Search Documents

By J. R. Klaehn, M. Shi, T. E. Lister, L. A. Diaz, J. S. McNally

Since 2019, approximately two dozen international battery recycling companies have been operating at the commercial or pilot scale [1]. However, current process capacity does not exceed 100,000 tons of end-of-life (EOL) lithium-ion batteries (LIB) per year, and the current recycling rate is only about 5% in North America [2-3]. Recycling metals from EOL LIBs is not only essential to waste minimization and environmental stewardship, but also a source of critical materials, which can contribute towards supply chain stabilization. LIB recycling can be roughly divided into three categories: direct recycling, pyrometallurgy, and hydrometallurgy. Direct recycling seeks to retain as much of the manufactured effort with minimum chemical processing [4]. The evolution of battery designs and chemical compositions are challenges to this approach [5-6]. Pyrometallurgical processes are robust and flexible allowing a broad spectrum of batteries with minimum pre-processing requirements. Some of the matrix issues are solved through combustion of some constituents. Smelting is strongly tied to fossil energy and air emissions are a concern. In addition, pyrometallurgical processes are not stand alone, as hydrometallurgical refining normally required to separate and recover the metals of interest (Co, Ni, and Cu) from the produced alloy and Li from the slag [7]. Hydrometallurgical processes can be highly selective and efficient in recovering high purity materials [8]. In general, hydrometallurgical processes are considered cleaner and less costly than high temperature processes [4,9-10]. Extensive chemical consumption and waste generation significantly increase the operating costs and overall environmental impact of the hydrometallurgical processes [11]. Leaching of metals from LIBs is dominated by the mixture of sulfuric acid (1 to 4 M H2SO4) and hydrogen peroxide (1 to 15 wt.% H2O2) [10]. Although organic acids have been tested as lower environmental impact alternatives, the reported pulp density operations are low < 60 g/L [10-11]. For the H2SO4/H2O2 leachates, high leaching efficiencies >90% are reported for Co, Ni, Mn, and Li from cathode materials at temperatures over 40 ⁰C and pulp densities between 30 to 200 g/L [9-10]. H2O2 acts as reducing agent to convert Co+3 and Mn+4 into their soluble forms, Co+2 and Mn+2 [12]. Despite the claims of H2O2 being a clean reducing agent [13], production of H2O2 has significant environmental impacts as determined by life-cycle analyses [13-14]. Moreover, the costs and risks associated with H2O2 transportation and storage cannot be ignored [15].

Mar 2, 2022

By W. M. Aubrey

The use of solid fuel in shaft furnaces to indurate iron ore pellets was originally considered a necessary evil, which the industry worked long and hard to eliminate. Since then changes have taken place in furnace design and operating practices that have led us to our suggestion that solid fuel additions could again be used. In essence, what has happened is that the developments which made it possible to operate without solid fuel have also created new operating conditions favorable to the effective use of solid fuel. Because these new conditions* were brought about in part by the desire to eliminate solid fuel and because the development was a gradual one, the industry failed to reassess its position and for years neglected the possibility of returning to solid fuel.

Jan 1, 1967

By Gary E. Slagel

The federal Office of Surface Mining (OSW) has undertaken an effort to revise many of their permanent program regulations. Numerous procedures for compliance are being rewritten to allow for greater flexibility while meeting the requirements of the Surface Mining Control and Reclamation Act. This study investigates, for certain select provisions, the cost differential between complying with the original OSM standards and the more flexible, state-specific standards being allowed in many of the revised regulations. Estimated cost savings that could be realized under a few of the revised regulations are substantial and should provide a basis for seeking revisions to the state regulatory programs.

Jan 1, 1982

By F. W. Petersen

Slurry reactors are being used extensively throughout the chemical, biochemical and mineral processing industries. This paper describes the interaction between fine ore particles and granular porous adsorbents such as activated carbon and ion-exchange resins in a stirred tank reactor. Gold and silver cyanides were used as adsorbates to detect changes in the mass transfer characteristics of the adsorbents, which were ashed to determine the loading of ore particles. A simple kinetic model incorporating film diffusion, intrapanicle diffusion ~d the adsorption equilibrium, was used to interpret kinetic data and to estimate the effect of slurry conditions on the diffusion parameters. It was observed that the equilibrium loading of fines in the adsorbents was independent of their concentration in the slurry. Furthermore, the presence of these panicles inside an adsorbent decreases the effective diffusion of gold or silver cyanides into the adsorbent matrix. When fine suspended solids are present in the reactor, a decrease in the effective availability of the superficial surface of the pre-saturated adsorbent panicles for mass transfer from the liquid phase was observed. This newly defined surface availability factor was dependent on the concentration, panicle size, and the zeta potential of the fine particles in suspension.

Jan 1, 1993

By Marco Sonnenschein

Belt conveyors for tunnelling are industry standard and key to high performance of TBM drives. Conveyors reduce traffic in the tunnel and increase safety in the tunnelling process. This paper will illustrate the state of the art of tunnel belt applications in very long and curvy tunnels like the Coxwell Bypass Tunnel Project in Toronto, Canada.

Jun 23, 2024

By I. R. Miller

The purpose of this discussion is to try to offer some suggestions as to how the zinc and lead markets will perform over the balance of the decade, review some of the factors influencing production and come to some conclusions regarding prices. The past 2 years have been simply awful in terms of consumption, prices and overall profitability for the industry. In looking ahead to the year 2,000, it is probably not a bad idea to look back about 20 years to see where we have been and how we got to where we are. Zinc consumption from 1950 to the early 1970&apos;s increased steadily and rather nicely at an annual average rate of close to 4.0%. It was starting in the early 1970&apos;s that things started to get volatile and at times, difficult for the industry. The general economic boom of the early 70&apos;s was marked by annual consumption rates close to 5.0 million tons, a level not seen again for over 10 years. The First Oil shock of 1973-74 was followed by the sharpest consumption drop in memory. In two years, Western World zinc consumption fell 27%. While our chart shows a rather dramatic recovery thereafter, the average annual growth rate since 1970 has only been a rather modest 1.5%.

Jan 1, 1992

By Rick A. Croote

The objective of the Cerrejon Coal Project is to mine and export a minimum of 15 million metric tons per year of bituminous coal from the Guajira Pennisula in Colombia, South America. Major components of the project will include an open pit mine, 150 km railroad, marine terminal for storage and shipping, and accommodations for the support personnel. This paper primarily reviews the coal handling facilities at the mine and port which will include crushers, conveyors, silos, stacker/reclaimers, and a shiploader. Of special interest is the design concept for unloading bottom-dump railcars, a programmable controller control system with automatic stacking and reclaiming, a linear-type shiploader, and 2.4m wide conveyors running at 5 m/sec.

Jan 1, 1983

By Ulrich Benatzky

Rheinbraun AG, Germany, is the management company of the mining and raw materials division of RWE AG. Rheinbraun&apos;s core business and major functional area is opencast lignite mining in the Rhineland. The characteristic feature of opencast mining is continuous operation using bucket-wheel excavators, belt conveyors, and spreaders. The report gives a survey of the conveyor systems used. In addition to the general performance data of these belt conveyors, this report will deal in particular with major components, such as drive stations and individual mechanical components (e.g., conveyor belts, pulleys, gears, couplings, brakes, scrapers), as well as monitoring systems. Finally, an assessment of the conveyor systems, together with future developments, will be given.

Jan 1, 2000

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By M. W. Springett

During the 1970&apos;s geostatisticians were often accused of not paying sufficient attention to geologic features in the computerised generation of ore reserves. Unfortunately this charge was all -too-often justified and the results of such studies tended to be oversimplified and failed to reveal the full potential of computerised reserve estimation and geostatistical methods. There were some notable exceptions to this trend. Techniques were described that paid a great deal of respect to the geologic characteristics peculiar to certain deposits (Rendu J-M, 1984, Barnes T. E., 1982). At Gold Fields several techniques have been developed for handling the geologic characteristics of ore bodies for reserve estimation purposes. These have developed over time and the evolution of their adoption has been a reflection of our own learning experience from the practical application of computerised reserve estimation on many precious metal s deposits. Problems Typical problems that have been experienced by ourselves and which we have learned to guard against and watch for are: ? "smearing" at geologic contacts ? confusion caused by disparate "selective mining unit sizes" and block sizes ? conflicting estimates generated by field staff using various versions of the polygonal method ? problems in generating meaningful variograms

Jan 1, 1985

The rheological behavior of high concentrated coal -water slurry (cws), a new liquid fuel, is an important factor in the preparation, transportation and combustion. The conventional viscosimeters designed for Use with true fluids are not suitable to the measurement of the rheological behavior of cws. So that a special viscosimeter of tube type for cws was designed and set up in .laboratory. Experiments using two kinds of cws from two provinces from P. R. Olfna were conducted. It is found from test results that the experimental cws possess the rheological character of Bingham fluid and there is the existence of the wall effects which causes the measurement errors. In our former paper published the wall effects were discussed III the light of methods of Odroyd and Jastrzerbsiki to make the correction of the experimental results. But a number of tests are necessary to meet the need of determining the slip coefficient. In this paper the models of the wall slip velocity and the thickness of the slip layer of Bingham fluid were proposed III in theoretical approach which were satisfactorily used in the correction of the measured results of the rheological character of cws.

Jan 1, 1994

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By Virginia T. McLemore

The Black Hawk district in New Mexico hosts an unusual type of deposit: arsenide five-element veins. These deposits are Ag-Co-Ni-Bi-As-bearing carbonate veins with local concentrations of U, Pb, Zn, Sb, and other elements. They are high-grade silver deposits (1000s g/t Ag), but low tonnage (<1 Mt) and difficult to find. By 1881, claims were staked and a town developed. It is estimated that >$1,500,000 was produced in 1883–1893, when Ag prices dropped due to the 1893 Ag panic. Solid Silver Mining Co. produced $600,000 from the Black Hawk mine; one car load contained $28,000 worth of silver! The town of Black Hawk grew to 125 population by November 1883. By the end of 1893, the town was vacant; nothing remains. The district was idle until 1916, and the mines operated sporadically since because of lack of available capital, water issues, and difficulty in finding ore shoots. The area is a favorite for mineral collectors. Tungsten was found in the district in 1935 in quartz veins associated with pegmatites. Metal production from 1881–1960 is estimated as 3,000 lbs Cu, 1,000 oz Au, 1,286,000 oz Ag, and 4,000 lbs Pb. In addition, 10,542 short tons of 2.7–71% WO ore and 615 short tons of fluorspar ore have been produced from the district.

Feb 1, 2025

By WILLIAM M. CROSS, ALBERT ROMKES, BERNARDO MORENO BAQUEIRO SANSAO, Jon J. Kellar

In this research study, the interaction of particles with substrates of different roughness magnitude was investigated. Particle surface treatment, relative humidity (RH), and surface roughness levels were controlled in order to achieve separation of different particles by applying removal forces. Three different approaches to reproducibly roughen surfaces were used. Initially, glass disks were laser engraved to create a reproducible, controlled roughness substrate. However, the laser engraving method produced surface features that were much greater in scale than the particles. These scale differences were such that the substrates produced were not of value to this research. The second option investigated to induce reproducible substrate roughness was to scratch the glass disk using sandpapers of known grain size. A third approach to establish reproducible roughness was to use fine stainless-steel wire mesh substrates. In tests with sanded glass disks, the interfacial energy of plasma-cleaned (hydrophilic) glass beads had a high variation at 40% RH, showing non-uniformity of area of contact between particles and substrates. As the RH increased, it was expected that the interfacial energy of hydrophilic particles would increase, but this behavior was not observed. In addition, comparing the interfacial energy results of hydrophilic particles with hydrophobic particles, a region with significant interfacial energy difference was not identified. In the case of the stainless-steel mesh substrate, the mesh asperities and particle dimensions were comparable. Thus, the smaller particles had more area of contact with the substrate than the larger particles. For the plasma-cleaned (hydrophilic) beads, the recovery values had an average of 92.5% recovery when the RH was between 46 and 85%. For the hydrophobic beads, the average recovery was 19.0% when the RH was between 46 and 75%. Thus, the hydrophobic characteristic of the particle influenced its lower interaction with the mesh substrate. The difference in recovery can be exploited to achieve separation of particles based upon adhesive forces.

Nov 30, 2021

By Earl M. Frizzell

Investigation of mined land characteristics, evaluation of irrigation systems and evaluations by the mining industry determined that irrigation is a feasible method for aiding the revegetation of coal mined lands in the western arid and semi-arid regions (Sherman, et al. 1980). The various regions studied displayed a commonality of characteristics which enables, independent of the site or region, the recommendation of solid-set irrigation. Irrigation should be supplemental by complimenting natural precipitation and should be implemented on a temporary basis. For germination, the vegetation requires application of small amounts of water in a gentle, frequent, and timely manner. For the establishment phase of growth, moisture should be applied and stored in the soil either through pre-irrigation or deep irrigation.

Jan 1, 1985

By K. H. Nimerick

Froth flotation of coal is growing in importance and complexity. Some of the reasons for these changes follow. 1) A need exists for energy resource conservation. 2) Preparation plants are processing widely varying coal -- deep seam, strip and stockpiled either separately or as blends. 3) More fines are being generated because more mines are using automatic mining equipment. 4) It is more practical and economical to remove ash and sulfur at the preparation plant than during utilization.

Jan 1, 1982

By Hoke M. Garrett

The domestic cement industry demands about 550 trillion Btu annually, at a time when reduced fuel use has become a necessity due to the energy shortage. In terms of the overall power picture, that 550 trillion Btu, which includes both fossil and electrical energy, means about 0. 870 of all energy consumed in the U. S. The various factors influencing reduction of this energy consumption are the subject of this paper. Nationally, the energy shortage is being tackled on two fronts--increasing supply and reducing demand. Making cement consumes energy; therefore, the industry cannot join the effort to increase the energy supply except indirectly as noted later. Demand can also be attacked on two fronts--by reducing cement consumption or by reducing the amount of energy required to make cement. The following discussions on reducing cement industry energy consumption center briefly on the prospect of reducing cement consumption followed by a broad evaluation of the potentials for improving cement-making thermal efficiency.

Jan 1, 1974

By G. W. Luxbacher

Coal mine infrastructure is rarely designed solely on the basis of ventilating the underground workings. Instead the optimization of a mining sequence, the minimization of coal quality variation, reduction of coal losses by adapting to property boundaries and geologic structure (seam inclination, roof conditions, coal thickness, etc.) or other similar considerations have formed the objective for mine plant design and layout. Infrastructure development may also reflect a desire to maximize production early in the life of the mine or to permit flexibility in mining according to market conditions. Requirements for coal mine ventilation, established by the 1969 Coal Mine Health and Safety Act, have mandated changes in the traditional concepts of mine plant design in the United States. Mines, in operation prior to the passage of the Act have experienced severe limitations when attempting to adapt the existing mine infrastructure to meet the requirements of the law. In addition the increased quantities of air required, velocity limitations on trolley haulage and belt lines, the establishment of separate intake escapeways and gob area ventilation have com- pounded the inherent complexity in planning mine ventilation systems. Past practices in mine ventilation planning and design are no longer adequate. Given the complexity of today&apos;s ventilation systems, effective planning and design approaches are required. As such, the interrelationship between the overall coal mine plant design and ventilation system design is examined. An approach to ventilation system design constrained by global considerations of mine plant design, is presented. The proposed approach is, however, applicable to the design of new mine ventilation systems as well as to the modification of existing systems.

Jan 1, 1980

By David G. Chedgy

It is probably safe to assume that most operating personnel working in coal preparation plants are exposed to noise levels in excess of the MESA Noise Regulations unless they are wearing ear protection. The excessive in-plant noise levels have received little attention until recently. Noise control has not been an important design consideration in existing coal preparation plants. This situation is rapidly changing as plant owners and plant operators are requiring that new coal preparation plants be designed to provide a safe noise environment for operating personnel and also meet MESA Noise Regulations. This paper discusses the noise exposure hazards, noise generating mechanisms, and some possible noise control solutions for typical coal preparation plants.

Jan 1, 1975

By M. A. Trevits

The explosion hazard presented by methane gas in coal is confronted daily in the mining industry. Research has developed several viable methods for gas control in addition to conventional dilution by ventilation. Such methods include the drilling of horizontal or cross-measure boreholes from a mine opening and vertical boreholes hydraulically stimulated in advance of mining or for gob gas drainage. The long-term production history of five gas drainage installations was studied. Three installations were completed in the Pittsburgh Coalbed: two in West Virginia and one in Pennsylvania. The remaining installations were completed in the Mary Lee Coalbed in Alabama and the Sunnyside Coalbed in Utah. The types of drainage methods utilized included horizontal and vertical boreholes. The length of production studied ranged from 860 days to 36 years. The cumulative production from the five sites was in excess of 155 Mm3, representing a significant volume of gas.

Jan 1, 1985