Search Documents

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the low funding level program plan.

Jan 1, 1980

By Larry Joe Linley

The Department of the Interior, Bureau of Mines is reviewing explosion protection methods for use in gassy coal mines. This performance criteria guideline is an evaluation of three explosion protection methods of machines electrically powered with voltages up to 15 000 volts AC. A sufficient amount of basic research has been accomplished to verify that the explosion-proof and pressurized enclosure methods can provide adequate explosion protection with the present state of the art up to 15 000 volts AC. The routine application of the potted enclosure as a stand alone protection method requires further investigation or development in order to clarify performance criteria and verification-certification requirements. An extensive literature search, a series of high voltage tests, and a design evaluation of the three explosion protection methods performed at White Sands Test Facility indicates that the explosion-proof, pressurized, and potted enclosures can all be used to enclose up to 15 000 volts AC, if the performance criteria and verification-certification requirements recommended in this guideline are implemented.

Jan 1, 1982

By P. Scinto, A. Festa

"Orway Mineral Consultants Ltd (OMC) as a consultancy has specialized in comminution circuit design for over 30 years. The OMC Power Model is OMC’s in-house software for specific grinding energy power-based circuit calculations. The model uses ore hardness parameters from testwork, circuit configuration, equipment geometry and operating conditions as inputs. The model combines proprietary and published power models to predict the total specific energy and the specific energy for each of the components of the comminution circuit. This makes the software a valuable tool for the design and validation of JKSimMet modelling or actual plant performance. Proprietary calculations have been developed and reconciled with over 100 plant benchmark projects encompassing a variety of comminution circuit configurations.This paper describes the OMC approach for determining power requirements for the design of grinding circuits. The accuracy of the OMC Power Model software is confirmed through plant survey benchmark performance and comparisons are made with other power modelling techniques. Practical examples are presented, showing applications for single stage SAG (SS-SAG), SAB and SABC circuit configurations.IntroductionConventional low throughput grinding options, consisting of multi-stage crushing followed by rod and ball mills, have almost become obsolete in the move to higher milling rates required to process lower metal grades. Grinding circuits with fully autogenous (AG) or semi-autogenous (SAG) mills, often combined with ball mills are now the standard to meet the high capacity requirement for processing ores with lower metal grades. Simulation software and power-based equation methodologies have been established for designing AG/SAG based grinding circuits and predicting their energy requirements.Presently, power-based equations remain the principal method for designers to size mills and estimate the power requirement for comminution circuits. The technique is simple and it relies on the design to specify a feed and product size plus a hardness index to produce a specific energy value (kWh/t). The desired throughput of the mill is multiplied by the specific energy to give the mill power requirement, which is used in turn to size a mill for dimensions, internal geometry and loading conditions to match the power draw."

Jan 1, 2015

By Shaw-Shong Liew

This paper presents the processes of investigation, analysis, design, construction and monitoring of soil nail stabilisation work to facilitate a 14.5 m deep excavation at an uncontrolled fill ground. An extensive instrumentation programme had been implemented to monitor the performance of the stabilisation solution, to provide validation for the designed nail resistance and groundwater variation. From the monitoring results, it was proved that the soil nail stabilisation technique is effective for loose saturated fill provided that substantial care is taken during implementation. Construction difficulties, solutions to overcome the problems and lessons learned will be discussed in the paper.

Jan 1, 2006

By John Corcoran

INTRODUCTION Content of this Report The 1300m long twin-bore 8.1m diameter Airside Road Tunnels (ART) were excavated beneath the busy taxiways and stands of Heathrow Airport between 2002and 2003. The tunnels were fully completed and handed over to the client for use early in 2005. This paper will describe the purpose of the tunnels, and the measures put in place to minimize the impact of construction on the daily activities involved in running an international airport. Terminal 5 Construction Heathrow Airport is the busiest international airport in the World, with a current capacity of circa 67 million passengers per year, based on existing infrastructure of4 passenger terminals, 1 cargo terminal, 2 runways and 170 aircraft stands. Terminal 5(T5) is being built to increase Heathrow’s passenger capacity by providing the following: 12 additional aircraft stands through redevelopment of the south apron area, in the autumn of 2004 A main terminal building (T5A) and a first satellite (T5B), and 43 additional stands by the spring of 2008, most of which will be able to receive the new generation large aircraft (Airbus A380) A second optional satellite (T5C) by year 2010 A third optional satellite (T5D) by year 2015 The total value of the project is approximately 4.2 billion pounds for the main phase of the works spanning from 2000 to 2007. Purpose of the Airside Road Tunnel The ART has been constructed to support the internal road traffic of the airport between terminals, aircraft stands, runways and taxiways, for passenger buses, service and technical vehicles. The majority of the traffic will be buses transporting passengers between the terminals and their aircraft.

Jan 1, 2005

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

The paper examines the value of very small-scale indigenous gold mining operations to developing countries. The paper looks particularly at this type of activity in two neighbouring countries, Papua New Guinea and the Philippines, considering technical, economic, social and environmental aspects.

Jan 1, 1990

A dedicated tunnel construction version of the Caterpillar 328D LCR compact radius excavator is proving highly productive on the A9 Autoroute construction project near Visp, in Switzerland. It is the first machine of its kind to operate on a Swiss contract and uses a special dedicated front attachment designed and constructed by German Caterpillar dealer Zeppelin. The machine offers a powerful, stable and compact solution for tunneling contractors. A rear overhang of just 305 mm (12 in.) provides a tail swing radius of just 1.9 m (6.2 ft). The 328D LCR is ideal for the restricted working areas within a tunnel construction site. The machine is equipped with the wide tracks from the 330D L conventional crawler excavator, ensuring maximum stability when operating. In addition, the boom mounting has been moved further toward the center of the machine for the tunnel model, creating an increased lift capacity over the front end compared with a standard 325D L. The boom itself features a robust box section construction, with high-strength steels, additional supporting struts and reinforced bearings for maximum durability. All pins have hard-chromium plating for optimum protection against wear. Stick digging force is a powerful 134 kN, with up to 212 kN of bucket digging force available, for maximum penetration in blasted material. The 328D LCR is also equipped with a heavy-duty dozer blade as standard. This ensures outstanding stability when working and providing a useful secondary tool for clearing and leveling within the jobsite. Two 45° tilting mechanisms in the boom construction, allow the boom to be swung to 45° on either side of the machine. So the specially designed attachment linkage provides increased rollback for access to the roof of the tunnel. A Caterpillar CW45S mechanical quick-coupler allows rapid changes between specialist tunneling attachments, standard Caterpillar buckets and a range of Caterpillar work tools. The machine is powered by a Caterpillar C7 diesel engine. This six-cylinder EU Stage IIIA diesel motor [ ] offers 8 percent more power than its predecessor, with 140 kW (190 hp) available at just 1,800 rpm. Caterpillar?s ACERT combustion technology results in lower fuel consumption and reduced exhaust emissions. However, the tunnel machine is also equipped with a diesel particulate filter as standard, to further cut exhaust gases within the tunnel working. The 328D LCR is designed for use in transport tunnels of 6.8 m (22.3 ft) in height. With the tunneling boom in place, the machine has an operating weight of 42,540 kg (93,783 lbs), yet retains a transport height with the tunnel boom of just 3.9 m (12.8 ft). Transport width with 600 mm (23.6 in.) track shoes, is just 3.2 m (10.5 ft). On the A9 tunnel contract, the machine is being used by a consortium of Swiss and Austrian companies working for the canton of Valais? Routes Nationals Construction (RNC) department. The 31.8-km (19.7-mile) A9 Autoroute construction project will connect Sierre in the west and the town of Brig to the east. The tunnel that is bypassing the town of Visp is just one of a number along the mountainous route.

Jan 1, 2009

By Ian Martin

A precious metals refinery’s switch to personal computer-based, three-dimensional piping design saved many hours in the design of a South African precious metals refinery. Bateman Minerals and Industrial provided engineering, procurement and construction management services for Impala Platinum Limited-Refineries’ new $60 million refinery in Springs, South Africa. This project is one of the largest platinum refineries in the world. Bateman evaluated a new design method during this project that involved developing a three-dimensional model for the project. The new method saved time by reducing the man-hours required to generate complete project documentation, including plans, sections, isometrics and material takeoffs. The new method also saved design and construction time by allowing designers to detect clashes before construction began.

Jan 1, 2000

By Clyde L. Brown

The ignition source of fires and explosions in coal mines is sometimes difficult to explain because resulting widespread destruction often erases valuable evidence that might reveal the cause. However, through years of experience, investigators have been able to piece together enough evidence to establish the reasons and, thereby, have been equipped to recommend corrective or preventative measures. The pattern of hazards is not constant. It changes with the development of new practices and new equipment. Important among the new hazards to coal mining are those introduced by electricity. In addition to the dangers of electric shock, fires and explosions from heat and arcs, and premature blasts, certain others have developed as a result of stray electric currents from direct-current traction systems. The conventional direct-current power-distribution system in coal mines is conducive to electrolysis damage to mine tracks, metallic pipelines, grounded power conductors, and structures in a position to become conductors of stray currents. The voltage drop resulting from power demand on intentionally grounded power conductors and accidental grounds on insulated conductors are common sources of stray currents in coal mines. Uncontrolled electric cur-rents flowing through the earth and metallic structures can be a menace, and these contribute to the estimated $6,000,000,000 annual loss caused by corrosion. The purpose of this publication is to discuss some of the electrolysis hazards in the coal-mining industry and to outline corrective measures to alleviate them.

Jan 1, 1962

By Gustav Nillson

There is a difference in design parameters between steel linings and rubber linings for grinding mills. The basic design parameters for rubber are described and a comparison is made between steel and rubber in different applications.

Jan 1, 1979

By W. H. Goghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, end control of anthracite-line fires, it was observed that the carbon monoxide disappeared from a scaled fire area much more rapidly than could be explained oil the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance; (1) That the carbon monoxide was oxidized at temperatures below 150° C, by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

By Kazunori Matsushita, Frank Vespi, Emi Walder, Mitsuo Nozu

During the runway expansion project at the Fort Lauderdale-Hollywood International Airport in Florida (FLL project), therewere complicated geotechnical issues with a number of cavities in the limestone-loose sand mixed ground thatexisted in many areas below the existing ground. Collapsing the cavities and compacting the runway foundation to secure the take-off and landing of aircrafts was a necessary requirement for the project. The Mammoth Vibro-Tamper (MVT) which produces less vibration and noise level, was proposed and accepted as the alternative to the originally specified Deep Dynamic Compaction (DDC) for the runway with its length of 1.5 miles and area of 570,000 square yards. In this report, the shallow compaction effect and reduced ground vibration with the MVT are presented in comparison with the DDC which was utilized on the same project in a different area of the airport. INTRODUCTION MVT was developed by Fudo Tetra Corporation in the 1960’s and has been widely used in Japan (more than 14,400,000 square yards). For example, at the Kansai International airport, a large area including aprons was compacted with the MVT. It is capable of compacting up to approximately 5m in depth by using a heavy steel plate (3m x 3m) and a strong vibrator motor (V-180, 10Hz) on top of the steel thick plate with specified time duration. We were involved in densification work with the MVT at the Fort Lauderdale Airport Project (Figure 1) from June, 2012 to February, 2014. Deep Dynamic Compaction (DDC) was originally specified as the compaction method to secure the relative density over 70% in every 2,000 square yards grids, however, we proposed the application of MVT to reduce the vibration risk and it was accepted as the alternative (Figure 2). The compaction work was completed in February 2014, without causing any delay in regard to the residual settlement due to the high embankment (H=60ft=18m).

Jan 1, 2018

By T. Lenarcic, R. Svrkota, J. M. McNeal, E. Prohic, S. Pirc

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Surface drainage samples, the usual media employed in mapping national territories, cannot be used for the geochemical mapping of carbonate terrains because there is no regular surface-drainage pattern on karst. Suitable sampling media have been studied in Yugoslavia, one-third of which consists of karst terrain. Sampling designs for the work were based on analysis of variance techniques. During initial investigations of various sampling materials in NW Yugoslavia sediment and aquatic moss from karst springs, along with soil, were established as the most appropriate media. Modified sampling procedures were then carefully applied along the entire Yugoslav karst belt, which includes terrains of contrasting topography, climate, pedology and vegetation. The studies indicate that climate and relief do not systematically influence the geochemical composition of soil. Regional and local variability was assessed for 21 chemical elements and the feasibility of producing stable regional geochemical maps was determined for a number of elements on the basis of sampling aquatic moss and sediment from karst springs and soil

Jul 1, 1991

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

By S M. Loewen, J J. Fuykschot

Located in the north-west of Kazakhstan is a world-class podiform chromite deposit. Donskoy mining and beneficiation complex (DGOK), a branch of Kazchrome TNC, which is a subsidiary of the Eurasian Resources Group (ERG) operates two underground mines in this area, one of which is the ‘10th Anniversary of Kazakhstan Independence’ (DNK) mine.The mine currently applies the gravity caving mining method, producing 1.8 Mt/a of ore utilising a slusher layout and rail transport to the hoisting shafts. The deeper zones form the largest mineral resources at the DNK mine and are planned to be developed in the next several years. At this depth, the generally poor ground conditions, combined with the high in situ stress state will potentially lead to extremely challenging mining conditions.This paper describes a technical study undertaken by SRK to determine the possibility of increasing the maximum production rate from the currently envisaged 6.0 Mt/a to 7.2 Mt/a, and to reduce the time taken to steady state production.Based on a newly created 3D model, the inclined caving method was proposed for the largest orebodies. This method, presently not implemented at any operating mine, although planned for two other projects, was deemed very suitable to deal with the weak rock mass characteristics and the plunging morphology of the mineralisation.Dassault Systèmes’ GEOVIA’s Footprint Finder software (a module of GEOVIA’s PCBC™) was used to determine the caving zones and production schedules. The total mine design was completed in Deswik software, and resulting schedules combined in Excel.In addition to the use of an inclined caving method, several other suggestions were made to increase the productivity of the mine, such as the application of a conveyor belt system transporting multiple material types, teleremote technologies and the application of thin sprayed liners to reduce the swelling of the rock mass.CITATION:Fuykschot, J J and Loewen, S M, 2016. Inclined caving option for the DNK mine, Kazakhstan, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 669–682 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Amanda Elioff

Success of the Gold Line Eastside Ex-tension rail tunnels in Los Angeles, CA has prompted the Los Angeles County Metropolitan Transportation Authority?s (Metro) planning new rail lines to include underground alternatives. The Westside Extension Transit Corridor alternatives include up to 27 km (17 miles) of subway to be constructed in soft ground. The routes will require construction in Los Angeles? ?potential methane zone,? which was not considered for subway construction until recently. Slurry face tunnel boring machines (TBM) will likely be specified.

Jan 1, 2009