Search Documents

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

By R. Tomás, J. B. Serón, M. Romana

The Slope Mass Rating (SMR; Romana, 1985) geomechanics classification was developed as a sequel of Bieniawski’s Rock Mass Rating (RMR) system, which was almost impossible to use in slopes due to the extreme range of the correction factors (up to 60 points of a maximum of 100) and to the lack of definition of them. A detailed quantitative definition of the correction factors is one of the advantages of SMR classification. During the last thirty years the use of SMR system has been extended to many countries from the five continents and, thus, it is time to review the most interesting developments. Both RMR and SMR are discrete classifications, depending on the values adopted by the variables that control the parameters. This can cause major changes in the parameters value due to small differences in the variables value, with changes in the final rock mass assigned quality. On the other hand, geomechanics quality indexes are extremely biased. To avoid this problem, some authors have proposed continuous functions for SMR. This classification has been also adapted for its application in heterogeneous and anisotropic rock masses, for high slopes, for is application trough stereographic projection and Geographical Information Systems, has been used as susceptibility rockfall parameters and has been included in the technical regulations of several countries. Additionally, some open access computer tools have been developed for the computation of SMR. Consequently, this paper reviews: 1) the most important modifications and adaptations of slope classifications which derive directly from SMR; 2) the use of SMR throughout the world; 3) many significant papers on slopes analysed with SMR all over the world; and 4) future trends in the use of SMR.

Jan 1, 2015

By J M. Fletcher

The responsibility and scope of the Industrial Engineering Department, as organized at the Jeffrey mine, has been broadened to include any study, project or report that could result in more effective use of men, materials and equipment. Although still emphasizing wage incentives and co t reduction, much more varied work is now done, consistent with the in-.creased complexity of industry. Additional activities now include production, maintenance and inventory control improved job evaluation, packaging, labour utilization studies, technical sales liaison, mining, milling and service department n1ethods, plant layout, and specialized project analysis. Additional techniques include the extensive use of work .sampling and standard data. A recent trend has been toward increased emphasis on industrial relations, both in introducing change to the men and in providing requested explanations to Union stewards and officers. These new responsibilities have resulted in the development of specialists in some rather narrow industrial engineering fields, as well as the necessity for industrial engineering assistance in supervisory and job training.

Jan 1, 1963

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By D. Emadi

The ASTM B108 Mould and a Modified Mould were used to cast test bars under a variety of conditions: mould and pouring temperatures, mould coating and tilt. Mechanical properties were determined in the as-cast and heat-treated conditions. The ASTM Mould is less sensitive to casting variables. Enlarging the gating system and adding additional gates to the ASTM mould can improve properties in the tilt position. The reproducibility of properties in as-cast and T6 heat treated bars was investigated.

Jan 1, 2004

By M. R. Khalesi, S. Bellec, C. Bazin, D. Hodouin

This paper proposes a classification model to predict the split coefficient of gold ore particles as a function of the particle size and gold content. The model is calibrated and validated using data obtained from the sampling of an industrial grinding circuit. Model calibration is based on a complete simulation of the circuit and involves parameters related to the gold grain distribution in the ore as well as a grinding and liberation model. Since cyanide is added into the studied grinding circuit, assumptions related to gold dissolution in the mills are made to allow simulation results which reflect industrial behaviour patterns.

Jan 1, 2011

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By H. -L. Heikkilä, E. Peuraniemi

"Boliden Harjavalta Oy has a long tradition in the Finnish metal industry starting from the 1930's. The Smelter consists of copper and nickel flash smelting lines. Off-gases are captured in the acid plant to produce sulfur products. During the early years of production, the surrounding environment suffered from high SO2 and dust emissions. The first acid plant started in 1947, a few years after commissioning of the smelter. The flash smelting method was developed and commissioned in 1949. This created the basis for today’s environmentally sound metal production. Recent air emission reductions are related to treating lean ventilation and granulation gases. Emissions from the stacks are monitored with continuous measurement devices. SO2 and PM10 concentrations are also measured from the residential area and reported online in cooperation with Harjavalta community and other local industry.INTRODUCTIONProductionBoliden Harjavalta Oy smelts copper and nickel concentrates and refines copper in the western part of Finland. The copper concentrates come from external copper mines mainly in South America and Europe. Concentrates are unloaded at the Pori harbor and transported to Harjavalta by train from a distance of about 60 km. Boliden Harjavalta Oy has operations in Harjavalta and Pori. The smelter in Harjavalta produces copper anodes that are transported via railway to the copper refinery in Pori. The anodes are electro-refined into copper cathodes and by-products like Se, Ag, Au and Pt/Pd concentrate. In the Harjavalta smelter SO2 containing gases are delivered to a sulphuric acid plant where sulphuric acid and liquid sulphur dioxide are produced.Our nickel smelter smelts nickel concentrates on a tolling basis to produce nickel matte for customer needs. SO2 containing off-gases are delivered to the sulphuric acid plant for sulphur capture and modification into products.All our operations are certified according to the Quality, Environmental and Occupational Health and Safety Standards ISO 9001, ISO 14001 and OHSAS 18001. Boliden Harjavalta Oy was the first company in Finland operating in the metal and technology industry to be certified according to the Energy Management Standard EN 16001, currently this certification is done according to ISO 50001."

Jan 1, 2012

By G. J. Birnie

Introduction The preparation of the following paper has been undertaken in the belief that a description of the development methods and equipment used at Lake Shore, at the present time, will prove of general ? interest. Working depths of nearly a mile and a half in shaft sinking and of more than one mile for stoping operations have imposed problems not encountered at shallower horizons. Among the problems contributing to the difficulty of mining at extreme depths might be mentioned: Rock pressures Ventilation Hoisting Shorter work period at the face Geological considerations In the main, the effects of these factors add to the difficulty of mining at depth, but it is not entirely true to say that each must necessarily become more pronounced as mining operations proceed to greater depths. Corrective measures may, in some cases, retard the effect and in others may even relieve some of the difficulty. It is proposed here to discuss these features in the light of the experience at Lake Shore, and to present, in some detail, the current practice in shaft sinking and in driving ore and waste passes, raises, drifts and cross-cuts.

Jan 1, 1950

By P. Langlois, G. Labonté, J. J. Barrett, J. Holmes

"The Voisey’s Bay mill processes a high-grade pentlandite and chalcopyrite ore in a largely pyrrhotite/troilite matrix. From 1994 to 1997, circuit development focused on making a 14% nickel concentrate. When flowsheet development resumed in 2001, the target grade was raised to 20% ni. initially triethylene tetramine and sulfite pyrrhotite depressants were used in a lime circuit, but by recycling process water and the contained thiosalts, the required nickel grade was made without depressants. construction of the mill was fast-tracked, with start-up in september 2005. ramp-up was faster than other recent nickel installations, with tonnage being limited by concentrate dewatering due to higher-thanexpected ore grades.RÉSUMÉ l’usine de traitement de Voisey’s Bay traite un minerai à teneur élevée en pentlandite et chalcopyrite dans une matrice formée surtout de pyrrhotite/troïlite. De 1994 à 1997, le développement du circuit ciblait la production d’un concentré à 14 % de nickel. lorsque le développement du schéma de traitement a été repris en 2001, la teneur cible a été élevée à 20 % de ni. initialement les déprimants triéthylènetétramine et sulfite de la pyrrhotite étaient utilisés dans un circuit à la chaux; cependant, en recyclant l’eau du procédé et les sulfosels qui y sont contenus, la teneur en nickel a été atteinte sans utilisation de déprimants. la construction de l’usine de traitement a été accélérée et elle a démarré en septembre 2005. la mise en opération a été plus rapide que pour d’autres installations récentes de nickel; le tonnage traité étant limité par le séchage du concentré en raison des teneurs de minerai plus élevées que prévu.INTRODUCTIONnickel was discovered on canada’s east coast in the vicinity of Voisey’s Bay, northern labrador, by chislett and Verbiski (Higgins, 2011) while working for Diamond Fields resources in 1993. The ovoid deposit was subsequently delineated in the winter of 1994–1995. By the end of 1995, the ovoid had been well explored, and at that time was thought to have a reserve of at least 30 million tonnes (Mt), with an average grade of 2.83% ni and 2.0% cu (naldrett, singh, Krstic, & li, 2000). Drilling to the east of the ovoid indicated the presence of significant mineralization. in June 1995, inco limited bought a 25% share in the Voisey’s Bay nickel company (VBnc), which was a subsidiary holding company set up by Diamond Fields. inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBnc for 20 years as part of this agreement. in april 1996, inco bought Diamond Fields and acquired the remaining 75% of VBnc shares."

Jan 1, 2017

By G. E. Veins

A three-phase, continuously-operated, 250 kv.a. electric smelting furnace has been installed at the Mines Branch, Department of Mines and Technical Surveys, Ottawa, for the experimental treatment of ores and by-products of interest to the Canadian mining, metallurgical, and chemical industries. In the operation of this furnace particular emphasis is placed on the accumulation of quantitative data which will be useful in determining the most suitable smelting technique and the nature of the products, and in arriving at preliminary conclusions regarding the cast of power and electrodes. The results obtained in the experimental smelting of iron, manganese-iron, titanium- iron, nickel, and chromiumiron ores, and of a number of industrial by-products, clearly show the value of such treatment for materials of this type.

Jan 1, 1957

By Guy Archambault, Réal Daigneault

"Un trait marquant du cadre tectorwstratigraphique de la Sous-province de l'Abitibi est la présence de nombreux couloirs de déformation d’extension régionale et sub-concordants au grain stratigraphique. La présence de grandes masses granitoïdes qui perturbent l'allure du grain tectonique est typique de la partie nord de la Sous-province de l'Abitibi. Des rides E-W constituées de complexes plutoniques précoces forment des reliefs structuraux agissant comme des moles résistants qui interfèrent avec la déformation régionale.Deux types de couloirs de déformation sont distingués, les couloirs de bordure et les discontinuités structurales. Les couloirs de bordure représentent des auréoles de déformation élevée qui s’accompagnent généralement d’un métamorphisme au faciès amphibolite. lls suivent /'interface entre les roches granitoïdes et les assemblages supracrustaux. Ces couloirs sont de puissance kilométrique et sont confines, surtout au sein des roches vertes, a l’interface des complexes granitoïdes d’importance. La limite entre la Sous-province de l'Opatica et les roches supra crustales de l'Abitibi est caractérisée par un important couloir de bordure issu possiblement d'un chargement tectonique irrégulier et concentre lors du raccourcissement horizontal.Les discontinuités structurales sont des failles ductiles qui se propagent surtout en direction E-W mais avec des variantes de directions SE et NE. Les discontinuités E-W se caractérisent par la présence d'une linéation d'étirement à fort angle de chute. Les discontinuités SE sont caractérisées par des linéations d'étirement horizontales et directionnelles et les mouvements observes sont system attiquement dextres. Les discontinuités NE sont des failles à comportement beaucoup plus fragile et se distinguent par des composantes de mouvement senestre. Elles sont tar dives par rapport aux discontinuités E-W et SE et ne représentent pas la symétrique du système SE.La combinaison des systèmes E-W et SE décrit un motif anastomose a l' échelle régionale. Les failles ductiles se rejoignent defaçon asymptotique, isolant des blocs peu ou pas affectes par la déformation. L'anastomose est un phénomène qui se produit a toute échelle et est reliée principalement aux Mt érogénéités et aux anisotropies 1) des forces agissantes (champs de contraintes régionale et locale) et 2) de la réponse del' empilement supra crustal (compositions différentes, fabrique initiate, propriétés mécaniques variées, niveaux d'altération).Dans le but de respecter un raccourcissement horizontal N-S, différents modelés sont proposés; ils mettent en cause soit une transpression dextre, soit des failles inverses réactivées en failles décrochèrent dextres soit des failles de chevauchement redressées."

Jan 1, 1990

By Tapio Leskinen, Jouko Koskinen, Timo Nlltti, Lappalainen Seppo, Pentti Vanninen

"The Courier 300 on-stream analysis system manufactured by Outokumpu has now been in operation at five of the company's concentration plants long enough to give a reliable basis for closer examination of the benefits achieved in control of these processes. The first system was installed at the Pyhiisalmi mine at the end of 1967. Since November 1970, two analyzers have been in operation at Pyhiisalmi feeding the assay data to a process computer which controls the whole plant and does the optimization of the process. In October 1970 the Courier 300 analysis system was installed at S. T. O. LESKINEN J. KOSKINEN the Keretti concentrator of the Outokumpu mine, followed soon by installations at the Vihanti Mine in May 1971, at the new Vuonos mine in November J 971 and at t he Kotalahti mine in December 1971. Since installation of the Courier analysis systems, considerable improvements have been achieved in the control and the economy of the plants. Immediate knowledge of the changes in the process and the possibility for rapid action has resulted in evener production and higher capacity and recovery. The recovery has been increased most significantly at the Vihanti concentrator, which operates on a complex ore. Consumption of chemicals has been reduced at all concentrators. Due to the fact that process control and partly also bilance analysis are not achieved by conventional methods any more, it has been possible to reduce the personnel of the laboratories drastically. Two of the plants, viz. the Pyhiisalmi and the Vuonos concentrators, are computercontrolled. The Vuonos concentrator started operation in January 1972 under computer control from the very beginning. The Pyhiisalmi concentrator has been computer-controlled since 1970. The Courier 300 analysis system was described in detail at the AIME Centennial Annual Meeting (1971). In this paper, less attention is paid to the analysis system. Only the sampling system of the Courier 300 is described in more detail. In the development of sampling equipment, effective use has been made of the company's wide knowledge of the problems involved and the test field offered by its concentrators. The sampling equipment includes secondary samplers and six basically different types of primary samplers, with which most sampling situations can be managed."

Jan 1, 1973

By P. Hr?enjak

Two groups of methods are usually used in design procedures of underground excavation of dimension stone: the analytical and numerical methods of analysis. In all of these methods the in situ rock mass strength represents the main problem. This is due to massive rocks in dimension stone deposits, consisting of large blocks of rock separated with particular discontinuities, for which the Hoek-Brown empirical criterion, developed for jointed rock masses, cannot be realistically used to estimate rock mass strength, especially for a particular block of rock mass or a particular pillar. On the basis of the regular underground excavation process of dimension stone by separating blocks with the flat jack application, we developed the in situ flexural strength testing method. We carried out numerical analyses and evaluation of uncertainty of measurement in order to validate the in situ flexural strength testing method. On the basis of very good validation results, as well as results of the in situ flexural strength testing of exploitable layers on the ?Kanfanar? quarry, we introduced a new coefficient of reduction, which can be used for correction of other strength parameters determined by laboratory testing for obtaining a realistic value of rock mass strength.

Aug 1, 2013

By J. Wong, M. G. Lipsett, L. K. Daneshmend

"Current trends of increased size, complexity, and automation of surface mining equipment necessitate more comprehensive and objective techniques for equipment comparison and selection. The field of reliability analysis provides tools to generate quantitative bases for maintenance and reliability aspects of such comparisons. Results from statistical analyses of failure and repair time data are used to perform the comparison. A case study is presented which analyzes five machines of two different technologies and three different designs.IntroductionThe surface mining industry is currently faced with a rapid evolution in production equipment. The more obvious trend in this evolution is the steady introduction of even larger machines. Parallel, and complementary, to this increase in size is the introduction or adaptation of new technologies. Together, these two trends result in new surface mining equipment designs; these designs are often more complex and may feature technologies that have yet to be proven for the application or at the scale they are now fielded.The prospect of significant automation of open pit equipment is also bound to add complexity to future equipment designs. Semi-automated features, such as drilling controllers (Aquila, 2000), have already been commercialized. Fully autonomous haul trucks have been demonstrated in open pit mines (Jackson and Zoschke, 2000). Design concepts for comprehensive teleoperation of open pit operations have been formulated (Lipsett, 1998).With this rapid availability and deployment of new technology and equipment, managers and maintainers are faced with a multitude of decisions regarding what equipment to acquire and what maintenance strategies to implement. In light of this evolution in mining equipment, it is necessary to develop better methods for making equipment management decisions (Dessureault et al., 1999; Paraszczak, 1999). The incentive for development of such techniques is that a large portion of an open pit mine’s operating cost is maintenance related, as shown in Table 1."

Jan 1, 2000

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"The future of Polish copper mines KGHM Polish Miedz S.A. will be associated with mining at depth. At present, technologically advanced measures are being introduced to minimize the adverse influence of the environmental hazards on people working underground. Polkowice-Sieroszowice mine is the only mine in Poland where mining takes place in copper and salt deposits. On the basis of the current and anticipated methods of ventilation of a selected ore deposits the paper will analynze a number of solutions enabling planned mining of copper ore deposit, while minimizing the impact of natural aerological hazards in working areas. INTRODUCTION The future of copper ore mining, carried out by KGHM Polska Miedz S.A., will be based on mining from continuously greater depths (Butra, 2015). It is forecast that this will be accompanied by an increasing climatic hazard, resulting from an increase in the original temperature of rocks of more than 45°C as well as gas and geodynamic hazards (Soroko, 2015; Andrusikiewicz, 2015). Due to the safety of underground teams, a need arises to develop methods eliminating the adverse impact of the natural hazards, down to a level enabling the mining activity to be carried out on an industrial scale while maintaining favourable economic parameters. Current depths of the copper ore deposit being developed are effectively verifying the technical methods and measures employed to date for eliminating the natural aerological hazards. Amounts of air supplied to mining areas, with lengthy transport routes, are becoming insufficient for miners’ temperature safety, whereas increasing the power of cooling air-conditioning stations for cooling the air undermines the economic legitimacy. However, along with the temperature hazard, a significant problem at the current depths is an increase in gaseous occurrences in the headings’ areas. The concentrations of natural harmful gases found, even with the values below the permissible concentrations, in the case of limited amounts of air and/or low airflow rates, may pose a considerable danger to the workers. The hazards referred to are currently the major factors determining the advance of headings, above all in mining sections, being the outcome of geological structure and depth of lying of a deposit. However, at the current depths of mining minerals from deposits, room-and-pillar mining systems employed also have a decisive impact on the increase in natural aerological hazards."

Jan 1, 2019

By D. G. Klaren, E. F. de Boer

Self-cleaning fluidized bed heat exchangers have demonstrated unparalleled performance internationally for the implementation of indirect heat transfer in severely fouling fluid environments. The ingenious configuration of recirculated cleaning particles through the tubes of vertical shell and tube heat exchangers provides the ability to solve any problems that arise as a consequence of tube-side fouling during indirect heat transfer to process fluids or slurries. In most cases, the cleaning particles consist of chopped metal wire, however other process-specific materials have been used. In addition to the mitigation of fouling effects, a number of other significant benefits for slurry heating are afforded by the mode of operation of the self-cleaning fluidized bed heat exchangers. Increased turbulence at the slurry/tube interface is imparted by the action of the fluidised particles, resulting in very high heat transfers at relatively low liquid velocities. Furthermore, given the thixotropic nature of most process slurries, the action of the fluidised particles imparts additional shear to the process slurry, resulting in shear thinning effects with a consequent reduction in pressure drop and enhancement of heat transfer across the heat exchanger. The benefits provided by the self-cleaning fluidized bed heat exchanger make it the ideal option for the indirect heating of laterite nickel slurry for High-Pressure-Acid-Leach (HPAL) plants. This article explains the principle and application of the self-cleaning fluidized bed heat exchanger technology for the processing of laterite nickel and cobalt slurries in HPAL plants. It also presents an elegant method to revamp existing direct heated laterite nickel and cobalt processing plants into an indirect heated configuration employing self-cleaning fluidized bed heat exchangers.

Jan 1, 2004

By R. P. van Hille, A. W. van Zyl

The BIOX® culture, aiding liberation of arsenopyrite/pyrite occluded gold, is inhibited by thiocyanate (SCN > 1 mg/L); precluding the recycling of tailings water up-stream of the bioleaching circuit. The activated sludge tailings effluent remediation (ASTERTM) process is a biological process that was developed to facilitate water recovery and treat waste water on-site (to achieve a SCN concentration < 1 mg/L) to be recycled or disposed of. The aim of this study was to investigate the effects of changing temperature and SCN loading on the SCN degradation ability of the mixed microbial population clue to seasonal temperature changes and fluctuations of SCN concentration in the waste water.

Jan 1, 2011

The Mineral Industry of Canada in 1951 Continuance of the remarkable, successive increases in the value -of Canada&apos;s mineral production, chief basis of the nation&apos;s post-war expansion, was one of the highlights of Canadian development in 1951, when, according to the preliminary estimate is-sued by the Dominion Bureau of Statistics and reported in the BULLETIN for February, 1952, mineral output for the year reached a new high of $1,228 millions. This marked an increase of 17.5 percent over the previous year, which was the first in which the billion dollar mark had been reached, and an increase of 143.7 per cent over 1946, when production was valued at approximately $503 millions. While higher prices for the principal base metals accounted for a large part of the 1951 increase, quantity gains were made by copper, nickel, zinc, asbestos. lead, cement, and strikingly important. by petroleum, the value of which exceeded for the first time that of coal production. Gold was an exception to the general trend, being lower in both quantity and value than in 1950. For the first time nickel .came within $9 millions of surpassing-gold as the leading mineral product. Metals and Fuels The value of all metals, estimated at $733 millions, was 18.7 per cent more than in the previous year. Nickel advanced 11 per cent in volume and 34 per cent in value. Copper was up 2.4 per cent in quantity and 21 per cent in value, zinc rose 6.6 per cent in quantity and 35 per cent in value, and although the volume of lead produced was lower by 8 per cent, its value increased by 17 per cent. The tonnage of iron ore was 31 per cent higher than in 1950.

Jan 1, 1952

By F. Guo

"The leaching kinetics of zinc sulphide concentrate was studied under total pressures ranging from 0.3 MPa to 0.5 MPa and leaching temperatures ranging from 358 K to 378 K. The apparent activation energy of leaching reaction under different total pressures was calculated. The results show that for the extraction of zinc at low-temperature pressure leaching is controlled by an interfacial chemical reaction. This was supported mineralogical analysis of the leaching residue. The kinetic equation for low-temperature pressure leaching of zinc sulphide concentrate was further established by quadratic regression on the basis of shrinking core model.INTRODUCTIONThe Roast-Leach-Electrowinning Process (RLE) is the primary route for zinc production and responsible for more than 85% of the total zinc production (Souza et al., 2007). During the roasting of zinc concentrates, fugitive SO2 causes pollution. The prevention of SO2 emissions from the RLE process can be one of the challenges to this technology (Deller, 2005). In the 1980s, the Zinc Pressure Leach (ZPL) process changed the concept of zinc hydrometallurgy, in which zinc sulphide concentrate is directly leached at approximately 423 K and approximately 0.7 MPa oxygen overpressure and the sulphidic sulphur is oxidized into elemental sulphur so that the pollution by SO2 is completely avoided. Since 1981, five zinc plants have adopted the ZPL process either for expansion by integration with existing roasting facilities, or for the production of zinc without any roasting at all (Collins et al. 1994; Barth et al. 1998). The innovation of the ZPL process has made the zinc industries more competitive although it needs an autoclave. The direct leaching technology of zinc is still in development."

Jan 1, 2012