Search Documents

By L. H. Schwartz, S. K. Lahiri, M. E. Fine, D. Chandra

WHILE the yield stress of solution treated Fe-Cu alloys increases rapidly with aging, a precipitate has only been directly observed in overaged samples.'-" This precipitate is essentially pure fcc copper, the E phase. Hornbogen2 suggested that the initial hardening is due to clustering of copper atoms in a bcc iron matrix. Hornbogen was not able to obtain direct confirmation for such bcc clusters by either X-ray diffraction or electron microscopy; however, he did observe analogous clustering in Fe-Au alloys7 where the scattering factor difference between iron and gold is more favorable than that for iron and copper. Fujii, Nemoto, Suto, and Monma4 recently observed diffuse electron diffraction scattering in a 2.5 pct Cu alloy aged at 500°C: for 30 hr. They suggested that part of the diffuse SCattering was due to a modulated structure of 26 to 42 wavelength parallel to the (110) matrix plane. This disappeared with further aging. However, 30 hr at 500°C is well beyond the peak strengthening in this alloy which occurred at less than I hr at 500oc.4 By transmission electron microscopy they could not distinguish between quenched samples and samples aged to maximum strength. The purpose of the present investigation was to try to obtain further confirming evidence for a precipitation stage preceding the formation of the fcc E phase. Change in Young's modulus was selected for study be- EXPERIMENTAL PROCEDURE The Fe-1.67 at. pct Cu alloy was supplied by the U.S. Steel Corporation in the form of a hot forged rectangular bar. The carbon and nitrogen contents of this alloy were 70 ppm and less than 10 ppm, respectively. The samples for Young's modulus measurements were made by cold swaging to & in. diam and cutting to 2 in. lengths. Tensile test samples 1 in. long were prepared by cold rolling to a thickness of 0.012 in. and then machining to gage dimensions of 0.5 by 0.012 in. For Mijssbauer studies, foils 1 mil thick were prepared by cold rolling. During fabrication the alloy was given intermediate anneals at 845OC followed by quenching. The specimens after preparation were solution treated at 1000°C (y field) or 845°C (a field) for 1 to 2 and 5 to 6 hr, respectively, in a dynamic vacuum of about 2 x lom6 torr. The tensile and modulus specimens were drop-quenched into iced brine through an aluminum foil which vacuum-sealed the bottom of the furnace tube. The MOssbauer foils were drop-quenched into helium gas cooled by passing through N2 (liq) in a copper coil. The grain diameter of the modulus and tensile specimens was between 0.025 and 0.035 mm. The samples were aged from 400" to 500°C in a dynamic vacuum of 2 x 10-6 torr and cooled by pulling into a water-cooled portion of the vacuum system. The dynamic Young's modulus was measured at room temperature using electrostatic excitation and detection of longitudinal vibrations.' Neglecting any length change during the aging, (this is expected to be comparatively small), the fractional change of Young's modulus (?Et)/Eav, is equal to twice the fractional change of the resonant frequency (?ft)/fav . ?ft =ft —fo where fo and ft are the resonant frequencies of a specimen before aging and after aging to time t. The measured f's, approximately 51,000 cps, were corrected to 25°C for any variation in the ambient temperature. The tensile tests reported were carried out at room temperature in an Instron with a 1000 lb full scale load cell. The flow stress reported herein corresponds to a strain of 0.002. The Massbauer spectra were taken in a constant acceleration model AM-1 NSEC spectrometer. The

Jan 1, 1970

By Ralph W. Smith

DEVELOPMENT of the lime industry- in Ste. Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there are today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. GEOLOGY The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft. of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaC03; 0.35 Si02; 0.3 R203; 0.35 MgCO3; 0.3 S03. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 ½ º. Thus the outcrops of the various sedimentaries run approximately north and south. A line running west from Ste. Genevieve crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 ½ º the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile

Jan 1, 1938

By Frances Hurd

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200' C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating.

Jan 1, 1927

Jan 1, 1916

By A. W. Hesse

The trend of American construction toward permanence and longevity is noticeable in the more recent coal plant installations; also, the policy of many coal operators has changed from seeking to obtain the desired tonnage from several plants of small capacities to designing a single installation to produce the whole amount. The mine openings and plant of the Nemacolin mine of The Buckeye Coal Co., are located on the Greene County side of the Monongahela River, 73 miles south of Pittsburgh. The map (Fig. 1) shows the general location, also the Lambert syncline. This syncline partly accounts for the selection of the site; the other reasons were the possibilities of rail and river shipments. Two shafts and a slope were sunk to the coal, work starting on all three in the second half of the year 1917. The air shaft was sunk to a depth of 243 ft. and completed in February, 1918; the slope was completed in November, and the skip shaft was stopped at a depth of 21 ft. below the coal, then the concrete lining was stopped 8 ft. above the coal August, 1918. Work on the skip shaft was resumed May, 1923, and sunk to a depth of 60 ft. below the coal by September, but it was not until May, 1924, that the lining was poured. Max. Min. WateR Water during after Sinking, Crouting, Depth or Cu. Yd. Cu. YD. Gal. per GaL. per Opening Size Length Excav. Conc. Min. Min. Air shaft..... 20 ft. diam. 251 ft. 8 in. 4788 1902 475 2 Slope........ 11 it. by 19 it. 1 in. 857 ft. 11500 5200 50 2 Skip shaft.... 32 ft. 8 in. by 12 it. 8 in. 296 ft. 6042 2293 300 3 Fig. 2 shows sections of these openings. The surface plan shows the relative positions of the openings. Coal was first hoisted from the air shaft May 7, 1918, and entry driving was continued; but the coal had to be stored, as the railroad had not been extended from Crucible to Nemacolin. As soon as the slope was driven to the coal and the linings concreted, the entries were driven along projected lines to connect with those advancing from the air shaft, and skip shaft. As soon as the underground connections had been made between the two shafts, the hoisting by buckets was inaugurated at the skip shaft and construction on the fan at the air shaft started.

Jan 1, 1927

By Earl Bardwell

THE determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. THE EFFECT OF ANNEALING TEMPERATURE ON PHYSICAL PROPERTIES For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows:

Jan 8, 1914

By R. D. Begley, A. W. Khair

Introduction The technique being investigated here uses a physical mine model which consists of a plexiglass room-and-pillar model 11.4 x 11.4 cm (4.5 x 4.5 in.). It is placed at the bottom of a larger plexiglass box 25.4 x 30.5cm (10 x 12 in.). The box is then filled with a model material representing geologic overburden. Sand has been selected because of its deformability under gravitational forces. The mine model is capable of creating a cavity and induces movement on the surface of the model material. This surface disturbance can be measured using a photographic technique called holographic interferometry. This paper discusses results of an investigation of the possibility of generating subsidence criteria using physical mine models and laser holographic interferometry. Problem Statement Subsidence appears to be widespread in two states - Pennsylvania and Illinois - although serious subsidence is found in localized areas of numerous other states (HRB Singer Inc., 1977). The US Bureau of Mines estimates that more than 1618 km2 (400,000 acres) of urban areas are threatened by subsidence. Pennsylvania and West Virginia contain 57% of these threatened areas, with the remainder being spread out over 16 states (Johnson and Miller, 1979). Events of subsidence have been reported in urban areas, including Pennsylvania (Gray et al., 1977) and Illinois (Mahar and Marino, 1981). One location has observed three episodes of subsidence beginning in 1950 (Bruhn et al., 1981). These subsidence events all occurred over abandoned room-and-pillar mines. Some mines have been abandoned more than 50 years (Bauer and Hunt,1981) . Available research does not offer much on the problem related to time dependent subsidence, especially those associated with the failure of remnant coal pillars. The physical modeling technique developed at West Virginia University is capable of measuring both instantaneous and time delayed subsidence. Laser Holographic Interferometry Laser holographic interferometry, or holometry, uses the interference properties of laser light to measure small movements of objects. The object requires only optical access and no surface instrumentation. This technique is closely related to photoelasticity. Both techniques rely on the uniqueness of the light reflected off or through an object in any given state of stress. The entire measurement process is done remotely without any surface instrumentation and without using a camera. The interferogram is constructed and visual observation will yield fringes on all areas that yielded or moved. The displacement represented by one fringe was determined by Wilson et al. (1977) and is given by the relationship: [d ='1(1) 2 cos 8 where d = displacement of one fringe 6 = incident angle of laser light A = wavelength of light (632.8 x 10-9 meters for Helium-Neon lasers)] In summary, holometry is capable of detecting very small movements of objects under study. It is a very sensitive process that requires laser light and vibration free experiments. Experimental Program Lab Facilities The primary components of the facilities were the laser and the optical table. The light source was 50 milli-watt, Helium-Neon laser. The optical table was a granite slab weighing nearly one ton. All experiments were performed on the optical table. It consists of a large table sitting on air cells similar to car innertubes. Six air cells were placed on top of two layers of wood and Styrofoam. Figure 1 is a schematic diagram of the vibration free table. Even with these precautions, the experiments still had to be performed at night to reduce potential traffic related vibrations. Room-and-pillar mine models consisting of three different pillar sizes were constructed out of plexiglass. The models were designed to represent three different extraction ratios. Figure 2 shows the models. The extraction ratios were determined by the tributary loading concept (Peng, 1978). These models were the primary component of a seam extraction simulator. A schematic of this simulation device is shown in Fig. 3.

Jan 1, 1986

By H. J. Rose

Sixty-five million net tons of coal were carbonized in the by-product and beehive coke ovens1 of the United States during 1924. This tonnage represented 13.4 per cent. of the bituminous coal which was mined in that year. Table 1 shows production and disposition.2 Table 1.—Production and Disposition of Ocen Coke in 1924 By-product Beehive Total Coal charged into ovens, tons................ 49,061,339 15,914,310 64,975,649 Coke produced (exclusive of screenings and breeze), tons............................. 33,983,568 10,286,037 44,269,605 Average yield of coke, per cent ............. 69.3 6.46 68.9 Disposition of coke, per cent.: Blast furnace.......................... . . 82.6 Foundry............................... . 13.3 6.6 Domestic.............................. . 1.4 6.7 Water gas manufacture and all other uses.. 4.6 . 4.1 Cokes having somewhat different combinations of chemical and physical properties are desired for the various uses listed above, and these properties depend primarily upon the types of coal used. American coals have a wide range of purity and coking quality, and the chief subject of this paper will be the selection of coals for the manufacture of blast furnace, foundry, domestic, and water-gas coke, in by-product coke ovens. It will obviously be necessary to include a discussion of those physical and chemical characteristics that are generally considered essential or desirable for each type of coke. Suitable Coals The examination and development of new sources of coking coal are important because of the irregular and limited distribution of high-grade

Jan 1, 1927

By L. A. Norman

ANOTHER chapter in the history of Mother Lode mining is being written by operations in the Old Eureka mine near Sutter Creek, Amador County, California. During a two-year period (1938-1939), 85,517 tons of ore averaging 0.62 oz. gold per ton were mined and milled, as compared to the production of approximately 210,000 tons of 0.315-oz. gold ore during the preceding seven years. This is a repetition of mining history in the Mother Lode, where a period of prosperity has followed a long period of lean production. The location of this new ore in the hitherto unproductive hanging-wall greenstones and its mining and geological developments are most interesting. HISTORY OF THE OLD EUREKA MINE The Old Eureka mine, also known as the Hayward, Eureka, Hetty Green and Amador Consolidated, is in the most productive 10-mile length of the 120-mile long Mother Lode of California. The mine was first opened in 1852 with operations more or less continuous for the next 30 years. Production during this period amounted to $12,000,000 from an ore shoot 500 ft. long, which bottomed 1700 ft. below the surface. The shaft was continued as a prospect to 2065 ft. on the incline, where work was stopped in 1881. The mine was sold in 1916 by Hetty Green and the shaft deepened to the 3500-ft. level (3212 ft. vertically) by the new owners. Drifts were run on the 1700, 2100, 3000 and 3500-ft. levels, together with approximately 1500 ft. of crosscuts. No ore was found and work was abandoned in 1921. The present owners, the Central Eureka Mining Co., purchased the mine in 1924 after threatened litigation over rights to the rich ore shoot being mined from the lower levels of the Central Eureka mine on the south. Rehabilitation of the shaft commenced in 1926 and in 1930 mining on the old 2100-ft. level was started. While efforts of the previous owners had been directed for the most part toward the area south of the Old Eureka shaft and adjacent to the productive Central Eureka mine, the present owners started drifting northward on the old 2100-ft. level. On the 2000-ft., 2100 and 2300-ft. levels, drifts were run in part along the

Jan 1, 1939

By J. H. Nead, T. S. Washburn

The grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure— killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes arc not present. Also, the rimmed ingot has no well defined pipe, as compared to the deep pipe on the killed ingots, and there are numerous primary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differentiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7—as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined [or deep as in the killed ingot of Fig. 1. In killed ingots, primary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

By T. S. Blair

I feel a certain sense of responsibility in bringing before you the subject of the direct process in iron manufacture. I am aware that, in such a body as I have now the honor of addressing, there are few who are not already so well informed upon its past history that it would be a weariness to them to listen to anything else than an account of practical success. Yet, to claim that success involves so much that, if I do not make good my claim, I deservedly expose myself to severe criticism. The whole literature of the art, so far as it relates to the direct process, is, up to this time, but a history of failure. It is safe to say that more money, time, and talent have been fruitlessly spent in the pursuit of this object than in all the other unsuccessful efforts in the whole line of iron metallurgy. A distinguished authority in patent law has remarked that " the invention records of the United States and of foreign countries are filled with the waifs and abandoned relics of these abortive struggles." Dr. Percy, whose great work may be taken as an epitome of all that was worth mention, whether useful or curious, in pig-iron metallurgy, up to the date of its publication (1864), after giving elaborate accounts of various attempts at the direct process, condenses his own opinion of all that had been then effected, into a brief but summary comment upon a pamphlet of one of the sanguine inventors who had said: "It is evident that the present mode of working iron

[ ]

Jan 1, 1946

By R. M. Howe, J. Spotts McDowell

Preparation and Use.—Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for bricklaying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining the crude or lightly burned mineral at a temperaturc that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and CO2; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brickmaking in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1/2 to 1 in: (1.25 to 2.5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are Glled. At most plants such holes, at the end of each week, are also carefully filled with dead-burned grain magnesite. For temporary

Jan 1, 1920

By Jose Luis de Valle Alonso

Although present electrolytic zinc manufacturing processes are aimed at the direct wet process recovery of the metal, and, with this end in view, several industrial scale patents have been applied for during the last few years, the object of this paper is to enhance the possible metallurgical interest in the conventional recovery of zinc and other metals from leaching residues. Therefore, its main end is the description and discussion of the recovery process of zinc, lead and cadmium from leaching residues. Fundamentally, the process consists of the following: Flotation processing to recover the non-roasted blende still contained in the residues. Pyrometallurgical processing of flotation tails in low-shaft furnaces (kilns) and open-flame rotating furnaces and the ensuing recovery of zinc, lead and cadmium as a mixture of their oxides through volatilization.

Jan 1, 1970

By R. F. Mehl, C. S. Barrett, A. G. Guy

INTRODUCTION IN the last few years this laboratory has published a series of papers on the mecha¬nism of age -hardening.14,1,6,11,20 Briefly stated it has been proposed that hardening is caused by lattice strains created by lat¬tice coherency between matrix and precipi¬tate; much experimental evidence has been advanced to support this thesis. The system Cu-Be is an attractive one to study. It is a system that exhibits marked age hardening; it ought to be subject to the type of analysis of structural changes hitherto explored and it is a prominent example of "discontinuous precipitation," which, though studied in other cases, 6,20 remains largely unexplained. This research shows that hardening in the Cu-Be system proceeds essentially as proposed earlier.14 Guinier-Preston zones have been observed to form on the {100) planes of the matrix; no transition lattice was found. Aging and overaging were ob¬served to occur most rapidly in the region of discontinuous precipitation-the grain boundary-apparently accelerated there by strain. The Constitution of the Cu-Be System The Cu-Be constitution diagram is shown in Fig I. The structure of the ? phase was determined by Misch16 as of the caesium-chloride type with a lattice con¬stant of 2.598 Å High temperature X ray photograms of 7.2 pct Be alloy made by Kossolapow and Trapesnikow13 led them to conclude that the structure of the P phase is simply disordered body-centered cubic with [ao] = 2.79 Å at 750°C. Previous Work The initial work on the age-hardening of Cu-Be alloys was that of Masing, Dahl, Holm, and Haase. Their numerous papers were published in book form in 1929, sub¬sequently translated.18 The effects of Be content, solution temperature, aging tem¬perature, and cold work on the hardness developed in these alloys were studied. An initial decrease in the electrical conduc¬tivity was observed when strips of a 2.5 pct Be alloy were aged at temperatures from 200 to 350°C; a wire of the same analysis failed to exhibit this decrease when aged at 350°C. A volume decrease of 0.6 pct oc¬curred during aging at 250°C. Microscopic investigations of quenched and aged alloys disclosed a regularly ori¬ented "striping" (ripples) on the a and on the ß grains. In the case of the ß the cause of the striping was held to be decomposition

Jan 1, 1948

By E. von Maltitz

IN his highly interesting paper on "Piping and Segregation in Steel Ingots,"1 Prof. Howe emphasizes the effect of successive phases of internal pressure in the ingot in the evolution of gas, and the consequent formation of blow-holes. From his statements in other places, it may be inferred that he does not here intend to ignore the other variable factor, temperature, but rather to discuss this one more particularly. At all events, it is my purpose not to engage in controversy with Prof. Howe, but rather to contribute, towards the complete elucidation of this important subject which we all desire, my own views and experience. If, in doing so, I specially emphasize other factors than pressure, I need not be understood as denying what I do not think it necessary to discuss fully. Nor, in presenting my own original conclusions, need I be understood as claiming to be the first who ever reached or announced them. Many things are asserted or suggested upon inconclusive evidence; and to confirm such tentative propositions may be as valuable a service as to overthrow them. In the following passage, Prof. Howe adduces analogies, based upon the behavior of charcoal and of water, respectively, which seem to me questionable "In general, the. solvent power falls as the pressure falls ; and in general it rises as the temperature falls. Thus, to heat a solid, for instance charcoal, may expel part of its dissolved gas ; and a tumbler of water drawn cold from the faucet gradually evolves gas, as it stands and warms up on the sideboard." (p. 238.) Charcoal is a solid body, which has the property not only of absorbing gases in large quantities, but also of expelling the thus absorbed gases upon heating. A comparison between charcoal and iron as to the absorption of gases is scientifically not possible ; the gas-content of charcoal is partly due to the

Sep 1, 1907

IN THE past, we have, perhaps, been somewhat careless in our furnace practice, in the use of high-grade material, lowering the production costs through demanding high-grade ores, increasing the size of units, and eliminating heat losses by collecting and returning unused heat to our furnaces. Further economies would seem to be possible through keeping out of the furnace those materials that appear to serve no useful purpose and carry with them heat that should be used in reduction operations. In the manufacture of pig iron, about three tons of inert nitrogen pass through the furnace for each ton of iron produced. This nitrogen serves no useful purpose in the chemical actions involved, but when discharged into the atmosphere it carries away a considerable quantity of heat. Can not this loss be eliminated, at least in part, through the use of more oxygen in the blast? Many metallurgical chemists, during the past 20 years, have stated that they thought it can and have urged that the plan be tried. Others have expressed doubt, not being able to visualize how more oxygen could be used in present practice; they have regarded it as impracticable, without trying to conceive of an entirely new practice based on a new reagent. That more experimental work has not been done is due to the fact that no cheap oxygen has been available, but the committee believes that there is strong reason to expect that, should a demand exist, 99 per cent. oxygen may be made at a cost not to exceed $3 per ton. The theoretical studies of the committee have indicated such marked economy by using oxygenated air in various operations that its members strongly recommend experimental work to verify the anticipated economies. The committee has developed plans for experimentally determining the effects of oxygen-enriched air on the operation of an iron, blast furnace. A furnace with a height of 30 ft. has been built and it is recommended that the plans be put in, effect as the first step in the research.

Jan 11, 1924

By Carl Swartz

METALLURGISTS differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a one-millimeter screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in, color, having the general characteristics of a spinet Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution zinc values tied up in this compound remain behind. HISTORY In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite, others merely a mixture of zinc and iron compounds.

Jan 1, 1927

By A Andersen

DURING an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investiga-tion was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this sys-tem as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. S. Smith's latest work on the copper-silicon system8 was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essen-tial features, except the temperature of the peritectic line above 830° C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centered cubic with a lattice constant of 2.848 A.. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexag-onal phase, and to avoid confusion this designation will be adhered to in the present paper.

Jan 1, 1939

By Arthur West

It is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 ions capacity each. In this, as in all the other stations described in this paper, each furnace is blown by two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines. The next station built is shown in Fig. 2. This is the plant of the Minnesota Steel Co. at Duluth, Minn., and is at present constructed for five engines, to handle two furnaces, with one spare engine. The engines are of practically the same size as those at Bethlehem. Instead of being arranged in right-hand and left-hand pairs, as at Bethlehem, all the engines are of the same hand; this arrangement has some ad-

Jan 1, 1915