Search Documents

By Truan-Sheng Lui, Li-Hui Chen, Hao-Wen Hsueh, Fei-Yi Hung

"Since Ag wires have similar hardness and bonding properties to Au wires, they can be applied in some pads. In the present study, the annealing effect (at 225°C~275°C for 30min) on the tensile mechanical properties of silver wires with f=23µm was investigated. In addition, the micro-structural characteristics and the mechanical properties before and after an electric flame-off (EFO) process were also studied. Experimental results indicate that with annealing temperatures of more than 250°C, the silver wires possessed a fully annealed structure, the tensile strength and the hardness decreased, and the elongation was raised significantly. Under the thermal effect of EFO, the necks of the Ag balls underwent recrystallization and grain growth was induced, and the annealed Ag wires had a shorter zone of HAZ (220µm). The bonding strength and the neck-strength of the Ag wires were more than 7gf and possessed excellent bonding properties.IntroductionThermosonic ball bonding is one of the preferred processes for electronic packaging to connect a semiconductor chip and a lead frame by a thin metal wire. At present, gold wire and copper wire are the preferred interconnect materials to bond with the aluminum metallized wafer pads [1, 2]. Since gold is expensive and the reliability of copper is poorer [3], the study of silver wire has attracted a lot of attention already. In addition, the inherent properties of high ductility and low hardness of silver as well as its workability effectiveness compared to gold, have made it a preferred alternative .[4, 5]"

Jan 1, 2012

By Zhuoqing An, Qi Li, Zhancheng Guo, Yanling Zhang

Fluidized bed is an important iron-making reactor, especially for the finely sized iron-bearing materials. However, defluidization caused by sticking between particles extremely limited its wide spread commercialization. In this paper, apparent viscosity was put forward to express the ability of particles to resist movement, which is reasonably considered as the comprehensive results of interaction between particles. Meanwhile, an experimental measuring method of apparent viscosity of particles was proposed, during which the torque exerted on the rotating blade in a particle layer is measured, and then the apparent viscosity is obtained based on the motion equations of powder particles. Further, the apparent viscosity of iron particles was measured by using of this method, and the effects of shape, size, and temperature were examined. The data can provide important information for understanding when and why defluidization happened.

Jan 1, 2015

By Alexandre Chagnes

The extraction properties of two synthesized cationic exchangers, i.e. bis (1,3-dibutoxypropan-2-yl) phosphoric acid (BiDiBoPP) and bis(1,3-diisobutoxypropan- 2-yl) phosphoric acid (IPA), have been studied for the liquid-liquid extraction of Co(II), Ni(II) and Mn(II) contained in 1 M HCl. A comparison of the extraction properties of these extractants diluted in kerosene with Cyanex® 272 shows BiDiBoPP and IPA extract advantageously at lower pH than Cyanex® 272 and a better Co(II)-Mn(II) separation is achieved using BiDiBoPP or IPA than with Cyanex® 272.

By A. C. Mollison

In November of 1983 a fire inside the autoclave caused the curtailment of operation of the Kidd Creek pressure leaching facility. Subsequent repairs and recommissioning of the autoclave in 1984 allowed Kidd Creek to increase its production of zinc as originally planned. This paper describes the operation of this process from 1984 to 1988 and details major mechanical work carried out on the vessel in 1.988:

Jan 1, 1990

By James E. Hoffmann

Oxidative pressure leaching is gradually supplanting other techniques for the decopperizing of slimes. The reasons for this include: much more rapid reactions, more compact equipment, a reduced environmental burden, and perhaps most important, a much lower final copper concentration in the decopperized slimes. This paper will discuss the reactions occurring during decopperization, the acidity and temperatures encountered and the techniques employed for discharging non condensable gasses. A spreadsheet is provided which allows adjusting the operating conditions depending upon raw (undecopperized) slimes composition, solids concentration and lixiviant composition. A typical process equipment flowsheet is provided along with a process narrative.

Jan 1, 2000

By Yonghua Li, Fanling Meng, Weitao Zheng, Xiaodong Wang

The NiTi thin films were deposited onto copper substrates by magnetron sputtering. Tensile tests were carried out on CSS-44100 electron universal test-machine. X-ray diffraction profile Fourier analysis method has been used to study the mechanical properties of deformation NiTi thin films. The surface micrographs of the NiTi thin film were obtained using scanning electron microscopy (SEM). It has been found that the dislocation density and the deformation storage energy density increased with elongation increased. Microhardness was calculated from the dislocation data. The results showed that the microhardness values were not in a good agreement between calculated values and measured values. The oxide layer on the surface of NiTi thin film affects the measured values of microhardness. The Vickers hardness measured values are larger than the calculated values. The experimental results showed that a series of parallel cracks grew in a concerted fashion across the thin film and the cracks were equally spaced.

Jan 1, 2015

By W. K. Connor, O&apos

The U.S. Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory (INEL), conducted over 30 hours of melting tests to vitrify simulated low-level radioactive wastes from the INEL Radioactive Waste Management Complex (RWMC). Five separate waste compositions were investigated, each consisting of noncontarninated soil from the RWMC and surrogate materials used to simulate the actual buried wastes. The RWMC soil and five waste compositions were melted in a 50-lb, single-phase electric arc furnace with a water-cooled shell. These tests were conducted to determine melting parameters in preparation for a large-scale melting campaign to be conducted in the Bureau's 1-metric ton (mt), water-cooled-wall, 3-phase electric arc fumace. Bulk chemical composition was determined for each of the feed materials and for the slag, metal, fume solids, and offgas furnace products, and distributions were calculated for the key elements. The material balance for the furnace operation indicates that from 63 to 84 pct of the feed reported to the slag. Cerium, used as the surrogate for the radionuclides in the wastes, demonstrated an extremely strong affinity for the slag product. Although slag temperatures as low as 1250° C were recorded when melting the RWMC soil, temperatures in excess of 1600° C were necessary to achieve the fluidity required for a successful slag tap.

Jan 1, 1994

By Subagyo

The condition of slag in a pyrometallurgical reactor is vital to ensuring control of the process. A new technique based on multivariate image analysis (MIA) of digital images has been developed to provide an online measurement of important slag characteristics, such as the presence of exposed metal, the presence of solid phases, and temperature. This paper shall describe the technique and provide some results from analysis using industrial plant data.

Jan 1, 2003

TiO2 and Ti/TiO2 thin films were deposited on a quartz substrate by laser ablation of Ti02 and Ti targets using Nd:YAG pulsed laser. After sulfurization of the Ti02 film in H2S or CS2 gas at 1273 K for 1 hour, the surface atomic structure was changed. Furthermore, the Ti/TiO2 film was successfully prepared by the subsequent ablation of Ti and TiO2 targets. The morphology and structure of the films were characterized by XRD, XPS and AFM analyses.

Jan 1, 2003

By T. Nakamura

TiO2 and Ti/TiO2 thin films were deposited on a quartz substrate by laser ablation of TiO2 and Ti targets using Nd:YAG pulsed laser. After sulfurization of the TiO2 film in H2S or CS2 gas at 1273 K for I hour, the surface atomic structure was changed. Furthermore, the Tirri02 film was successfully prepared by the subsequent ablation of Ti and Ti02 targets. The morphology and structure of the films were characterized by XRD, XPS and AFM analyses.

Jan 1, 2003

By Tadafumi Adschiri

"Supercritical water can provide an unique reaction atmosphere for synthesizing metal oxide nanoparticles. Due to the drastic change of properties of water around the critical point, including density, dielectric constant and ionic product, the reaction phase with O 2 or H2 gas and the reaction rate and equilibrium can be varied to synthesize new materials or define particle morphologies. In this work, hydrothermal crystallization experiments are performed with several types of flow apparatus that allow convenient manipulation of variables such as temperature, pressure, and residence time. Key features in the flow modes and material preparation are discussed. The proposed supercritical hydrothermal synthesis method has the following desirable features: i) nanoparticles can be produced, ii) morphology of the produced particles can be controlled with small changes in pressure or temperature, and iii) a reducing or oxidizing atmosphere can be applied by introducing oxygen or hydrogen or other gases. An overview of this method is given for functional material synthesis of significant industrial interest including barium hexaferrite magnetic particles, YAO/Tb phosphor fine particles and lithium cobalt fine crystals.IntroductionHydrothermal crystallization, a method of metal oxide formation from metal salt solutions, is typically used at temperatures ranging from 373 K to 473 K. We are developing a new process for hydrothermal crystallizations that uses temperatures in the range of 673 K to 723 K, which is just above the critical temperature of water1 • 8 • In this work, we refer to this process as supercritical hydrothermal synthesis. The supercritical state of water allows one to vary reaction rate and reaction equilibrium by shifting the dielectric constant and solvent density with pressure and temperature. From of our research on material production in supercritical water, we have identified the following specific features of the supercritical hydrothermal synthesis method: (i) ultrafine particles can be produced, (ii) morphology of the produced particles can be controlled to some extent with pressure and/or temperature, and (iii) a homogeneous reducing or oxidizing atmospheres can be provided by introducing gases, such as O 2, H2, H2O 2• and so on.1"

Jan 1, 2000

By R. Padilla, M. C. Ruiz, R. Villa

"Bismuth is an impurity in copper minerals where it occurs mainly as the mineral bismuthinite (Bi2S3). In smelting of copper minerals, most of the bismuth reports to the white metal, as a result, a substantial amount of bismuth accompanies the copper to the electrorefined cathodes. Thus understanding the behavior of Bi2S3 at high temperatures is crucial to eliminate bismuth before electrorefining. In this paper, some experimental data on the decomposition/volatilization of bismuthinite in nitrogen- oxygen atmospheres is discussed. The results indicated that in nitrogen atmosphere, bismuth volatilization occurs through a fast decomposition of bismuthinite to metallic bismuth and sulfur with subsequent volatilization of bismuth in the range 850-1100 °C. Similarly, in the presence of oxygen, bismuthinite decomposes to bismuth too, followed by oxidation to the non-volatile bismuth trioxide at temperatures higher than 750 °C. Both, temperature and partial pressure of oxygen affect significantly the bismuth volatilization and the oxidation rates.IntroductionCopper sulfide minerals are the major source for the production of metallic copper by pyrometallurgical processes, which are the dominant processes in the production of copper by selectively oxidizing the sulfide sulfur to SO2 and the accompanying iron in the concentrates to iron oxide, which can be conveniently removed as a stable slag.Generally, copper concentrates contain some deleterious minor elements such as arsenic, antimony, bismuth and lead, which are present as sulfides. These elements depending on their concentration may originate problems in the copper smelting processes and they can ultimately lead to a final copper product with unacceptable high levels of impurities.During the treatment of these copper concentrates by smelting, the impurities generally distribute themselves in the condensed and gas phases and they are eliminated mainly through the gas phase [1-3]. Thus, smelter off gases contains substantial amounts of volatilized impurity elements. For example, in the case of bismuth, the estimated distribution of bismuth in flash furnace smelting [2] was 15 % in the matte, 5 % in the slag and 80 % in the gas phase, and recently, for Outokumpu flash smelting Davenport [3] reported the distribution of bismuth as 30-75% in matte, 5-30% in slag and 15 -65 % in the off gas."

Jan 1, 2011

By G.A Subagyo

The condition of slag in a pyrometallurgical reactor is vital to ensuring control of the process. A new technique based on multivariate image analysis (MIA) of digital images has been developed to provide an online measurement of important slag characteristics, such as the presence of exposed metal, the presence of solid phases, and temperature. This paper shall describe the technique and provide some results from analysis using industrial plant data.

Jan 1, 2003

By Jinrong Zhang

Fresh cyanide solution was treated by near UV light with the assistance of photocatalysts. Cyanide was oxidized mainly to cyanate. Photochemical behavior of the anatase and rutile forms of TiO2 was compared. It is found that anatase has a much higher activity than that of rutile. Bubbling of oxygen in the reactor showed no appreciable increase in cyanide oxidation, implying that the reaction is surface controlling. A very interesting finding in this study is that a natural mineral, ilmenite, can replace chemical titanium dioxide as the photocatalyst. Ilmenite without any treatment did not catalyze the oxidation of cyanide. But, after being roasted at high temperature with oxygen, the oxidation was enhanced dramatically. The mechanisms of photooxidation of cyanide and the roasting of ilmenite are proposed.

Jan 1, 1991

By Patrick R. Taylor

The synthesis of high-purity ultra-fine barium strontium titanate powders (BST: BaO6Sro.4TiO3) has been performed in a non-transferred are D.C. thermal plasma reactor. Slurries of aqueous solutions of dissolved barium and strontium nitrates and solid titanium dioxide powders were used as precursors. Oxygen and argon were used as carrier gases, and pure argon and combinations of argon and nitrogen were used as plasma gases. The plasma torch power was varied, as well as the oxygen flow rate and the total molar concentration of the precursors. A graphite plate was designed to protect the torch electrode and lower the level of impurities in the product. A thermochemical analysis of the Ba(NO3)2-Sr(NO3)2-TiO2-H2O-O2 system was performed to predict the conditions for the formation of BST and the feasibility of the reaction, The powders collected from the different sections of the reactor were characterized using Transmission and Scanning Electron Microscopy, X-Ray Diffraction, and ICP chemical analysis. The powders produced showed high conversion to BST, ultra-fine particle size (< 30 rim) and high purity, which makes this a potential process to produce ceramic materials for electronic devices.

Jan 1, 2003

By Itavahn Alves da Silva, Jose Dimas de Arruda, Amanda Aparecida Fátima Arruda, da Silva de Souza, Carlos Antonio da Silva, Varadarajan Seshadri, Samuel

The knowledge of the flow field inside a continuous casting mold is essential to improve operational efficiency of the process and also to achieve better inclusion control. Physical modeling, PIV technique and CFD have been employed to assess the velocity distribution in the metal- slag interface region in a slab mold. The analysis of results shows how higher casting velocity and lower immersion depth of submerged nozzle can lead to higher turbulence in the slag-metal interface. The effects of density difference between slag and metal and interfacial tension between the phases have been highlighted.

Jan 1, 2016

By Kazuki Morita

Dissolution mechanism and solubility of chlorine in the oxide melts, such as CaO-SiO2-Al2O3 (-Na2O), Na2O-SiO2-Al2O3 and CaO-SiO2-FeO systems, have been equilibrium technique was employed with controlled Po2 and PCl2, (Po2 = 10-6 -10 19 atm, PCl2 10-6 -10-13 atm at 1673-1748 K). The solubility of chlorine in the 40mass%CaO-40mass%SiO2- 20mass%Al2O3, slag was found to vary in proportion to Pb2/ w and pc/z/p&apos; which proved that chlorine dissolved in the melts as C1 anion. Hence, the chloride capacity (CCI-), indicating the ability of molten oxide to absorb chlorine, has been defined as; The Ccl value was observed to increase with increasing slag basicity and temperature, and showed a reasonable relationship with that Of CS2-. Based on the result obtained in the present study, chlorine distribution during incineration with slags was predicted quantitatively.

Jan 1, 2003

By Susumu Okabe

Mitsubishi Continuous Copper Converter employs the top blowing lance system for the continuous supply of reaction gases into the molten bath. In order to avoid the excessive refractory wear caused by the melt splash without loss of the reaction efficiency, the furnace design and the blowing condition should be optimized. Empirical equations which correlate the splashing rate on the&apos; side wall with the dimensions of the furnace, lance position, lance size, gas velocity and bath properties were obtained by by the physical model study, and compiled into a computer program. The computer program is effectively utilized for the analysis of the actual operation and for the optimum design of new furnaces.

Jan 1, 1998

By J. J. Rush

Neutron scattering and analysis techniques are extremely powerful, often unique, probes for the characterization of the amount, location, bonding states, and dynamics of hydrogen in all classes of materials. Developments over the past decade at the NIST Center for Neutron Research and elsewhere have greatly increased the sensitivity and dynamic range of neutron methods. In this paper, we provide a flavor of the capabilities of modem neutron instrumentation for the study of hydrogen in a number of technologically interesting systems, including metal hydrides, fuel-cell materials, fullerenes, and disordered carbons.

Jan 1, 2002

By James R. Myers

A source of clean gas containing sulfur dioxide and sufficient oxygen for conversion to sulfur trioxide is essential to the production of sulfuric acid. SO2 containing gases obtained from roasting sulfide ores are heavily contaminated with inorganic dust and volatile impurities. If not removed, these contaminants will reduce product acid quality, foul the catalyst beds and mist eliminators, and accelerate equipment corrosion. This paper reviews conventional gas cleaning systems for metallurgical acid plants, followed by a discussion of modern systems utilizing DynaWave Scrubber technology. This technology is based on a unique approach togas scrubbing that can concurrently accomplish several gas cleaning/processing tasks. Scrubbing liquid is injected into the gas stream to create a "Froth Zone". This is a region of extreme turbulence, with a very high rate of liquid surface renewal. It efficiently removes both particulate matter and gas contaminants, and is also a cost effective quenching device for gases as hot as 1250 o C.

Jan 1, 1992