountains regions. The Mississippian Livingstone Formation contains large reserves of high-grade limestone at several localities in the Rocky Mountains and Foothills. Commercial development of the unit is now underway at Crowsnest Lake and at Exshaw for lime production, and future exploitation of these beds is feasible at Blairmore and Nordegg."

Jan 1, 1973

By Wm. D. Jr. Sheldon

THIS paper presents practical data to aid in the selection of a mine ventilating fan, and outlines considerations to be made to ensure satisfactory operation and optimum efficiency of the fan. Much has been published on the general subject of mine ventilation, but the writer has found few specific data on factors and considerations which govern the selection of a fan-data which should be available to the operator if his fan is to give satisfactory service within the range of the high-efficiency portion of its performance curve and deliver the specified air capacity when operating against the anticipated range of resistance of the mine. The total quantity of fresh air furnished by the ventilation system must be adequate to provide, and to ensure at all times, safe and healthful working conditions in the mine. It is assumed that the mine operator is able to determine the air quantities required for the various parts of the mine.

Jan 1, 1941

By O. Hungr, V. Gischig, G. Preisig

Deep-seated landslides are characterized by slow time-dependent movements induced by constant gravitational creep, and periods of acceleration associated with stress changes within the rock and the preexisting fracture network. Natural stress changes are typically caused by seasonal variations in surface temperatures and groundwater pressures, but also by rare and more violent events such as earthquakes. These processes are responsible for cyclic loading and unloading that leads to rock mass damage, fatigue and progressive failure with time, and may explain sudden, unexpected rock slope acceleration phases. In this work, we present a set of distinct-element models to investigate and compare the role of hydromechanical fatigue and seismic fatigue in the history of a deep-seated landslide. Hydromechanical fatigue arises from the fluctuation of pore pressure in fractures accompanying periods of significant groundwater recharge. In alpine areas, there are usually one or two cycles per year associated with snow melt and intense rainfall periods. In the presence of a deep confined aquifer within the rock slope, the amplitude of pressure fluctuations may reach values of 0.25-0.5 MPa. Hydromechanical models considering such pressure changes are able to reproduce observed slope accelerations-decelerations phases. Substantial accelerations may occur even in the absence of a cycle of exceptional amplitude, depending on the current state of fatigue. At a given time, one or more fractures may be critically-stressed, and a small change in applied stress is enough to cause local failure and induce a crisis of enhanced slope acceleration. This is augmented if the rock slope contains planes of weakness associated with its tectonic history, glacial debuttressing, etc. The corresponding behaviour is analogous to laboratory experiments on rock and metal fatigue. Similar fatigue effects have also been proposed for repeated earthquake events in seismically active regions. Unlike hydromechanical stress changes that occur in a more localized portion of the rock slope, those induced by passing seismic waves involve the entire rock mass. Moreover, the frequency and amplitude of stress perturbations due to earthquakes are different than those induced by pore pressure variations, although both likely contribute in combination to the degradation and progressive failure of large deep-seated landslides when both are present. The results presented illustrate that: (1) assessment of slope stability near critical infrastructure (e.g., hydroelectric reservoirs) should not only consider static stability, but also failure mechanisms related to fatigue that evolve over time and may result in an apparently stable slope progressing towards a critical state due to relatively small but repetitive stress changes; and that (2) characterization of fatigue processes affecting a deep-seated landslide requires multiparametric continuous monitoring at different observation points.

Jan 1, 2015

By B. R. Bowerman, W. J. Thoburn, M. J. Humphris

"Nickel granules are produced for carbonylation by pouring a molten stream into a path of high pressure water. Granules and water are separated in dewatering bins. The overflow, which contains up to 0.1 weight percent solids, was initially cooled and recycled to the granulating step. However, the rate of buildup of these solids in the handling system was intolerable. A lamella thickener was installed to solve the problem by removing solids from the dewatering bin overflow. Its description, application and performance to date are discussed.The lamella thickener treats a slurry containing about 0.1% solids of which about 30 weight percent is less than 325 mesh. It recovers 80 to 90 percent of the input solids in an underflow slurry containing 90 weight percent solids. Since its installation the frequency of cleanout of the recycle water handling system has dropped from about once per month to about once or twice per-year."

Jan 1, 1977

By T. R. Eger

Miners can be exposed to whole-body vibration (WBV), when sitting or standing to operate mobile equipment. In order to prevent vibration-induced injury it is important to understand how miners can be exposed to vibration, the health risks associated with vibration exposure, methods to evaluate vibration exposure, and strategies to reduce vibration exposure. WBV exposure typically occurs when operating mobile equipment, such as a load-haul-dump vehicle, haulage truck, or dozer. The probability of health effects such as low back pain, neck pain, headaches, and gastrointestinal track problems occurring from daily vibration exposure can be determined based on criterion values published in ISO 2631-1 and EU Directive 2002/44/EC. A special case of WBV termed foot-transmitted vibration (FTV) occurs when a miner is exposed to vibration that travels through the feet. FTV typically occurs when standing on vibrating surfaces associated with the operation of locomotives, jumbo drills, bolters, or raise platforms; however, there is no set standard to evaluate health effects associated with FTV. Recent medical evidence confirms workers exposed to FTV can develop cold induced blanching of the toes, in addition to numbness and tingling in the feet and toes. In order to reduce the risk of adverse health effects from exposure to vibration, the hierarchy of controls (elimination; substitution; engineering; administration; and personal protective equipment) should be followed. Best practices should be used to minimize vibration exposure through equipment purchases (i.e. vehicles with lower vibration emissions and seats that attenuate vibration), reduced driving speeds, and improved road maintenance for example. The elimination of other risk factors, which increase injury risk when combined with WBV exposure, such as awkward working postures, should also be eliminated. Very little is known about FTV exposure therefore further research is required in order to develop exposure standards and identify prevention strategies.

Aug 1, 2013

By R. Erpelding

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By L. St-Georges

In aerospace and transportation industries, severe problems are related to fatigue failure. Aluminium is frequently used in these industries to optimize the solidity and minimise the weight of the structures. Nevertheless, the fatigue life of aluminium alloys is limited and specific efforts have to be made to reduce the vibratory stresses in the mechanical parts. When riveted, the life of the sheet metal structures can be increased compared to welded structures, due to the energy dissipated by the friction between the rivets and the sheet metal and the sheets themselves. In the past decade, a new tool was developed to assemble aluminium structures; the friction stir welding. With this new technique, fatigue life of the aluminium welded joints can be increased by a factor from two to ten. However, less energy can be damped by the friction between the components and increased vibratory stresses may occur. In this investigation, the potential of the friction stir welding to create damped aluminium sheet metal structures is evaluated.

Jan 1, 2006

By J. Warner, K. A. Hughes, P. E. R. Blanchard, J. Esslifie-Dughan, J. W. Reid

Tailings management plays an important role in reducing the environmental impact of Orano Canada’s uranium mining operations in Northern Saskatchewan. Uranium ores mined from Northern Saskatchewan are often associated with large amounts (10-20 wt%) of other harmful elements, such as arsenic and nickel. The JEB Tailings Management Facility (TMF) located at McClean Lake, Saskatchewan is designed to prevent potentially harmful water-soluble elements, particularly arsenic, from contaminating the surrounding environment by promoting the formation of water-insoluble minerals. It is therefore important to determine which arsenic-containing mineral species are present in the TMF and how they evolve over time. Researchers at the Canadian Light Source (Saskatoon, Saskatchewan) were successful in identifying the arsenic mineral species present in tailings samples collected from the TMF in 2013 using X-ray absorption near-edge structure (XANES) spectroscopy. XANES analysis verified that the majority of arsenic species in the TMF existed as amorphous and crystalline ferric arsenates with minor amounts of arsenite and arsenide species. Herein, XANES is again used to analyze a new set of tailings samples collected from the TMF in 2018, specifically focusing on the difference in the distribution of arsenic species in old and new tailings.

Jan 1, 2020

By Junhyun Choi, Allan Gomez-Flores, Chonbuk National University, Siyoung Q. Choi, Gahee Kim, Seungkon Kim

In this study, to confirm the effect of depletion attraction on the flotation, we theoretically and experimentally investigate the effect of the depletion attraction force on flotation. While varying the concentration of the depletion agent (polyethylene glycol), three different systems are studied: pure malachite, pure silica, and a 1:1 mass ratio of malachite and silica binary system. We find that recovery increases significantly as the concentration of the depletion agents increases for all three systems, as the depletion agent facilitates the adsorption of the particle on the bubble surface. However, the recovery suddenly decreases in a certain concentration range, which corresponds to the onset of the decreased surface tension when high concentrations of the depletion agent are used. This non-monotonic overall recovery trend implies the surface adsorption of the depletant on a surface. The decreased surface tension of the air/water interface suggests that the recovery rate is lowered due to the adsorption of the depletion agent to the bubble surface, acting as a polymer brush. Based on our observations, we conclude that the depletion force can greatly improve particle adsorption, as predicted in the accompanying theory paper, while simultaneously the adsorption of the depletion agent on the bubble surface plays an important role because it hinders particle adsorption. We also perform experiments in the presence of a small amount of a collector, sodium oleate. An extremely small amount of the collector leads to the increase in the overall recovery, which eventually reaches nearly 100 percent. Nevertheless, the grade worsens as the depletant provides the force to silica particles as well as target malachite particles.

Jan 1, 2016

By V. Labiouse, M. Souley, N. Lafrance, C. Auvray

"Chalk rocks have been used for centuries as a strong building material and for the production of lime. The shallow underground room-and-pillar quarries where the chalk was extracted are now abandoned and endure the effects of time and weathering, increasing their risk of collapse. The risk of instability, involving natural or anthropic underground structures, is an issue for more than 10 000 towns in France.In order to investigate the causes of underground quarry collapse and to aid prevention strategies, we carried out a study of the physico-mechanical behaviour and ageing of chalk in abandoned pillars in two underground quarries, in situ-instrumented by INERIS, in the Parisian Basin, France. Core samples were drilled horizontally from pillars in the Saint-Martin-Le-Noeud dolomitic chalk quarry (Oise, France) and the Estreux glauconitic chalk quarry (Nord, France).Uniaxial tests were performed on dry and saturated cylindrical plug samples extracted perpendicular to the cores at regular distances along their lengths. Physical and mechanical properties were obtained. The dolomitic chalk (Saint-Martin-Le-Noeud) exhibits variation in mechanical and physical properties with horizontal pillar depth. Both density and compressive strength seem to increase outwards from the pillar-core to the pillar-wall. This is the opposite of that would be expected from a purely mechanical point of view. SEM analysis revealed progressive degradation and homogeneity of the grains from the edge to the inside of the pillar. At the pillar wall, the crystal faces are well-defined, almost euhedral, and the grains are of variable size. In contrast, at the inside of the pillar, crystals are finer-grained and are anhedral with highly degraded edges. In the physico-mechanical tests and SEM analyses performed on the Estreux samples, no significant variation was observed between the pillar-walls and pillar-core. However, dissolution marks were observed along the entire length of the half-pillar core."

Jan 1, 2015

By J. R. Rodda

Stainless steels are widely used to handle concentrated sulphuric acid (H2SO4) solutions produced in the manufacturing process, The majority of corrosion rate data published for stainless steel in product acid conditions is typically complied in tables or in iso-corrosion diagrams (iso-corrosion rates plotted as a function of temperature and H2SO4 concentration), without any reported consideration as to the accuracy and relevance of the method used to obtain the data, Given the characteristic potential cycling associated with the active-passive corrosion behaviour exhibited by stainless steel in hot, concentrated H2SO4, weight loss is considered to be a more reliable method than electrochemical measurements to measure corrosion rates, Consequently, an effort is made herein to demonstrate the accuracy and relevance of weight loss to determine laboratory corrosion rates in product acid conditions.

Jan 1, 2010

By J. M. Wetherill

"This paper presents the results of an investigation into the level of radon, as against the natural background, at the Vicary Creek coal mine in Alberta. The concentrations of radon and daughter products detected in the mine were considered to be insignificantly higher than the concentrations of naturally occurring radon and thus do not constitute a health hazard to the miners.INTRODUCTIONTHE HIGH INCIDENCE OF LUNG CANCER among miners exposed to radon was established some thirty years ago. The presence of this gas in mines is primarily associated with pitchblende extraction operations, al-though coal contains detectab`e quantities of U30s. A previous study bas shown that coal from southwestern Alberta (Exshaw and Banff) contains lower than average concentrations of this element (1).As part of a general investigation into the occupational health environment of coal miners in Alberta, field measurements were made to establish the level of radon and to investigate the natural background radiation in the Vicary Creek coal mine, located some 16 miles north of Coleman, Alberta, on the easternmost slopes of the Rocky Mountains."

Jan 1, 1968