Search Documents

By Roland Kammel

For electrolytic recovery of silver from dilute aqueous solutions improved mass transfer is necessary to achieve favourable current efficiencies and high space-time yields. The many cell designs proposed for this application can be divided into two different groups: cells from which the silver must be redissolved and cells from which the deposit can be reclaimed as a metal. Introduction Electrolytic silver recovery methods have proven advantageous under technical and economic aspects for the treatment of rinse water, still rinses and spent silver solutions in the electroplating and surface finishing industry, of exhausted fixing baths from photographic processing, bleed electrolytes from silver refining processes and leach liquors. Examples of the compositions of typical dilute silver solutions are listed in Table I.

Jan 1, 1984

By H. H. Johnson, Eric W. Johnson

A newly developed ac technique was used to measure the electrical-resistivity changes associated with both cyclic stressing and subsequent annealing of high-purity and OFHC copper. The early stage of push-pull fatigue was explored at 293° and 4.2°K, with stresses chosen for an expected fatigue life of 2 to 8 X 105 cycles. For high-purity copper, fatigue at 293°K was accompanied by an initial increase in resistivity. After about 5000 stress cycles, no further increase was observed. Annealing studies showed that the resisticity increment could be accounted for solely in terms of an increased dislocation density, to about 2 x 1010 disl pev sq cm. Fov 42°K fatigue, however, the resistivity increased continually, with no evidence of saturation, as approximately (No. of stress cycles)1/4. This is intevpreted to result from both dislocation multiplication and vacancy production; estimated vacancy concentrations are 10-4 to 10-9. The continuous resistivity increase was inhibited by interspersed annealing treatments at 293°K, which also raised the level of the stress-strain curve. These effects are attributed to annealing of vacancies into dislocation loops. In contrast, OFHC copper fatigued at 4.2°K showed saturation of electrical vesistivity after only a few hundred cycles, and it appeared that vacancies annealed out completely between 77° and 293°K. MaNY observations suggest that both dislocation multiplication and point-defect production are important aspects of fatigue deformation. An increase in dislocation density with number of stress cycles has been demonstrated or implied by several experimental techniques, including optical metallography with lithium fluoride,' electron microscopy with copper,2 thermal conductivity of Cu-Zn alloys,3 and peak-stress measurements during cycling at constant plastic strain amplitude.4,5 At low amplitudes and/or stresses saturation of fatigue hardening and dislocation density occurs early in the expected fatigue life,4-6 frequently by a few hundred cycles. The evidence for point-defect production is somewhat less extensive, but it is nonetheless persuasive. Rosenberg7 reported briefly that, for equal stresses, copper fatigued at liquid-hydrogen temperature displays an increase in electrical resistance some ten times that which accompanies unidirectional stressing. Further, the extra resistance saturates after a few hundred stress cycles, and does not anneal significantly until a temperature of about 170°K is attained.' Point-defect production during fatigue is also suggested by 1) the softening during cyclic stressing of initially strain-hardened polycrystal-line copper9, 2) the strong temperature dependence of the yield strength of fatigue-hardened mono- and polycrystalline copper,579"0 and 3) the influence of intermediate annealing upon slip-band formation in copper fatigued at 90°K.8 It is evident that characterization of the fatigued state requires a knowledge of both point-defect and dislocation densities. For this purpose electrical-resistivity measurements are useful, but they are difficult to perform because of geometric limitations. Push-pull fatigue is necessary to obtain a macroscopic ally uniform deformation over the specimen cross section; however, the specimen must then have a low slenderness ratio to avoid plastic buckling, while the standard dc resistivity technique requires a very slender specimen for

Jan 1, 1965

By W. E. Ruder

It has been pointed out by Stead1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly' well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Ar2. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703" C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750" C. for 0.5 per cent. Si to 860" for 6 per cent. alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730" and 750:. In the preliminary experiments, some of which have been described in a previous paper, it was found that practically all of these steels, when annealed to 1,200" C. or higher, showed grains of comparatively large size. These grains varied in size, however, from about 4 sq. mm. to 50 sq. cm. (see Figs. 1 and 2) under the same conditions of anneal, and it was for the purpose of determining the cause of this difference in size that the experiments herein described were undertaken. From a preliminary study of the chemical composition of the specimens

Jan 1, 1914

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

By A. G. Gilbert

Paradoxical is the word. The coal industry, despite reach- ing a 22-year high in production (590 million tons), has been tagged as having its back to the wall vis-a-vis its valiant attempts to quench the nation's still unabated craving for coal. What must be even more reassuring to the industry, infected once with rumors of a uranium takeover, is a nation's almost insatiable appetite for electricity. Between 1967 and the summer of 1970, utility stockpiles were being gobbled up, diminishing to 79% of the January 1968 level.

Jan 1, 1971

In order to assist in the building up of the industries and commerce of France, by cooperating with the Congres General du Genie Civil, the four Founder Societies have appointed the following committee: E. G. Spilsbury and Arthur S. Dwight representing the American In-stitute of Mining and. Metallurgical Engineers; George F. Swain and Nelson P. Lewis to represent the American Society of Civil Engineers; Charles T. Main and George W. Fuller to represent the American Society of Mechanical Engineers; Lewis B. Stillwell and Andrew M. Hunt to represent the American. Institute of Electrical Engineers.

Jan 12, 1919

By E. H. Timmerman, A. F. van Everdingen, J. J. McMahon

The prevent paper contains a method which combines the material balance equation' with the water influx equation' to obtain reliable values for the active oil originally in place and a quantitative evaluation of the cumulative water influx. The method is illustrated by an application to a reservoir without original gas cap. In the absence of an original gas cap. results may be obtained using only field production and pressure data, PVT analyses. and a minimum of subsurface information. CHARACTERISTICS OF RESERVOIR AND RESERVOIR FLUIDS Production in the field under review is obtained from the top of the Wilcox formation of Eocene age, at a depth of approximately 8,100 ft subsea. The structural map, Fig. 1, shows that the accumulation, half elliptical in shape with the long axis in east-west direction, is trapped to the north and on the upthrown side of a normal fault. A number of east-west faults with additional minor faulting in random directions are found in the general area, and seismic information and production performance indicate in this particular case the existence of a second fault a short distance downdip, with a strike more or less parallel to the fault controlling the accumulation. It is estimated that 1,830 acres were originally underlain by oil and that the maximum thickness of the original oil column, about 37 ft, was only slightly greater than the maximum thickness of the oil-bearing sand. Maximum net sand thickness was estimated at approximately 26 ft. From logging and subsurface information the gross sand volume has been placed at 37.400 acre-ft. which reduces to about 27,500 acre-ft after probable non-productive intervals have been deducted. The following table presents laboratory analyse; data for the Wilcox sand cores. Average Average Samples Considered Permeability Porosity All Samples 236 md ..19.9percent Samples with k>l md 256 md 20.5 per cent Samples with k>8 md 275 md 20.9 per cent Interstitial water was estimated at 15 per cent. The initial gas-oil ratio was approximately 900 cu ft/bbl. and the initial shrinkage factor was determined by the laboratory to

Jan 1, 1953

By H. 0. HOFMAN AND W. MOSTOWITSCH

I. INTRODUCTION. THE mineral gypsum, CaSO, + 2 H2O, has been used for many years as a sulphurizing and basic flux in several smelting¬operations. Thus, in smelting oxide nickel-ore in the blast furnace, it is commonly added to the charge to furnish the sulphur necessary for collecting the metal in a matte, and a base for slagging the siliceous gangue. In the concentration of lead-copper matte in the reverberatory furnace it has been used for years at Freiberg, Saxony1 for a similar purpose, and for producing at the same time a copper-matte with less than 0.15 per cent. Fe. The latest use gypsum has been put to is in the blast-roasting process of Carmichael-Bradford.2 The term "blast-roasting," given by A. S. Dwight3 to the Dwight-Lloyd method of roasting and agglomerating ,I is a happy generic term which covers the ground better than the " lime-roasting" of Ingalls' or the " pot-roasting " of Austin,6 in that it leaves the operation independent of the character of the flux and the form of apparatus, and retains the characteristic feature of this class of processes-namely, that of using forced draft. In the Carmichael-Bradford process the dehydrated material, mixed with galena-concentrate, acts as a diluent and a flux. The process differs in this from the Huntington-Heberlein7 and the Savelsberg8 processes, in both of which limestone is used.

Jan 1, 1909

By C. H. Snyder

Tlie paper deals with details of construction of the Colmol, including improvements in design that will be incorporated in new models. These improvements are results of problems encountered and worked out in experimental operation with the unit. Also included is a descriptive plan of operating where roof and air conditions are of the worst. A summary of production results from the machine is presented. THE various units used in conventional mining are well-built. Generally the universal under -cutter, driven by approximately 50 hp, weighs approximately 25,000 lb, and is a very strong piece of machinery. The drilling machine is not as husky as an undercutter, generally is driven by approximately 15 hp, weighs about 9000 lb, but is a well-constructed, sturdy mechanism. The loader, usually 60 hp, weighs approximately 24,000 lb, and certainly is a strong, rugged unit. The working parts of all three of these sturdy conventional units have been made of tough steel alloys for some time. With the use of three machines having a combined horsepower of approximately 125, with a combined weight of approximately 60,000 lb, and with the possible inherent advantage of single purpose machines performing a single function, the use of considerable explosives has been required to complete the conventional mining cycle. It was therefore our thought, upon conception of the first Colmol,* a machine which was to do the work accomplished by the three conventional units plus explosives, that it must be a rugged mechanism. Now, after building several units, after going through many and varied experiments, and after the expense of some million-odd dollars, we find we have observed and learned nothing that contradicts our original thinking. A continuous miner, if it is to give satisfactory performance, must be a rugged piece of machinery. Ruggedness has been, and is constantly, in the minds of our engineers in designing the Colmol. Improvements where they have been required have been in the direction of more weight, more horse power, better alloys, bigger hydraulic pumps and motors; in short, always, toward more torque, greater strength, more ruggedness. Now not only the finest steel alloys are utilized but more than 100 Timken roller bearings are used. The following is some pertinent data on models being built and to be built: The low unit: Cutting height, 30 to 42 in. By changing the upper gear case the maximum cutting height can be increased to 61 in., giving a variable cutting height of from 30 to 61 in. Width of cut, 9 ft 6 in. Width of body, 75 in. over tracks. Height of body, 271/2 in. Overall length, 23 ft. Driven by three 50-hp motors or a total of 150 hp. Weight, 26 tons. The intermediate unit: Cutting height, 451/2 to 72 in. Width of cut, 9 ft 8 in. Width of body, 77 in. over tracks. Height of body, 43 in. Overall length, 26 ft. Driven by three 70-hp motors or a total of 210 hp. Weight, 35 tons.

Jan 1, 1951

By C. H. Snyder

Tlie paper deals with details of construction of the Colmol, including improvements in design that will be incorporated in new models. These improvements are results of problems encountered and worked out in experimental operation with the unit. Also included is a descriptive plan of operating where roof and air conditions are of the worst. A summary of production results from the machine is presented. THE various units used in conventional mining are well-built. Generally the universal under -cutter, driven by approximately 50 hp, weighs approximately 25,000 lb, and is a very strong piece of machinery. The drilling machine is not as husky as an undercutter, generally is driven by approximately 15 hp, weighs about 9000 lb, but is a well-constructed, sturdy mechanism. The loader, usually 60 hp, weighs approximately 24,000 lb, and certainly is a strong, rugged unit. The working parts of all three of these sturdy conventional units have been made of tough steel alloys for some time. With the use of three machines having a combined horsepower of approximately 125, with a combined weight of approximately 60,000 lb, and with the possible inherent advantage of single purpose machines performing a single function, the use of considerable explosives has been required to complete the conventional mining cycle. It was therefore our thought, upon conception of the first Colmol,* a machine which was to do the work accomplished by the three conventional units plus explosives, that it must be a rugged mechanism. Now, after building several units, after going through many and varied experiments, and after the expense of some million-odd dollars, we find we have observed and learned nothing that contradicts our original thinking. A continuous miner, if it is to give satisfactory performance, must be a rugged piece of machinery. Ruggedness has been, and is constantly, in the minds of our engineers in designing the Colmol. Improvements where they have been required have been in the direction of more weight, more horse power, better alloys, bigger hydraulic pumps and motors; in short, always, toward more torque, greater strength, more ruggedness. Now not only the finest steel alloys are utilized but more than 100 Timken roller bearings are used. The following is some pertinent data on models being built and to be built: The low unit: Cutting height, 30 to 42 in. By changing the upper gear case the maximum cutting height can be increased to 61 in., giving a variable cutting height of from 30 to 61 in. Width of cut, 9 ft 6 in. Width of body, 75 in. over tracks. Height of body, 271/2 in. Overall length, 23 ft. Driven by three 50-hp motors or a total of 150 hp. Weight, 26 tons. The intermediate unit: Cutting height, 451/2 to 72 in. Width of cut, 9 ft 8 in. Width of body, 77 in. over tracks. Height of body, 43 in. Overall length, 26 ft. Driven by three 70-hp motors or a total of 210 hp. Weight, 35 tons.

Jan 1, 1951

By R. E. Heithecker

Almost every oil well drilled into limestone formations in Kansas is treated with hydrochloric (muriatic) acid upon completion: to increase potential capacity of well and thereby increase its "daily allowable" production; to shorten time required to produce recoverable oil; and to increase quantity of oil recovered ultimately from reservoir. Acid treating marked a forward step in the producing fields of Kansas; in fact, many old limestone fields that almost had reached their economic producing limit were "rejuvenated" with acid and their capacities to produce increased several times. It also caused a marked increase in the ultimate oil recovery of some old and nearly depleted fields of Kansas. The effect of the acid was due to the cleaning-out action by the acid at the face of the limestone, the enlargement of the small drainage channels, and the apparent penetration of the acid to previously undrained porous and saturated strata. Studies of the effects of acid were made in the Fairport field, three groups of wells in the El Dorado field and the Shutts field. Estimation of increased recoveries resulting from acid in these fields and groups of wells ranged from 1000 to 2400 bbI. per acre. Limestone structures that had been tested by drilling and found noncommercial were later completed as commerical oil-producing formations through the use of acid. The Kansas City formation, Valley Center field of Kansas, is an example. Increased oil production and revenue from the old fields justified the reconditioning of equipment, which in most cases had become in poor mechanical condition. The first treatment with hydrochloric acid of an oil well in Kansas was in October 1932, and by the end of 1937 almost 6000 wells had been treated. Many wells were treated more than once and the total number of treatments exceeded 8000 by the end of 1937. Approximately 12 3/4 million gallons of acid was required for these treatments. The report includes 15 illustrations and 16 tables.

Jan 1, 1939

By R. E. Heithecker

Almost every oil well drilled into limestone formations in Kansas is treated with hydrochloric (muriatic) acid upon completion: to increase potential capacity of well and thereby increase its "daily allowable" production; to shorten time required to produce recoverable oil; and to increase quantity of oil recovered ultimately from reservoir. Acid treating marked a forward step in the producing fields of Kansas; in fact, many old limestone fields that almost had reached their economic producing limit were "rejuvenated" with acid and their capacities to produce increased several times. It also caused a marked increase in the ultimate oil recovery of some old and nearly depleted fields of Kansas. The effect of the acid was due to the cleaning-out action by the acid at the face of the limestone, the enlargement of the small drainage channels, and the apparent penetration of the acid to previously undrained porous and saturated strata. Studies of the effects of acid were made in the Fairport field, three groups of wells in the El Dorado field and the Shutts field. Estimation of increased recoveries resulting from acid in these fields and groups of wells ranged from 1000 to 2400 bbI. per acre. Limestone structures that had been tested by drilling and found noncommercial were later completed as commerical oil-producing formations through the use of acid. The Kansas City formation, Valley Center field of Kansas, is an example. Increased oil production and revenue from the old fields justified the reconditioning of equipment, which in most cases had become in poor mechanical condition. The first treatment with hydrochloric acid of an oil well in Kansas was in October 1932, and by the end of 1937 almost 6000 wells had been treated. Many wells were treated more than once and the total number of treatments exceeded 8000 by the end of 1937. Approximately 12 3/4 million gallons of acid was required for these treatments. The report includes 15 illustrations and 16 tables.

Jan 1, 1939

By AIME AIME

COMMITTEES. CENTRAL GENERAL COMMITTEE.-Wm. Fleet Robertson, Chairman; Win. M. Brewer,. Secretary. LOCAL COMMITTEE OF NELSON, B. C.-A. S. Farwell, Chairman; W. C. Bayly, Secretary; William Blakemore, M. S. Davys, S. S. Fowler, R. R. Hedley, Leslie Hill, A. H. Telly; W. C E. Koch, J. J. Campbell. LOCAL COMMITTEE OF ROSSLAND, B. C.-His Worship Mayor Hamilton, Chairman; AV. H. Aldridge, Charles Biesel, H. H. Claudet, F. W. Guernsey, R. Marsh, J. W. Astley, R. W. Brock, A. A. Cole, A. G. Larsen, R. H. Stewart. Also the Rossland Board of Trade, Robert Hunter, President; K. E. Mackenzie, Vice-President; A. B. Mackenzie, Secretary. LOCAL COMMITTEE OF GRAND FORKS, B. C.-His Worship Mayor Hammor, Chairman ; A. W. B. Hodges, A. L. White, G. M. Fripp, L. A. Manley, W. T. Spier, G. W. Wooster. LOCAL COMMITTEE OF VICTORIA, B. C.-Wm. Fleet Robertson, Chairman; William Al. Brewer, Secretary; Harold Grant, Thomas Kiddie, Clermont Livingston, E. C. Musgrave, W. J. Sutton, Francis A. Thomson. LOCAL COMMITTEE OF VANCOUVER, B. C.-C. F. Jackson, Chairman; His Worship Mayor F. Buscombe, J. J. Banfield, A. Bethune, John Boyd, H. C. Clarke, A. B. Erskine, E. P. Gilman, William Godfrey, W. D. Haywood, R. K. Houlgate, H. T. Lockyer, J. I. McAdam, H. M. McDowell, C. W. McMeekin, W. H. Malkin, F. Richards, T. J. Smith, George A. Walkem, G. Slieldon Williams. LOCAL COMMITTEE OF WHITE HORSE, Y. T.-Robert Lowe, Chairman.; T. W. Jackson, Secretary; George -Armstrong, A. L. Bindley, Rev. Father Corbeil, L. De Gex, A. E. Fisher, W. P. Grainger, P. D. McMillan, Rev. Mr. Main, George C. Mallot, Alfred Parre, George Pulham, George Reid, William Robinson, J. P. Scharschmidt, J. C. Schraeder, Major A. E. Snyder, Rev. Mr. Stringer, Judge George L. Taylor, William Taylor, H. Wheeler, E. J. White, J. P. Whitney;' ; LOCAL COMMITTEE OF DAWSON, Y. T.-Hon. W.W. B. McInnes, Commissioner of the Yukon Territory, Honorary Chairman; Major Z. T, Wood, Assistant Commissioner of the Yukon Territory, Honorary Chairman; J. B. Tyrrell, Chairman; J. Moore Elmer, Vice-Chairman; George Black, Secretary; Hon. Mr. Justice Dugas, Hon. Mr. Justice Macaulay, Hon. Mr. Justice Craig, Dr. Alfred Thompson, D. A. Cameron,. E. W. Griffin. The first session, held in the ministers' room of the Parliament Building, 3 p.m., Saturday, July 1st, was presided over by Past-President Robert W. Hunt. His Excellency the Lieut.-

Nov 1, 1905

By J. Fred Johnson

MORE ORE is mined in the Bingham District than in any other mining district in Utah. In addition to the open-pit operations of the Utah Copper Co., there have been, many large underground mines. Until recent years the principal production was from the Jordan and Commercial limestones, but in the last eight years valuable ore deposits have been developed in the so-called alphabetical or "A," "B," "C," and "D" limestones, mainly by the U. S. Smelting, Refining & Mining Co. The value of these developments has led the company just mentioned to acquire large holdings in the district and within the last year to install at the Niagara shaft a hoist capable of going to a vertical depth of 4000 ft., or 1800 ft. deeper than the present lowest level. Ore from Bingham has been the chief factor in enabling the

Jan 1, 1934

By Peter Allen, John R. Stuermer

COUNTRY RISK ANALYSIS A company operating in a foreign country assumes all the risks that it would at home. However, beyond these, it assumes risks that arise from the unique political economic, financial conditions of the foreign country which it operates. These risks are known as "country risks". The importance of these risks has grown appreciably in the recent past (particularly in the aftermath of Iran's revolution in the late 1970s and Mexico's debt rescheduling of 1982-83), and as a result, country risk analysis has become an increasingly useful management tool. Country risk analysis seeks to assess the probability that countries will service their aggregate foreign liabilities on time, as well as the probability that country conditions could inhibit the debt service capability of private sector debtors. This involves assessment of both the ability and the willingness of countries to meet their external liabilities in a timely fashion. "Ability" is linked economic and financial variables: principally, a country's economic structure, foreign exchange generating capacity and debt service burden. On the other hand, "willingness" is tied to political factors: mainly the economic/financial orientation of government policy and the stability of economic decision making. Ability: Economic, Financial Conditions and Prospects Judgement of a country's ability to meet foreign financial obligations begins with a detailed study of a country's external balance sheet which compares the country's foreign liabilities and assets. Table 1 below presents country balance sheets for Mexico, Korea and Indonesia. [TABLE 1 The External Balance 3-,-et 1983 (billions of dollars; Indonesia Mexico Korea Foreign Liabilities 31.1 67.6 40.5 By Source: Bank 13.1 75.5 26.3 Non-bank 18.0 12.114.2 Foreign Reserves 9.3 4.7 7.0] The large magnitude of Mexico's external debt (nearly $90 billion), compared to foreign assets of approximately $5 billion, illustrates the weakness of this country's external payments position, and the main reason that it has been unable to meet interest and principal payments and been forced to reschedule its foreign debt. On the other hand, the relationship between Korea's external liabilities and assets ($50.5 billion and $7 billion, respectively), is more favorable and helps explain why Korea has been able to meet debt service payments and maintain its access to the international capital markets. Indonesia has even a more favorable relationship between its foreign assets and liabilities, $31 billion and $9 billion, respectively, and its debt is mostly lower interest rate, non-bank debt, making for a less onerous debt service burden. After the balance sheet, the analysis turns to a comparison of the country's foreign exchange earning capacity and its prospective financing requirements, that is, the country's future earnings stream

Jan 1, 1985

By R. A. Sharma, F. D. Richardson

Manganese oxide acitivities and sulfide capacities have been measured at 1650°C in mixtures of MnO + A1203 and MnO + SiO2 - Al2O3. Sulfide capacities have also been measured at 165O0C for melts of MnO + SiO2, MgO + SiO2, MgO + SiO2 + Al2O3, MgO + MnO + SiO2, and SiO2 + Al2O3 and for crystalline CaO. The activity coefficients of the sulfides of manganese and magnesium have been derived where possible. It looks as though the activity coefficients of sulfides are greatest at compositions where the free energies of formation of the silicate mixtures have their maximum negative values. The amphoteric nature of alumina is reflected in the results for the binaries and ternaries in which it is present with silica. The limiting solubility of CaS in CaO at 1650°C is 6.3 x 10-4 mole fraction. THE activities of manganese oxide have been measured in a variety of silicate and aluminate melts by use of the equilibrium (MnO)slag = [Mn]pt .½O2 [l] and the experimental techniques described previously.' Sulfide capacities (CS = wt pct S (PO2/PS2)½) have also been determined in a series of melts, by use of an established method2 which exploits the equilibrium (O°) + ½S2 = (S") . ½O2 [2] If CS and the activity of a metal oxide are known in a melt, the activity coefficient of the metal sulfide can be calculated by use of the equilibrium constant K, for the pure phase reaction MO i ½S2 = MS + ½O2 [3] The activity coefficient of the sulfide is then given by the equation

Jan 1, 1965

By Howard Martens, Pol Duwez

XPERIMENTS were performed on a Cr-Fc alloy Econtaining 44.7 pet Cr in order to determine the heat evolved during the transformation of the a solid solution into the s phase, and the change in volume accompanying the transformation. Since previous measurements on the rate of formation of a from s indicated that the reaction was quite fast as soon as the equilibrium temperature of 820°C was exceeded by some 50°, standard thermal analysis experiments were performed on heating specimens of s at the rate of approximately 40°C per sec. A definite thermal arrest was observed at 870"C, Fig. 1. This result indicates that the reverse seaction of into a is exothermic. From the heating curve of Fig. 1, taking 15°C per sec as the heating rate in the neighborhood of the transformation, 2.4 sec as the time for transformation, and assuming that the specific heat of the alloy at 850°C is an average between iron and chromium, namely 9.5 cal per mol per "C, the latent heat of transformation is approximately 342 cal per mol. The order of magnitude of this latent heat was also obtained by comparing the heating curve of Fig. 1 with a similar curve obtained with pure iron under identical experimental conditions. It was found that the length of the thermal arrest for s was about 1.8 times as long as that for iron. Since the latent heat of the a to 7 iron transformation is 203 cal per mol1, 2 the latent heat of it to a would be 365 cal per mol, which is in relatively good agreement with the value determined from the heating curve. For the determination of volume change, thermal expansion curves were recorded using a specimen containing 44.7 pet Cr and completely transformed to cr by previous treatment. The curves were recorded at a rate of heating of about 4°C per min and at approximately 840°C a sharr, increase in length of about 0.08 pet took place. Fig. 2. It is therefore established that the specific volume of a near the transformation temperature is about 0.24 pet smaller than that of a, and consequently, when the s phase forms in an a matrix, it would tend to shrink away from the matrix. Since the s phase is known to be extremely brittle, these results offer an explanation for the microscopic cracks often observed in the a phase under the microscope. The results of this study are in qualitative agreement with previously published data on stainless steel 19-9DLa and on a Cr-Fe alloy containing 45 pet Cr.' The increase in density due to the transformation from n to s given in ref. 4 is 0.90 pet. These measurements, however, were made at room temperature. whereas the presently reported 0.24 pet is the change at the temperature at which the transformation takes place during heating. In the graph of Fig. 2, the percentage change in length that would be observed at room temperature is given by the length X, which is about 0.27 pet. This would correspond to 0.81 pet in volume change. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-ORD-18 with the Army Ordnance Corps, Washington, D. C. The authors wish to thank this agency for permission to publish the results of this investigation. References I H. Klinkhardt: Measurements of True Specific Heats at High Temperatures. Annalen der Physik (1927) 84, pp. 167-200. - H. Esser and W. Runghardt: Influence of the Method, of Dctcrmination on the Measured Heat Content of Iron. Archtvo ffur Dct Eisenhiittenwesen 11934) 8, pp. 37-38. J. J. Gilman, P. K. Koh, and 0. Zmeskal. Delta Ferrite Formation and its influence on the Formation of Sigma in a Wrought Heat Resisting Steel. Trans. ASM 1 1949) 11, pp. 1371-1388. 1 J. M. Thomas: Discussion of ref. 3. Trans. ASM (1949) 41, pp. 3 390-1392.

Jan 1, 1957

By Charles Pack

Die castings may be defined as metal castings made by forcing molten metal, under pressure, into a metallic mold or die. It is necessary to keep this definition in mind to avoid confusing this process with other permanent-mold casting processes. The fundamental principles of the process have been known and practised many years. The simplest application is embodied in the modern linotype machine in which molten metal (usually tin-lead alloy) is forced under pressure into a metallic mold. The pressure is derived from a piston and cylinder immersed in the molten metal. Progress in the art of die casting may conveniently be divided into three groups: Machine for imparting pressure to the metal, material for the die or mold, casting alloys. The problem of delivering molten metal under pressure into a die is comparatively simple, when dealing with low-fusing-point alloys, as the alloys of lead and tin, but it is much more complicated when dealing with metals of higher fusing points, such as the alloys of zinc, aluminum, and copper. Although the art of die casting is comparatively new and, to a large extent, unknown, the records of the patent office are replete with patents on the subject. Fig. 1 shows the Underwood machine patented in 1902; this is probably one of the first machines designed for the production of commercial die castings. The relation of this machine to the linotype casting machine is clearly apparent. A cylinder and piston are immersed in the molten metal, the application of power to this piston forcing the molten metal, under pressure, into the mold or die. The Doehler machine, Fig. 2, patented in 1907, is based on the same general principles. This machine is used to a large extent at the present time, throughout the United States, for the production of zinc, tin, and lead alloy die castings. In the machine shown in Fig. 3, patented by Doehler in 1910, compressed air is used for forcing the metal into the die. In Fig. 4 is shown another of this type of machine. Here compressed air is applied to the surface of the molten metal to force it into the die. In a machine patented by Chandler in 1914, shown in Fig. 5, the

Jan 1, 1919

By TSUYEE PEI

I FEEL greatly honored and appreciate this opportunity to be able to say a few words about that rather perplexing subject, silver. The constant decline in the price of this metal has now reached the stage where it is of much concern and the cause of serious discussion among the leading financiers, economists, and statesmen of the world. Further- more, it is significant that this subject is so important that almost every day one can read articles pertaining to it in the newspapers and trade publications. Being essentially a banker, and not an economist, I do not claim to be an authority on the silver question. These remarks are merely some of my observations in, regard to the many puzzles which-I came across in my recent studies of this very important question.

Jan 1, 1931

By O. C. Wheeler

In order that the series of reports on oil and gas in Colombia may be complete, the report for the year 1941, which was not available for Volume 160 of the TRANSACTIONS, is given here. The report for 1945 begins on page 4o6.

Jan 1, 1946