Search Documents

By Narasimha Mangadoddy, Balraju Vadlakonda

"Bubble size distribution, bubble rise velocity and gas and solids hold-up are the key major hydrodynamic parameters that are extensively used for column flotation design and performance evaluation. The distribution characteristics of mean gas hold-up is studied using electrical resistance tomography (ERT) coupled with pressure transducers (PT) in column flotation. The ERT technique facilitates non-invasive and nonintrusive visualization of different flow regimes even in the presence of particles in a column flotation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas hold-up and its radial distribution has been analysed for both two-phase and three phase flows. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the three-phase flow hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, are employed to explore the influence of parameters in two phase flow in column flotation. Mean gas and solids hold-up values extracted from ERT have been critically analysed for the column operating in various flow regimes. Gas hold-ups and solid hold-ups results using ERT are in very good agreement with conventional estimation and correlations obtained using pressure transmitter methods. Meanwhile, the results show that the gas hold-ups in the centre region increase constantly with an increase in the superficial gas velocity, whereas solid hold-ups distribution is very heterogeneous for high gas velocity. Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the 'inside' flow behaviour of gas –liquid–solid three phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is perhaps the most significant technological innovation in flotation machinery and its successful introduction in mineral processing plants. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker & Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena, Biswal, Das, & Reddy, 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on performance of column flotation (Finch, J.A.;Dobby, 1991). Many techniques have been developed that could be used to experimentally analyse the hydrodynamics of column flotation. Tomography techniques are well sound to investigate the hydrodynamics for process equipment. Among that, Electrical resistance tomography (ERT) has been used in various industrial investigations for visualization of the concentration profiles and characteristics of the fluid dynamics in gas–liquid two-phase systems (Wang, Dickin, & Mann, 1999; Williams, R.A; Wang, 2000). ERT is an imaging technique to analyse the internal flow behavior non-intrusively. ERT provide very useful tools for measuring and monitoring of column flotation process on line. Due to its high speed capability, low cost measurement, robust sensors, ERT is considered to be the most powerful tool among other tomography techniques such as positron emission tomography (PET), magnetic resonance imaging (MRI), optical and infrared tomography. Application of ERT has extended in process systems due to its improved speed of data acquisition, sensitivity, flexibility and noise immunity. In multiphase flow of bubble columns, gas hold-up and solid hold-up are explored by using the coupling of ERT and difference pressure method (Jin, Han, Yang, & He, 2010)."

Jan 1, 2016

By S. Kelebek, E. Yalcin

"Diethylenetriamine (DETA) and/or triethylenetetramine (TETA) are reagents that can generally be categorized under ""flotation modifiers"". These polyamines are known to be effective for the deactivation/depression of pyrrhotite that is present in Canadian nickel-copper sulphide ores in large quantities. Recent bench scale testing on some of these complex ores indicated that chalcopyrite flotation can also be adversely affected under certain conditions involving polyamines, which may be taken to be an evidence of their specific affinity towards chalcopyrite. In general, DETA shows no significant depressant action on chalcopyrite while TETA's promotion of hydrophilicity for this mineral has been observed even in the presence of xanthate. This prompted an investigation on thermodynamic equilibria involving these polyamines and copper ions. Results serve a useful purpose to identify conditions for deactivation phenomena. CuDETA2+ and CuTETA2+ chelates as products of sequestration have large predominance areas covering a wide range of redox and pH conditions, where copper xanthate species are not stable, especially in the presence of TETA."

Jan 1, 2009

By W. D. Madeley

Synthetic minerals were made from pure starting materials and galena samples were doped with the title metals. Microscopic, microprobe and X-ray examination confirmed that the dopeants were in solid solution. Paired flotations in a Hallimond-tube apparatus were performed to determine relative flotation response using Aerofloat 238 promoter. Results of these tests show that silver-doped galena floats more readily than pure galena and that galena doped with bismuth floats less readily than pure mineral to a 95% confidence level. Galena doped with both silver and antimony as AgSbS2 shows no detectable effect. Antimony-doped galena followed the expected trend, but not to 95% confidence. The results are consistent with the theory that flotation by thiol-type anionic collectors is enhanced by p-type semiconduction.

Jan 1, 1978

By Claude Bazin

The Quebec province in Canada is a major producer of aluminium through electrolysis of alumina. The alumina that feeds the electrolysis cells is mainly imported from foreign countries, where it is extracted from bauxite. Other alumina sources, such as clays, have sometimes been considered as potential substitutes for bauxite. There is a large clay deposit in the area of Murdochville in Quebec, with sulfuric acid and electricity available nearby the orebody, as well as sea port facilities leading to the major aluminium plants in Quebec. These are favorable factors to assess the economics of an industrial plant to produce alumina from clays. This paper reviews some of the processes considered for the extraction of alumina from clays and presents results of the initial work carried out on the clay available from Murdochville.

May 1, 2001

By I. H. Warren, F. A. Forward, A. Vizsolyi

"Observations are reported on the pressure leaching of material produced by subjecting chalcopyrite to two types of heat treatment. Calcination of the mineral at 825°C, in the absence of oxygen, induces some sulphur loss by volatization, producing a material from which copper can be leached more rapidly than from chalcopyrite. Treatment of the mineral with elemental sulphur at 475°C leads to sulphur uptake accompanied by a change in mineralogical structure of the chalcopyrite. Copper is prefer-entially and rapidly leached from the sulphur-treated material. A tentative explanation of the sulphur-chalcopyrite re-action is presented."

Jan 1, 1968

By Piotr Malkowski

Studies on the properties of rocks heated to high temperatures are rather rare. Such research is occasionally conducted for example; in areas around nuclear power plants. The national Polish coal gasification (underground coal gasification, or UCG) project has, however, forced the analysis of the geomechanical properties of heated rocks in the vicinity of a designed geo-reactor. Ukrainian experience with UCG show that rocks up to 2 m from the burned coal seam be at a temperature > 600ºC. Such a high temperature will undoubtedly influence their physical properties. This paper presents studies on the strength and deformation properties of carboniferous rocks in the Upper Silesian region, where the UCG process is planned. Three types of rocks were tested: claystones, mudstones and sandstones. Laboratory tests of these rocks evaluated compressive strength, elastic modulus and weight loss. An evaluation of the results of the tests comparing the thermal conductivity of rocks and their specific thermal capacity was then carried out. All of the rocks studied were heated to 300, 600 and 1000ºC, and also evaluated at room temperature. This procedure shed new light upon the behavior of heated rocks in relation to their distance from the designed geo-reactor. The test results presented were developed within Research Task No. 3 ?Developing a technology of coal gasification for efficient production of fuels and electric power?, financed by The National Centre for Research and Development under strategic research and development programme ?Advanced Technologies for Energy Generation.?

Aug 1, 2013

By S. M. C. Santos

Preliminary bench-scale studies were carried out on the leaching of a zinc sulphide concentrate from Somincor, Portugal, and the purification of the resulting pregnant solution using solvent extraction techniques. The sulphide concentrate contained 36% Zn, 36% S, 2% Fe and 4% Cu. The leaching was carried out with sulphuric acid in the presence of ferric sulphate as the oxidant. Important leaching parameters, such as the effect of reaction time, the solid-liquid ratio, temperature and concentrations of acid and oxidant, were investigated. After leaching, the recovered solution was contacted with an organic phase containing Acorga 5640 to remove the copper. Subsequently, the removal of iron from the leaching solution was achieved with a mixture of Cyanex 272 and TBP. This solvent mixture was relatively selective for iron over zinc. The stripping of the loaded solvent was performed with 200 g/L H2SO4. Six countercurrent extraction stages achieved a separation of about 99% of the iron from the leaching solution. The iron-free leachate can be further treated to recover minor metals by cementation, and finally, zinc by liquid-liquid extraction. The advantages of the suggested process relative to the traditional jarosite process are discussed.

Jan 1, 2006

By A. I. Gorshkov, Y. A. Bogdanov, O. Y. Bogdanova

Abstract - Detailed crystal-chemical study of iron and manganese oxides and some other minerals from low-temperature hydrothermal deposits in a newly discovered inactive mound in the TAG hydrothermal field were used to determine the precipitation sequence of mineral phases during lowtemperature processes and their post-sedimentary transformations. Particles of primary sedimentary X-ray amorphous proto-ferrihydrite with high silica content were replaced in situ by nontronite, ferrihydrite, or goethite during alteration. Ferrihydrite is the only proto-hematite phase. The transformation of the iron minerals, related to change in the physicochemical environment, is an important characteristic of low-temperature hydrothermal processes. The occurrence of hydrogenetic Fe vernadite and Mn feroxyhyte in the uppermost part of low-temperature deposits and bottom sediments near the base of the mound is evidence for cessation of low-temperature hydrothermal processes. Among the investigated mineral phases, goethite, nontronite, and hematite are stable in reduced sediments only.

Jan 1, 1999

By T. Patching

"Introduction The occurrence of coal was first reported in the Drumheller area in 1793 but it was not until 1912 that production of coal was recorded. In that year 13,000 tonnes were mined in the Drumheller area. Three years later the Drumheller mines ranked next in the Province to those in the Crowsnest and Lethbridge districts, with an output of 225,000 tonnes. By 1917 production had increased to 600,000 tonnes, moving Drumheller to second place in output in the province, second only to the Crowsnest district. It held this rank until 1960. Production, almost all from underground mining, rose to over a million tonnes a year by 1920 and remained between one and two million tonnes per year until 1954. Competition from newly discovered oil and natural gas, beginning around 1950 caused a steady loss of domestic coal markets, especially from underground mines. By 1960 Drumheller's production had fallen below a half a million tonnes per year and the field ranked third in output in the province, being surpassed by new stripping operations in the Castor field. By 1965 only a couple of producing mines remained in the Drumheller valley, and output was only about a quarter of a million tonnes per year(1). Throughout the life of the field production was seasonal, depending mainly on the domestic heating market. In 1979 the last mine ceased production. For the last several years of its operation it had remained open in the summers to provide tours for visitors(2). The Drumheller mining operations were located along or near the Red Deer River valley which is 300 to 400 feet deep, and extended from a few miles above the city of Drumheller to East Coulee, about 13 miles down the river in a south-easterly direction. Intervening mining communities existed for some years at Wayne and Rosedale. During the peak years of production some 2000 to 2500 miners and their families lived in these communities and the surrounding areas."

Jan 1, 1985

By McGill Metals Processing Centre, S. Chang, L. Calzado, X. K. Cao, C. H. Hsin, M. Isac

"Due to the increasingly stringent cleanliness requirements for final steel products, there has been a growing interest in the possible use of micro-bubbles for the removal of inclusions with diameters smaller than ~50µm, present within the steel passing through a steelmaking tundish. However, several technological barriers have prevented the adoption of this technique in industry. These are related to a) the generation of micro-bubbles in liquid steel, b) the measurement of bubble size distributions, and c) the optimization of bubble injection conditions to create micro-bubbles. In the present study, a novel Aqueous Particle Sensor (APS) system was developed for the in-situ, on-line, detection of micro-bubbles in water, generated by a newly designed full-scale ladle shroud, located at McGill Metal Processing Centre (MMPC). Measurement results from the sensor were validated against bubble size data collected through a high speed camera and post-processed through the commercial software, Image J.Control variables and orthogonal experiments were designed to assess the dependence of average micro-bubble sizes and bubble size distributions on key experimental parameters. Those chosen were the air inlet flowrate, the distance of the gas injection port from the slide gate, and the number of injection ports used. The investigation demonstrated that the APS system can be successfully adapted to detect micro-bubbles up to ~800 micron diameters. Using this novel sensor, it was shown that multi-port injection using low air inlet flowrates, closer to the slide gate, were useful in forming small micro-bubbles within the flow through the ladle shroud. The results from the APS system were compared and validated against data resulting from an optical technique. INTRODUCTIONModern industry expects increasingly stringent cleanliness requirements for final cast products. Therefore, the numbers and sizes of inclusions need to be strictly controlled in steelmaking operations. Thus, the cleanliness of steel products depends on the amount, morphology and size distributions of nonmetallic inclusions in steel (Zhang L. & Thomas B., 2003). Since large, deep, tundishes provide longer nominal residence times for liquid steel passing through it to the exit SEN’s, this can provide the ideal place to separate inclusions, and bubbles can assist by removing help attach inclusions and float them to the top surface."

Jan 1, 2016

By J. W. Choung, T. Fu, Z. A. Zhou

An on-line visualization technique and methodology was developed to investigate the role of fine sphalerite (< 10 um) aggregation in flotation. The images of particle aggregates under different operating conditions were recorded and analyzed. The effect of impeller design on particle aggregation was demonstrated. This difference was not mainly due to the energy input into the system, but due to the resultant hydrodynamic conditions created by the impeller and their effect on particle interactions. The recorded image showed that adding fine silica (- 5 um) did not interfere with fine sphalerite aggregation, thereby showing no effect on the sphalerite recovery. Effect of the enlarged aggregate size on increasing flotation recovery was confirmed. Although Malvern Mastersizer produced consistently lower estimates of aggregate size than those by the image analysis, both methods responded to the changes in operating conditions in the similar trend. It was shown from this study that on-line visualization technique is a powerful tool for studying fine particle aggregation and morphology in the context of diagnosis for the flotation separation.

Jan 1, 2004

By T H. Clark, R P. Doig, V. A. Saull, R B. Butler

Terrestrial heat flow has been determined for four boreholes in the Montreal area. The mean value of the results (uncorrected for glacial effects) is 0.790 ± 0.053 x 10-6 cal/ cm2/sec (95 per cent confidence limits). Thermal gradients were determined using a thermistor probe and d-c bridge, and also by a new method using a probe-contained phase-shift oscillator, the output frequency of the oscillator being a function of probe temperature. Thermal conductivity determinations were made on core from the boreholes, using a divided bar apparatus. INTRODUCTION T HIS paper concerns the terrestrial heat flow in the St. Lawrence lowland of Quebec, as determined from measurements on four of the numerous boreholes drilled in this region for gas and oil. The work has been supported by Geological Survey of Canada Re-search Grant 3-58, awarded to T. H. Clark and V. A. Saull. This sup-port is hereby gratefully acknowledged.

Jan 1, 1962

By M. Mbonimpa

Field experimental cells were constructed in 2007 to assess the performance of different cover scenarios for the reclamation of the Parc 1 tailings disposal facility at the Westwood-Doyon Mine site (Abitibi, Quebec). Three configurations of cover with capillary barrier effects (CCBEs) with different thicknesses and material types for the moisture retention layer (MRL) were studied. MRL with 80 cm till, 40 cm till, and 40 cm clayey silt were used for cell nos. 2, 3, and 5, respectively. The capillary barrier layer (CBL) and drainage and protection layer (DPL) of the CCBE consisted of 30 cm gravel. A reference cell without cover was also constructed to compare the geochemical performance of the CCBEs. Due to an unexpected flooding in the leachate exit area of the cells in spring 2008, the cell instrumentation for hydrogeotechnical monitoring was postponed to spring 2009. Changes with time in volumetric water content, suction, soil oxygen concentration, and temperature were measured at different depths. This paper presents and discusses preliminary results obtained from spring 2009 to autumn 2010. In all cases, the degree of saturation Sr is lower in the CBL than in the MRL, indicating the presence of capillary barrier effects at the interface of these layers. Cell nos. 2 and 5 showed hydrogeotechnical behavior typical of an effective CCBE, with Sr maintained above 85% in the MRL and lower than 30?50% in the DPL and CBL. Based on the obtained results, and as expected, MRL thickness and the type of construction material used appear to affect the hydrogeotechnical behavior of the CCBE. Oxygen concentration profiles through the CCBEs were used to estimate the oxygen flux, and results indicate that cell nos. 2 and 3 performed better than cell no. 3. CCBE performance is currently being investigated using the geochemical monitoring data.

Aug 1, 2013

By G. A. Kosick, M. Freberg, L. A. Kuehn

"Highly variable and higher than forecast lead miff feed grades were problems experienced at the Polaris Concentrator. Limited flotation capacity and poor operating flexibility prevented the plant operators from overcoming these difficulties, and resulted in grades and recoveries which were lower than necessary.Two column cells were integrated into the lead circuit in an effort to give the operators the tools they required to achieve the best grades and recoveries possible, regardless of the miff feed grade. Installation of the column cells increased lead concentrate grade from 76% to 79.3% Pb, and increased lead recovery from 9/% to 91.3% Pb.This paper reviews the design, development and operation of column flotation cells in the lead circuit at the Polaris Mine.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec, and towed to its pre sent location on Little Cornwallis Island, Northwest Territories, about 1450 km from the North Pole. The plant presently treat s about 2800 mtpd of new feed with average feed grades of 3010 Pb, 13% Zn and 5% Fe. Current production averages 36 000 tonnes of lead concentrate and 220 000 tonnes of zinc concentrate annually.The barge design and min e location dictated that the concentrator .be compact with very little unused floor space. As a result, flexibility was limited in terms of expanding the plant.Mill feed grades were highly variable and above forecast and the lead flotation circuit was found to be under capacity. This caused continued overloads in the lead cleaning circuit, resulting in low concentrate grades and recoveries. It was evident that an increase in lead flotation capacity and flexibility was necessary. The existing floor space did not allow for the installation of additional conventional flotation cells, but one alternative was the installation of column cells."

Jan 1, 1988

By G. Morin, F. Chiesa, B. Tougas, B. Duchesne, Jocelyn Baril, N. Giguère

"An aluminum A356 compressor impeller was sand cast using the Low Pressure technique. The casting was limited in size (170 mm in diameter, 1.2 kg in weight) and very intricate in shape thus making 3D mold printing particularly favorable; indeed, producing this part by the traditional pattern-core box route would involve mounting 12 cores inside the mold while stringent dimensional tolerances are required as the impeller blades are only 2 mm thick. Consequently the molds were produce on the X-One MFlex printer of Quebec Metallurgy Center - CMQ. A dozen castings were produced with different casting temperatures and filling times so that it was possible to assess under which conditions complete filling of the mold cavity would be achieved. Filling and solidification modeling allowed predicting misruns and metallurgical properties inside the A356 (AlSi7Mg04) casting.INTRODUCTION Recent advancements in additive manufacturing enable foundries to produce molds without the tooling (pattern and core boxes) necessary when conventional technology is used (Eyad, 2016). This is particularly advantageous when dealing with intricate shapes and/or when a limited number of parts must be produced within a few days rather than in 5 weeks. An additional advantage is gained when producing prototypes (Johnson, 2016) as changes are much less costly and time consuming when made on a numerical 3D drawing rather than on patterns and core boxes. 3D printing is normally economical for a small number of parts; however, if the part is not too big and very intricate in shape such as the part that will be studied in the present work, 3D printing can be economical even for an important number of castings to be produced. On the other hand, low pressure casting is a high integrity casting process in which the mold cavity is filled from the bottom via a transfer tube in which the liquid aluminum rises under the pressure applied at the surface of the melt as illustrated in Figure 1. The filling can thus be precisely controlled, eliminating the turbulence created when the mold is filled from the top (gravity casting). Also, the pressure applied on the melt during solidification results in excellent feeding of the casting when conditions of directional solidification are met. In the present work, the compressor impeller shown in Figure 2 will be sand cast by low pressure."

Jan 1, 2018

By R. T. McAndrew

Introduction Drinnan is situated in the Prairie Creek coal area in the Foothills belt of Alberta. It lies on the main line of the Canadian National railway from Edmonton to Jasper. The exact location is shown on the map (Figure I). Interest in the field was aroused by several circumstances: Its proximity to Brule and Pocahontas on the southwest and to Coal-spur on the southeast led to the belief that coal might be economically produced here. There was already at Hinton a 3 ft. 9 in. coal seam being mined by Seabolt. The coal was of very good grade, being black and shiny in appearance with well defined cleavage and a heat value of 12,000 B. t.u. Outcrops of coal had also been noticed on the north side of the Athabaska river and Fish creek. These facts led the Jasper Coal Company to investigate the field. This Company considered taking over the Seabolt property at Hinton, but, owing to the size of the seam, this plan was abandoned and prospecting by diamond drills and test pits was started two years ago in the district east of Hinton. After prospecting had been completed, the most favourable district was found to be in township 51, ranges 24 and 25, west of the 5th meridian. The Company&apos;s lease includes all or parts of sections 18, 19, 20, and 28 in range 24, and sections 10, 11, 12, 13, and 14 in range 25. The approximate boundaries of the property are the Canadian National railway on the north, Happy creek on the west, and Cache Percotte creek on the east. The lease comprises 3,100 acres, and the total amount of coal in sight is estimated at 100,000,000 tons.

Jan 1, 1931

By R. V. Kumar, C. Schwandt, S. Subramanian, S. Sampath, S. Vimalnath

Waste waters and industrial effluents containing toxic heavy metals such as Pb, Hg, As and Cr, beyond permissible limits (0.1 ppm, 0.01 ppm, 0.02 ppm and 0.05 ppm, respectively) (WHO, 2011), pose serious threats to the ecosystem, when discharged into the environment. It thus becomes imperative to monitor the concentration of the toxic heavy metals and treat them before discharging. In this study with the above objective in mind, a microbial sensor has been developed using P. aeruginosa cells drop coated onto a carbon paste electrode (CPE) for the detection of Pb(II) ions in aqueous solutions. Detailed biosorption experiments confirmed that complete bioremoval of lead could be achieved using P. aeruginosa cells under optimum conditions of pH and biomass loading. For the electro-analytical determination, the Pb(II) ions were initially preconcentrated on the P. aeruginosa modified CPE, reduced and then anodically detected with oxidation of Pb0 using differential pulse anodic stripping voltammetry (DPASV) technique. All the experiments were carried out in the presence of 0.1 M sodium acetate buffer and KNO3 as background electrolyte. The parameters namely pH, scan rate, biomass loading, deposition potential, deposition time and concentration of Pb(II) ions were optimized for the biomass modified CPE, to obtain maximum voltammetric response. Under the optimized conditions of pH 5.6, scan rate of 0.008 V/s, biomass content of 1.7–1.8×109 cells/mL, deposition potential of –1.2 V, and deposition time of 500 s, the developed microbial sensor showed a linear response for the peak current between 0.5×10-5 M and 1×10-8 M of Pb(II) ions with the R2 value of 0.9979. The lowest limit of detection (LLOD) was determined as 2.4×10-7M of Pb(II) ions (0.05 ppm). The redox mechanisms of Pb(II) ions on the P. aeruginosa modified CPE surface are discussed.

Jan 1, 2016

By L. G. Bergh

The experience developing a supervisory control and information systems in a SX pilot plant is presented. The plant is located at the Process Control Laboratory, Santa Maria University, in Chile. In this work, the problem of controlling this process is discussed and related literature is briefly reviewed. Then, an innovative control scheme organized in three levels, local, hydrodynamic, and metallurgical supervisory controls is presented in an architecture including field controllers, PLC, and PC networks. Operating decisions in the metallurgical supervisory control are taken with incomplete information from on-stream analyzers. The control proposed is based on metal and acid concentration predictions of intermediate and exiting streams through the use of dynamic and static models and flow rates and input concentration measurements. Preliminary results are presented. The main objectives are to develop and test intelligent techniques in a hybrid system, and to study measurement and supervisory control problems. It is expected to produce reliable results that will contribute to improve the efficiency of this emerging and important process.

Jan 1, 2007

By J. C. Keenan

Company-community agreements are widely considered to be a practical mechanism for recognising the rights, needs and priorities of peoples impacted by mining, for managing impacts and ensuring that miningderived benefits are shared. The use and application of company?community agreements is increasing globally. Notwithstanding the utility of agreements, the gender dimensions of agreement processes in mining have rarely been studied. Prior research on women and mining, however, does show that women are often more adversely impacted by mining than men, and face greater challenges in accessing development opportunities that mining can bring, however there is currently little to no guidance for companies, government or communities in terms of bringing a gender perspective to the fore in mining and agreement processes. While it is undisputed in human development literature that investment in women and sensitivity to gender delivers long-term health, education and local development outcomes, a number of key factors remain unexplored in debates about mining and development. These include: women?s participation in agreement processes, the gendered distribution of agreement benefits, and the extent to which impacts and benefits influence (either positively or negatively) women?s development and economic inclusion. This paper presents the results of an applied research project undertaken by the Centre for Social Responsibility in Mining (CSRM) at The University of Queensland and funded by a partnership between the Minerals Council of Australia (MCA) and the Australian Agency for International Development (AusAID). The project sought to connect with practitioners who had been directly involved in agreement processes to hear grounded perspectives on the interaction of gender dynamics and agreements, and connect those experiences with the broader literature. Findings from this study have implications for the role of companies and governments in promoting gender equality and empowerment as part of their commitments to sustainable development. A key challenge for companies will be navigating the territory of cultural norms and gender equality. The authors argue that without consideration of the gender perspective, and appropriate responses, mining agreements may not be inclusive or representative and may exacerbate gender inequalities and fail to contribute to long-term sustainable development.

Aug 1, 2013

By A. H. Duffield

"Forming part of the Prairie Evaporites, the sylvinite layer mined at Alwinsal underlies the Blairmore quicksands and the water-bearing Devonian formations. Production is achieved by a method of trackless, continuous mining of rooms, leaving pillars for natural support. The paper describes the development of the mine, and the equipment and organization employed in the operation and maintenance of the underground facilities."

Jan 1, 1972