Search Documents

The block caving mining method is used to mine large orebodies in weak rock types. The layout for block caving requires that a considerable amount of development is carried out on the extraction drives and drawpoints at the bottom of the caving block. The development further weakens the rock mass, and stability problems arise in the extraction drives and extraction pillars. This paper describes the application of three-dimensional boundary element models in analysing alternative extraction level layouts for a block caving mine. The objectives were to establish whether the use of lateral pillars between drawpoints was warranted, and whether the lateral pillars should be offset or not. The stability of the rock mass within the pillars as well as the stability of the extraction drives were taken into account. The results showed that after undercutting, the horizontal and vertical stresses in the extraction level would be reduced. The lateral pillars would significantly improve the stability of the extraction pillars and extraction drives. There would be a minor improvement in stability if the lateral pillars were offset.

Jan 1, 1987

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988

By T. Wennberg

An elevated location of a paste thickener on a ridge close to the disposal area is considered at a Swedish iron ore mine. About 0.7 M tonnes of thickened tailings are planned to be layered as paste in the vicinity of the thickener over several years with pipeline lengths of up to 900 m after about 20 years. In order to clarify the pipeline pumping characteristics of the tailings product for volumetric solids concentration from 40 to 50%, experiments in loop systems with pipeline inner diameters from 0.063 to 0.152 m have been carried out with various types of pumps. The results and comparisons carried out here showed that the performance of centrifugal pumps cannot simply be related to the rheology, but factors related to pump design and build-up tendencies of material within the pump and other particle properties may be of equal importance. During the first years of operation only one thickener underflow pump is required. The reliability and performance for various pump configurations are planned to be investigated systematically in order to meet the most effective long-term solution for paste thickener operation, pipeline distribution and placement in the disposal area as the discharge point advances over the life of the project.

Jan 1, 2007

This paper presents a quantitative approach to the problem of determining design capacity and field dimensions of underground coal mines using room- and-pillar mining systems. In evaluating these design variables, relationships among mining costs, number of production sections in mines, location of central shafts, mine field dimensions, section production, mine output, and cost of production losses due to underground man-traveling are analyzed. Thereby the unit cost of coal is expressed as a function of the design variables as well as input parameters such as seam angle, seam thickness, seam depth, underground traveling speed of men, mine recovery and plant recovery. The problem is then formulated as a nonlinear optimization model in terms of minimizing the unit cost of coal subject to a set of constraints and solved analytically for flat seams and numerically for inclined seams. Sensitivity analysis of the variables is also included in the paper.

Jan 1, 1987

In many practical situations, the samples available to estimate a block of ore are not located on a regular grid. The sample sizes and orientations are not constant, and the number and relative position of the samples used for valuation of each block change from block to block. Estimation of a block W might be very complex and time consuming if each sample in the neighbourhood of the block were considered individually. A practical solution consists of grouping the samples in blocks Wi (i = 1, 2, . . . n) in the neighbourhood of W, and estimating µw as a weighted average of the mean xi of the samples in Wi. Possible ways of grouping the samples are illustrated in Fig. 1 1.1. More complex patterns can be found in the literature (Krige, 1966) To calculate the kriging estimator of pw, we must be able to calculate the variance of xi, the covariance of xi and xj, and the covariance of xi and pµw. The purpose of this chapter is to show how these quantities can be calculated when we ignore the position of the samples in the block Wi. We consider the samples to be randomly distributed in Wi; kriging with this assumption is known as random kriging.

Jan 1, 1978

The mining rock-mass rating (MAMA) classification system was introduced in 1974 as a development of the CSIA geomechanics classification system to cater for diverse mining situations. The fundamental difference was the recognition that in situ rock-mass ratings (AMA) had to be adjusted according to the mining environment so that the final ratings (MAMA) could be used for mine design. The adjustment parameters are weathering, mining-induced stresses, joint orientation, and blasting effects. It is also possible to use the ratings (AMA) in the determination of empirical rock-mass strength (AMS) and then in the application of the adjustments to arrive at a design rock-mass strength (DAMS). This classification system is versatile, and the rock-mass rating (AMA), the mining rock-mass rating (MAMA), and the design rock-mass strength (DAMS) provide good guidelines for the purposes of mine design. However, in some cases a more detailed investigation may be required, in which case greater attention is paid to specific parameters of the system. Narrow and weak geological features that are continuous within and beyond the stope or pillar must be identified and rated separately. The paper describes the procedure required to arrive at the ratings, and presents practical examples of the application of the system to mine design.

Jan 1, 1990

By W. F. Nothard, J. R. C. Hill

The Rhodesian approach to the vegetating of slimes dams by J. R. C. HILL, B.Sc.(Agric.) (Visitor) and W. F. NOTHARD (Visitor) To prevent environmental pollution from mine dumps, it is necessary to stabilize them either mechanically or biologically. In the long term biological stabilization is more attractive because of its permanent nature. Initially, the basis of stabilization is in the correct siting and construction of the dump. The main toxic factors influencing plant growth on Rhodesian mine dumps are arsenic, antimony, copper, nickel, a high ratio of magnesium to calcium, excessive soluble salts, high pH, and Iow macronutrient content. Root-growth studies in culture solution and pot experiments are used to supplement information on the suitability of plant material obtained from replicated field trials on mine dumps. In addition to the selection of plants for toxic tolerance, it is advisable to provide multiple-layer protection with trees, shrubs, and grasses. Further, a range of different plant species gives greater biological stability. Protection must be provided for young plants against wind erosion and the abrasive effects of windblown sand. Planted wind breaks are preferred to mechanical forms; windrows of garden refuse make good wind breaks and at the same time introduce organic material to the dump and provide a good environment for seedling establishment. The use of artificial fertilizers and sewage effluent is recommended to hasten the development of a complete and protective plant cover.

Jan 12, 1973

Traditionally, the term `total system' design applied to comminution conjures images of a design that addresses the usual business and operational drivers, including health, safety and environment (HSE), capital cost, operating cost, throughput and product size. In terms of the physical process, the mine to customer type studies also exemplifies an approach that satisfies a normal `total systems' approach. As an industry there are drivers that are forcing a re-consideration of what we regard as our total system. This modification of drivers will require changes in approach and implementation to provide the best solutions. Some of the major changes that impact the drivers are shortage of skilled personnel, changing social attitudes to remote mine site work, greenhouse gas emissions (GHGE), quality of available orebodies and geographical location of new mine sites. One approach to the challenges presented by the changing business environment is to expand the system envelope around comminution to ensure that comminution, in its widest sense, helps to meet the new realities. Background to the new drivers and constraints is provided and some of the appropriate responses are examined in relation to the impact on the total system.

Jan 1, 2007

By D. D. Hawat

The locations of potential reserves of chromite ores throughout the world are discussed. Reference is made to the marked changes in international trade in chromite ores during the past ten to fifteen years, and to the change in locality of the production of ferochromium aloys, which is curently largely carried out in the country of origin of the ores. The influence of these changes has been very profound in South Africa, which has the largest smelting capacity and the largest production of ferochromium aloys in the world. A proportion of South African ore is stil exported to meet the demands for the production of chromium chemicals and refractories, including a large tonnage of foundry sands. Ferochromium smelters in South Africa have a capacity of virtualy 1 Mt of aloy per annum. Nearly al this development has taken place since the introduction of the argon-oxygen decarburization (A.O.D.) process for the smelting of stainless steels. Formerly, expensive Iow-carbon ferochromium aloys were required as raw materials, but the AO.D. process, which is being used world wide, permits the use of high-carbon ferrochromium, the main product of the smelters in this country. The production in South Africa of chromium-containing corrosion- and heat-resistant steels is stil on a relatively smal scale, but serious atention is being paid to the exploitation of low-carbon weldable feritic chromium steel.

Jan 1, 1986

By Stephen Hughes

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in the lead and zinc industries, as an efficient and highly flexible pyrometallurgical reactor with accompanying excellent environmental performance. For the processing of lead and zinc bearing feed materials twenty one (21) Ausmelt furnaces are now in operation, under design or under construction. With recent increases in the value of both lead and zinc and an ever increasing focus on the sustainable use of resources, interest in the processing of secondary feed material sources as well as metal containing residues has substantially increased. Ausmelt Technology has proven to be well suited to the economic recovery of values from such sources. This has for example culminated in Ausmelt?s commitment to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This paper describes Ausmelt?s recent developments in the fields of lead and zinc processing, as well as further investigations into new processing areas, including the direct smelting of zinc concentrates. Ausmelt?s TSL Technology can now be regarded as Best Available Technology (BAT) for metal production.

Jan 1, 2008

Actual observations of rockburst damage, together with some theoretical considerations, strongly suggest that conventional approaches to the design of tunnel support are inappropriate where there is a significant seismic risk. The present widely used support systems, which are based on stiff, fully grouted re-bars, are inadequate where rock displacement velocities exceed 1 m/s. It is shown by means of a simple conceptual model that yielding of the support elements is essential to ensure their survival when they are subject to the high strain rates typical of severe rockbursts. The model proposes that the total load in the element is an impulsive tensile force imposed and sustained by a single 'tributary' block ejected from the tunnel wall. The stability of the system is determined from a comparison of the kinetic energy developed by the block with the energy of deformation absorbed by a grouted steel tendon. A novel test procedure was developed for the validation of this approach, and for an examination of the energy-absorbing capacity of stiff and yielding tendons. The results of an initial series of tests showed that the recently developed cone-bolt is an effective yielding device. It absorbs twenty times more impulsive-load energy than is consumed by the complete fracture of grouted re-bar of equivalent strength, and it remains totally unscathed. Importantly, the results demonstrate that the ejection model is not merely an explanatory concept, but can be used as a representative and valid design method.

Jan 1, 1994

By R. P. King

A class of gravity separation unit operations in ore-dressing relies for its operation on the production of a stratified bed. Heavier material gravitates downwards, and separation is achieved by splitting the ore horizontally, with the recovery of a dense stream and a lighter stream. The important ore-dressing unit operations that fall in this class are the jig, the Reichert cone and the pinched sluice. A new quantitative model based on Mayer's potential theory is developed here. This model is developed completely for the simple case of binary mono-size particulate materials, but the extension to units operating with feed material distributed over particle size and density is discussed in principle. The model can be used to predict the performance of these units and is very suitable for simulation. The model is tested successfully against experimental data obtained from a batch jig and a Reichert cone.

Jan 1, 1987

By R. Hoare

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development team's processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement. TSG Consulting advocates a `total integrated system approach' to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007

By T. A. Silva, A. C. Bragança

Lime has been added to the iron ore slurry transported by the Samarco pipeline since its operation start-up in 1977.Initially, internal corrosion was the main concern therefore the reagent was used only for pH correction. Over the last ten years, though, transport of more complex slurries demanded a significantly higher dosage of lime to guarantee adequate rheology control. Several other reagents have been tested for the same purpose yet none has proven to be as effective regarding technical performance, environmental impact and cost. However, an alternative was sought so that the slurry rheology could still be controlled in case lime addition became impracticable. The objective of this paper is to present a technical solution for this matter, which takes into account environmental aspects. It consists of adding soda for pH correction and an organic coagulant as a rheology modifier. The latter is a quaternary ammonium salt which affected the slurry transport properties in the same manner as lime when tested in a laboratory. It showed no plug formation and allowed solid particles to settle, forming a loose sediment after rest. These results indicate a low probability of plug occurrence in the pipeline and the formation of a readily reslurryable sediment upon shutdown of the pumping system. Industrial tests should be performed in order to validate the laboratory results.

Jan 1, 2007

The Copperbelt areas of Zambia and the Democratic Republic of Congo (DRC) have recently been seeing the development of a significant number of new projects. Due to the current economic climate, some of these projects have been delayed but the region remains an important resource for copper and cobalt for future years. Many of these projects will utilize an agitation leach followed by solvent extraction and electrowinning to recover both copper and cobalt. The flowsheet route for copper is fairly well established while the processing options for cobalt vary considerably depending on the final product (metal or salt) the operator wishes to make. The mineralogy of ores in the area is typically associated with high gangue acid consumption during the leaching process. This has resulted in acid availability to the area being constrained and acid prices have risen accordingly. Agitation leach circuits, typically, have a tight water balance which needs to be maintained and a bleed of process liquor needs to be continuously removed from the circuit in order to maintain this balance. This bleed, typically, contains fairly high levels of acid and requires neutralization prior to tailings disposal or secondary metal recovery. It is, therefore, desirable to minimize the acid concentration in this bleed stream in order to decrease total acid requirements and neutralization costs for the process plant. An in depth case study by Cognis and Bateman Engineering evaluated three different flowsheets with the aim of determining relative operating costs between the three alternatives, together with differences in plant capital cost requirements.

Jan 1, 2009

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By G. W. Holl, E. G. Fairon

A review of some aspects of shaft design by G. W. HOLL, Pr. Eng., Associate of the Mine Managers Association of South Africa (Fellow)- and E. G. FAIRON, Pr. Eng., F.S.A.I.E.E., M.I. Cert. M.E.E., M.I.Mech. E., (Visitor) The reasons for the choice of vertical shafts in preference to inclined shafts of comparable capacity are set out, and the conclusion that the former are superior in virtually all circumstances is substantiated. The shapes of vertical shafts sunk during the past sixty years are recorded, and the shapes of those sunk during the past decade are analysed. From this analysis it is clear that circular and elliptical (and quasi-elliptical) shafts are the shafts of the future and that the rectangular shape will conceivably become obsolete. The determination of the size of shaft is discussed and it is forecast that shafts of a diameter of 13 metres and over will probably be sunk without difficulty in the years to come. The depth of the shaft is determined intrinsically by the Mines and Works Regulations applicable to factors pf safety of winding ropes and the design of the winding system. The Blair winder is the most suitable winder for hoisting rock, men, and material from a depth of, say, 3000 metres on an economic basis. Tertiary shafts will, therefore, be unnecessary in future deep-level mining projects at the limit of depth now envisaged. A few other factors relating to shaft design are described.

Rock fall accidents continue to be the main causes of fatalities in the mining industry. The occurrence of rock falls in supported stopes implies a failure of the support system. The failure of the support system in turn implies a failure in design. In this paper, ethical issues associated with engineering design are discussed, with particular relevance to stope support design. A risk approach is introduced that will allow designs to be carried out that are compatible with the acceptable risk defined by the mining company management. The implementation of this approach would overcome the ethical shortcomings of current support design practices.

Jan 1, 2007

Newmont is one of the few remaining large mining companies that was established in the early nineteen hundreds. The company has a long, colourful and enviable history. This paper provides highlights of Newmont?s business and technical history since its inception in 1916, its transition to a ?gold only? company in the early 1990s and progress since that time up until the present day. Details of Newmonts current gold operations and its gold production profile for 2008 are also provided in the paper Over the last 50 years Newmont has developed a host of innovative gold technologies to meet the challenges of treating the complex refractory gold ores, found at the company owned mines in the Carlin region and around the world. Details of the technologies are provided and they include chlorination, roasting, bacterial and pressure leaching, leaching gold with thiosulphate and thiocyanate, N2Tech flotation, HPGR treatment of hard and abrasive ores and, finally, the use of Hydro-Jex technology for improving gold recovery from heaps.

Jan 1, 2009

Notices COMPETITION FOR STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY Each year the Institute offers a prize (or prizes should the entries warrant it) of up to RlOO for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute. APPLICATION AND PRACTICAL OPERATION OF HYDROCYCLONES Dr H. F. Trawinski of Amberger Kaolinwerke, Hirschau, West Germany, gave a very interesting lecture on this subject to an audience of over one hundred, composed largely of members of the Institute, on 15th August, 1973, at the University of the Witwatersrand. ROTARY INTERNATIONAL Applications are invited before 15th March, 1974, for the following awards of The Rotary Foundation: Post-graduate Fellowships Under-graduate Scholarships Awards for Technical Training Awards for Teachers of the Handicapped. NIM REPORTS Report No. 1509 The instrumentation developed for electrochemical studies of the le(Whing of uranium dioxide. Report No. 1550 A fundamental study of the dissolution in (Wid solutions of uranium minerals from South African ores. Report No. 1552 The preparation and analysis of minerals for use as reference material.Progress report No. 2. Report No. 1556 The spectral analysis of solutions.2. The analysis of leach liquors, concentrates, slags, and residues. Report No. 1559 A cost assessment of the production of elemental sulphur by chlorination roasting. Report No. 1562 Application of a flotation model to an industrial plant

Jan 11, 1973