Search Documents

By Richard E. Hucko

The Coal Preparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals--an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal--to establish grade- recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes--nominal minus 35 mesh (0.5 mm) and nominal minus 100 mesh (0.149 mm)--and subjected to conventional froth flotation. The froth product was then beneficiated by coal-pyrite flotation or HCMS to provide a direct technical comparison of the two processes. At minus 35 mesh (0.5 mm), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a size of minus 100 mesh (0.149 mm) , however, the performance of HGMS exceeded that of coal- pyrite flotation. The separations effected by HGMS were more efficient at minus 100 mesh (0.149 mm) than at minus 35 mesh (0.5 mm). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size, or the process has not been optimized to treat material finer than 35 mesh (0.5 mm).

Jan 1, 1981

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

The Bureau of Mines, U.S. Department of Interior, is currently investigating strata interactions associated with the mining of multiple coalbeds. Strata interactions due to subsidence are a result of undermining. This study involves underground investigations at a mine where room and pillar panels are actively being developed through an area of the Sewickley Coalbed which was subsided by undermining of the Pittsburgh Coalbed. Research to date indicates that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. Consequently, this has led to major roof falls in the active panels, resulting in considerable production delays and supplemental roof support costs.

Jan 1, 1985

By C. I. Basilio

The adsorption of dialkyl di-and mono-thio-phosphinates on gold, silver and gold-silver alloys has been studied in the present work. These reagents, which are selective collectors for sulfide flotation, have been found to improve precious metals recovery from ores. Voltammetric studies have indicated that dithiophosphinate adsorbs on gold at much higher potentials than on silver, while monothiophosphinate adsorbs only on silver. However, both adsorb on gold-silver alloys with the adsorption potential decreasing with increasing silver content. Using FTIR spectroscopic measurements, the surface species formed during the interactions of these collectors have been identified. The results of the electrochemical and spectroscopic measurements have been compared with the contact angle data obtained at controlled potential conditions.

Jan 1, 1992

By Douglas R. Shaw

Normal dodecyl mercaptan was evaluated as a collector for flotation of sulfide minerals and precious metals. The reagent is from the class of normal mercaptoalkanes (n-alkyl thiols), and is commercially available in the form of a mixture of n-dodecyl mercaptan and a dispersant, under the trade name Pennfloat(TM)3. Reported are results of bench-scale flotation experiments on many commercially treated base metal and precious metal sulfide ores. Dosages, points of addition, and flotation pH were among the uariables studied. Most notable results were increased copper, molybdenum, and precious metals recoveries. Dosages of dodecyl mercaptan on some ores were considerably lower than required for conventional collectors.

Jan 1, 1979

By John Newby, Edward Kennedy, Ulf Gwildis

Alluvial deposits of major rivers often provide relatively uniform tunneling conditions. However, these conditions pose specific challenges due to the tunneling behavior of the granular soils as flowing ground, if unsupported. This paper describes the design considerations and construction experiences gained during the Tunnel Boring Machine (TBM) drives for the Annacis Island WWTP New Outfall System in the Vancouver, B.C. metropolitan area. Meeting the design criteria for connecting two (2) deep on-land shafts with an in-river riser manifold required advancing a 5-meter-diameter slurry TBM through the Fraser Rivers sands and at a tunnel invert elevation with a baseline hydrostatic head of 3.4 bar.

Dec 1, 2022

By K. M. Mohamed, R. K. Zipf

The shear strength properties of generic cement foam material and cement foam/concrete interfaces were examined at three testing scales. In laboratory direct shear tests on specimens with average shearing area of 0.006 m2 (10 in.2), the cement foam material had average peak and residual shear strengths of 0.88 MPa (128 psi) and 0.39 MPa (56 psi), respectively. Depending on the concrete strength, the cement foam/concrete interfaces had peak and residual shear strengths ranging from 0.71 to 0.81 MPa (103 to 117 psi) and from 0.27 to 0.29 MPa (39 to 42 psi), respectively. In laboratory direct double shear tests on specimens with average shearing area of 0.084 m2 (130 in.2), the cement foam/concrete interfaces had average peak and residual shear strengths of 0.17 to 0.30 MPa (25 to 44 psi) and of 0.11 to 0.23 MPa (16 to 33 psi), respectively. In large shear tests of simulated cement foam seals with the Mine Roof Simulator (MRS) test frame, cement foam/concrete interfaces with shearing area of 1.486 m2 (2,304 in.2) had average shear strengths of about 0.08 and 0.16 MPa (11 and 23 psi) along the roof and floor interfaces, respectively. The average shear strength through the cement foam material was 0.38 MPa (55.3 psi). Finite element analysis of the large seal tests and the back analysis of the shear strength of full-scale cement foam seals conducted at the NIOSH Lake Lynn Laboratory confirmed shear strength of about 0.14 MPa (20 psi) along the seal/rock interfaces. The study concluded that the structural analysis of cement foam seals should be based on their residual shear strength determined from small laboratoryscale tests of the cement foam/concrete or rock interface and not be based on their peak strength.

Jan 1, 2014

By Robert L. Grayson

An application of goal programming (GP) in evaluation of proposed purchases of major mining machinery is presented. It incorporates historical operating data compiled on mechanical delays to production time. The goal programming technique, which is an extension of integer programming, is used to maximize an objective function. The objective function combines the capital budgeting evaluation methods of net present value, payback period, profitability index, and total net earnings as goals weighted according to a management preference. The GP method gives an optimal solution to a multiple-goal problem. A sensitivity analysis is performed to determine the effect of an increased production forecast or a tightened budget on proposal selection.

Jan 1, 1982

By Melvin W. Jackson

The study of the excavation of large spherical cavities in salt formations first became of interest in 1958 when it was recognized that a large cavity could be of value in the study of the detection or concealment of underground nuclear explosions. Previously unpublished studies are reported in this paper and other studies reviewed relating to the excavation of large cavities in salt by mining ad by solution. Special emphasis is placed on the utilization of the Tatum salt dome (about 22 miles southwest of Hattiesburg, Mississippi) for the proposed site of a large excavated cavity. The U. S. Atomic Energy Commission has recently been studying such a cavity as Project Payette, but no details have yet been published. If Project Payette is determined feasible and work funded, it would eventually involve the firing of a nuclear explosive at the center of a large cavity.

Jan 1, 1969

By John Rajala

The Otjikoto Gold Mine in the Republic of Namibia is located approximately 300 kilometers north of the capital city of Windhoek. The project features surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and recovery of gold. Initial mill design capacity was 2.5 million tonne per annum but then expanded after 9 months of operation to 3.1 million tonne per annum. The technical steps to establish the Otjikoto mill design from process selection in the due diligence stage, through flowsheet development in the feasibility study followed by detailed engineering design are reviewed in this paper along with mill performance during start-up and in 2019.

Oct 30, 2020

By Nikhil Dhawan, Shrey Agrawal

Feldspar, a low-alumina, and abundantly available aluminosilicate source, is explored in this study to extract aluminum and potassium values. The sample comprises lamellar layers of microcline and albite with quartz containing 17.4% Al2O3, 9.67% K2O, and 66.3% SiO2. Mechanical (milling) and thermal (alkali and acid baking) activation are investigated, followed by HCl leaching. The milling treatment up to 6 h is inefficient in phase dissociation and results in ~ 40% Al and K dissolution. The alkali thermal treatment yielded 80% Al and 71% K extraction. Direct precipitation of the dissolved Al and Si values yielded alumina purity of ~ 29%, and silica gelation separated SiO2 and improved alumina product (94% purity, 71% recovery). Acid baking yielded 98% pure alumina precipitate; however, Al and K extraction were limited to ~ 45% and 65%, respectively. The microwave-assisted alkali treatment was optimal with 800 W and 10 min processing conditions yielding 80% Al and 71% K recovery with 2.26 kWh/kg alumina of thermal energy consumption. The final product contains γ-alumina with a specific surface area of 87 m2/ g. Keywords Feldspar · Alumina · Potassium ·

May 18, 2022

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, MSHA began requiring the use of continuous personal dust monitors (cPDMs) to monitor and measure respirable mine dust exposures to underground coal miners. After the cPDM’s implementation, mine operators discovered that it interfered with proximity detection systems (PDSs), thus exposing miners to potential striking and pinning hazards from continuous mining machines. NIOSH was sought out by MSHA and mining industry stakeholders to determine how the cPDM and PDS interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments, and conducted lab evaluations. Some interferences were observed to be caused by electromagnetic interference (EMI) from the cPDM. Results showed that there was no significant interference when the cPDM and the miner-wearable component of the PDS were separated by distances of 6 inches or greater. In this study, the cPDM and PAD needed to be at least 6 inches apart in order for them to be used simultaneously and reduce interference potential. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis such as coal dust exposure, high noise levels, roof and rib falls, the potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 40 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (1,2). Proximity detection systems (PDSs) are designed to alarm miners and stop machine motion in order to protect miners from being struck, pinned or crushed by CMMs(3). Currently, MSHA-approved PDSs, installed on CMMs, are based on the principle of magnetic flux density (B-field) (4,5). The system generates a magnetic field around a CMM and determines the relative distance a miner is from the CMM based on a detected magnetic flux density. A PDS typically consists of multiple magnetic field generators mounted at different places around the CMM, and personal alarm devices (PADs), which are worn by the miners to detect the magnetic flux density. When a miner, wearing a PAD, gets closer to the machine, the PAD detects a stronger magnetic field from the generators and detects a weaker magnetic field when a miner moves away from the machine. The magnetic field generators installed on CMMs typically produce modulated magnetic wave signals at frequencies between 10 kHz and 120 kHz. The magnetic fields are measured by three small magnetic coil antennas mounted on orthogonal axes inside of the PAD worn by the miner. According to Faraday’s Law, the changing magnetic field induces a voltage in each coil antenna, and the voltage values are transmitted from the PAD back to a controller on the CMM wirelessly, typically at a frequency between 400 MHz and 2.5 GHz. These values are then used to determine the distance between the miner and the generators of the machine. Typically this information is used to determine when a miner wearing a PAD is in a warning zone or stop zone which would trigger different alarms and actions such as slowing the machine down or stopping it."

Jan 1, 2017

By Edward H. Peplow

Mr. Chairman; honored guests; ladies and gentlemen: The subject assigned me today by your committee, according to the program, is "the mineral industry and the public land law I have preferred to title the talk, "you can't mine here", for that is the essence of the message we, as an industry, have been getting from so many agencies of the federal government for so long. And, unfortunately, we can expect to hear the same message even louder and clearer -- with increasing frequency in future, unless. Every segment of the industry devotes the necessary time, energy and creative thought to combat successfully the forces that are writing and broadcasting that message. I said that agencies of the federal government are sending the message --- and this, of course, is true, the forest service, for example, and some bureaus of the department of the interior as well as others have appeared in recent years to be abiding by a policy designed to block mineral entry to as much of the public lands as possible and to wipe out existing mining claims.

Jan 1, 1967

By M. Scaggs, L. R. Mendoza

"On January 9, 2014, a large chemical spill occurred on the bank of the Elk River near Charleston, WV. Within hours, the potable water supply for more than 300,000 people was contaminated, and the incident captured national headlines for weeks. Although the primary chemical, crude 4-methylcyclohexanemethanol, or MCHM, is deemed nonhazardous, the impacts of the spill are significant – with all stakeholders, including the public, members of industry, and relevant government agencies experiencing losses. This case highlights the need for a more proactive approach to environmental management, shifting from crisis control and remediation to crisis prevention and risk management. INTRODUCTION On the morning of January 9, 2014, approximately 10,000 gallons of crude 4-methylcyclohexanemethanol (MCHM) leaked from a 48,000-gallon storage tank sitting on the bank of the Elk River near Charleston, West Virginia (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal, and is deemed nonhazardous in terms of transportation and storage regulations and also toxicity (CDC, 2014a). Freedom Industries, Inc., a producer and vendor of specialty chemical products, had acquired the storage facility where the spill occurred from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein & McWhirter, 2014). The spill site was located just over a mile upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a “Do Not Use” order was issued for all customers (WVAW, 2014a). With little information readily available regarding the potential human health effects of MCHM, the US Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the “Do Not Use” order remained in effect for a total of eight days, until January 17, when the WVAW distribution water was confirmed to have MCHM concentrations below this level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at concentrations as low as 0.55 ppb by individuals experienced in odor identification (Rosen et al., 2014); and even individuals with no such training can detect pure MCHM at just 7 ppb (WVTAP, 2014). The fact that this chemical can be sensed at such low levels – indeed far below those considered safe – undoubtedly added to growing public concern. In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until February 25 when MCHM levels were measured below 2 ppb (WVAWb, 2014), and eventually replaced the affected filter media (WVAWc, 2014)."

Jan 1, 2015

By Ernest M. Spokes

Maximum fan efficiency can only be obtained when the fan has the correct combination of size, speed, and blade setting to provide the required flow of air against the mine resistance. As the mine grows older, resistance decreases unless old workings flow is restricted, and new combinations of speed and blade setting or different fan sizes may provide greater economy.

Jan 1, 1977

By Joseph A. Dos Santos

The largest TBM (Tunnel Boring Machine) tunnels are typically along modest slopes, but not always. Occasionally high slope angles are required beyond the capabilities of conventional open trough trailing conveyors. A 2019 project required a large TBM to ascend to an incline angle of 25°. A Sandwich Belt high angle conveyor could easily solve the high angle conveying problem but such a system must include all of the features of the conventional trailing conveyor, particularly the ability to extend with the TBM advance. The writer responded to the challenge and developed a TBM trailing Sandwich Belt high angle conveyor with all of the needed features. The invention (U.S.A. patents awarded October, 2021 and November, 2022) however goes beyond the 2019 project requirements and extends to any high angle incline. This writing first presents the broad Sandwich Belt high angle conveyor development, then its use in various construction and tunneling projects prior to this TBM Sandwich Belt trailing conveyor invention. Finally we present the new TBM Trailing Sandwich Belt high angle conveyor with all of its features and implications.

Jun 13, 2023

By Victoria Vaccarezza, Corby Anderson

The demand for rare earth elements for everyday technology and applications has initiated much research into the extraction and recovery of these rare earth elements. An otherwise unknown group of minerals, eudialyte is a zircon silicate consisting of rare earth oxides (REO), contained in a unique mineral structure and represented by a complex chemical formula. Research into extraction and recovery of rare earth elements involves various beneficiation and hydrometallurgical techniques. The goal of beneficiation being to efficiently liberate and upgrade the REO content, followed by hydrometallurgy to extract the desired elements. This overview will discuss previous research on treating eudialyte group minerals via different mineral processing and extraction techniques.

By John L. Bolles

The Phelps Dodge Corporation's Morenci Concentrator includes facilities for coarse crushing, fine crushing, grinding, flotation, tailing, disposal, concentrate filtering, and drying. The Morenci Concentrator daily throughput is in excess of 60, 000 tons. The ore milled is mainly a medium-hard monzonite porphyry in which the principal sulfide minerals are chalcocite and pyrite. The ore is transported by rail from the Open Pit Mine to the primary crushing plant located at the concentrator site. Ore is side-dumped from 80¬ton railroad cars into a sixty-inch gyratory crusher. The ore is then conveyed to a. 12, 000 ton coarse ore storage bin. Fine crushing is accomplished by four parallel lines of conventionally stacked crushers in open circuit. Each unit consists of one seven-foot standard cone followed by two seven-foot shortheads. Ti% product of the fine crushing plant is distributed by two tripper cars across a fine ore storage bin. The crushed ore is then fed by variable speed belt feeders into thirty parallel, single stage, closed circuit grinding units. Each of the 30 grinding units consists of one 6' x 23' conditioning drum, one 10' x 10' ha l mill and two 54" duplex spiral classifiers as principal equipment. The dry ore is fed into the conditioning drum with water to dilute the ore to a slurry of approximately 78% solids by weight. An aqueous solution of ammonium sulfide is also added to the conditioning drum. The ammonium sulfide primarily acts as a sulfidizing agent. The ore slurry containing the naturally occurring sulfide copper minerals and the sulfidized copper minerals discharges into the feed scoop box of the ball mill, where milk of lime, collector and-.dilution water are added. The ball mill product slurry is gravity fed: to the classifier pool where water is added to obtain the desired classifier overflow product

Jan 1, 1977

By Kurt M. Larson

Future haulage cost projections led Foster Yeoman Limited into developing a fully mobile crushing and conveying system at its Torr Works quarry in Somerset, England. The purpose-built system has an effective throughput of 2,500 tonnes/hour and features an Orenstein and Koppel (O & K) manufactured walking frame, a Fuller-Traylor type 54 X 74 TC gyratory crusher, and unique mobile conveyor modules designed and manufactured by Foster Yeoman. Used in a single-bench operation in this 6 million-tonne per annum limestone aggregate quarry, the system is fed at the production face by 2 Caterpillar 992C loading shovels. The entire system is moved on a daily basis following production face locations.

Jan 1, 1986

By S. S. SHINDE, P. C. JIKAR, N. B. DHOKEY

Mill scale is an oxide waste product of the steel mills, which contains around 70% iron and other allied impurities. In the present context, a dynamic prototype counter current reactor (CCR) has been used for experimentation and simulation of particle bed by using discrete element method (DEM). Mill scale was pulverized to ASTM mesh range 140 (106 μm)/ + 270 (53 μm), and then it was oxidized in CCR to make single oxide Fe2O3 phase by maintaining required thermodynamic conditions such as pure oxygen at 1100 °C. Then this oxidized powder was subjected to reduction reaction in CCR having gas mixture ( H2:N2) ratio of 1:4 at 875 ± 5 °C for filling degree (fd) and reactor revolution (ω) ranging from 5.38 to 16.14% and 2 to 5 rpm, respectively. A creeping fluid flow condition (Re ˂ 1) and natural heat convection (Gr/Re2 ˃˃ 1) has been maintained while undergoing solid–gas reaction. Besides particle bed behavior has been quantified by Froude number (Fr) for the optimum operating window. The simulation was validated by the experimental results of reactor reaction product by X-ray diffraction (XRD) and scanning electron microscope (SEM) images. Prevailing heat transfer mechanism and reduction reaction mechanism has been established for solid–gas counter current conditions.

Nov 22, 2021