Search Documents

By Hua Hou, Xiaofeng Niu, Wei Liang

"The explicit finite difference (EFD) method is used for calculating the casting temperature field during solidification. Because the time step is limited, the computational efficiency of the EFD method is lower. In order to improve the computational efficiency, a fourth-order in space and second-order in time model based on the equivalent specific heat method and the alternating direction implicit (ADI) method is established. The degree of similarity between the simulation results and the experimental results is analyzed. The results show that the simulation results of this high order mathematical model are close to the experimental results.IntroductionThe 3D heat transfer equation of temperature field during solidification process is as the following: [1-3]."

Jan 1, 2013

By E. L. Frueh

AMAX Base Metals Research & Development, Inc. has developed a process for treating copper-nickel mattes to produce copper cathodes and a pure nickel sulfate solution. In this process, the input matte is preleached in a copper sulfate electrolyte bleed solution so as to dissolve nickel from the matte and cement copper from solution. The preleach leaves a substantially pure nickel sulfate solution. The residue from the preleach is roasted to less than about one percent sulfur. A portion of the calcine is leached with sulfuric acid to make a copper sulfate solution for input to the tank house. The residue from this leach and the remaining calcine are smelted to form a bimetallic (copper/nickel.) anode. The anodes are electrolytically refined and copper is preferentially deposited on the cathode while the nickel reports to the electrolyte, A bleed stream is taken from the electrolyte and used in the preleaching of the input matte. This process produces high purity metal streams while consuming less energy and smaller amounts of reagents as compared with other matte processes.

Jan 1, 1983

By M. Misra

The volume of low-level contaminated soil at the. Department of Energy's Nuclear Weapon Sites are in the order of several million tons. Most of the contaminants are uranium, plutonium, other heavy metals and organic compounds. Selected Physical separation processes have shown demonstrated potential in COD Centratingthe radio nuclides in a small fraction of the soil. Depending upon the size, nature of bonding and distributions of radio nuclides, more than 90 percent of the radio nuclide activity can be concentrated in a small volume of fraction of the soil. The physico-chemical separation processes such as flotation in a mechanical and microbubble tall column cell have shown, promising applications in cleaning up the high volume contaminated soil.

Jan 1, 1995

By Melvin A. Jennings

Ion-exchange technology for precious metals recovery is at a turning point. Some very exciting technology has been developed in the past five years which should lead to commercialization of the process. Ion-exchange will allow not only for the recovery of gold and silver, but also will allow for the recovery of cyanide form plant tailings. This process may soon be competitive with Merrill-Crowe for silver and once this occurs, it will become the process of choice.

Jan 1, 1991

By James D. Navratil

Advances in hydrometallurgy require the introduction of new separation and purification processes, but they can be complex, costly and energy intensive. Chromatographic processes have low energy requirements and possess very high separation efficiencies. However, they have not yet made the great industrial impact that might be expected from their benefits. The large-scale and difficult separation of rare earths would greatly benefit from an improved continuous chromatographic operational device. Truly continuous, multicomponent chromatographic separations may be achieved by means of the continuous annular chromatograph. Work has been Initiated at The University of New South Wales involving the improvement and development of such equipment for the separation and purification of rare earths.

Jan 1, 1990

By Alexander I. Raitchenko

"An electroconductive viscous liquid may flow in laminar or turbulent regime under Lorentz-force generated by the intercrossed electric current and magnetic field. When there is a starting flat layer between hard and free boundaries with surface tension the spatial Lorentz-force can create a specific stationary regime of flow: the plane free surface will transform into the wavy one, and the movement in the depth will be not laminar and not turbulent, but this regime will be characterized by organized forms with indications of ""rolling of long cylindrical drops"". Wave-length is determined by the viscosity, the density, the surface tension, the average thickness of layer, and Lorentz-force. ·The limit of wavy regime is determined by most long of wave which is directly proportional to the critical value of specific flow and inversely proportional to the kinetic viscosity. The proper critical value of Reynolds number is determined by the dimensionless combination containing surface tension, density, viscosity, and Lorentz-force. The mentioned dimensio.nless combination in our case is some criterion substituting the known Kapitsa number for case of the thin viscous liquid layers under gravity. Spreading of admixture by mechanism of wavy regime is more rapid than by common diffusion or by laminar flow. The suggested conception can be a contribution into the theoretical basis for elaboration of some specific liquid metals technologies."

Jan 1, 1999

By Robert A. Medower

This paper will review the operational benefits of applying contemporary control technology to balance the blast to a cupola. Reported benefits from existing installations include reduced channelling, higher pour temperature, reduced oxygen consumption, lower coke consumption & reduced emissions.

Jan 1, 2001

By Katsuyasu Sugawara, Takuo Sugawara, Shin-ji Abe, Tadakazu Kagami

"In order to clarify the mechanism and to obtain the fundamental data for heavy metal recovery from an incinerator ash by chlorination, pure chemical reagents, zinc oxide and lead oxide or the fly ash blended with calcium chloride and silicon dioxide were heated up to 1000°C in a nitrogen stream. Thermogravimetric curves of the samples with the chlorinating reagents indicated that solid-liquid reactions accelerated the chlorination and release of metals from the solid phase. The formation of liquid phase of calcium chloride played an important role on effective recovery of zinc and lead at lower temperatures below 800 °C. Although zinc and lead could be decreased in the incinerator ash without chlorinating reagents, addition of chlorinating· reagents enables the removal of metals in high extent· at lower temperature.IntroductionFly ash is discharged about 3,000 tons/day (about 110 million tons/year) from incinerators of municipal solid waste in Japan and mostly fly ash is disposed in landfills. Fly ash includes heavy metals e.g. zinc and lead. Since untreated fly ash caused hazardous leaching problems, Waste Disposal and Public Cleaning Law was revised in 1992, fly ash being designated 'specially controlled' general waste. Fly ash must be disposed by the following suitable, intermediate four methods: [I] Cement- Solidified Method, [2] Immobilized Chemicals Method, [3] Melting Solidified Method, [4] Acid Leaching Method, permitted by the Ministry of Health and Welfare, Japan."

Jan 1, 2000

By K. S. Kumar

FLS miljø, Inc. markets, designs and supplies particulate collection devices for dusts, fumes, and mists; In this paper, the application of both wet and dry electrostatic precipitators (ESPs) in smelting, and roasting plants is discussed.

Jan 1, 1998

By Roger N. Kust

Removal of heavy metals from industrial process streams is becoming increasingly important for _the recovery and reuse of values in process tails. Technology has been available for several years which removes heavy metals, from dilute (0.1-3.0 g/L) streams, as hydroxide or hydrated oxide sludges, allowing discharge of washed cakes with up to 60% solids. This paper reports on improvements to this technology which now allows treatment of streams with metal concentrations in excess of 60 g/L while eliminating the need for thickeners. Streams containing copper, iron, aluminum, chromium, nickel, zinc, cobalt and lead have been successfully treated.

Jan 1, 1992

By Andrew Campbell, Michael Reed

"WorleyParsons has used Discrete Event Simulation methods in conjunction with more traditional process models to assess the performance of copper smelting operations. This work was performed to determine the plant capacities and suitability of proposed debottlenecking options including accounting for the planned and unplanned (breakdowns) shutdowns in the various parts of the plant and supply chain. This paper outlines the methods used along with demonstrating the benefits of selecting a feasible option and minimizing capital and operating costs.IntroductionTraditionally for de bottlenecking studies of smelters and other process plants, a mass balance is performed based on continuous operating rates and expected operating hours. Smelters have several points of failure that will restrict, if not take the entire plant offline. By using a more detailed model, validated against plant experience, bottlenecks can be demonstrated and strategies to remove them to increase plant availability and economic.The modeling simulates the plant performance in real time, and by performing enough simulation the expected long run performance of the plant can be estimated. The models have been built using ExtendSim which is a powerful Discrete Event Simulation software package that is ideally suited to the batch and semi-batch processes and events that occur within smelter operating environments. The value of performing this work is that the operational performance of the plant can be assessed ensuring production targets are met, without using excessive capital outlay."

Jan 1, 2013

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By R. G. Reddy

The oxidation kinetics of A13Ti intermetallics have been studied at the temperature range of 850°C to 100O0C in pure dry oxygen. The oxygen diffusion rates were investigated using TGA method. Parabolic rate constants were calculated. The oxidation scales were analyzed using SEM, EDS and X-ray diffraction. A continuous A120, scales with a little TiO2(rutile) were formed on the intermetallic surface. The A13Ti intermetallic exhibited excellent oxidation resistance among the Ti-Al base intermetallics.

Jan 1, 1997

By Hidenori Okamoto, Katuto Itoh

"Nippon Mining & Metals' Hitachi Refinery refines 40% of the anodes produced at its Saganoseki Smelter & Refinery. Its current annual production stands at 180,000tons.The refinery always endeavors to increase productivity. One of the outcomes of its efforts is an originally developed automatic short-circuit detector used to inspect short-circuits between anode and cathode. The detector is designed to inspect the 56 pairs of anode and cathode in a cell by fluxgate sensors at once. It inspects 564 cells, automatically and un-manned, and gathers data to be put into a computer. The development of the detector led to a reduction of man-power and achieved a detection accuracy superior to that of a hand-held gauss-meter. In addition, statistical and historical processing of the data enabled early detection and early recovery of the cells with poor efficiency.The new system also contributed to raising the refining capacity and reducing the unit steam consumption, because it is possible to inspect even the cells covered with thermal insulation sheets.IntroductionInspection of cells is an important component of the operation management of a tank-house. At the Hitachi Plant, it used to be carried out by two workers who walked on and checked all the cells of its tank-house once a day to find out any short-circuits in the cells, using hand-held gauss-meters. They inspected about 33 thousand pairs of cathodes and anodes a day and removed nodules by hammers. This method had following problems:it needed much manpower.the walk on the cells sometimes deranged electrodes positions.there was radiation-loss connected with the inspection due tothe fact that the workers were obliged to uncover thermal insulation sheets on the cells while inspecting."

Jan 1, 2000

By Heinz Giegerich

This paper deals with a new development in recycling second generation catalytic converters, namely metal substrate converters (MSC). It describes a patented dismantling process, whereby the MSC is segregated into it's three components outer steel shell, metal substrate carrier foil and ceramic W8shcoat with embedded precious metals.

Jan 1, 1995

By M. Z. Sukiennik

A static method for vapor pressure measurement up to 1450 K and above 1 hPa is presented. The method is designed for equilibrium and kinetic studies of metallic systems, including those with a chemical reaction. Application examples are given for determination of activities in condensed phases, and heterogeneous reaction rates and equilibrium constants.

Jan 1, 1993

By Kanchan Mondal

"Methanol, lower hydrocarbons, CO, and HCOOH formation have been by the reduction of CO2 with H2. Un-catalyzed electro-reduction requires a significant overvoltage. An alternate route has been conceptualized. Production of hydrogen from water can be achieved by chemical oxidation of a metal in water followed by oxidation of the hydronium ion by the released electrons to form hydrogen radical. It is hypothesized that circumventing the problem of the formation of hydrogen molecule is essential while having the hydrogen radical to react with CO2 forming methanol, etc. This may be possible by a bimetallic catalyst acting as a galvanic couple, wherein one metal acts as the electron donor for the production of hydrogen radical while the other acts as a catalyst for the reduction of CO2. This may enhance the reaction rates. The current concept circumvents the need for an external electric field unlike the electrochemical process.IntroductionUtilization of carbon dioxide as a raw material, not only as carbon sources but also as useful chemical feedstock is a more holistic approach to reduce air pollution by flue gases (1-3). Several methods have been proposed to maintain the concentration of atmospheric CO2 or to reduce and recycle it. One of these is the chemical fixations using catalysts. The conversion of CO2 to methanol by hydrogenation over copper containing catalysts is one of the most widely studied subjects in this area. The limitation in this reaction is the low conversion of CO2."

Jan 1, 2008

By Xingye Guo, Yeon-Gil Jung, James Knapp, Zhe Lu, Jing Zhang, Li Li

La2Zr2O7 is a promising thermal barrier coating material due to its low thermal conductivity and superior high temperature stability. In this work, Bilayer La2Zr2O7 and conventional 8 wt% yttria stabilized zirconia (8YSZ) coatings were deposited using plasma spray technique. Both singlelayer La2Zr2O7 and double-layer 8YSZ/La2Zr2O7 coating architectures were designed. Thermal cycling and thermal shock tests were used to evaluate coatings’ thermomechanical properties. All La2Zr2O7 coats were delaminated in the furnace cycle test in less than 20 cycles. This is because residual thermal stresses accumulated during thermal cycling. In the jet engine thermal shock (JETS) tests, the SCL La2Zr2O7 and DCL dense 8YSZ/La2Zr2O7 coatings were fully delaminated. In contrast, the DCL porous 8YSZ/La2Zr2O7 coating sample only partially delaminated on the edge. This is because of the porous 8YSZ layer provides strain compliance. The findings will help to propose efficient thermal barrier coating systems.

Jan 1, 2016

By Cecil Harriss

Philip Environmental Services Corporation's (Philip's) innovative fluidized bed thermal desorption system recovers mercury from contaminated soil. Referred to as the Thermal Recycling System, Philip has constructed a mobile thermal desorption system that has a processing rate up to five tons per hour. The system includes a continuous-feed system, all radiant heat, inert gas atmosphere, hot gas filter, two-stage cooling, and a water treatment system. Based on treatability studies, the processed soil can meet cleanup objectives as low as two milligrams per kilogram and passes the mercury toxicity characteristic leaching procedure test.

Jan 1, 1996

By Liu Chunpeng

The new technological process developed is by means of thermal plasma arc smelting to obtain high grade Ni matte directly from Ni-Cu concentrates containing 6-7% nickel and 3-8% sulfur. In comparising with conventional smelting and converting processes the plasma arc smelting process has many advantages over conventional processes, such as lower energy consumption, lower capital investment and free from SO, pollution by transforming the sulfides into elemental sulfur with microwave irradiation under controlled oxygen potential, moreover, the process is simple and easily controlled due to less magnetite troubles in the operation. Therefore, this new technological process can be used as an alternative way to conventional process for Ni-Cu concentrate smelting. The main economical technical index is summarized in Tabal 1. Table 1 Main Ecnomic-technical Index

Jan 1, 1993