Search Documents

By Belton G. R

The kinetics of the interfacial reaction of H2O on liquid silica-saturated iron silicates has been studied by means of measurement of the HDO-H2 isotope exchange reaction. The apparent first order rate constant, ka, was found to be inversely proportional to the H20/H2 ratio, consistent with two electron (melt to adsorbed/dissociating molecule) transfer mechanism and can be given by the expression In ka = -1.97 x 104/T + 1.57 - ln(pH2O/pH2), where the units for ka are mol cm -2 s-1 atm 1. The results of the current study are shown to be consistent with the indirect measurements of earlier work.

Jan 1, 1987

By G J. Keyter, P J. Terbrugge, Yu Xianb

There has been disappointingly little development in the understanding of the behaviour of rock slopes in open pit mines over the past 30 years. The lack of development in general, and of robust, standardised approaches in particular, are surprising in view of the æultraÆ deep open pit mines that are being developed to depths in excess of 1000 m. Research has recently been carried out into the occurrence of zones of extension strain in open pit slopes. This showed that very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. Results of the research will be presented for different slope heights, slope angles and horizontal to vertical in situ stress ratios. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning, producing easily measurable seismicity. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. Case studies of slope failure in two open pits will be described. In both cases failure occurred æsuddenlyÆ after very limited amounts of deformation. In the first, the slope crest moved suddenly upwards and backwards over a length of more than 200 m, with associated instability. In the second, the horizontal displacement of the slope face was almost an order of magnitude greater than the vertical displacement and occurred æsuddenlyÆ. A recently installed seismic system is detecting events in a significant zone behind the slope face. Both pits were in the 200 m to 300 m depth range at the time of the occurrences.

Jan 1, 2003

By N Davies, M J. Coward, P L. Hissey

Mount Isa Mines has four mining operations in Mt Isa with the X41 and Enterprise Mines producing copper and the Lead Mine and George Fisher producing lead zinc and silver. Each stream contributes ore to their respective concentrator at a feed rate and therefore metal ratio set out by the monthly schedule. Mine Planning and scheduling lead to a sales and operating plan (S&OP) and revenue projections which ultimately derives actual revenue /tonne and therefore cost/tonne. At Mount Isa, both the copper and lead/zinc streams produce ore from relatively new operations to be blended with material from more mature operations. It is critical to accurately predict the metal contribution from each operation in order to gauge the relative performance of each mine. Development mining ore contributions are estimated and reconciled, as are stope and bench sources. Performance is continually measured and assessed during extraction and grade adjustments are made to account for underbreak, overbreak and design modifications. It is critical to not understate or overstate the contribution from one operation relative to the other as this can produce a false picture of operational performance. Identifying process improvements are key to improving the business overall. Ore from the lead stream passes 17 measurement stations and two midstream reconciliation points before delivery to the heavy media plant (HMP), where the metallurgical circuit begins. From this point two concentrates are produced. A zinc concentrate for treatment off site and a lead concentrate for further on site processing. The lead smelter takes 100 per cent of Isa concentrates as well as a contribution from BHP-BillitonÆs Cannington Mine.

Jan 1, 2002

The mining. operations of Bougainville Copper Pty Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea. Mineralisation in the Panguna area was first established by C.R.A. Exploration Pty Ltd in 1964. Exploration work since then has established ore reserves estimated to be 760,000,000 tons of.0.47% copper and 0.4 dwt./ton gold. An economic feasibility study completed in July of this year has enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons per day. The concentrate will be pumped as a slurry through a 15 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 megawatt steam power station, and access roads.

Jan 1, 1970

Recent and on-going studies on the leaching of gold, the properties and activity of carbon, developments in the elution of gold from carbon, and methods of recovering gold from solution are reviewed. Emphasis is placed on Australian contributions, and their impact on gold metallurgy. Consideration is given to the future development of selective solvent extractants, ion exchange resins or alternative reagents for cyanide.

Jan 1, 1987

By Lukaszewski GM

The indiscriminate surface disposal of coal waste in the past has created a serious fire hazard in the bush of the northern New South Wales coalfields. Spontaneous or bushfire-induced combustion in large neglected dumps of this material has increased in recent years causing a rise in air pollution. Surface methods of coal waste disposal are still being practised, and in many cases new material is being added to old dumps, many of which are burning. CSI RO has conducted research on methods of preventing and controlling fires in coal waste and recommends practical methods of overcoming these problems. Some laboratory and on-site investigations are described and the hazards of improperly constructed dumps are considered. The available techniques of fire prevention and control are discussed in relation to Australian conditions. Proposals for the safe and economical disposal of coal waste are outlined.

Jan 1, 1970

By Hutchings SG, Skimmings T

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

By Beeby C. j, Fernando W. J, Ming M. Q I, Guang Li Xi

Removal of moisture in steam-fluidized, mainly steam-heated, fluidized beds makes possible significant energy savings over conventional forms of large-scale drying. The systens are described and their applications to brown coal and alumina hydrate are reviewed. In application to brown coal the use of the system to permit meeting diurnal variation in power station output, and the use of triple-effect drying to minimise coal usage and to avoid the necessity of recovering in the turbines the energy in the steam from the last dryer are discussed. To facilitate the rapid adoption of the systems proposed, studies are being made of heat-transfer to dried coal, of moisture equilibrium in pressurized and vacuum systems, of tapered beds as a means of reducing carrier steam and permitting wider size variation, and of the use of carrier solids for drying lump materials.

Jan 1, 1989

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2005

By Lunarzewski L

Gas problems, largely instantaneous outbursts of coal and gas, arose in the early days of coal mining in Australia, leading to attempts at predrainage often including destressing. With deeper mining and new gassy areas being mined, gas problems have increased. This has led to more research, such as into coal-gas relationships, and more practical trials into seam gas drainage in both the Sydney and Bowen basins. Predrainage techniques have been devised to suit the special Australian geological conditions and to take into account the erratic occurrence of CO, (nearly 100 per cent in some cases) in the seam gas. Better mining methods and other improvements are continuing. The introduction of post-drainage has been simplified by the adaptation of long established overseas techniques and equipment.Utilisation of seam gases in Australia is complicated by the presence of CO, but even with pure CH. little has been done.Seam gas drainage has some disadvantages such as the need for, and the dangers of, complex and rigorously controlled plant. Also drained coal becomes harder and dustier.

Jan 1, 1985

By Ellson I. G

Shay Gap was created for the sincrular purpose of housing, in comfort, the workforce that would be required to mine iron ore, from leases held by Goldsworthy Mining Limited, in hill country, approximately 170 kilometres east of Port Hedland in the Pilbara region of Western Australia. To combat the and environment, the Company ultimately decided to adopt a novel planning concept for the town, which had not been attempted before in Western Australia. The special problems encountered during planning, and the reservations that were expressed during construction and early settle ment, are now part of the dim past. During the three years of occupation now achieved, there has been accumulated a story of success in the provision of an acceptable alternative to modern suburbia. Not only may this be claimed, but it can also be argued that the Shay Gap concept has been a more successful solution to a real environmental problem in our arid Pilbara region than has been seen in other similar settlements.

Jan 1, 1976

By A Bonani, R Molina, H Constanzo

With conventional undercutting sequence the infrastructure on the production level often has a short serviceable life before major rehabilitation is necessary and is characterised by high maintenance costs. The abutment stress zone is the main cause of this situation. The application of the pre-undercut caving method variant can increase the availability and utilisation of the production level When a pre-undercut is used development and construction are carried out underneath a previously undercut area, far away from the abutment stress zone, under more favourable stress conditions. This paper describes the design principles and the relevant results from the application of the pre-undercut variant over three years to the Esmeralda sector of El Teniente mine. The aspects described are the undercut-extraction, the undercut-development and construction distances, the geometry and drawbells opening, cave extraction rates, and the rate and height of undercutting.

Jan 1, 2000

I WISH to express to the members of the Institute my sincere appreciation of the distinction which they have conferred upon me by again making me their president. It also gives me great pleasure to once more welcome the Institute to Mount Lyell.Since your last visit certain improvements in plant have been made, which I trust you will have found interesting, and which show that, though located in a remote corner of the world, we are abreast of the times.The opportunities which a recent lengthy trip to America has given me to observe the degree of interest which our local smelting practice continues to arouse in metallurgical circles make it seem appropriate that I should take advantage of your visit to lay before you some detailed information on the more practical features of pyrite smelting, particularly as carried out at Mount Lyell. There are only a few places in the world where the method is now being practised in approximate purity-only about half...

Jan 1, 1915

By B J. Hutchison, S Gannon, J Chambers, D Oko-oboh

The Kanmantoo copper mine is located in the Adelaide Hills area of South Australia and is owned and operated by Hillgrove Resources (HGO). The mine is a drill and blast, truck and shovel operation mining sulfide (chalcopyrite) ore located in chloritised andalusite biotite schist. The initial Kanmantoo open pit operation occurred in the 1970s, before falling copper prices closed the mine. In 2010 the mine was reopened by HGO and the Kavanagh cutback of the Kanmantoo pit was undertaken. The Spitfire, Nugent and Emily Star satellite pits were also mined through to 2015 before the latest steep wall Giant pit design was developed to take mining out to 2019.There are no major fault structures and only two significant shear zone structures exposed in the open pit walls. The main Garnet Andalusite Biotite Schist (GABS) unit is quite competent so the pit designs have therefore mainly been controlled by four distinct joint sets. This paper is a case study on the influence of the joint regime on the wall stability of the main GABS unit and how a better understanding of the joint regime and the use of rock reinforcement has allowed the steep wall design to be adopted.The paper also describes the remote geotechnical mapping and slope monitoring techniques used to manage the rockfall risks associated with the steep walled slope design.CITATION:Hutchison, B J, Chambers, J, Gannon, S and Oko-oboh, D, 2017. Case study of joint structure and the design and performance of open pit walls at the Kanmantoo copper mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 355–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By B E. McCarthy

Red Dome Mine was a highly complex gold copper operation developed over a number of phases between mid-1986 to October 1997. With only three years of production ahead at any time, a proactive practical approach to mine closure was necessary. In 1989 the Domains Concept to life-of-mine planning and mine closure was created as a response to the proposed changes to legislation.The Domains Concept, a relatively simple idea developed to integrate mine closure during production at Red Dome, has been broadly adopted by both government agencies and industry in the intervening 20 year period. Over time the author has observed that the concept has been poorly applied, misunderstood and in some cases even misrepresented. As a consequence, the potential opportunities from applying the concept, including the optimisation and minimisation of life-of-mine costs, mitigation of long-term financial liability exposures and building credibility with the general community, have been missed.This paper examines the many benefits, advantages, applications and perceived barriers to developing and integrating a fully costed life-of-mine plan. Integrating the Domains Concept early in the project, within the operational budgeting, allows the production of a meaningful and useful document, representative of a whole life-of-mine, cradle to grave, with measurable rehabilitation and closure outcomes when the concept is used to full effect.The Domains Concept serves to optimise cost-effective, whole of mine, life cycle planning which provides beneficial outcomes for the community, significantly mitigates legacy issues and contributes to the attainment of compliance and sustainability principle objectives.CITATION:McCarthy, B E, 2014. The domains concept – 20 years on retrospective, obstacles and opportunities for effective life-of-mine implementation, in Proceedings Life-of-Mine 2014 , pp 621–636 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By A R. Bonani, M P. Pe±a

The optimisation of slope angles, that is to say, increasing them, compared to the original design is always the subject of analysis of stability for geotechnical engineers and economic analysis for planning engineers. Questions to be answered include: What is the acceptable risk? What factor of safety? What probability of failure or reliability? The Rosario Open Pit has a history of failure, poor quality rocks and high pore pressures. It was decided to deepen the pit below the programmed design to test the practicality of different design approaches, which if successful, could be used to improve the economics of mining at Collahuasi. The revised slope design has factors of safety in the range of 1.0 to 1.2, probabilities of failure of ten to 38 per cent, and increased slope angles of between 3¦ and 5¦ with respect to the original design. The pit deepening with these design slopes will deliver an extra two million tonnes of ore which will have a significant positive impact on mining economics.

Jan 1, 2007

Recent analysis of backfilling material has shown that a finer size distribution is preferable for stope filling. In order to increase crusher throughput and pit productivity, a reassessment of the quarrying operation was conducted. Part of that reassessment was a review of blasting practice. Six means of reducing the average muckpile fragment size were examined. Different blast initiation and charging options were compared, and patterns using smaller hole sizes were designed, analysed with the JKMRC 3x3o software, then drilled and fired. The ground vibration and face movement was recorded and compared. To determine whether the Kuz-Ram model could be used in an economic analysis of the quarry operation, the fragmentation distribution of the small diameter hole blasts was determined. Photographs of the muckpiles were taken and digitised. However subsequent analysis indicated that a satisfactorily large photo sample was only obtained from the smallest diameter hole blast. The Kuz-Ram fragmentation model prediction was found to be within the confidence limits of those results. An engineering and cost comparison between the blasts was made.

Jan 1, 1995

By Stone I

Tahmoor Mine is located in the southern Sydney Basin 80km south-west of Sydney and produces 1.2 MT of Bulli Coal annually. Bord and pillar methods used to date will be supplemented by a longwall system. Difficult roof conditions have been experienced since mining began in 1979. A dominantly horizontal stressfield promotes shear failure in the thinly interbedded roof sequence of shales, laminites, siltstones and fine sandstones. General roof conditions and failure characteristics are related to the angle between the roadway direction and the principal horizontal stress direction. The apparent stressfield changes direction, magnitude and the ratio of principal horizontal components across the mine workings in response to both in situ and mining induced causes. Initial roof support of 5 x 2.1 m bolts per W-strap at in intervals, with mesh, was upgraded to include RSJ's in order to support areas of failed roof. This support system was inefficient and costly. A third system of support emphasizes roof reinforcement with full resin encapsulation of 2.1 m bolts in W-straps. The number of bolts per strap (6-8), extra butterfly straps and bolts, and W-strap spacing is determined for each area by expected roof and stress conditions. Intersections are pre-bolted and ribs are supported in some areas. Pillar dimensions, order of drivage and roadway width have each been altered to improve roof control. The intensity of roof deformation at the face varies from panel to panel and causes development rates to decrease to 30% of the maximum. 1. Manager, Tahmoor Mine, Tahmoor, N.S.W. 2. Senior Geologist, BP Coal, Picton, N.S.W. Roof conditions in each area of the mine are characterised and then projected to future development areas based on the relationship between stressfield orientation, relative roadway direction and face conditions. Planning information available includes expected development rates, roof support requirements and areas of changing conditions. Future improvements of strata control involve defining support design parameters for the range of mine conditions already seen at Tahmoor.

Jan 1, 1986

By Marshall K. I

THE problem of satisfactorily eliminating the fumes and dust which are unavoidably produced in various metallurgical and manufacturing industries is one which has received considerable attention in the past, and has been the subject of much investigation and research. The solution of this problem was urgently desired for two reasons, the principal one being the fact that a considerable percentage of the total process losses in many industries was represented by the commercial values of the fumes and dust that escaped from the stack.The other reason is that, in some instances, the emission of the matter is regarded as objectionable. Various methods have been designed with a view to solving the problem thus presented, and the latest development that has beendesigned is the process of electrostatic precipitation. Continued investigational and developmental work with this process has already demonstrated its applicability to many industries, and new uses to which the process can be put are being opened up. Its use is already widespread, and the economic success that has attended its application in most instances would indicate that its use will become more general in the future.It has proved its ability to treat gases over wide ranges of temperature, and has successfully handled various types of fumes whose chemical characteristics differ very considerably. In many processes it has now come to be regarded as standard equipment.HISTORY OF ELECTRICAL PRECIPITATIONThe first recorded observations on the influence of an electrified insulated wire on gases containing solid particles in suspension was made as early as 1824 by Hohlfeld, in Leipzig. He found that, if he electrified a wire hung in a bottle filled with smoke, the smoke cleared rapidly, and a deposit formed on the sides and bottom of the bottle.

Jan 1, 1923

For too long we, as an industry, have borne the brunt of irrational claims, poor science and even worse, journalism with regards to our affect on the environment. To some of us, the overwhelming media attention on greenhouse warming, the polluting outputs of mineral processing or unthinkable depletion of natural resources has left us embarrassed and more unfortunately has turned bright young people away from a career in the minerals industry.This paper shows the hypocrisy associated with an element of the green movement and dispels some general myths on mining disseminated by radical environmentalists.The fallacy of the greenhouse warming effect will be scrutinised by common sense and the mining industryÆs use of land will be discussed and put in proper perspective.Problems associated with safety and emissions and the means to overcome such are discussed briefly.

Jan 1, 2004