Search Documents

By P Fines, D J. Williams, G W, S Miller

This paper presents the results and findings of geochemical and mineralogical testwork conducted on samples collected from waste rock dumps at two mine sites, located in South Carolina, USA (Site 1) and Sudbury Ontario, Canada (Site 2). Important aspects of the relationship between the physical and geochemical aspects of the dumps are also presented. The overall aims of the project were to 1. determine if the physical and hydrological nature of the waste-rock dumps had any impact on the geochemical and mineralogical characteristics of the dump materials; and 2. to identify key implications for dump construction for ARD control. The results of geochemical and mineralogical tests indicate that the waste rock at Site 1 had undergone significant in-dump weathering and was relatively advanced with respect to ARD evolution. In contrast, the waste rock at Site 2 had undergone some weathering, however still contained a considerable amount of sulfide minerals. Testing also suggested that flushing of oxidation products at Site 2 had been limited, which therefore promoted the storage of oxidation products at the site. In addition, materials that had a D50 particle size in the range of 5 mm to 30 mm appeared to be more readily flushed than samples that had a D50 particle size of 30 mm. This suggested that preferential water pathways may have developed within the dumps at both sites.

Jan 1, 2003

By Yanagase T, Nakamura T, Ueda Y

The possibility of removing the phos phorus and sulphur contained in steelmaking slag has been studied by observing directly through the microscope melts heated on Pt- filaments. After a CaO crystal was placed in the molten slag, distributions of P, S and other elements formed around the CaO crystal were determined with the aid of EPMA. The results indicated that a layer of 2CaO SiO2 is formed on solid CaO in CaO-Si02 melts. Then between CaO and the newly formed compound the molten slag tends to migrate through cracks. For higher Fe 2 03 contents, the layers of the compounds 2CaO.Si02 and 3CaO SiO2 formed around the CaO crystal are not continuous but look more like particles, which promotes the dissolution of CaO. Phosphorus in slag was found to be enriched in the 2CaOòSi02 layer. Phosphorus in the 2CaO SiO2 phase is not related to the primary slag composition, being about 5-7% P205.. Sulphur in slag,as well as the phos- phorus,was concentrated in the 2CaO.Si02 phase. Disintegration due to weathering observed for slags produced in these investigations appeared to be due principally to hydration of lime.

Jan 1, 1980

By B Whiteley, B Gee

The Northside Storage Tunnel is a TBM driven rock tunnel system designed to collect and store sewage from four major storm overflow points along the existing Northern Suburbs Ocean Outfall Sewer. At present, sewage overflows during wet weather are the main source of pollution for Sydney Harbour. The tunnel system comprises a 16 km long by 3.8 m to 6.5 m diameter tunnel from Lane Cove to the North Head Sewage Treatment Plant and a 4 km long by 6.3 m diameter branch tunnel from West Chatswood. The tunnel will have a typical rock cover of about 50 m to 150 m. Most of the tunnel alignment is contained within the Hawkesbury Sandstone Formation which is generally an excellent tunnelling stratum, and offers few geotechnical constraints. However, the tunnel is required to pass beneath incised palaeochannels at Middle Harbour and Manly with each palaeochannel containing about 70 m of sediment.Innovative geotechnical and geophysical investigations were undertaken to examine the tunnel route and characterise the rock beneath the palaeochannels. These investigations have located zones of poor quality rock beneath one palaeochannel in particular, suggesting significant stress relief had taken place in the rock at times of lower sealevel producing structural features indicative of valley bulging. This paper presents the geotechnical model developed for the tunnel, and the models and constraints for tunnelling beneath the palaeochannels.

Jan 1, 1999

By Holcombe R. J, Dobos S. K, Little T. R

Blue amphibole-bearing rocks in the North D'aguilar Block of southeast Queensland occur either as relict pods and lenses within regionally extensive greenschist facies phyllites and schists or as blocks entrained in serpentinite-matrix melange. Epidote + crossite-bearing varieties predominate and formed under conditions consistent with underplating and high P:T metamorphism in a subduction-related tectonic environment. Neither lawsonite nor jadeite has been observed and metamorphic conditions are estimated at 380-4500C for pressures of 0.5-0.8 GPa. High P:T metamorphism occurred during the earliest stages of deformation and was superimposed upon protoliths of inferred Late Devonian - Early Carboniferous age, including mafic volcanics, tuffs and coarse volcaniclastic breccias as well as pelagic and henipelagic sediments, all of which have undergone varying degrees of over-printing to the greenschist facies. Greenschist facies metamorphism occurred during the second phase of deformation and was associated with the formation of mainly flat-lying or subhorizontal structures; it followed the cessation of subduction and occurred in response to either thermal relaxation during uplift or the imposition of regional heating induced by crustal thickening and/or synkinanatic granite emplacement. Uplift and cooling of the high P:T rocks was completed by 260-265 Ma and may have occurred in response to the same extensional processes which gave rise to the onset of rifting in the adjacent Esk Trough.

Jan 1, 1990

By Mann LD

The Haveluck gold deposit, located 2.5km north of Meekatharra, contained 1,284,000 tonnes at an average grade of 1.8 g/t gold of drill delineated proved and probable ore prior to commencement of production. Following successful laboratory and pilot scale testing a decision was made to establish a 300,000 tonnes per year heap leaching operation. The ore, crushed to minus 100mm was stacked on an impermeable membrane and irrigated with a dilute cyanide solution. Gold was recovered from the resulting pregnant solutions by adsorption onto activated carbon and gold bullion produced in a modified Zadra process desorption plant. From the commencement of mining it was obvious that a high percentage of fine material was being produced which would adversely affect the percolation of the cyanide solution-through the leach heaps. A screening plant was incorporated into the crushing circuit which provided an oversize product satisfactory for heap leaching and an undersize for carbon-in-pulp treatment. Plant design provided for the slurrying of minus 0.8mm ore before feeding to the pachuca tanks. Initial practice was to use four tanks for gold dissolution and two for carbon contact. Vibrating screens were used through- out for the carbon-ore separation and the loaded carbon was stripped in the existing desorption plant.

Jan 1, 1982

The Olympic Dam deposit is located some 600 km north of Adelaide in South Australia. It was discovered in 1975 by Western Mining Corporation and in 1979 a joint venture was formed with British Petroleum for the evaluation and development of the project. Studies were completed and construction started in 1986 with the plant being commissioned progressively between April and August of 1988. In 1993 Western Mining acquired BP's interest and are now owners of the whole deposit. The scale of the initial development was 1.5 Mtpa of ore for the production of 45 000 tpa of copper cathode, 900 tpa of uranium oxide and some gold and silver. Two expansion programs have occurred in 1992 and 1995 and current performance is at the rate of 3 Mtpa of ore for the production of 84 000 tpa of copper cathode, 1500 tpa of uranium oxide, 24 000 oz per year of confined gold and 380 000 oz per year of confined silver (Table 1). An aerial view of the plant is shown in Figure 1. The benefit of diversifying into the production of more than one product is undoubted and the flexibility of being able to produce variable quantities of copper and uranium also allows advantage to be taken of a change in market conditions.

Jan 1, 1996

By Pell D

Mechanical cleaning of coal was porforined in a few small plants in New South Wales from 1577 brit the first large coal washeries were built by Broken Hill Wbprietary Company Limited and Australian Iron and Steel Pty. Limited in the late 1940's. Mechanization of colleries in the 1950bs was abcomp" anied by construction of many coal washing plants and in the 1960's the growth of the coal export trade gave further impetus to the coal preparation industry. Design of coal preparation plants in Australia is modelled on practice overseas. Planning of a new plant in- volves investigation of many factors both technical and economic and the preparation of a specification by the operator for the designer's guidance. A wide range of preparation processes and equipment is on offer, but the nature of the coal to be treated and the separating efficiency desired usually dictate process selection. Simple or moderately difficult separation can be achieved with jigs, shaking tables or water washing cyclones. Coal which is difficult to treat or which has to be cut at a specific gravity lower than 1.5 is normally washed in a heavy medium process. In large plants it is usual to separate the coal into large, small and fine fractions and concentrate each fraction in a circuit designed to suit the grain size handled.

Jan 1, 1969

THE following paper is a description of the plant and operations of the above company in their recovery and treatment of the quartz tailings deposited as final residues by the various mining companies. at Waihi, Karangahake, and Waitekauri into theOhinemuri River. During the past few years the silting of the Ohinemuri River has increased to such an extent as to cause considerable interest and discussion, and has lately been the subject of a most extensive inquiry by a Royal Commission, to consider the best means of dealing with what is generally spoken of as a public nuisance.Ever since the commencement of mining in this district, which was opened as a goldfield in 1875, the various mines operating have been discharging their tailings into this river, it having been proclaimed a sludge channel in 1895. Up to the year 1900 the quantity of quartz crushed was not large, probably not exceeding 500,000 tons; but since that date the annual tonnages discharged have increased enormously, and at the present time would total from 550,000 to 600,000 tons per year. Records show that up to the end of 1910 at least 5,000,000 tons have been crushed, for an actual yield of bullion considerably exceeding £10,000,000 in value, and all the valuable tailings from...

Jan 1, 1911

The torsion test is considered as the best test used when the part is subjected to static or dynamic torque. Many published papers have investigated the torsion of non-heat treated metals. However, very few published papers dealt with the torsion behaviour of heat treated metals. The aim of this work was to study the effect of heat treatment on the torsion behaviour of steel alloy (AISI 01), which can be used for manufacturing small and medium drills, taps and reamers. The diameter of specimens used was 15 mm. The metal used was heat treated under different conditions, then torsionally tested. The results of torsion test were divided into two groups: results obtained during elastic limit from which the shear stress, shear strain and modulus of rigidity were calculated, while from the results obtained during plastic limit the plastic depth was calculated by applying derived equation when the angle of twist was more than yield value. The results obtained indicated that the value of hardness alone is not sufficient to establish heat treatment conditions. Rather, it was found that the determination of plastic depth together with hardness can help in the establishing of the optimum condition which was hardening temperature of 820¦C, hardening time 20 minutes and tempering temperature 220¦C. This condition produces hardness of 60 HRc and plastic depth of 2.5 mm.

Jan 1, 2003

By Kissell F. N, Volkwein J. C

The U.S. Department of Interior's Bureau of Mines has the opportunity to visit many U.S. mines, including some that claim 2 to 5 times the national average of 334 raw tonnes/unit shift (tps) from a continuous miner section. In a project to assess the reasons for this high production, the Bureau conducted two studies. The first study focused on the 25 highest producing continuous miner sections. What stood out during the visits-was the quality of the labor-management relations. In each of the mines there was a positive labor/management relationship based on mutual trust and a sense that the employees were the company's most valuable resource. Discussions with labor revealed a universally positive attitude toward the company. Interviews with the mine superintendents invariably ranked the quality and attitude of workers as more important than anything else. Also during the mine visits of the 25- mine study, no engineering factors obviously stood out. Time at the face was greater than average, most were in coal over 1.52 m and the roof was generally good. Also, none of the 25 mines had to contend with high methane levels. Because this study found that a high percentage of mines were in seams less than 1.52 m thick, the second study examined thin seam mines only.

Jan 1, 1988

Characterising the weight percentage of each mineral in base metal ores is an integral part of assessing the quality of an ore in terms of its processing properties. The Rietveld method, which uses X-ray diffraction data, has been applied to routinely quantify the minerals in lead/zinc and copper ores from Mount Isa Mines Limited and supergene copper ores from Ernest Henry Mining as well as their related products from the concentrators. The Rietveld method has been tested by comparing Rietveld mineral data with a standard sample with known mineral weight percentages and comparing Rietveld mineral data with mineral data calculated from elemental assays where the element only exists in one mineral such as lead in galena. Where this latter situation does not occur, the Rietveld method has been checked with both elemental and optical microscope data. In all cases, there is a good correspondence between the Rietveld data and the data it was checked against with absolute differences generally in the range of 0.5 to 3 wt per cent. The Rietveld method generally quantifies all minerals occurring over 1 wt per cent in one analysis and is less expensive and more routine compared to traditional methods such as optical microscope point counting. The Rietveld method can be applied to many stages of the mining cycle such as exploration, feasibility studies, mining, minerals processing and for environmental studies.

Jan 1, 1998

By Wakamatsu DT, Nakahiro Y

This present paper deals with the fundamental study of the separation of fine cassiterite and quartz by liquid-liquid extraction using iso-octane as an oil phase, dodecylamine acetate (DAA) as a collector, and sodium chloride as a depressant. With regard to the distribution of fine cassiterite and quartz between oil and aqueous phases, the effect of DAA has been investigated in terms of pH, DAA and NaCl concentrations, zeta potential, and adsorption density. From the results of the experimental work, a maximum recovery of cassiterite in the oil phase was obtained with pH around 6.0, DAA concentration of 1.0 x 10-5 mole/litre, and NaCl addition of 0.1 mole/litre. In these conditions of liquid-liquid extraction, most of the fine quartz remained in the aqueous phase. Thus it was found that NaCI was an effective depressant for fine quartz under optimum conditions. A series of separation tests by liquid-liquid extraction was then conducted for the mixed samples (6.0 per cent Sn) of cassiterite and quartz. By a single separating process, the per cent of recovery of cassiterite in the oil phase was about 92 per cent with a grade of 27 per cent Sn. The same results could also be obtained by using kerosene in place of iso-octane as the oil phase.

Jan 1, 1993

By S Miller, R Smart, J Thomas

Single-addition and sequential net acid generation (NAG) experiments were carried out on natural and prepared samples with varying contents of organic matter and pyritic S. Results show that carbonaceous matter can produce significant quantities of organic acids during peroxide oxidation in the NAG test, which leads to overestimation of acid-forming capacity and misclassification of benign samples as potentially acid forming (PAF). Organic matter effects were most pronounced in samples with low S (less than 0.5 per cent) and total organic carbon (TOC) contents of greater than seven per cent. The single-addition NAG test will tend to overestimate acid potential in samples with little or no pyrite and high organic matter content, potentially leading to sample misclassification. High pyritic sulfur samples tend to show little difference in single-addition NAG acidities with increasing organic matter, and it appears that pyrite is preferentially oxidised by peroxide when present in significant concentrations (greater than one per cent pyritic S). In sequential NAG tests overestimation was greatest in samples with little or no pyrite, but highly carbonaceous (>20 per cent TOC) pyritic samples were affected in later stages as the pyrite was depleted. A modified NAG method is proposed to account for the relative proportions of pyrite derived acidity and organic acidity in a given NAG solution.

Jan 1, 2003

By L Wsrell

During recent years the iron ore industry has experienced a continuous consolidation trend following increased merger and acquisition activities. Analysing and evaluating these mergers is important in order to establish potential effects. The purpose of this paper is to analyse the price effects caused by the merger between Rio Tinto and North Ltd in 2000. The merger was cleared by the European Commission, as well as the Australian Competition and Consumer Commission, shortly after its announcement. The analysis will be conducted using a simulation model based on a proportionality calibrated almost ideal demand system, which uses the premerger situation in order to estimate the post-merger outcome. The relevant market is defined using shipments data. This is followed by the simulation model applied to the defined relevant market. The results show that the concentration on the market, given by the HHI, increases approximately 15 per cent, and that the market share of the new companyÆs reaches almost 20 per cent. Compared to the CommissionÆs assessment the results indicate a more concentrated market and thus a higher concern for possible competitive effects. Furthermore, the results suggest that the predicted average market price increase from the merger is 1.6 per cent. However, the merged firm is able to increase their average price by 5.1 per cent.

Jan 1, 2005

The Mons Cupri Cu-Pb-Zn deposit is situated within a complex Archaean volcanic sequence dominated by rhyolitic fragmental rocks. This sequence is underlain by a 150 m group of rhyolitic ash flow tuffs with minor conglomerate and sandstone, and is overlain by approximately 180 m of dacite and andesite flows. The Mons Cupri sequence itself consists of several elongate or circular rhyolite domes, flanked by rhyolitic fragmental rocks ranging up to 400 m in thickness away from the domes. The lithology of clasts (typically 1 cm to 1.5 m in size) provides strong evidence that the flanking fragmental unit was derived by explosive eruptions associated with the rhyolite domes. An approximately 15 m thick shale horizon, bleached and silicified at its base, overlies both the rhyolite domes and the frag- mental unit. A south-dipping chloritic pipe-like body, with near-surface dimensions of 1,000 by 250 m and narrowing at depth to produce a cone-shaped cross section, lies within the rhyolitic frag- mental rocks about 250 m north of the largest rhyolite'dome in the Mons Cupri vicinity. Its east west elongation parallels that of the rhyolite dome. Ghost fragments indicate that the material in this fissure is a severely chloritized derivative of the rhyolitic frag- mental unit. The chloritic pipe is overlain

Jan 1, 1973

In the Renison Bell area of western Tas mania, a series of Lower Cambrian quartzites, shales, carbonate beds ("dolomites"), cong- lomerates, tuffs and argillites have been folded into a broad monocline whose general strike is NW-SE, plunging slightly north and dipping NE. The downwarped eastern side of the monocline is disrupted by a steep (50-800) east dipping normal fault, known as the Bassett Structure, whose throw is in excess of 500 m. A series of flat north dipping normal faults, each with a throw of approximately 50 m, further disrupts the sequence. All major faulting was pre-mineralization. A cassiterite- bearing Devonian quartz porphyry body intrudes this Cambrian sequence 2 km south of the currently operating mine. Of economic importance is the presence of three carbonate beds in the sequence. These carbonates consist of a mixture of calcite, dolomite and siderite. The No. 1 (youngest) and No. 2 carbonate beds are each approximately 15 m thick and are separated by 20 m of hematitic conglomerates and tuffs. The No. 3 (oldest) carbonate bed is approximately 5 m thick and is separated from the No. 2 horizon by 50 m of dark grey, finely laminated shales and quart- zites. Whilst the carbonates are remarkably persistent over at least 30 km2, facies changes are common and as a result of these changes, the carbonates vary considerably in

Jan 1, 1973

By K Kuganathan, Y Potvin

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: a minimum filling rate of 250 m3/h, a curing time of 28 days, and minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

Gold was discovered in the Bendigo area of Victoria in 1851 (Willman and Wilkinson, 1993), and all the early gold mining of any note involved washing (puddling) the gold out of the regolith or alluvium. The waste material from this process was a semi-fluid mixture of rock debris, soil and water, referred to as `sludge'. Puddling machines were gradually introduced to speed up the puddling process (Cole, 1994), and by 1855 an estimated 2000 machines were in the district (Anderson, 1978). In 1859 it was estimated that approximately 2 293 000 m3 of material was puddled annually by the machines on the eastern side of the goldfield, whose waste drained into Bendigo Creek and its tributary gullies. It was also estimated that after the gold was removed, approximately one-quarter of the residue/sludge consisted of the heavier, coarse-grained material which settled out fairly quickly, while the remainder, approximately 1 720 000 m3, was the fine-grained material which flowed downstream for some distance (VPP, 1859 - 60). From these figures it can be assumed that for the ten years during which this volume of puddling was maintained (1854 - 1864) over 5 700 000 m3 of gravels and sands and 17 200 000 m3 of fine-grained sludge had been discharged into and around Bendigo Creek. This was enough to cover an area of over 400 km2 to a depth of 5 cm. By 1859 the problems associated with the sheer volume of sludge being discharged were such that a Royal Commission was appointed to `Enquire into the Best Method of Removing the Sludge from the Gold Fields' (VPP, 1859 - 60). The goldfields referred to were those in the Bendigo area around the township of Sandhurst (now known as Bendigo). The Report of the Commission (VPP, 1859 - 60) stated that: `... inspection of the country bordering upon the course of the Bendigo Creek, to a distance of about fifty miles from Sandhurst . . . ' had revealed that the sludge had ' . . . filled up watercourses and flooded pasture lands . . . '. It also noted that ' . . . even on the plains, thirty or forty miles away from Sandhurst, where the sludge flows thin, and is relieved from its heavier particles, we found it baked into a perfect concrete, and in thicknesses varying up to two feet or more . . . '. The italics were used for emphasis in the original text. As it was considered unlikely that the physical evidence for such widespread inundation would have disappeared completely over the intervening 130 or so years, a project was initiated to locate any evidence of the inundation in the current landscape. If such evidence were to be found, then an estimate could be made of both its extent and its effects on the topography, drainage, and land-use of the inundated area. Extensive field work has determined that over 700 km2 to the north of Bendigo was inundated by the sludge. The area has not been uniformly covered, but has occasional `inliers' which have obviously escaped inundation by being slightly higher than the surrounding areas. Today the sludge is readily identified as a very fine-grained, hard-setting, concrete-like `capping' overlying a well-developed, well-structured, pedal horizon, or in some instances, the gravels and sands of a creek bed. The thickness of the sludge capping varies between a few centimetres and three metres (Peterson, 1996). The buried topography was gently undulating, in direct contrast with the almost unnatural flatness of

Jan 1, 1997

By P J Savory

Ranger is a uranium mining operation located within one of the most environmentally sensitive regions of Australia. Geology has played an important role in mine planning, operations and rehabilitation since discovery of the deposits 25 years ago. The Ranger orebodies have a reserve total of 166 300 tonnes of U308 including 90 400 tonnes of U308 at North Ranger. At current milling rates these reserves give a mine life greater than 40 years. The uranium is hosted in Lower Proterozoic rocks of the Cahill I ormation and is associated with strong chlorite alteration. In pit grade control involves the use of calibrated probes and a radiometric truck discriminator allowing fast, accurate grade determination of material. Ore is defined at a cut-off grade of 0.2 per cent U308. Mineralised material is defined by the Uranium Mining (Environmental Control) Act 1979 (UMEC Act) at a grade of 0.02 per cent U30s. Natural water levels in the #1 Pit area vary as much as 7.5 metres between wet and dry seasons. Ground water inflow into the pit during the dry season is 600 m3/day. No significant slope failures have occurred in the pit. The environmental impact of mining operations is constantly monitored. Rehabilitation of non-mineralised stockpiles is ongoing. This paper discusses the interaction between geology, hydrogeology, rock mechanics and grade control with the present mining operation.

Jan 1, 1994

By J R. Robinson

Prior to mine development, exploration drilling within the Luise Caldera on Niolam Island encountered gold mineralisation to the northwest of the main Minifie and Lienetz orebodies. This mineralisation was referred to as the Kapit orebody, and ten diamond drill holes were subsequently completed over the area to investigate its economic potential. Several significant mineralised intercepts were returned. These were interpreted using the orebody model developed for Lihir at that time which invoked a strong horizontal control to mineralisation. Additional consideration was given to the elevated geothermal temperatures encountered, the proximity of the mineralisation to the ocean, and its perceived depth below sea level, resulting in the Kapit area being given a low priority for follow up investigation. As a result, no further work was completed over Kapit until recently. The Kapit orebody was the target of an intense diamond drilling programme during 2002/2003. Data from this latest round of drilling has significantly improved understanding of the mineralisation and associated geology. The significant orebody now delineated at Kapit substantially differs from past interpretations, and the latest data has upgraded its economic potential. A resource estimate and other critical studies completed in 2003 enabled an updated reserve statement to be issued in February 2004 including the Kapit mineralisation for the first time. Total Probable Reserves at Kapit stand at 25.2 million tonnes (Mt) at 5.28 grams of gold per tonne (g Au/t), for a total of 4.3 million ounces (Moz) of contained gold.

Jan 1, 2004