Search Documents

By J. C. Swartz

Measurements of the effect of precipitation stresses on the solubility of cementite (Fe3C) precipitates in a iron are reported. Solubilities were determined from measurements of the Snoek relaxation due to interstitial carbon after quenching from various equilibrium treatments. Stress-free precipitates were obtained by a spheroidizing treatment of vacuum-melted Fe 0.06 wt pet C. Subsequent equilibration treatments were designed to suppress nucleation of other precipitates. The results for stress-free cementite give a heat of solution of 14.8 i 0.2 keal per mole and an entropy change of 1.1 i 0.2 eu in the temperature range 400" to 715°C. Comparison with previous data indicates that the heat of solution increases about 6 keal per mole as temperature increases from 700" to 1000°C. Data on self-stressed cementite in quench-aged specimens of Fe 0.013 wt pet C indicate 1) an apparent heat of solution of 12.1 i 0.4 keal per mole in the range 280" to 690°C, 2) a strain energy of- 1.1 keal per mole Fe3C accompanying precipitation at 280°C, and 3') a gradual decrease in the strain energy of precipitation with increasing equilibration temperature. In com-parison with 2 and 3 the strain energy calculated for an isotropic model is 1.7 keal per mole Fe3C. The lower values obtained from the experiment indicated substantial stress velaxation by dislocation motion. WHEN a supersaturated solution of carbon in a iron is aged at temperatures in the range 200o to 700oC, the carbon clusters by interstitial diffusion and forms cementite (Fe3C) precipitate particles. Unstressed cementite has a volume per iron atom 9 pet higher than that of a iron;' hence, cementite precipitate particles are usually under pressure from the iron matrix. The pressure would tend to increase the solubility of cementite in iron.' This report describes anelastic measurements of the solubilities of self-stressed and stress-free cementite in a iron. Previous determinations of the cementite solubility are summarized in Table I. The method of cementite formation for each reference was studied to ascertain the state of stress of the cementite. The results judged to be for stress-free and stressed cementite are distinguished in the table. In the next section an estimate of the stress effect is obtained which is clearly too small to account for the large difference between the previous results in parts A and B of the table. THEORETICAL Let AGO be the standard free-energy change of the reaction Fe3C (eem.) = 3Fe (a) + C (in a) [1] in the absence of stresses. Since cementite precipitates appear to be rather pure10 and the carbon is so dilute in the iron,8 the cementite and iron of Eq. [ I] for the stress-free case have essentially unit activities and the activity of carbon equals its atom fraction xoC Then the stress-free equilibrium is expressed by RT In XoC = -?GO 121 To first approximation the change in the chemical potential of carbon due to the precipitation stresses equals the elastic strain energy W accompanying precipitation of a mole of cementite.2 Hence, in the presence of the precipitation stresses the equilibrium is described by RT In x sq = -?G° + W [3] where xsC is the mole fraction of dissolved carbon in the stressed case. An approximate value of W can be obtained from analysis of the inclusion problem in elasticity theory. The inclusion is a small portion of the matrix phase which has suffered a transformation while still imbedded in the matrix. In the absence of the constraint of the matrix the transformation would be equivalent to a uniform dilational strain eT. Both the matrix (a) phase and inclusion (0) phase are assumed to be homogeneous, isotropic materials. When the a and 0 phases have the same elastic moduli, which is approximately true for iron and cementite,11 the total strain energy per mole ß is12 2µVß(eT)2(3 +4 µx)-I [4]

Jan 1, 1968

By F. H. Deily, Jean M. Quets, Milton E. Wadsworth, John R. 222-000-000-012 Lewis, D. S. Rowley, R. J. Howe

Samples of synthetic magnetite were reduced in hydrogen-water vapor atmospheres in the temperature range 450o to 900oC. The reaction was always surface controlled, indicating the final products of reaction are nonfirotective. Three separate cases have been identified from the kinetic results: Case I, reduction of magnetite to iron below 570°C; Case II, reduction of magnetite to iron above 570°C; and Case 111, reduction of magnetite to wustite above 570 oC. In Cases I and 111 the kinetics have been explained by the formation of oxygen anion vacancies in the magnetite surface followed by associated diffusional processes. In Case 11 the observed kinetics have been related to the concentration of iron cation vacancies in the wustite layer formed, followed by associated steady-state diffusional processes. The concentration of cation vacancies in the wustite is maintained constant by the magnetite-wustite equilibrium. THE reduction of the oxides of iron has been a subject of study and interest for many years. However, few attempts have been made to interpret the results in terms of the mechanism of reduction of an iron oxide by either hydrogen or carbon monoxide. Stalhane and Malmberg' using CO, H2, and CO-Hz mixtures, developed the rate expression: where m = mass of oxide reduced, t = time, k = a constant, s = surface area, P = partial pressure of of CO or H,, and P, = partial pressure of the reducing gas at equilibrium. The rate of reaction per unit area was proportional to the difference between the partial pressure of the reducing gas and its pressure at equilibrium. Hansen, Bitsianes, and Joseph2 studied the reduction of pellets of hematite to magnetite with mixtures of CO-CO,. They concluded that below 450°C the reaction proceeded according to a model in which CO reacts with the hematite surface producing an oxygen ion vacancy. The rate controlling step was then assumed to be oxygen ion diffusion through vacancies resulting in the formation of magnetite. They derived an expression giving the rate of reduction proportional to the cO/CO, ratio. Recently McKewan3 published results for the reduction of magnetite spheres in atmospheres below 570°C. He explained his results by an equation of the form where K, is the equilibrium constant for wustite-iron equilibrium attributed to the formation of wustite as an intermediate in the reduction of magnetite. According to McKewan, Kp is an equilibrium constant for H, -HO adsorption in which oxygen is deposited on the surface from the H,Oand subsequently acts as a poison for reduction by hydrogen. Sample Preparation and Experiments. In this work the authors used the same apparatus and experimental procedure employed in the hydrogen reduction of magnetite. Sintered disk samples weighing approximately 1.5 g and measuring 1.2 cm in diameter and 0.25 cm in thickness were prepared by a method described previously.4 Partial pressures of hydrogen and water vapor were controlled by bubbling hydrogen through a series of flasks containing distilled and deionized water maintained at constant temperature in an oil bath. The total flow rate of the reacting gases—hydrogen and water vapor—was approximately 0.5 liter per min. The entire external system was maintained at a temperature above the oil bath to prevent condensation of water vapor. This was accomplished by wrapping electrical resistance elements over all surfaces. The glass column containing the weighing system-a McBain balance suspended from a gold chain-was enclosed in an aluminum tube heated by nichrome resistance wire enclosed in an insulating material. The temperature of the glass column was held constant by means of a series of thermocouples connected in parallel to a Leeds and Northrup temperature controller. This was necessary since variations in temperature resulted in expansion and contraction of the glass column and could be readily observed with the cathetometer. The spring extensions were measured through a window with a gaertner cathe-

Jan 1, 1962

BUFFALO J R Atkinson, Chairman (Hamilton, Ont, Canada) H R Morlock, Secretary CHICAGO H Erler, Chairman (Gary, Ind ) M E Nickel, Vice-Chairman A M Kroner, Secretary-Treasurer CLEVELAND C W Cravens, Chairman (Cleveland) E J Sobey, Vice-Chairman E Kondas, Secretary Leo Svete, Treasurer DETROIT M Groat, Chairman (Ecorse, Mich ) H W Clark, Secretary

Jan 1, 1957

Executive J V W. REYNDERS, Chairman WILLIAM H. BASSETT E DEGOLYER H C BELLINGER RICHARD PETERS. JR. Finance H. A. GUESS GEORGE OTIS SMITH, Chairman F. JULIUS FONS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A MOSMAN El K MASTERS J. A. SINGMASTIIR Alternates F. G. BREYER C W HAMILTON F. E PIERCE

Jan 1, 1923

By Madan M. Singh, William J. Courtney

Pneumatic stowing is commonly employed in European coal mines, but is not used in the United States. This paper reports a study conducted to analyze the conditions under which pneumatic stowing might be advantageously used and the techniques and costs involved in order to effect this. Although stowing may reduce the subsidence in a mining area, this does not entirely eliminate the surface damage. Besides, the cost of stowing will run about $1.50 to $3 per ton of coal mined not including the cost of fill material, if it has to be bought and transported to the mine. Stowing my, however, be economically viable under special circumstances such as in thick, steep, or contiguous seams.

Jan 1, 1976

By W. N. Lacey, R. H. Olds, B. H. Sage

The volumetric behavior of five mixtures of black oil and natural gas and of two mixtures of condensate and natural gas from a field in the San Joaquin Valley was experimentally established. This work was carried out at roo°, I9o° and 250°F in the pressure interval between 400 and 5000 psi. The viscosity of the liquid phase of four mixtures of black oil and natural gas was experimentally measured in the above-indicated temperature and pressure intervals. The effect of methane upon the precipitation of bitumen from the black oil was studied at 230°F. Introduction The solution of a number of the economical and technological problems which arise in connection with petroleum production is dependent upon the availability of the necessary quantitative information covering the materials involved. This requires data concerning physical properties of naturally occurring hydrocarbon mixtures at the pressures and temperatures characteristic of underground petroleum reservoirs. The experimental determination of the desired data for each situation encountered is relatively time-consuming. However, it is considered to yield results sufficiently more reliable than those obtained from correlations to justify the effort. For these reasons there was undertaken a laboratory investigation of the viscosity of the liquid phase and the volu- metric and phase behavior of mixtures of oil and gas samples obtained from wells in a field located in the San Joaquin Valley. Terminology The nomenclature of petroleum engineering is not at present entirely standardized. Many commonly used technical terms are not everywhere given the same meanings. For the purposes of this paper the following definitions will be adopted: Black oil refers to the dark-colored, hydrocarbon liquid obtained when the producing horizon of the well lies partly in the condensed hydrocarbon phase of the reservoir. Condensate is the term applied to the relatively volatile, pale yellow or amber-colored hydrocarbon liquid that is often obtained from the surface separator system when the producing horizon of the well lies in the gas cap of the reservoir. The gas obtained from the surface separator system is called natural gas regardless of whether the well is producing black oil or condensate. As might be expected from the multi-component character of naturally occurring hydrocarbon materials, the compositions of black oil, condensate and natural gas are subject to considerable variation depending upon the temperatures and pressures prevailing in the surface separator system as well as upon the overall composition of the material produced from the reservoir. In order to obtain samples capable of reproducing the total hydrocarbon material produced by the well, all oil and gas mixtures used in this investigation were com-

Jan 1, 1949

By W. M. Aubrey, P. L. Steffensen

AUTOMATIC grinding control for ball mills in closed circuit with cyclones was developed for the concentrator of the Marmoraton Mining Co., a subsidiary company of Bethlehem Steel Corp. The concentrator, located at Marmora, Ont., Canada, treats an ore that analyzes 35 to 40 pct magnetic iron. Magnetite, the recoverable iron mineral, is concentrated by fine grinding and magnetic separation. The mesh of grind obtained in the plant is not determined by the point at which liberation is sufficient to yield a satisfactory grade of concentrate, but by the physical requirements of the downstream pelletizing operation. This is considerably finer than is metallurgically necessary. The concentrator has two identical units, each consisting of a rod mill in open circuit, followed by a ball mill in closed circuit with a cyclone and two rougher magnetic separators. The cyclone was chosen as a classifier because of its high efficiency on heavy gravity, magnetically flocculated material.

Jan 1, 1957

By O&apos, M. M. Fine, K. G. Meara

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.f In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.' The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In considerbtion of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal orc reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1948

By K. G. Meara, M. M. Fine, O&apos

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.f In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.' The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In considerbtion of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal orc reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1948

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By J. O. Brittain, E. P. Lautenschlager, D. A. Kiewit

Compression tests were run in the temperature range of 700° to 900°C ox 0' phase NiAl intermetal-lic alloys of several grain sizes. At these temperatures the minimum strengths were observed at the stoichiometric composition. While significant increases in strength occurved in both the low-nickel (vacancy) and high-nickel (substitutional) regions, the highest strengths were found in the high-nickel region. During deformation serrated flow was sometimes observed in the low-nickel alloys. After deformation transgranular cvacking and deformation striations were observed in all compositions tested. AS part of a general investigation of the properties of NiAl inter metallic compounds, a preliminary study of the role of point defects upon plasticity was made by high-temperature compression tests on ß' NiAl specimens of several grain sizes and compositions. ß' NiAl is an intermetallic compound having a CsCl structure and a rather wide range of composition from A1-45 at. pct to 60 at. pct Ni.1 According to Bradley and Taylor2 and to cooper,' it possesses a defect lattice in which departures from stoichiometry in the direction of decreased nickel content lead to the presence of vacant nickel sites (although Cooper's work indicates that a small amount of substitution also occurs) whereas departures on the high-nickel side lead to substitution of nickel on aluminum sites. NiAl forms congru-ently from the melt at approximately 1650°C,1 and thus has a higher melting point than either of its component elements. Up to this time, although this and other high-melting intermetallic compounds have been suggested for elevated-temperature usage,4 only the hardness4 and a few tensile-strength measurements5 have been reported for NiAl at high temperatures. In the present investigation the effects of composition upon the compressive-strength properties in a range of 700° to 900°C have been measured for NiAl of several grain sizes. EXPERIMENTAL PROCEDURES The alloys were made as described elsewhere6 from an A1-46.8 at. pct Ni master alloy furnished by the International Nickel Co. with additions of high-purity nickel and aluminum. The charges were vacuum-induction-melted in A12O3 crucibles with small amounts of helium added to the atmosphere to suppress vaporization. They were cooled slowly from the melting temperature to achieve uniform grain size. In order to refine the as-grown grain size a special rolling technique was developed. Alloys were packed into 0.10-in. wall-type 302 stainless-steel tubes which were partially filled with magnesium oxide to prevent bonding between the alloy and the steel jacket. The ends of the tubes were closed by hot forging, and the packets were then hot-rolled. The alloys with greater than 50 at. pct Ni were rolled at 1100°C, but it was found necessary to increase the temperature to 1350° C before alloys with less than 50 at. pct Ni would roll without cracking. With these temperatures, reductions as high as 48 pct were achieved in a single pass. The rolled alloys will hereafter be referred to as "fine grained" whereas the as-grown material will be designated "coarse-grained''. The compression specimens were made by cutting square cross-sectional pieces, approximately 3/16 by 3/16 by 1/2 in., with a water-cooled diamond cut-off wheel from the as-grown or the rolled alloys. Specimens were ground to their final dimensions by polishing through 3/0 grit silicon carbide papers. The final shape was a rectangular parallelepiped of square cross section having a height-to-width ratio of 3:1. Compression testing was carried out in a compression rig of our own design mounted on an In-stron Floor Model. The specimen chamber could be heated to 1000°C and was controlled within ±2°C. The compression rig was enclosed within a bell jar and was maintained at a 50 µ of mercury vacuum throughout the duration of the test. The test cham -ber was heated from room to test temperature within 15 min. Specimens were then held at the test temperature 30 min prior to testing. Previous experiments indicated that no grain growth would occur within this time. An Instron Variable Crosshead speed unit was used to adjust for small variations in specimen lengths in order to have a constant initial strain rate, €, for all specimens of a group. For the fine-grained specimens the strain rate was changed rapidly at constant temperature by a factor of 10 with the speed lever on the Instron. For a given € the compression data was analyzed in terms of true plastic strain (E) and true compressive stress (0).

Jan 1, 1965

By W. C. Ellis, M. E. Fine

In the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;' the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition2 which has a large effect on other properties. The thermal expansion data for the system have been reported only from room temperature to 100 C and for this temperature range a minimum in coefticient in the rcgion of 50 at. pct cobalt is well established.3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the tcrrelation. Experimental Procedure The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 5c pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 1/2 in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for I hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,? the differential expausion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outcr silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested On a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A nonoxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1949

By C. J. Huffman

MAGNESIUM alloy tubing and hollow shapes are finding increasingly wider usage in practical applications today. Square and rectangular tubing and hollow shapes find [ ] greater diversification in use than standard round tubing. Typical applications are roller conveyors, ladder rungs, spools, furniture, tank car loading tubes, athletic equipment, and business machine parts. In general, the amount of tubing and hollow shapes produced represent a minor portion of the magnesium extrusion business. The magnesium alloys in which tubing and hollow shapes are being produced together with typical properties are presented in Table I. MI A alloy is a low cost alloy possessing good welding and stress corrosion characteristics together with moderate formability and corrosion resistance. It is widely used for low strength applications. AZ31 B, alloy is used for moderately stressed applications and possesses good corrosion resistance and formability with fair welding characteristics. AZ61 A alloy has slightly higher physical properties than AZ31 B alloy together with good formabil- [ ] ity and corrosion resistance but slightly poorer welding characteristics. AZ80 A, ZK60 A-F, and ZK60 A-T5 alloys are used where the maximum in physical properties is required. AZ80 A alloy possesses fair corrosion resistance but with formability and welding characteristics inferior to' the other alloys. ZK60 A-F and ZK60 A-T5 alloys, while only recently offered for com¬mercial use, are finding favor due, to the higher permissible extrusion rates. These alloys possess greater toughness than AZ80 A alloy and, while of moderate formability at room temperature, are very formable at 300° to 500°F. The major portion of tubing and hollow shape production at the present time is in AZ3I B alloy. Magnesium alloy tubing is commercially available in the as-extruded condition or, in the case of ZK60 A-T5, in the as-extruded and aged

Jan 1, 1951

By F. T. Davis

Many contributors have added to the fund of knowledge in the basic sciences related to mineral dressing during the past year. During 1964, the French edition of the Proceedings of the VIth International Mineral Processing Congress together with discussions was printed. Also, complete Preprints of papers delivered at the VIIth IMPC were published in September1. Over a third of the papers presented at VIIth IMPC dealt with fundamentals. COMMINUTION It has been postulated by Ponceleta that flaws need not exist before a stress is applied but rather the flaws are created at the tip of a propagating crack at a stress well below the theoretical breaking stress.

Jan 2, 1965

By Alfonso W. Ovalle

INTRODUCTION The block-caving mining method is one of the most economical ways existing today to extract ore from nature. It is undoubtedly the least costly of the underground systems and moreover it compares favorably to open-pit mining. In addition to its low cost characteristic, the block-caving mining method permits a great extraction volume as can be exemplified by El Teniente's output capacity of over 22 million tons of ore per year. These characteristics of block-caving give assurance that, even though it is a very old mining system, it will be a good answer to the many future large massive low ore grade deposits to come and a1 so to rep1 ace open-pi t mining as such operations get deeper with higher stripping ratios. These are the reasons that induce further study of block-caving. In this paper block-caving at El Teniente is analyzed with due consideration to the major problems that this mine will encounter. Emphasis is given to the factors influencing the mining of soft ore which accounts for most of the ore to be extracted in the next ten years. A separate paper is devoted to a major modification introduced to block-caving hard primary ore at El Teniente by means of LHD equipment extraction. DESCRIPTION OF THE PRESENT MINING Ore Production and Flow Over 62.000 tons per day of ore are extracted 359 days per year at the El Teniente Mine. The Teniente 8 train haulage level at 1.983 m takes 29.000 tons daily to the Col6n Concentrator. Two trains make the 8 km haul with 16 cars per train. Car capacity is 90 tons. The Teniente 5 train haulage level 298 m above takes 33.000 t per day to the old Sewell Concentrator. Ore is produced from three production areas in two different levels. The so called North Mine produces 42.000 tons daily from the Teniente 4 level 65 m above the Teniente 5 haulage level. The Central Mine produces 1.000 tons from the first hard rock block caved at the Te- niente 4 level. The combined 43.000 tons per day production is sent through inclined 2 m dia- meter raises to the Teniente 5 haul age level , where 33.000 tons are taken 2.5 km to the Sewell Concentrator and 9.000 tons are hauled 0.5 km to a 5 m diameter vertical ore pass which sends ore to Teniente 8. The haulage is by 7 trains, 15 gabble-bottom cars per train. Car capacity is 20 tons. The so called South Mine produces 19.000 tons per day from the Teniente 1 level 645 m above the Teniente 8 haulage level. Ore is transferred by 2 m diameter inclined raises to the Ten 1 Retram level 22 m below, where 5 trains with 20 Sandfor Day cars per train, 8 tons capacity per car, haul the ore 1.5 km to two vertical 5 m diameter ore passes which connect to Ten 8. Starting in 1982 the Central Mine will in- crease production to 6.000 tons per day. An in- dependent loop haulage system will start operat- ing at the Teniente 5 level to feed a new under- ground 1.372 mm (54 in.) gyratory crusher which will send minus 152 mm ore (9 in.) to Teniente 8. In two or three years time the North Mine will only feed the 33.000 tons to the Sewel 1 Concentrator with its old Teniente 5 haulage system. The Col6n Concentrator will be fed from the Central and South Mines. Figure 1 shows the transfer systems and ore flows. The Ore Body In plan view at the Teniente 4 level the ore body has a kidney shape 1.800 m long and between 400 to 700 m wide. The north-eastern section of the ore body was washed away by the Teniente River. At the Sub 5 Level, 125 m below Teniente 4, the mineralization completely surrounds the circular 1.000 m diameter steep-sided barren breccia pipe (Braden pipe) . The ore body rock is 73% andesite, 14% diori te, 13% dacite and 6% mineralized breccia. Most of this ore is secondary enrichment sulfides which apart from the dacite is strongly fractured being chal cocite, cove1ine , bornite and

Jan 1, 1981

By W. S. McCain, B. A. Wilcox, A. H. Clauer

The creep and creep-fracture behavior of a Ni-200-2Th0, alloy has been studied over the temperature range 816° to 1038°C and stress range 4000 to 19,000 psi Specimens having their axes either parallel or transverse to the final sheet-rolling direction were tested in air, and the apparent activation energy for creep was found to be 92 kcal per mole, regardless of specinien orientation. The stress dependence 01- the steady-state creep rate, was satisfied by where n depended on orientation; n = 9.7 for rrzaterial transverse to the rolling direction and n = 24.3 for material parallel to the rolling direction. In the latter case, the relation was also valid. The rupture strength of material parallel to the rolling direction was -1.5 times gveater than the transverse rupture strength. Several tests in vacuum revealed that here the creep rate was higher and rupture life lower than for comparable tests in air. THERE is an increased interest today in producing improved dispersion-hardened alloys for high-temperature structural applications. This had led various materials designers to modify existing alloys, such as thoriated nickel. One system that has received considerable attention is based on chromium additions to Ni-ThO2, with the obvious motive of improving the oxidation resistance. Another effect of chromium is that of lowering the stacking-fault energy, y, of nickel. For example, the addition of 30 wt pct Cr decreases y from -225 erg per sq cm for pure nickel1 to -70 erg per sq cm.' This decrease in y could have several effects on the deformation behavior. There is some evidence that cross slip of dislocations around Tho2 particles is a mechanism of tensile3 and creep4 deformation in TD Nickel (Ni + 2 vol pct ThO2) at temperatures below 0.5 the absolute melting point of nickel, T,. A decrease in ? by chromium additions should increase the difficulty of cross slip. Also it has been suggested that the high-temperature (T > 0.5Tm) rate-controlling creep process in "recrystallized" Ni-Tho2 alloys is the climb of edge dislocations over Tho2 particles.5 According to weertman6 a decrease in the stacking-fault energy should decrease the dislocation climb velocity resulting in a decreased steady-state creep rate. Thus, chromium additions to recrystallized Ni-Tho2 alloys would be expected to decrease the creep rate, all other conditions being constant. However, a difficulty arises when the stacking-fault concept is applied to high-temperature creep of dispersion-strengthened metals which are produced on a commercial or semicommercial scale. This occurs because the materials are processed so that they have a high-stored energy of cold work, and the other substructural effects could obscure any influence of stacking-fault energy per se. An example of an alloy with a high stored energy of cold work is TD Nickel bar. This material has a fibrous grain structure (1 I diam by 10 to 15 p long), and the structure is stabilized by the ThO2 particles. Annealing at high temperatures, e.g., 3 hr at 1300°C, causes no recrystallization or grain growth.4 Previous work by the authors4 showed that the high -temperature creep behavior of TD Nickel could not be related to any simple dislocation theory of creep, and this probably was associated with the complex initial structure of the material.

Jan 1, 1968

By Fred W. Gordon

It is my purpose to call attention to the close approximate correctness of certain coefficients and formulas concerning the flow of gases, and their applicability to the practical construction of flues and

Jan 1, 1886

By L. Delisle

This work represents the first step of an attempt to test the applicability of the electron microscope to the study of subgrain structures in copper. Observations on annealed and deformed single crystals and polycrystalline samples of copper are described. IN the course of study of the structure of fine tungsten wires and tungsten rods with the electron microscope, well defined subgrain structures were observed. The size, size distribution, and orientation uniformity of the etch figures varied widely in different samples. Figs. 1 and 2, electron micrographs of a tungsten wire and of a tungsten rod, respectively, are illustrations of the difference in size and size distribution of the etch figures in different samples of the same metal. The observed differences, as pointed out in a previous paper,' appeared to be related to the heat and mechanical treatments of the samples. They were also consistent with the results reported in the literature on the mosaic structure of metals.' For that reason a program of research was initiated in an effort to obtain more systematic evidence of the possible relation of heat and mechanical treatments to the subgrain structure of metals as observed in the electron microscope. The purpose of this paper is to present observations made on the effect of cold work on the subgrain structure of copper. Procedure Starting Materials: Copper was the metal studied because it can be obtained in a high degree of purity, much information is available in the literature on its properties and its response to cold work and heat treatment, it shows no allotropic change, and it is sufficiently hard to be handled without great difficulty. Two groups of specimens were used: 1—single crystals cast from spectroscopically pure copper and 2—polycrystalline samples of oxygen-free high conductivity copper. Single crystals were studied because it was hoped that the elimination of a number of variables, such as grain boundaries, orientation differences, degree of purity, would simplify the problem and perhaps permit a better understanding of the phenomena that would be observed. The polycrystalline samples were designed to give a general picture of the changes considered. The single crystals were made of copper which analyzed spectroscopically to better than 99.999 pct Cu. They were cast in vacuum, by the Bridgman method, in crucibles made of graphite with a maximum ash content of 0.06 pct. The mold design is shown in Fig. 3. It permitted casting crystals of the size and shape required for the experiments, so that the danger of introducing cold work in the original samples by cutting or other machining would be eliminated. The polycrystalline samples were pieces, 3/4 in. long, cut from a rod of oxygen-free high conductivity copper, % in. in diameter. A flat surface, 1/4 in. wide, was milled along the rods, polished, and etched. The samples were then annealed in vacuum at 850°C for 1 hr. Polishing and Etching: Work previously done on tungsten,' polished mechanically and etched chemically," had shown that: 1—the general appearance of the etch figures of a given sample was not altered by repeated polishings and etchings under similar conditions; 2—variations in the time of etching and the concentration of the etchant changed the definition of the etch figures, but did not alter their general size nor orientation distribution within the limits of observation. Further work confirmed the reproducibility of the subgrain structures observed in, 1—single crystals and polycrystalline samples of copper when polishing and etching were repeated under similar conditions, and 2—specimens of tungsten and polycrystalline copper when electrolytic polishing and etching were substituted for mechanical polishing and chemical etching, respectively. On the strength of these observations, it was felt that, if conditions of polishing and etching were kept constant, changes observed in the subgrain structure of a sample upon deformation and annealing would be attributable to such treatments. For that reason the conditions of polishing and etching were kept as constant as possible. The single crystals were polished electrolytically in a bath of orthophosphoric acid in water, in the ratio of 1000 g of acid of density 1.75 g per cc to 1000 cc of solution, under a potential drop of 1.6 to 1.8 V. Electrolytic polishing was selected to prevent the formation of distorted metal in polishing. The same samples were etched by immersion in a 10 pct aque-

Jan 1, 1954

By E. W. Newman

During 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for ' military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mind during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River: and Absarokee, on the Still water River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specificstions as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. History of Deposits The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the fist optical calcite produced from Montana came from the Cartwright deposit near Grey-cliff,' but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by .4. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the

Jan 1, 1948