Search Documents

By J. F. Barkley

"A knowledge of the carbon dioxide (002) content of the products of combustion, particularly from the boiler furnace, is very valuable. An instantaneous indication of the CO2 can be used as a useful guide to efficient burning. A permanent record over a. period of time gives a story to the management which tends to keep the operators more alert. Many instruments that indicate and record CO2 have appeared within the last fifteen years. More are about to appear. Although simple principles involving chemical, physical, or electrical qualities, are being used, there is at present a general feeling of uncertainty about such instruments in the boiler room any instruments are bought, run awhile, then lie idle indefinitely.Inquiries as to CO2 machines continually come to the Bureau of Mines from the general public, as well as from other branches of the Government. Some ten years ago a series of tests was made on certain instruments at that time on the market. The following test was made quite recently on four of the newer types, including one using an electrical principle. The four instruments were installed on one boiler each, according to the instructions of the makers, and the recommended routine attention was given them. The test was of a service nature duplicating the conditions under which the instruments ordinarily serve. The boiler that was available for this purpose was practically banked for some hours of the night. This caused the average CO2 for the entire twenty-four hours to be rather low, although it reached the higher ranges of the instruments during the day.Each day the charts were averaged and the results plotted to form the accompanying curve. The record of each instrument is shown by its particular mark, the dot, circle, cross and square being used in addition there is plotted for each day a rectangular area representing 1 % CO2 in height. The proper positions of this area was determined by means of the Crsat. Where the plotted point for an instrument falls within the rectangel its accuracy is within 1/2% CO2, which is considered satisfactory. Where it falls outside the rectangle, inaccuracy is indicated."

Mar 1, 1925

Develop a method to evaluate the effectiveness of coal scam fire surface seals so that potential problems may be corrected at an early stage, before the integrity of the surface seal is lost. Background Surface seals are the primary coal seam fire abatement method being used in the western United States. Surface seals smother a fire by denying it oxygen. The seal is usually constructed by placing a mantle of soil, four to ton feet thick, over a coal scam fire area to exclude air from the fire. The soil is compacted to increase effectiveness, and a soil cement may be used to augment the soil. In some cases, burning coal may be excavated and separately smothered or otherwise extinguished in another area; in other cases, a trench maybe excavated and backfilled with incombustible material to isolate a fire. More often, a surface seal is simply applied over and around the entire known burning area. In the 1950's, the Bureau of Mines administered a large program to treat numerous coal seam Fires across the western United States. Methods used in this program were described in Bureau of Mines Information Circular (IC) 7932, dated 1959. More recently however, various coal seam fires have been treated with surface seals under the direction of state Abandoned Mine Land Reclamation authorities. It has frequently taken years to evaluate the effectiveness of surface seals. By the time problems become evident, it has often been too late to take corrective action within the scope of the original abatement project. For this reason, the Bureau of Mines developed a means for tracking temperature trends at coal seam fire projects to obtain a better and earlier handle on the effectiveness of surface seals.

Jan 1, 1991

Reduce methane levels around the shearer machine during longwall mining by directing more of the available airflow along the face and over the shearer body. Approach To address the entire mining cycle, two techniques were combined to dilute and clear the methane liberated from the face by the shearer during cutting. The first is the modified shearer clearer system, which is used during the entire face pass. This is combined with the walkway curtain which is used only during the headgate cutout. How It Works Methane ignitions are one of the most potentially serious hazards facing longwall mine operators. The high rate of coal extraction on longwall sections can liberate a significant quantity of methane during a pass. The modified shearer clearer is used to dilute methane concentrations along the entire face for both cut directions. The shearer clearer system, originally designed as a dust control technique, uses a series of water sprays located on the shearer body to direct more airflow along the face and over the shearer. (See Technology News issues, #112, #118, and #221). The only change from the original shearer clearer design is the addition of three sprays to the return-side splitter-arm/ shearer interface. The additional sprays help to ventilate the area behind the shearer body.

Jan 1, 1985

By B. Dimitriades

The Bureau of Mines measured the reactivities of 19 hydrocarbons known to be prominently present in automotive exhaust and ambient air in a smog chamber. Results agreed well with those obtained using two other smog chambers. Reactivity scales were developed for hydrocarbons and aldehydes using the results of this work and those of a previous study. Application of the reactivity scales to automotive exhaust samples gave fair agreement between predicted and observed rate-of-N02-formation values; however, predicted and observed ozone yields were neither in agreement nor did they correlate well. This lack of correlation for ozone yield was attributed to the inappropriateness of (1) the individual component reactivity data, (2) the reactivity classification scheme used, and (3) the linear summation method. In seeking to understand this problem and to develop more appropriate reactivity scales, the data were examined from a reaction mechanism standpoint, and further studies were suggested.

Jan 1, 1975

By Parviz F. Rad

The Bureau of Mines conducted groove cutting experiments in marble, lime-stone, granite, and quartzite with a 7-inch disk cutter under a normal thrust of 7,000 lb. The values of muck weight per unit length, specific energy, cutting coefficient, and groove depth for each of these rocks were determined for groove spacings ranging from 0.1 to 4 inches, and from these results the values of optimum and critical spacing were computed" The results indicate that compressive strength may be used to predict some of the cutting characteristics of the independent grooves. Considering all the cutting characteristics, particularly those for the interacting grooves, Shore hardness, coefficient of rock strength, and torsional velocity correlate with cutting characteristics better than do other physical properties. Some of the field applications of the principles established in this report are identified.

Jan 1, 1974

By Thomas E. Marshall, Timothy Batchler, Anthony T. Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

By Kevin Connor

During 1984, minerals exploited in Burundi included gold, kaolin, lime, and peat. Over 1,100 troy ounces of gold was extracted and traded during the year as a result of the lifting of the Government ban on gold mining in mid-1983 and the establishment of an artisan mining program and licensed trading counters. Almost 2,000 tons of kaolin was mined for the manufacture of insecticides. Lime production was for domestic fertilizer applications. Amoco International and the Government signed an accord late in the year for a petroleum exploration program covering 600,000 acres of Burundi's onshore Ruzizi Plain and part of northeastern Lake Tanganyika. Amoco was expected to begin the exploration program by mid-1985. Anticipated program costs could run as high as $200 million.2 The Finnish company Ekono Oy completed its peat industrial energy development studies for the Buyongwe peat deposits of northern Burundi by the end of the year. The project assessed the quantity and fuel quality of 13,000 hectares of peatland and was part of a larger study for developing the Musangati lateritic nickel deposits of Burundi, estimated at 3% of the world's reserves of nickel. The Buyongwe peat would fuel dryers and an electrical generating plant for supplying power to nickel ore processing facilities. Briquetted peat would also be used as a substitute for wood and charcoal, presently the main sources of rural energy in the country and rapidly depleting because of deforestation. The study also evaluated the most economical methods to harvest the peat bogs. The study was financed by the International Development Association (IDA), United Nations Development Program (UNDP), Finnish Aid-Finnida, and the Burundi Government.

Jan 1, 1986

Control dust generated during overburden drilling at surface coal mines using either wet suppression or dry collection systems. Approach For the wet suppression systems, a range of water flow rates was tested over a number of holes. Each hole was drilled at a specific and constant flow rate. A recording flow meter was mounted in the water line near the control system pump. For the dry collection systems, each drill was tested with the front of the shroud set at different heights above the ground. Because of the irregularity of the ground surface, all height measurements were taken at the front of the shroud. Background Wet drilling systems consist of a water tank mounted on the drill from which water is pumped into the downhole air line. The water droplets in the bail air conglomerate dust particles as they travel up the the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole.

Jan 1, 1987

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

Provide an accurate, reliable means for determining when a sealed mine or mine section can be safely reopened after a fire. Approach The Bureau of Mines performed a research investigation that resulted in the development of a mathematical formula for deriving a quantity, called RATIO, which can be used to define when a sealed mine or mine section has returned to safe recovery conditions after a fire. Research Results There were two major results from this Bureau research. Over a period of several years, the Bureau of Mines conducted six experiments at its Bruceton Experimental Mine in Pennsylvania. The experiments involved sealing the mine after several tons of piled coal had been allowed to burn continuously for 2 to 3 days. Although gas data obtained during the experiments revealed nothing significant, measured smoke particle levels were found to correlate with the stages of combustion and temperatures of the smoldering coal pile. Moreover, it was found that no smoke particles are produced when high-temperature smoldering exists deep within the mass of the coal pile since the smoke particles are filtered by the coal surrounding the hot region. Smoke is emitted into the mine atmosphere only if combustion is occurring near exposed surfaces. As suggested by these findings, any decision to recover a sealed mine area based primarily upon the absence of smoke particles is not a wise derision.

Jan 1, 1988

By Martyn F. Roetter

The work of the operational communication systems' group dealt with a range of communication needs and functions within mines, primarily along haulageways, to and within sections up to the working face itself, and in mine shafts. A mixture of communication techniques and hardware is needed to satisfy this variety of communication needs within the differing environments encountered in U.S. mines. Substantial progress, both experimental and theoretical, has been made in recent years towards developing alternative communication systems suitable for use in mines which are based on "guided" waves, including wire-less (waveguide-like propagation in mine tunnels) and wire-based systems (leaky coaxial cables or wires) . Major priorities identified for further work needed to confirm (or deny) the applicability, and refine the operational specifications of promising communication systems for mine use include: Short-Term Projects o Cost/performance analyses of promising leaky coaxial cable and UHF radio communication systems which require further data from: - Experimental investigation under U.S. mine conditions of the performance of potentially applicable leaky coaxial cable communication systems developed in Europe (France, Belgium, and the U.K). - Cost estimates on these coaxial cable communication systems. - Measurements of UHF radio propagation in low-coal mines. - Investigation of the influence of obstacles (e.g. shuttle cars and section machinery) in the entries on UHF radio propagation in mines. o Investigation of the problems of transmitter and receiver coupling and termination matching associated with the two-way propagation of low frequency radio waves in hoist shafts.

Jan 1, 1973

By Daniel C. Boteler

Data from 68 entrained-bed carbonization tests were treated statistically by the Bureau of Mines, and several useful relationships were developed among the major variables. Nine coals, ranging in rank from lignite A to high-volatile A bituminous, were carbonized in two entrained-bed carbonization pilot plants. The carbonizing reactors employed were vertically mounted cylinders, internally heated, refractory-lined, and 10 inches ID. The range of carbonization temperatures was from 825° to 1,600° F. Using a regression-analysis computer program, empirical equations were developed by which carbonization temperature, air-to-coal ratio, devolatilization of coal, char yield, and volatile matter content of product char may be predicted.

Jan 1, 1973

By Daniel Edelstein

Demand for arsenic trioxide increased markedly during 1984 as a result of increased use of arsenical wood preservatives and increased use of arsenicals in agriculture. The increase in agricultural demand was due to a return to production of land with-held from cotton planting under an agriculture program for acreage diversion for some 1983 crops. Supplies of arsenic trioxide were more than adequate to meet increased demand, and prices either declined from, or remained at, the low 1983 levels. In June, ASARCO Incorporated announced plans to close its Tacoma, WA, smelter by mid-1985. Domestic Data Coverage.-Refined arsenic trioxide was produced by two U.S. companies. The major producer voluntarily reported its production to the Bureau of Mines, but to prevent disclosure of proprietary data, the production data have been withheld.

Jan 1, 1985

By W. E. Robinson

Oil-shale samples selected from a core of the Green River Basin (Wyoming) were studied to ascertain differences in the composition and/or chemical structure of the organic material in the samples relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble kerogen present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extract and upon the aromaticity of the kerogen. In general, it was concluded that significant differences exist in the chemical structure of the oil-shale organic material from various strata within the Green River Formation of Wyoming. Most of the compositional and structural changes were not related to burial depth but were related to source material variations, environmental differences, or other factors.

1.1 Bituminous-Coal and Lignite Dust. - Carboniferous material having a volatile ratio of 12 percent or more by weight and a fineness such that the material passes through a No. 20 sieve. 1.2 Active Underground Workings. - Underground places in which men are required to be or to pass through in the performance of normal mining operations for the production of coal. 1.3 Working Areas. - Underground areas where bituminous coal and lignite are mined, specifically: (a) Face. - The solid surface of the unbroken portion of the coalbed at the advancing end of the working place. (b) Face Area. - The working area inby the last open crosscut in an entry or a room, including the pillar being extracted or longwall being mined. (c) Room. - A place abutting an entry or airway where coal has been mined and extending from the entry or airway to a face. (d) Crosscut (Breakthrough). - Passageways or openings cut through a pillar to connect adjacent entries or rooms. 1.4 Entry. - Underground haulageways, travelways, and airways, except working areas as defined in section 1.3. (a) Active Entry. - An entry in which coal is being mined from a portion thereof or from connected sections. (b) Parallel Entry. - Usually an intake airway parallel to the haulageway. (c) Back Entry. - Usually a return airway parallel to the haulageway.

Jan 1, 1960

By John C. Edwards

A two-dimensional, time-dependent, mathematical model has been developed that describes fire spread along the walls of a ventilated duct. The model is based on the assumption that the leading edge of the fire zone propagating along the wall surface coincides with the isotherm for the fuel ignition temperature. The model includes gas-phase energy transport via radiation and forced convection inside the duct and solid-phase energy transport by conduction into the fuel lining. Product gases emitted from the fire zone are assumed to mix uniformly with the ventilation gas to produce an optically dense gas mixture at the combustion temperature that enters the preheat region. Numerical solutions of the model equations for a coal-lined duct (simulated coal mine entry) have been used to investigate the effects of tube radius, air velocity, combustion temperature, and optical density of the soot-laden gas upon the terminal fire spread rate.

Jan 1, 1977

By C. B. Manula, R. L. Sanford, R. A. Rivell

This report was prepared by The Pennsylvania State University under USBM Contract No. 60111808. The contract was initiated under the coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with M. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines.

Jan 1, 1974

By M. J. Kovalik

Illinois No.6, a high-volatile B coal of low fluidity, was blended with fluidized-bed char and coke breeze to improve the strength of the coke obtained from carbonizing this coal. Twenty-one tests, selected from those made in the small-scale Hanson carbonizer, were carbonized in the BM-AGA 13-inch-diameter, cylindrical retort, with a coal charge of about 90 pounds; the strength of the cokes was determined by the standard ASTM tumbler test. Using the same procedure, 10 tests were made with High Splint, a high-volatile A coal from Harlan County, Ky. Carbonization of the blends produced larger and stronger cokes than did the Illinois No.6 coal singly. The optimum blend contained 6 percent each of char and coke breeze. Further improvement in coke strength was realized by either preheating this blend prior to carbonization or by adding a small pro-portion of a premium blending coal. The former method could possibly eliminate the use of premium coking coals in blends with Illinois No. 6 coal to make an acceptable metallurgical coke. Except for no improvement in coke strength by preheating, results for High Splint coal showed behavior similar to that of the Illinois No.6 coal.

Jan 1, 1973

By James J. Olson

The Bureau of Mines recorded peak particle-velocity levels and vibration frequencies to determine the nature and intensity of ground vibrations for tunnel blast rounds at the NORAD Complex, Colorado Springs, Colo. Previous Bureau of Mines studies in quarries and underground mines had shown that scaling (dividing) the distance from the blast by the square root of the charge weight removed the effect of the various charge weights on vibration amplitudes. The analysis of variance tests performed on the NORAD vibration data, however, indicated that the cube rather than square root scaling exponent grouped the data more effectively. The empirical propagation equation, V = 560 (D/w1/3)-2.04, where V is the maximum peak particle velocity in inches per second, D is the distance from the blast in feet, and W is the zero-delay charge weight in pounds described the attenuation, with distance, of the particle velocities from the tunnel blasts in the Pikes Peak Granite of the NORAD Complex.

Jan 1, 1972

The Bahamas Oil Refining Co. (BORCO) refinery in Freeport continued to operate at less than half its full 500,000-barrel-per-day capacity. Although owned through subsidiaries by the Carey Energy Corp (65%) and Standard Oil Co. of California (35%), BORCO is ineligible for participation in the Crude Oil Entitlements Program granted to companies operating within the United States proper or its territories. Like some other Caribbean refineries, BORCO has suffered a loss of normal market outlet due to the wt advantage afforded U.S. refineries by the Entitlements Program. Saudi Arabia, Nigeria, and Libya are the major suppliers of crude for the refinery. Its principal products, motor spirits, aviation fuel, distillate fuels, and residual fuel oils, were marketed in the United States and Puerto Rim. The Government-owned Bahamas Development Corp. and Burmah Oil Co. Ltd., held discussions pertaining to a renegotiation of Burmah Oil's management contract for the Grand Bahama Oil Transshipment terminal. The desired contract modifications were not made public but financial problems have plagued the terminal and its operation since construction started in 1972.

Jan 1, 1981