Search Documents

By D. E. Walsh

The behaviour of gold particles on a spiral was studied using radioactive gold tracers. The method allowed the effect of particle size, particle shape, pulp density, feed rate, and splitter settings to be studied. Although the method has been successfully applied to other gravity concentrators, it was found that reliable results were more difficult to obtain on the spiral. However, these preliminary results show that provided suitable precautions are taken, the technique is capable of providing valuable information that cannot be obtained by conventional studies, and could be used to better optimize spiral performance.

Jan 1, 1992

By L. M. Nuelle

Rare earth element (REE)-and gold-bearing breccia pipes are a potentially significant economic target in the Pea Ridge iron ore mine, Washington County, Missouri. The Pea Ridge deposit is one of eight known volcanic-hosted iron ore deposits in the Middle Proterozoic St. Francois terrane, which are similar to the Olympic Dam-type deposits of Australia. The iron orebody is steeply dipping, tabular-shaped, and cuts across the host rhyolite. The footwall of the deposit is zoned from the massive apatite-bearing magnetite core outward to heterolithic breccia, pseudobreccia, specular hematite zone, to an extensive silicified zone. The hanging wall is zoned from the massive magnetite core outward to a heterolithic breccia, pseudobreccia, and an amphibole skarn zone. The REE-rich breccia pipes cut through the various lithologies along the footwall at or near contacts. They are typically 60 m long, 15 m wide, and extend at least 120 m vertically. The pipes are comprised of fragments of rhyolite host rock, massive magnetite zone, specular hematite zone, and silicified zone rocks supported in a matrix of rock flour, barite, feldspar, monazite, apatite, chlorite, xenotime, and, locally, gold. Total REE oxide content of samples of the ground mass material, which are not diluted with lithic fragments, average about 20 weight percent. Grades from working faces in the mine are lower and average about 12 weight percent. Gold distribution is erratic, but concentrations are as high as 371 parts per million.

Jan 1, 1991

By George W. Toth

In a recently completed research project for the U.S. Bureau of Mines - Twin Cities Research Center, a computerized costing procedure for uranium in situ leach mining was developed by the NUS Corporation. This costing procedure, termed a cost model, employs a process engineering approach for estimating total project costs as well as equipment and manpower requirements for uranium in situ leaching operations in either Texas or Wyoming. 80th capital and operating costs are generated by the model along with the overall production cost/pound U3O8 subject to a known rate of return. Conversely, rate of return on equity can be solved for, subject to a given price of yellowcake. During the course of the research effort, this cost model was applied 50 typical site conditions in Texas and Wyoming. Sensitivity rests were conducted for numerous key parameters to determine the cost influence attributable to incremental changes In parameter values. The results of these sensitivity tests along with a description of the in situ leaching cost model have been documented as Bureau of Mines, Mineral Research Contract Report No. J019912, "Cost and Sensitivities Analysis for Uranium In Situ Leach Mining," dated March 1981.

Jan 1, 1981

By G. C. Knutsen

The Post deposit is located in Eureka County, Nevada, about 37 km (23 miles) northwest of the town of Carlin. Post occurs on the Carlin Trend, a northwest alignment of 14 major gold deposits, each containing more than three tonnes (t) (100 000 ounces) of gold. Deposits of the Carlin Trend are epithermal, sediment-hosted, disseminated gold occurrences, collectively containing more than 622 t (20 million ounces) of gold. Three major gold producers active on the Carlin Trend are Newmont Gold Company (NGC) (12.4 t/400 000 ounces of gold per year), Western States Minerals Corporation (WSMC) and Pancana Minerals joint venture (1.56 t/50 000 ounces of gold per year), and Dee Gold Mining Company (1.4 t/45 000 ounces of gold per year). The Carlin Trend has also been referred to as the Lynn-Railroad Mineral Belt. This district is characterized by open-pit mineable, micron-sized gold, hosted in Paleozoic sedimentary rocks. Six geological subdistricts comprise the Carlin Trend, each characterized by differences in host lithology, structural controls, alteration assemblage, or style of mineralization. The six geologic subdistricts include, from south to north, Bullion (Railroad), Rain, Maggie Creek, Lynn, Bluestar-Goldstrike, and Bootstrap. With the exception of the Bullion subdistrict, which was primarily a producer of base metals, each sub-district contained mineable reserves in excess of 31 t (one million ounces) of gold.

Jan 1, 1987

By Dirk van Zyl

It can systematically assess if the control and management systems designed for protection of sensitive ecosystems are adequate. The results of the assessment can help to identify key elements in the project that pose higher risks due to uncertainties in design. These assessments can then be used to make recommendations to further manage and reduce risks as the project is developed. QUALITATIVE RISK ASSESSMENT The general principles of a risk assessment are well summarized by Kaplan and Garrick (1981): "In analyzing risk we are attempting to envision how the future will turn out if we undertake a certain course of action (or inaction)." Fundamentally, therefore a risk analysis consists of an answer to the following three questions: What can happen? (i.e. what can go wrong?) How likely is it that that will happen? If it does happen what are the consequences?" Risk assessments can be performed using various levels of sophistication depending on the amount and accuracy of data available. A qualitative risk assessment uses descriptors throughout to express the level of risk. The definitions of the descriptors are presented in terms of the magnitude or concentration of contaminants. The results of a qualitative risk assessment can be used to: a)Document the evaluation and decisionmaking process. Although differences of opinion may exist about the definitions of the descriptors, the process is well-documented; b)Express the relative risk associated with specific activities or design elements; and, c)Select those failure modes or release mechanisms that may result in significant risks. These mechanisms can then be further developed in quantitative risk assessments. A qualitative risk assessment can be performed in a systematic approach using four steps (Van Zyl, 1987): A qualitative environmental risk assessment can be used to describe the risks associated with the development of a new mine and to make an evaluation of the adequacy of its design for environmental protection. The relative magnitude of risk associated with selected failure modes and exposure/consequence scenario assessments is the final result of a qualitative risk assessment. These failure modes are based on site specific areas and components, and mining and construction phases. The four steps of a risk assessment (hazard assessment, exposure assessment, consequence assessment, and risk characterization) are used in the development of a qualitative risk assessment. Relative magnitudes (using a five point scale of negligible to high) for each step, can be quantified in a qualitative risk assessment. Development of the descriptors for the relative magnitudes in each step is a very important part of a qualitative risk assessment. The success of a qualitative risk assessment depends on the adequacy of the information base and the subjective judgements made in each step. The quality of the risk assessment is, therefore, dependent on the experience of the assessors. A mining project in a sensitive coastal environment is presented as an example to demonstrate the application of a qualitative risk assessment. INTRODUCTION Environmental impacts from mining operations have been a significant factor in the last century. This was especially the case prior to the development of a better understanding of environmental processes and the potential impacts of acid rock drainage (ARD), and associated heavy metals, or the uncontrolled disposal of tailings and waste rock (Smith, 1987). Much care has been exercised over the last two decades in designing and operating mines to limit the environmental impacts as far as possible. All new mines are specifically designed with mitigative methods to manage such potential environmental impacts. Attention is directed to ARD impacts, safe disposal of mine waste rock and tailings, transportation and storage of chemicals and fuels, and final reclamation. A qualitative risk assessment can be used to address all project systems and activities that may potentially pose a risk to the environment.

Jan 1, 1992

By M. T. Ityokumbul

The effect of reaction conditions on the desulphurization of oil sand coke residues has been studied. The variables investigated were temperature, reaction time, heat transfer resistance, and mode of caustic soda addition. The results obtained show that oil sand coke desulphurization increases with temperature, reaction time, and heat transfer rate. In an oxidative environment, coke combustion during molten caustic leaching (MCL) commences at temperatures above 500°C. The mode of caustic addition has no effect on coke desulphurization.

Jan 1, 1995

By Ted DePooter, Mun Wei Leong, Chad Frederick

Downtown Bellevue Tunnel (DBT) is part of Sound Transit’s $3.7 billion, 14-mile light rail transit system from downtown Seattle, across Lake Washington, to the cities of Mercer Island, Bellevue, and Redmond. The tunnel was the first Sound Transit East Link project and posed significant construction risk. This paper discusses implementation of design changes to the soft ground tunneling method, implementation of several technologies such as the use macro-synthetic fiber initial shotcrete lining, use of spray-applied waterproofing, and use of shotcrete for the final tunnel lining. These efforts allowed for significant time and cost savings to the project.

Jun 13, 2021

By S. C. Schmelter

The destabilizing effect of water pressure on rock mass stability is examined quantitatively by the finite element method. A coupled code that accounts for the simultaneous effects of rock mass deformation and transient fluid flow is used for this purpose. The traditional soil mechanics assumption of an incompressible fluid is shown to be untenable for the analysis of porous, fractured rock slopes. A Mandel-Cryer effect, a transitory but elevated and potentially destabilizing water pressure following a cut, was not observed.

Jan 1, 1997

By Enrique Jelvez, Nelson Morales Varela, Christian Ihle, Joaquin Silva

All mineral beneficiation processes require water for its execution. Therefore, the availability and adequate management of water are key to the existence of any mine operation. However, many mines’ operations are affected by water scarcity and risk an increase of operational costs or even production in some cases. This paper proposes a model to minimize the losses of water due to evaporation and re-absorption by adjusting the active and inactive periods of the discharge in different points of the tailing. When applied, the model determines optimal or nearly optimal discharge operation in all the scenarios that were evaluated.

Jun 25, 2023

By X. K. Jiang

Upgrading molybdenite ore can be technically difficult and expensive if talc is a major impurity in the ore. The layered structure of molybdenite and talc decreases the surface specificity of floatation and suppression agents, thereby making molybdenite ore beneficiation inefficient if under some wet processing methods. However, oxidic talc surfaces may be distinct from the sulfidic or oxysulfidic molybdenite surfaces, such distinction related to electron work functions and/or densities of electron donors/acceptors sites. If such differences are present, the upgrading of finely sized molybdenite ore by dry triboelectrostatic methods may hold advantages over traditional wet methods.

Jan 1, 1999

By Bruce H. Mason

The exploration for a commercially acceptable deposit of limestone is consid¬ered by many to be a relatively easy task; however, trying to locate a zone of high calcium limestone of economic thickness within a formation, which outcrops only in a narrow band varying in width from a quarter mile to ten miles, adds considerably to the normal problems experienced during an exploration program. The existence of varying glacial and karst features in the outcrop area intensified the problems encountered and complicated the interpretation of the economic value of the deposit. This paper highlights a recently completed five year exploration program during which approximately 3,900 acres of ground in seven civil townships were evaluated as potential sources of high-calcium limestone. Details are given with respect to the final site chosen and the methods used in determining the suitability of the site. This site exhibited many karat features and several methods were utilized to determine the effect of these features on the gross characteristics of the deposit. Aerial photography for both mapping and interpretation were utilized. Black and white panchromatic photography, black and white infrared and color infrared photography were flown. Resistivity, diamond core drilling and close-interval angering were used to supplement the information obtained from the aerial photography.

Jan 1, 1974

By T. Cantwell

Techniques useful in operations, analysis are applied to the problem of planning an exploration program. The model used treats mineral exploration as a Markov process, and maximization of gain is the criteria determining the optimum program. The mathematical description of the model and the optimization are first worked out. Application of the mathematics to several simple examples is given. Finally, comparison of the data necessary to use this operations analysis with the available data shows that the method can only be a guide to planning an exploration program.

Jan 1, 1962

By L. J. Tucker

The magnetite orebody at Pea Ridge strikes NE-SH and dips at about 800 to the SE. The ore is high grade magnetite with a strike length of over 600-m and a maximum width of over 180-m on some of the levels. The shape and the mineral content of the iron orebody have been fairly consistent so far. The iron ore and surrounding basement rocks are Precambrian in age. These rocks are usually very competent, about 400-m of sediments lie over the ore.

Jan 1, 1991

The most common method used for cleaning the fine fraction in today's coal preparation plants is froth flotation. Past research and practice has found that froth flotation achieves excellent separation efficiencies for fine coals having only a small fraction of middling particles. However, its efficiency decreases sharply as the concentration of middling particles increases due to the flotation of high-ash particles having a small amount of hydrophobic coal present at the coal surface. Since gravity-based processes are much more efficient at treating middlings, the application of centrifugal washing for fine coal cleaning has been studied with an emphasis on the primary cleaning of fine circuit feed. Results will be shown from a parametric study using a Falcon centrifugal concentrator which reveals that the separation performance is a function of particle size, bowl geometry, feed solids content, and feed rate.

Jan 1, 1994

By H. S. Chang

A three-dimension two-phase (air and dust) computer model was developed to model air velocity and respirable dust distributions in the longwall faces. This paper describes the derivation of the model including the model features, mathematical equations and boundary conditions. Example simulations were also performed for two longwall faces where measured respirable dust and air velocity distributions were available. The results indicated the model can simulate the mine conditions fairly accurately.

Jan 1, 1996

By S. M. S. Azghdi, K. Barani

The effect of microwave treatment on the surface roughness and wettability of chalcopyrite (CuFeS2 ) and on the chemical composition of its surface was studied. The microwave source was a conventional multimodal oven with frequency of 2.45 GHz and maximum power of 900 W. Pure chalcopyrite specimens and purified chalcopyrite concentrate were used in this study. Analysis using atomic force microscopy showed a decrease in the surface roughness of the chalcopyrite after microwave radiation. This decrease may be due to oxidation of the surface and formation of iron oxide. Moreover, the surface wettability of the chalcopyrite mineral increased with increasing duration of microwave radiation, which was in good agreement with the micro-flotation mass recovery results. The increased wettability of the surface may be attributed to the decreased surface roughness by microwave radiation. Analysis using scanning electron microscope/energy-dispersive X-ray spectroscopy indicate that after microwave radiation, the contents of sulfur and iron increased whereas that of copper decreased on the surface of the chalcopyrite, significantly changing the average atomic number of the chalcopyrite surface.

By A. M. Gaudin

In a recent paper we have reviewed principles and applications of measurement methods for contact angles and their hysteresis (22). In this paper we apply these methods to a system consisting of rutile, an organic liquid (benzene, decane, or dodecane) and water. Surfactant (dodecylamine hydrochloride) was used at various concentrations and various pH values.

Jan 1, 1964

By R. W. O. Kersten

The shrinkage method of stoping with pillar support has been used at Agnes Gold Mine since mining commenced. Until recently, rock instability did not have any detrimental effect on safety or production. Presently sill pillars are failing not only on the current production levels, but also in shallower old worked-out areas. The incidence of failure raises the question as to whether the pillar dimensions are adequate at the current working depths and what their size should be at greater depths. The effect of pillar dimensions on the economics of the mining operation is of paramount importance because of the amount of ore that can be left unmined.

Jan 1, 1982

By R. L. Atwood

This paper discusses the metallurgical and Manufacturing input to Merrill-Crowe plants. Topics treated are pregnant solution chemistry, clarification, degassing, zinc addition, product filtration, accounting, and costs.

Jan 1, 1985

By Arthur S. Cornford

According to Arbiter (Reference 1), the ball mill was invented by Brückner in Germany in 1876 and was first used in the United States on ores about 1905. The basic concept was a simple rotating cylindrical drum in which the tumbling action of the charge of material and grinding media resulted in size reduction of the material. Despite the very low mechanical efficiency of this method a number of factors have caused the tumbling mill to remain, by far, the most widely used piece of equipment for mineral grinding. The principal factors influencing this situation have been simplicity of design, ease of manufacture, ready adaptability to familiar material handling layouts and the absence of practical alternatives acceptable to the industry. In the early mills, the material was ground in batches, the mills being charged and discharged through doors in the shell. The shell was supported by means of solid trunnion shafts resting in plain bearings and the drive was accomplished through one of these shafts. In some later batch mills, the mill shell was supported on rollers which were also used to drive the mill. At an early stage, continuous operation was made possible by feeding and discharging the mill through hollow trunnions, the method still in most widespread use. The mechanical and structural design of the early mills was not an onerous engineering task. Norse sense and good practical knowledge were key qualifications. The mill shells had to be heavy enough to withstand the physical abuse they would receive in the field and the bearings had to have low enough unit pressures and sufficient wear retol to ensure several months of operation before the need for replacement occurred. When these requirements were satisfied, stresses developed in the equipment during operation were insignificant and the majority of structural failures were probably due to the use of inferior materials in manufacture. Over the years, the ever present demand for increased productivity has resulted in a steady Increase in the size of units of production equipment, including grinding mills. Arguments have been presented elsewhere, for and against the Idea of a high throughput single line grinding operation as opposed

Jan 1, 1972